麻烦大神帮我看下TTL信息

左手♂牵右手

前面发过帖，E2000砖了。经人讲解接入TTL线
按住CTRL+C后进入CFE模式
但是出现以下信息    麻烦会的人帮我看下
PING自从开启电源后一直是100   
TFTP上传99次一直是失败
是不是还要输入什么命令啊



以下是信息
CFE version 5.10.56.51 based on BBP 1.0.37 for BCM947XX (32bit,SP,LE)
Build Date: Fri Oct  8 08:52:14 HKT 2010 (hue@sw1)
Copyright (C) 2000-2008 Broadcom Corporation.

Init Arena
Init Devs.

No DPN
This is a Serial Flash
Boot partition size = 262144(0x40000)
Found a 8MB ST compatible serial flash
Partition information:
boot    #00   00000000 -> 0003FFFF  (262144)
trx     #01   00040000 -> 0004001B  (28)
os      #02   0004001C -> 007F0FFF  (8064996)
nvram   #03   007F1000 -> 007FFFFF  (61440)
Partition information:
boot    #00   00000000 -> 0003FFFF  (262144)
trx     #01   00040000 -> 007F0FFF  (8065024)
nvram   #02   007F1000 -> 007FFFFF  (61440)
BCM47XX_GMAC_ID
et0: Broadcom BCM47XX 10/100/1000 Mbps Ethernet Controller 5.10.56.51
CPU type 0x19740: 354MHz
Tot mem: 32768 KBytes

CFE mem:    0x80700000 - 0x807A1350 (660304)
Data:       0x80733430 - 0x807366F0 (12992)
BSS:        0x807366F0 - 0x8073B350 (19552)
Heap:       0x8073B350 - 0x8079F350 (409600)
Stack:      0x8079F350 - 0x807A1350 (8192)
Text:       0x80700000 - 0x80733428 (209960)

Boot version: v5.4
The boot is CFE
Nothing...

### CLKDIV= 0x80a082c, SFlashClkDiv=8 clkdivsf=2 ###
### Change it to 0x20a082c (2) ###
CMD: [ifconfig eth0 -addr=192.168.1.1 -mask=255.255.255.0]
Device eth0:  hwaddr C0-C1-C0-47-6D-58, ipaddr 192.168.1.1, mask 255.255.255.0
        gateway not set, nameserver not set
CMD: [go;]
Check CRC of image1
  Len:     0x6CD000     (7131136)       (0xBC040000)
  Offset0: 0x1C         (28)            (0xBC04001C)
  Offset1: 0xAD8        (2776)  (0xBC040AD8)
  Offset2: 0xE4800      (935936)        (0xBC124800)
  Header CRC:    0x6B4CE854
  Calculate CRC: 0x6B4CE854
Image 1 is OK
Try to load image 1.
Waiting for 5 seconds to upgrade ...
CMD: [load -raw -addr=0x807a1350 -max=0x185ecb0 :]
Loader:raw Filesys:tftp Dev:eth0 File:: Optionsnull)
Loading: _tftpd_open(): retries=0/5

### Start=464638217 E=465628568 Delta=990351 ###
Failed.
Could not load :: Interrupted
CFE> ^C
CFE>







gpio                Set GPIO.
upgrade             Upgrade Firmware
et                  Broadcom Ethernet utility.
modify              Modify flash data.
nvram               NVRAM utility.
reboot              Reboot.
flash               Update a flash memory device
batch               Load a batch file into memory and execute it
go                  Verify and boot OS image.
boot                Load an executable file into memory and execute it
load                Load an executable file into memory without executing it
save                Save a region of memory to a remote file via TFTP
ping                Ping a remote IP host.
arp                 Display or modify the ARP Table
ifconfig            Configure the Ethernet interface
show clocks         Show current values of the clocks.
show devices        Display information about the installed devices.
unsetenv            Delete an environment variable.
printenv            Display the environment variables
setenv              Set an environment variable.
help                Obtain help for CFE commands

For more information about a command, enter 'help command-name'
*** command status = 0
CFE>

xll

upgrade吧

左手♂牵右手

闲杂状况是进入CFE模式FLASH下后可以上传。但是上传完毕后提示另外英文
等待高人啊
Reading :: _tftpd_open(): retries=0/5
_tftpd_open(): retries=1/5
Done. 5444608 bytes read
fname=flash1.trx
CODE Pattern is correct! (32XN)
Programming...done. 5444576 bytes written
*** command status = 0

bnnyygy

我在想 中断了以后  电脑手动设置IP 能不能进 MINIWEB？

wxm2002

CODE Pattern is correct! (32XN 是不是固件不对啊