求助，TTl刷机遇到的问题

笨***

TTL出现以下内容然后就没有了，请问是什么原因？（如果不接TTL线能正常启动）波特率12800（波特率115200乱码更厉害）

如果在启动过程中接上TTL线能出现以下内容（波特率115200）

[10:59:20.750]收←◆酈ooW藵丄th瀹k丄R93)\0
[10:59:20.890]收←◆峀inux version 2.6.31--LSDK-9.2.0_U11.14-svn1230 (root@xasoft77) (gcc version 4.3.3 (GCC) ) #2 Mon Nov 4 18:24:37 CST 2013
flash_size passed from bootloader = 8
arg 1: console=ttyS0,115200
arg 2: root=/dev/mtdblock2
arg 3: rootfstype=squashfs
arg 4: init=/sbin/init
arg 5: mtdparts=ath-nor0:256k(u-boot),64k(u-boot-env),5312k(rootfs),1408k(uImage),1024k(2ndfile),64k(ART),64k(mib0)
arg 6: mem=64M
CPU revision is: 0001974c (MIPS 74Kc)
ath_sys_frequency: cpu srif ddr srif cpu 560 ddr 450 ahb 225
Determined physical RAM map:
memory: 02000000 @ 00000000 (usable)
User-defined physical RAM map:
memory: 04000000 @ 00000000 (usable)
Initrd not found or empty - disabling initrd
Zone PFN ranges:
  Normal   0x00000000 -> 0x00004000
Movable zone start PFN for each node
early_node_map[1] active PFN ranges
    0: 0x00000000 -> 0x00004000
Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 16256
Kernel command line: console=ttyS0,115200 root=/dev/mtdblock2 rootfstype=squashfs init=/sbin/init mtdparts=ath-nor0:256k(u-boot),64k(u-boot-env),5312k(rootfs),1408k(uImage),1024k(2ndfile),64k(ART),64k(mib0) mem=64M
PID hash table entries: 256 (order: 8, 1024 bytes)
Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
Writing ErrCtl register=00000000
Readback ErrCtl register=00000000
Memory: 46596k/65536k available (2456k kernel code, 18868k reserved, 1181k data, 160k init, 0k highmem)
NR_IRQS:128
plat_time_init: plat time init done
Calibrating delay loop... 279.55 BogoMIPS (lpj=559104)
Mount-cache hash table entries: 512

****************ALLOC***********************
Packet mem: 803c9dc0 (0xe00000 bytes)
********************************************

NET: Registered protocol family 16
netlink_init.
***** Warning *****: PCIe WLAN H/W not found !!!
bio: create slab <bio-0> at 0
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 2048 (order: 2, 16384 bytes)
TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
TCP: Hash tables configured (established 2048 bind 2048)
TCP reno registered
NET: Registered protocol family 1
ATH GPIOC major 0
squashfs: version 4.0 (2009/01/31) Phillip Lougher
JFFS2 version 2.2 (ZLIB) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
fuse init (API version 7.12)
msgmni has been set to 91
alg: No test for lzma (lzma-generic)
alg: No test for stdrng (krng)
io scheduler noop registered
io scheduler deadline registered (default)
led_init!
led_probe!
lct_led_init!
button_init
key_def_init
drivers/char/lct_button.c (key_def_init) GPIO_WPS_RST_KEY: 2
irq_num is 34,gpio is 2
Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled
serial8250.0: ttyS0 at MMIO 0xb8020000 (irq = 19) is a 16550A
console [ttyS0] enabled
brd: module loaded
tun: Universal TUN/TAP device driver, 1.6
tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
7 cmdlinepart partitions found on MTD device ath-nor0
Creating 7 MTD partitions on "ath-nor0":
0x000000000000-0x000000040000 : "u-boot"
0x000000040000-0x000000050000 : "u-boot-env"
0x000000050000-0x000000580000 : "rootfs"
0x000000580000-0x0000006e0000 : "uImage"
0x0000006e0000-0x0000007e0000 : "2ndfile"
0x0000007e0000-0x0000007f0000 : "ART"
0x0000007f0000-0x000000800000 : "mib0"
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver

[10:59:21.281]收←◆Port Status 1c000004
ath-ehci ath-ehci.0: ATH EHCI
ath-ehci ath-ehci.0: new USB bus registered, assigned bus number 1
ehci_reset Intialize USB CONTROLLER in host mode: 13
ehci_reset Port Status 1c000000
ath-ehci ath-ehci.0: irq 3, io mem 0x1b000000
ehci_reset Intialize USB CONTROLLER in host mode: 13
ehci_reset Port Status 1c000000
ath-ehci ath-ehci.0: USB 2.0 started, EHCI 1.00
usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb1: Product: ATH EHCI
usb usb1: Manufacturer: Linux 2.6.31--LSDK-9.2.0_U11.14-svn1230 ehci_hcd
usb usb1: SerialNumber: platform
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
usbcore: registered new interface driver usblp
nf_conntrack version 0.5.0 (1024 buckets, 4096 max)
ip_tables: (C) 2000-2006 Netfilter Core Team
TCP cubic registered
NET: Registered protocol family 10
lo: Disabled Privacy Extensions
Mobile IPv6
ip6_tables: (C) 2000-2006 Netfilter Core Team
IPv6 over IPv4 tunneling driver
sit0: Disabled Privacy Extensions
ip6tnl0: Disabled Privacy Extensions
NET: Registered protocol family 17
802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
All bugs added by David S. Miller <davem@redhat.com>
arch/mips/atheros/gpio.c (ath_simple_config_init) JUMPSTART_GPIO: 16
ath_simple_config_init...725..
ath_simple_config_init...727..
athwdt_init: Registering WDT success
ath_otp_init: Registering OTP success
ath_clksw_init: Registering Clock Switch Interface success
VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
Freeing unused kernel memory: 160k freed

