HG320路由器TT.netcore固件下刷DD不能启动 附上TTL启动信息

过期***

各位，这个问题我弄了三四天了，实在无法解决，恳请各位帮忙分析一下原因！

HG320，原版电信的系统。买回来后，先刷了dd-wrt.v24-18000_NEWD-2_K2.6_mini.bin系统，在该DD下，刷了sady大侠的CFE，从DD系统刷到了Netcore(NR235W)CN-V1.2(beta5)，又刷到了TT。
每次刷之前和刷之后，在minniweb界面下都有清除NVRAM。

现在的问题：
Netcore的固件和TT的固件可以来回自由的刷，刷后可以正常启动
但是，Netcore系统或者TT系统，在minmiweb界面下，刷了DD后，都无法正常启动。刷之前和刷之后，都在minniweb界面下都有清除过NVRAM，也在TTL中断过CFE，在CFE下也执行过清除NVRAM的命令。刷完DD后，浏览器（遨游浏览器的地址栏有DDwrt的logo)192.168.1.1无法打开 ，google的浏览器也一样。ping 192.168.1.1 -t一直显示time out。修复过网卡连接，没有用。
已经尝试过下面的三个DD版本：
dd-wrt.v24-18000_NEWD-2_K2.6_mini.bin （电信原本系统时成功刷过一次，后再刷无法启动）
dd-wrt.v24-18688_NEWD-2_K2.6_mega.bin
dd-wrt.v24-18688_NEWD-2_K2.6_mini.bin

过期***

刷后DD后的TTL启动信息

1. Decompressing...done
   
2. 
   
3. 
   
4. CFE version 5.60.120.9  based on BBP 1.0.37 for BCM947XX (32bit,SP,LE)
   
5. Build Date: 2011骞05鏈04鏃鏄熸湡涓15:32:36 CST (root@localhost.localdomain)
   
6. Copyright (C) 2000-2008 Broadcom Corporation.
   
7. 
   
8. Init Arena
   
9. Init Devs.
   
10. Boot partition size = 131072(0x20000)
    
11. Found a 16MB ST compatible serial flash
    
12. [CFE][boot][ST Serial flash offset 00000000 size 128KB]
    
13. [CFE][trx][ST Serial flash offset 00020000 size 1KB]
    
14. [CFE][os][ST Serial flash offset 0002001C size 16224KB]
    
15. [CFE][nvram][ST Serial flash offset 00FF8000 size 32KB]
    
16. [CFE][boot][ST Serial flash offset 00000000 size 128KB]
    
17. [CFE][trx0][ST Serial flash offset 00020000 size 1KB]
    
18. [CFE][os0][ST Serial flash offset 0002001C size 8832KB]
    
19. [CFE][trx1][ST Serial flash offset 008C0000 size 1KB]
    
20. [CFE][os1][ST Serial flash offset 008C001C size 7392KB]
    
21. [CFE][nvram][ST Serial flash offset 00FF8000 size 32KB]
    
22. et0: Broadcom BCM47XX 10/100/1000 Mbps Ethernet Controller 5.60.120.9
    
23. CPU type 0x19749: 500MHz
    
24. Tot mem: 65536 KBytes
    
25. 
    
26. CFE mem:    0x80700000 - 0x8079A7D0 (632784)
    
27. Data:       0x807306D0 - 0x80733850 (12672)
    
28. BSS:        0x80733850 - 0x807347D0 (3968)
    
29. Heap:       0x807347D0 - 0x807987D0 (409600)
    
30. Stack:      0x807987D0 - 0x8079A7D0 (8192)
    
31. Text:       0x80700000 - 0x807306C8 (198344)
    
32. 
    
33. Device eth0:  hwaddr 00-00-00-00-51-82, ipaddr 192.168.1.1, mask 255.255.255.0
    
34.         gateway not set, nameserver not set
    
35. cur=
    
36. buf=go;
    
37. Loader:raw Filesys:tftp Dev:eth0 File:: Options:(null)
    
38. Loading: Failed.
    
39. Could not load :: Timeout occured
    
40. Boot from big image !!
    
41. Loader:raw Filesys:raw Dev:flash0.os File: Options:(null)
    
42. Loading: ....... 3907718 bytes read
    
43. Entry at 0x80001000
    
44. Closing network.
    
45. Starting program at 0x80001000
    
46. Linux version 2.6.22 (root@zzyy) (gcc version 4.2.3) #56 PREEMPT Sun Feb 12 22:42:16 CST 2012
    
47. CPU revision is: 00019749
    
48. Found an ST compatible serial flash with 256 64KB blocks; total size 16MB
    
49. Determined physical RAM map:
    
50. memory: 04000000 @ 00000000 (usable)
    
