水星mw150r v5版导入配置文件重启后变砖了,求助大侠!

人情***

导入配置文件后损坏,不能管理,wlan灯不亮,网口灯正常,可以当交换机使用,买了ttl线但不会使用,求助大仙们!!!
ping 192.168.1.1发送4,返回0,丢失100% 捅屁股没有反应!

下面是SecureCRT返回信息,求助大仙帮我看一下!
完全启动时:
         ________  ________             __      __  ____   _  __   ___
        |________||   ___  |           |  |    |  ||    \ | ||  | /  /
           |  |   |  |___| |   __ __   |  |    |  ||     \| ||  |/  /
           |  |   |   _____|  |__ __|  |  |___ |  || |\     ||      \
           |__|   |__|                 |______||__||_| \____||__|\___\


                            Software Platform for MIPS
Creation date: Jan 25 2011, 15:02:06 (chenyunchuan@tp-link.net)
Copyright(C) 2001-2010 by TP-LINK TECHNOLOGIES CO., LTD.
CPU: AR9330: AP121 Board
CPU freq: 400 MHZ
SDRAM size: 8 MB
ipaddr:192.168.1.1
serverip:192.168.1.100
file:vxWorks.img


Attaching interface lo0... done
Rx clbufs 512 each of size 1756
eth_rx_netpool_init: allocated, pDmaBuf=0x806af110, buffend = 8078b914
ATHRS26: resetting s26
ATHRS26: s26 reset done
eth_rx_netpool_init: done already!
Attached IPv4 interface to eth unit 0
Press Ctrl+C to stop auto-boot...
0
auto-booting...
Uncompressing...LAN Port Interface type is 0x4c04
done
Starting at 0x80001000...

Attaching interface lo0... done
Rx clbufs 528 each of size 1596
eth_rx_netpool_init: allocated, pDmaBuf=0x806a54e0, buffend = 80774124
ATHRS26: resetting s26
ATHRS26: s26 reset done
eth_rx_netpool_init: done already!
Attached IPv4 interface to mirror unit 0
Assertion failed: 0, file ../src/router_config/qos_RouterClassifier.c, line 319

LAN Port Interface type is 0x4c04



启动过程按ctri+c后
         ________  ________             __      __  ____   _  __   ___
        |________||   ___  |           |  |    |  ||    \ | ||  | /  /
           |  |   |  |___| |   __ __   |  |    |  ||     \| ||  |/  /
           |  |   |   _____|  |__ __|  |  |___ |  || |\     ||      \
           |__|   |__|                 |______||__||_| \____||__|\___\


                            Software Platform for MIPS
Creation date: Jan 25 2011, 15:02:06 (chenyunchuan@tp-link.net)
Copyright(C) 2001-2010 by TP-LINK TECHNOLOGIES CO., LTD.
CPU: AR9330: AP121 Board
CPU freq: 400 MHZ
SDRAM size: 8 MB
ipaddr:192.168.1.1
serverip:192.168.1.100
file:vxWorks.img

*
Attaching interface lo0... done
Rx clbufs 512 each of size 1756
eth_rx_netpool_init: allocated, pDmaBuf=0x806af110, buffend = 8078b914
ATHRS26: resetting s26
ATHRS26: s26 reset done
eth_rx_netpool_init: done already!
Attached IPv4 interface to eth unit 0
Press Ctrl+C to stop auto-boot...
Stop auto-boot...
# LAN Port Interface type is 0x4c04

总是卡在0x4c04这

人情***

      经过努力,现在启动信息到这一步了,tftp服务器显示传送完毕,超级终端显示如下,好像是什么命令错误,不知道了!
   ________  ________             __      __  ____   _  __   ___
        |________||   ___  |           |  |    |  ||    \ | ||  | /  /
           |  |   |  |___| |   __ __   |  |    |  ||     \| ||  |/  /
           |  |   |   _____|  |__ __|  |  |___ |  || |\     ||      \
           |__|   |__|                 |______||__||_| \____||__|\___\


                            Software Platform for MIPS
Creation date: Jan 25 2011, 15:02:06 (chenyunchuan@tp-link.net)
Copyright(C) 2001-2010 by TP-LINK TECHNOLOGIES CO., LTD.
CPU: AR9330: AP121 Board
CPU freq: 400 MHZ
SDRAM size: 8 MB
ipaddr:192.168.1.1
serverip:192.168.1.100
file:vxWorks.img


Attaching interface lo0... done
Rx clbufs 512 each of size 1756
eth_rx_netpool_init: allocated, pDmaBuf=0x806af110, buffend = 8078b914
cATHRS26: resetting s26
ATHRS26: s26 reset done
eth_rx_netpool_init: done already!
Attached IPv4 interface to eth unit 0
Press Ctrl+C to stop auto-boot...
cStop auto-boot...
# LAN Port Interface type is 0x4c04

# update vxWorks 192.168.1.100 mw150rv5-cn-up.bin
TFTP from server 192.168.1.100;
our IP address is 192.168.1.1;
Filename 'mw150rv5-cn-up.bin'
Downloading... 1522932
Bad Magic Number,00142FC0
Usage error.

没有大侠知道是怎么回事吗?
update          update [boot | vxWorks] [host] [image]
#

人情***

多谢bsctv指导贴https://www.right.com.cn/forum/thread-78449-1-1.html
,终于救活了我的mw150,现已成功刷为tp740!使用一切正常!固件比水星150多了一个发射功率调节功能,更强大!再次感谢!