[10:59:22.062]收←◆init started:  BusyBox v1.01 (2013.11.04-10:24+0000) multi-call binary
init started:  BusyBox v1.01 (2013.11.04-10:24+0000) multi-call binary

[10:59:22.109]收←◆Starting pid 165, console /dev/ttyS0: '/etc/rc.d/rcS'

[10:59:22.515]收←◆Starting the hotplug events dispatcher udevd

[10:59:23.062]收←◆Synthesizing initial hotplug events

[10:59:23.140]收←◆Jan  1 00:00:02 udevd[181]: main: the kernel does not support inotify, udevd can't monitor rules file changes

[10:59:23.437]收←◆ATHR_GMAC: Length per segment 1536
ATHR_GMAC: fifo cfg 3 01f00140
ATHR_GMAC: RX TASKLET - Pkts per Intr:16
ATHR_GMAC: Mac address for unit 0:bfff0000
ATHR_GMAC: ff:ff:ff:ff:ff:ff

[10:59:24.000]收←◆mac:0 Registering S27....
ATHR_GMAC: Max segments per packet :   1
ATHR_GMAC: Max tx descriptor count :   128
ATHR_GMAC: Max rx descriptor count :   128
ATHR_GMAC: Mac capability flags    :   2580
ATHR_GMAC: RX TASKLET - Pkts per Intr:16
ATHR_GMAC: Mac address for unit 1:bfff0006
ATHR_GMAC: ff:ff:ff:ff:ff:ff

[10:59:24.578]收←◆mac:1 Registering S27....
ATHR_GMAC: Max segments per packet :   1
ATHR_GMAC: Max tx descriptor count :   128
ATHR_GMAC: Max rx descriptor count :   128
ATHR_GMAC: Mac capability flags    :   2D80

[10:59:24.718]收←◆Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.

[10:59:24.828]收←◆usbcore: registered new interface driver cdc_ether

[10:59:24.906]收←◆usbcore: registered new interface driver usbserial
usbserial: USB Serial Driver core

[10:59:24.953]收←◆USB Serial support registered for GSM modem (1-port)
usbcore: registered new interface driver option
option: v0.7.2:USB Driver for GSM modems

[10:59:25.062]收←◆usbcore: registered new interface driver lc_ether
SIOCGIFFLAGS: No such device
tar: /sbin/debug.tgz: No such file or directory
**** drop_caches_sysctl_handler: all done timer added ...****

[10:59:25.156]收←◆/etc/rc.d/rcS: 98: openvirtual**: not found

[10:59:25.515]收←◆done
Starting pid 31
[10:59:26.531]收←◆
(none) mips #2 Mon Nov 4 18:24:37 CST 2013 (none)
(none) login:
[10:59:32.343]收←◆asf: module license 'Proprietary' taints kernel.
Disabling lock debugging due to kernel taint

[10:59:33.421]收←◆ath_hal: 0.9.17.1 (AR5416, AR9380, REGOPS_FUNC, WRITE_EEPROM, 11D)

[10:59:33.578]收←◆usb 1-1: new high speed USB device using ath-ehci and address 2

[10:59:33.718]收←◆usb 1-1: New USB device found, idVendor=1c9e, idProduct=9b05
usb 1-1: New USB device strings: Mfr=2, Product=3, SerialNumber=4
usb 1-1: Product: USB Modem
usb 1-1: Manufacturer: USB Modem
usb 1-1: configuration #1 chosen from 1 choice
option 1-1:1.0: GSM modem (1-port) converter detected
usb 1-1: GSM modem (1-port) converter now attached to ttyUSB0
option 1-1:1.1: GSM modem (1-port) converter detected
usb 1-1: GSM modem (1-port) converter now attached to ttyUSB1
option 1-1:1.2: GSM modem (1-port) converter detected
usb 1-1: GSM modem (1-port) converter now attached to ttyUSB2
option 1-1:1.3: GSM modem (1-port) converter detected
usb 1-1: GSM modem (1-port) converter now attached to ttyUSB3

[10:59:33.937]收←◆ath_rate_atheros: Copyright (c) 2001-2005 Atheros Communications, Inc, All Rights Reserved

[10:59:34.859]收←◆device dummy0 entered promiscuous mode

[10:59:34.890]收←◆ath_dfs: Version 2.0.0
Copyright (c) 2005-2006 Atheros Communications, Inc. All Rights Reserved

[10:59:34.937]收←◆br0: port 1(dummy0) entering forwarding state

[10:59:35.015]收←◆device eth0 entered promiscuous mode
athr_gmac_ring_alloc Allocated 2048 at 0x82d1e000
athr_gmac_ring_alloc Allocated 2048 at 0x82dd5800

[10:59:35.328]收←◆WASP ----> S27 PHY MDIO
Setting Drop CRC Errors, Pause Frames and Length Error frames
Setting PHY...