51. Initrd not found or empty - disabling initrd
    
52. Built 1 zonelists.  Total pages: 16256
    
53. Kernel command line: root=/dev/mtdblock2 console=ttyS0,115200 init=/sbin/preinit
    
54. Primary instruction cache 32kB, physically tagged, 4-way, linesize 32 bytes.
    
55. Primary data cache 32kB, 4-way, linesize 32 bytes.
    
56. Synthesized TLB refill handler (20 instructions).
    
57. Synthesized TLB load handler fastpath (32 instructions).
    
58. Synthesized TLB store handler fastpath (32 instructions).
    
59. Synthesized TLB modify handler fastpath (31 instructions).
    
60. PID hash table entries: 256 (order: 8, 1024 bytes)
    
61. CPU: BCM5357 rev 1 at 500 MHz
    
62. Using 250.000 MHz high precision timer.
    
63. Console: colour dummy device 80x25
    
64. Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
    
65. Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
    
66. Memory: 60372k/65536k available (3017k kernel code, 5100k reserved, 567k data, 232k init, 0k highmem)
    
67. Mount-cache hash table entries: 512
    
68. NET: Registered protocol family 16
    
69. PCI: no core
    
70. PCI: no core
    
71. PCI: Fixing up bus 0
    
72. NET: Registered protocol family 2
    
73. Time: MIPS clocksource has been installed.
    
74. IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
    
75. TCP established hash table entries: 2048 (order: 2, 16384 bytes)
    
76. TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
    
77. TCP: Hash tables configured (established 2048 bind 2048)
    
78. TCP reno registered
    
79. squashfs: version 3.2-r2 (2007/01/15) Phillip Lougher
    
80. fuse init (API version 7.8)
    
81. io scheduler noop registered (default)
    
82. Serial: 8250/16550 driver $Revision: 1.1.1.1 $ 4 ports, IRQ sharing disabled
    
83. serial8250: ttyS0 at MMIO 0x0 (irq = 8) is a 16550A
    
84. RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize
    
85. loop: module loaded
    
86. PPP generic driver version 2.4.2
    
87. PPP Deflate Compression module registered
    
88. PPP BSD Compression module registered
    
89. PPP MPPE Compression module registered
    
90. NET: Registered protocol family 24
    
91. PPTP driver version 0.8.4
    
92. pflash: found no supported devices
    
93. sflash: squash filesystem with lzma found at block 1465
    
94. Creating 4 MTD partitions on "sflash":
    
95. 0x00000000-0x00020000 : "boot"
    
96. 0x00020000-0x00ff0000 : "linux"
    
97. 0x0016e764-0x00ff0000 : "rootfs"
    
98. 0x00ff0000-0x01000000 : "nvram"
    
99. hbwrr_reg:0
    
100. u32 classifier
     
101. nf_conntrack version 0.5.0 (512 buckets, 4096 max)
     
102. nf_ct_ftp: registering helper for pf: 2 port: 21
     
103. nf_ct_ftp: registering helper for pf: 10 port: 21
     
104. ip_tables: (C) 2000-2006 Netfilter Core Team
     
105. ClusterIP Version 0.8 loaded successfully
     
106. arp_tables: (C) 2002 David S. Miller
     
107. mid :0, nr = 6
     
108. mid :1, nr = 12
     
109. mid :2, nr = 2
     
110. mid :3, nr = 10
     
111. mid :4, nr = 34
     
112. mid :5, nr = 15
     
113. mid :6, nr = 25
     
114. mid :7, nr = 12
     
115. mid :8, nr = 3
     
116. net sniffer init ok.
     
117. igd_port_trigger_init:[559]register port trigger
     
118. TCP cubic registered
     
119. NET: Registered protocol family 1
     
120. NET: Registered protocol family 17
     
121. NET: Registered protocol family 15
     
122. mirror create proc success
     
123. 802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
     
124. All bugs added by David S. Miller <davem@redhat.com>
     
125. NETCORE fastpath V0.03
     
126. VFS: Mounted root (squashfs filesystem) readonly.
     
127. Freeing unused kernel memory: 232k freed
     
128. Failed to execute /init
     
129. Failed to execute /sbin/preinit.  Attempting defaults...
     
130. init started:  BusyBox v1.1.2 (2012.02.08-08:33+0000) multi-call binary
     
131. Starting pid 15, console /dev/ttyS0: '/etc/rcS'
     
132. Algorithmics/MIPS FPU Emulator v1.5
     
133. /etc/rcS: /etc/rcS: 2: /var/run: not found
     
134. file /var/parame/parame/param.tmp size error 0
     
135. emf: module license 'Proprietary' taints kernel.
     
136. et_module_init: passivemode set to 0x0
     
137. mirror create proc success
     
138. eth0: Broadcom BCM47XX 10/100/1000 Mbps Ethernet Controller 5.100.138.4
     
139. wl_module_init: passivemode set to 0x0
     
140. eth1: Broadcom BCM4347 802.11 Wireless Controller 5.100.138.7
     
141. device vlan1 entered promiscuous mode
     
142. device eth1 entered promiscuous mode
     
143. vlan1: dev_set_promiscuity(master, 1)
     
144. device eth0 entered promiscuous mode
     
145. br0: port 2(eth1) entering learning state
     
146. br0: port 1(vlan1) entering learning state
     
147. br0: topology change detected, propagating
     
148. br0: port 2(eth1) entering forwarding state
     
149. br0: topology change detected, propagating
     
150. br0: port 1(vlan1) entering forwarding state
     
151. cp: /bin/ntpara: No such file or directory
     
152. parame restroe default
     
153. tar: /tmp/param.file: No such file or directory
     
154. tar: Error exit delayed from previous errors
     
155. [tar_flag : 702] : tar OK !
     
156. 
     
157. Starting Protocol Module: procfs                           ... OK!
     
158. DEBUG:genmac:57 sizeof retval=4
     
159. DEBUG:genmac:66 d=84148994
     
160. DEBUG:genmac:75 MAC:000102030405
     
161. DEBUG:genmac:66 d=100926210
     
162. DEBUG:genmac:75 MAC:000102030406
     
163. DEBUG:genmac:66 d=117703426
     
164. DEBUG:genmac:75 MAC:000102030407
     
165. Starting Protocol Module: igd interface                    ... OK!
     
166. Starting Protocol Module: ifstate                          ... OK!
     
167. Starting Protocol Module: misc                             ... OK!
     
168. Starting Protocol Module: ddns                             ... OK!
     
169. RTNETLINK answers: No such file or directory
     
170. RTNETLINK answers: No such file or directory
     
171. RTNETLINK answers: No such file or directory
     
172. RTNETLINK answers: No such file or directory
     
173. Starting Protocol Module: route                            ... OK!
     
174. Starting Protocol Module: storm                            ... OK!
     
175. Starting Protocol Module: igd filter                       ... OK!
     
176. Starting Protocol Module: webs                             ... OK!
     
177. Starting Protocol Module: dhcp                             ... OK!
     
178. Starting Protocol Module: nat                              ... OK!
     
179. Starting Protocol Module: DNS                              ... OK!
     
180. Starting Protocol Module: arp                              ... OK!
     
181. Starting Protocol Module: dnsmasq                          ... OK!
     
182. Starting Protocol Module: Super dmz                        ... OK!
     
183. Starting Protocol Module: log                              ... OK!
     
184. Starting Protocol Module: WIFI                             ... OK!
     
185. Register Hardware Module: bcm535x bsp                      ...
     
186. bcm535x_wifi msg:117-00
     
187. 
     
188. Ok!
     
189. 
     
190. Starting Protocol Module: Port                             .igd_filter_netlink_rcvmsg[line=7370] no such type, type = 20
     
191. .. OK!
     
192. Registerigd_filter_netlink_rcvmsg[line=7370] no such type, type = 25
     
193. Hardware Module: Port driver                      ...
     
194. Ok!
     
195. 
     
196. Starting Protocigd_filter_netlink_rcvmsg[line=7370] no such type, type = 26
     
197. ol Module: host igd_filter_netlink_rcvmsg[line=7370] no such type, type = 22
     
198.                             ... OK!
     
199. Starting Protocol Module: igd pppoe server                 ... OK!
     
200. Starting Protocol Module: igd ip pool  igd_filter_netlink_rcvmsg[line=7370] no such type, type = 102
     
201.                 igd_filter_netlink_rcvmsg[line=7370] no such type, type = 102
     
202.     ... OK!
     
203. check this:igd_ip_pool_proc[268]msg 5 doesn't support
     
204. 
     
205. check this:igd_generic_load_param[840]/tmigd_filter_netlink_rcvmsg[line=7370] no such type, type = 32
     
206. p/igd_ip_pool.file read error, restore default
     
207. 
     