[10:59:38.937]收←◆ath_dev: Copyright (c) 2001-2007 Atheros Communications, Inc, All Rights Reserved

[10:59:39.968]收←◆ath_ahb: 9.2.0_U11.14 (Atheros/multi-bss)
__ath_attach: Set global_scn[0]
ACBKMinfree = 48
ACBEMinfree = 32
ACVIMinfree = 16
ACVOMinfree = 0
CABMinfree = 48
UAPSDMinfree = 0
Wasp Enterprise mode: 0x00000000
Restoring Cal data from Flash
Using Cal data from Flash 0x9f7e0000
dfs_attach: use DFS enhancements
DFS min filter rssiThresh = 18
DFS max pulse dur = 151 ticks
ath_get_caps[5184] rx chainmask mismatch actual 3 sc_chainmak 0
ath_get_caps[5159] tx chainmask mismatch actual 3 sc_chainmak 0
ADDRCONF(NETDEV_UP): eth0: link is not ready
SC Callback Registration for wifi0
wifi0: Atheros 9340: mem=0xb8100000, irq=2
ath_pci: 9.2.0_U11.14 (Atheros/multi-bss)

[10:59:40.250]收←◆device eth1 entered promiscuous mode
athr_gmac_ring_alloc Allocated 2048 at 0x83b04000
athr_gmac_ring_alloc Allocated 2048 at 0x82dd7800

[10:59:40.562]收←◆WASP ----> S27 PHY MDIO
ATHRS27: resetting s27

[10:59:40.671]收←◆ATHRS27: s27 reset done
Setting Drop CRC Errors, Pause Frames and Length Error frames
Setting PHY...

[10:59:41.718]收←◆ADDRCONF(NETDEV_UP): eth1: link is not ready

[10:59:42.031]收←◆to start lc_debut_ctl thread!

[10:59:42.140]收←◆wlan_vap_create : enter. devhandle=0x82df82c0, opmode=IEEE80211_M_HOSTAP, flags=0x1
wlan_vap_create : exit. devhandle=0x82df82c0, opmode=IEEE80211_M_HOSTAP, flags=0x1.
wlan_vap_create : enter. devhandle=0x82df82c0, opmode=IEEE80211_M_HOSTAP, flags=0x1
wlan_vap_create : exit. devhandle=0x82df82c0, opmode=IEEE80211_M_HOSTAP, flags=0x1.

[10:59:42.234]收←◆wlan_vap_create : enter. devhandle=0x82df82c0, opmode=IEEE80211_M_HOSTAP, flags=0x1
wlan_vap_create : exit. devhandle=0x82df82c0, opmode=IEEE80211_M_HOSTAP, flags=0x1.

[10:59:42.296]收←◆wlan_vap_create : enter. devhandle=0x82df82c0, opmode=IEEE80211_M_HOSTAP, flags=0x1
wlan_vap_create : exit. devhandle=0x82df82c0, opmode=IEEE80211_M_HOSTAP, flags=0x1.

[10:59:45.265]收←◆lct_led_open!

[10:59:45.906]收←◆dfs_init_radar_filters: Unknown dfs domain 0

[10:59:46.015]收←◆Setting Max Stations:32

[10:59:46.734]收←◆ ieee80211_ioctl_siwmode: imr.ifm_active=131712, new mode=3, valid=1
DEVICE IS DOWN ifname=ath0

[10:59:47.125]收←◆ DEVICE IS DOWN ifname=ath0

[10:59:53.781]收←◆device ath0 entered promiscuous mode
br0: port 4(ath0) entering forwarding state

[10:59:53.890]收←◆ADDRCONF(NETDEV_UP): wan0: link is not ready
ifr.ifr_name = wan0

[10:59:54.484]收←◆ndis open exit.
ndis_get_lib_version:get version=1.5

邪恶***

有没有换一个终端软件试试???

笨***

还没有我试试看

笨***

邪恶海盗 发表于 2017-12-14 12:05
有没有换一个终端软件试试???

securecrt 也是一样的

邪恶***

笨笨瀦 发表于 2017-12-14 12:40
securecrt 也是一样的

TTL小板用的是哪种?
我以前碰到过,把LED灯拆掉后正常的

笨***

邪恶海盗 发表于 2017-12-14 13:17
TTL小板用的是哪种?
我以前碰到过,把LED灯拆掉后正常的

ch314apro   

用户名***

换Xshell试试看。

笨***

用户名被谁抢注 发表于 2017-12-14 21:02
换Xshell试试看。

一样是乱码，并且路由也一样是卡着不能启动

笨***

有没有大神可以帮忙解决啊