208. check this:igd_ip_pool_proc[2nf_ct_ftp: port already exist! port = 21
     
209. 68]msg 5 doesn'tigd_filter_netlink_rcvmsg[line=7370] no such type, type = 32
     
210. support
     
211. 
     
212. [igd_iptc_lan2lan:1275]
     
213. check this:igd_ip_pool_proc[268]msg 5 doesn't support
     
214. 
     
215. check this:igd_generic_load_param[840]/tmp/igd_iigd_filter_netlink_rcvmsg[line=7370] no such type, type = 102
     
216. p_pool.file read error, restore default
     
217. 
     
218. check this:igd_ip_pool_proc[268]msg 5 doesn't support
     
219. 
     
220. portmirror_set : line_number = 1371 error nr = 160773
     
221. 
     
222. 
     

复制代码

过期***

1. Starting Protocol Module: QOS                              ... OK!
   
2. DEBUG:genmac:57 sizeof retval=4
   
3. DEBUG:genmac:66 d=84148994
   
4. DEBUG:genmac:75 MAC:000102030405
   
5. DEBUG:genmac:66 d=100926210
   
6. DEBUG:genmac:75 MAC:000102030406
   
7. DEBUG:genmac:66 d=117703426
   
8. DEBUG:genmac:75 MAC:000102030407
   
9. if_set_ispmap_bbr0: port 2(eth1) entering disabled state
   
10. y_if_id:isp = 0,br0: port 1(vlan1) entering disabled state
    
11. currently ifmap = 0x1.
    
12. 
    
13. br0: port 2(eth1) entering learning state
    
14. br0: port 1(vlan1) entering learning state
    
15. br0: topology change detected, propagating
    
16. br0: port 2(eth1) entering forwarding state
    
17. br0: topology change detected, propagating
    
18. br0: port 1(vlan1) entering forwarding state
    
19. igd_filter_netlink_rcvmsg[line=7370] no such type, type = 102
    
20. igd_filter_netlink_rcvmsg[line=7370] no such type, type = 28
    
21. igd_filter_netlink_rcvmsg[line=7370] no such type, type = 27
    
22. igd_filter_netlink_rcvmsg[line=7370] no such type, type = 27
    
23. igd_filter_netlink_rcvmsg[line=7370] no such type, type = 28
    
24. #####:igd_superdmz.c:igd_route_mixnet_refresh:1222: flags = 0
    
25. igd_filter_netlink_rcvmsg[line=7370] no such type, type = 28
    
26. igd_filter_netlink_rcvmsg[line=7370] no such type, type = 27
    
27. DEBUG:arp_socket_init:90 ifindex = 7
    
28. device br0 entered promiscuous mode
    
29. DEBUG:arp_socket_init:145 sock=11
    
30. DEBUG:nb_socket_init:87 nb_socket=12
    
31. DEBUG:port_fsm:2135 WAN1 INIT -> DOWN
    
32. DEBUG:port_fsm:2138 vlan2,vlan2
    
33. Nothing to flush.
    
34. Nothing to flush.
    
35. igd_filter_netlink_rcvmsg[line=7370] no such type, type = 28
    
36. igd_filter_netlink_rcvmsg[line=7370] no such type, type = 27
    
37. igd_filter_netlink_rcvmsg[line=7370] no such type, type = 27
    
38. igd_filter_netlink_rcvmsg[line=7370] no such type, type = 27
    
39. bcm535x_wifi msg:117-06
    
40. 
    
41. bcm535x_wifi msg:117-06
    
42. 
    
43. bcm535x_wifi msg:117-03
    
44. 
    
45. WIFI_HW_APPLY,ssid=Netcore
    
46. 
    
47. br0: port 2(eth1) entering disabled state
    
48. interface wl0.1 does not exist!
    
49. SIOCGIFFLAGS: No such device
    
50. killall: wps_monitor: no process killed
    
51. killall: wps_ap: no process killed
    
52. killall: nas: no process killed
    
53. killall: eapd: no process killed
    
54. __bcm535x_hw_apply mode:ap
    
55. 
    
56. bandwidth:4
    
57. 
    
58. WDS configure,mode:0
    
59. acl_mode:0
    
60. 
    
61. wps_device_pin:01976373
    
62. bandwidth:4
    
63. 
    
64. br0: port 2(eth1) entering learning state
    
65. br0: topology change detected, propagating
    
66. br0: port 2(eth1) entering forwarding state
    
67. eth1: Operation not permitted
    
68. wlconf: PHYTYPE: 4
    
69. eth1: Invalid argument
    
70. eth1: Invalid argument
    
71. eth1: Operation not supported
    
72. eth1: Invalid argument
    
73. eth1: Invalid argument
    
74. eth1: Invalid argument
    
75. eth1: Invalid argument
    
76. eth1: Invalid argument
    
77. eth1: Invalid argument
    
78. eth1: Invalid argument
    
79. eth1: Invalid argument
    
80. eth1: Invalid argument
    
81. eth1: Invalid argument
    
82. COEX: downgraded chanspec 0x2e05 to 0x2b07: channel 1 used by exiting BSSs
    
83. COEX: downgraded chanspec 0x2e08 to 0x2b0a: channel 3 used by exiting BSSs
    
84. COEX: downgraded chanspec 0x2e09 to 0x2b0b: channel 5 used by exiting BSSs
    
85. COEX: downgraded chanspec 0x2d03 to 0x2b01: channel 2 used by exiting BSSs
    
86. killall: wps_monitor: no process killed
    
87. killall: wps_ap: no process killed
    
88. killall: wps_enr: no process killed
    
89. start wps,pid:103
    
90. 
    
91. txp=7f
    
92. WIFI_HW_APPLY,ret:0
    
93. 
    
94. 
    
95. ### wps_wfi_init(): <wl0_wfi_enable=(null)>WFI is not enabled ###
    
96. eth1: Operation not permitted
    
97. wlconf: PHYTYPE: 4
    
98. eth1: Invalid argument
    
99. eth1: Invalid argument
    
100. eth1: Operation not supported
     
101. Create daemon...
     
102. Create server
     
103. Please press Enter to activate this console. COEX: downgraded chanspec 0x2e05 to 0x2b07: channel 1 used by exiting BSSs
     
104. COEX: downgraded chanspec 0x2e08 to 0x2b0a: channel 3 used by exiting BSSs
     
105. COEX: downgraded chanspec 0x2e09 to 0x2b0b: channel 5 used by exiting BSSs
     
106. COEX: downgraded chanspec 0x2d03 to 0x2b01: channel 3 used by exiting BSSs
     
107. igd_filter_netlink_rcvmsg[line=7370] no such type, type = 102
     
108. igd_filter_netlink_rcvmsg[line=7370] no such type, type = 28
     
109. igd_filter_netlink_rcvmsg[line=7370] no such type, type = 27
     
110. igd_filter_netlink_rcvmsg[line=7370] no such type, type = 28
     
111. igd_filter_netlink_rcvmsg[line=7370] no such type, type = 27
     
112. igd_filter_netlink_rcvmsg[line=7370] no such type, type = 28
     
113. igd_filter_netlink_rcvmsg[line=7370] no such type, type = 28
     
114. igd_filter_netlink_rcvmsg[line=7370] no such type, type = 27
     
115. igd_filter_netlink_rcvmsg[line=7370] no such type, type = 33
     
116. bcm535x_wifi msg:117-10
     
117. 
     
118. get chanspec
     
119. get chanspec 00002e05
     
120. current channel:7,noise:80 bw:40
     
121. get rf status,ret:0
     
122. bcm535x_wifi msg:117-03
     
123. 
     
124. WIFI_HW_APPLY,ssid=Netcore
     
125. 
     
126. br0: port 2(eth1) entering disabled state
     
127. __bcm535x_hw_apply mode:ap
     
128. 
     
129. bandwidth:4
     
130. 
     
131. WDS configure,mode:0
     
132. acl_mode:0
     
133. 
     
134. wps_device_pin:01976373
     
135. bandwidth:4
     
136. 
     
137. br0: port 2(eth1) entering learning state
     
138. br0: topology change detected, propagating
     
139. br0: port 2(eth1) entering forwarding state
     
140. wlconf: PHYTYPE: 4
     
141. start wps,pid:145
     
142. 
     
143. txp=7f
     
144. WIFI_HW_APPLY,ret:0
     

复制代码

hous***

用修改过的CFE，刷DD只能无线连接

过期***

谢谢楼上的回答。非常感谢！

tang***

housecall 发表于 2012-3-18 20:10
用修改过的CFE，刷DD只能无线连接

我无线DD都不稳定，老是重新启动，连接不了啊

tang***

过期的可乐 发表于 2012-3-18 22:43
谢谢楼上的回答。非常感谢！

我无线DD都不稳定，老是重新启动，连接不了啊，搞定了吗？我也遇到这个问题，麻烦说说怎么搞的