（求助）大神帮忙看看TTL信息，哪里出问题了

七里郭

U-Boot 1.1.3 (Jan  7 2014 - 20:48:20)

SoC:Ralink RT3052
DRAM:  Memory Testing.....65536K OK. is 64 MB
relocate_code Pointer at: 83fac000
config usb..

Flash JEDEC Info:
Manufacturer ID:0x00000001
Device ID:0x0000227E
Mode ID:0x00002221
Part ID:0x00002201

FLASH:S29GL128P/N, SIZE:16 MBytes SECTOR:128
S29GLXXX:set sect_size =0x20000
*** Warning - bad CRC, using default environment

_______________________________________________________________
|    ____                 _                 ____               |
|   |  _ \ __ _ _ __   __| | ___  _ __ __ _| __ )  _____  __   |
|   | |_) / _` | '_ \ / _` |/ _ \| '__/ _` |  _ \ / _ \ \/ /   |
|   |  __/ (_| | | | | (_| | (_) | | | (_| | |_) | (_) >  <    |
|   |_|   \__,_|_| |_|\__,_|\___/|_|  \__,_|____/ \___/_/\_\   |
|                                                              |
|                  Ralink/MTK SDK Plantform                    |
|                    Copyright 2005-2013                       |
|                    Board:HuaWei HG255D                       |
|                                                              |
|                 lintel<lintel.huang@gmail.com>               |
|______________________________________________________________|

===============System Info==================
ASIC 3052_MP2 (Port5<->Phy)
DRAM component: 128 Mbits SDR
DRAM bus: 32 bit
Flash component: NOR Flash
CPU Speed: 384 MHZ
RAM Size:64 Mbytes

Build Date:Jan  7 2014  Time:20:48:20
============================================

GPIO Init:
        UARTF_SHARE_MODE:GPIO
        SPI_GPIO_MODE:GPIO
        I2C_GPIO_MODE:GPIO
GPIO_MODE_REG:0x1f
ReadyLED Bit:0x100

Please choose the operation:
   1: Load system code to SDRAM via TFTP.
   2: Load system code then write to Flash via TFTP.
   3: Boot system code via Flash (default).
   4: Entr boot command line interface.
   7: Load Boot Loader code then write to Flash via Serial.
   9: Load Boot Loader code then write to Flash via TFTP.
0
   
3: System Boot system code via Flash.

Press Reset button enter upgrade mode!
## Booting image at bf080000 ...
   Image Name:   MIPS OpenWrt Linux-2.6.32.59
   Image Type:   MIPS Linux Kernel Image (lzma compressed)
   Data Size:    799632 Bytes = 780.9 kB
   Load Address: 80000000
   Entry Point:  80000000
   Verifying Checksum ... OK
   Uncompressing Kernel Image ... OK
No initrd
## Transferring control to Linux (at address 80000000) ...
## Giving linux memsize in MB, 64

Starting kernel ...

Linux version 2.6.32.59 (work@EmbeddedLab-Server) (gcc version 4.3.3 (GCC) ) #1 Sun Sep 9 00:19:31 CST 2012
bootconsole [early0] enabled
CPU revision is: 0001964c (MIPS 24Kc)
Ralink RT3052 id:1 rev:3 running at 384.00 MHz
Determined physical RAM map:
memory: 04000000 @ 00000000 (usable)
Initrd not found or empty - disabling initrd
Zone PFN ranges:
  Normal   0x00000000 -> 0x00004000
Movable zone start PFN for each node
early_node_map[1] active PFN ranges
    0: 0x00000000 -> 0x00004000
Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 16256
Kernel command line: console=ttyS1,57600 rootfstype=squashfs,jffs2 board=HG255D console=ttyS1,57600 mtdparts=physmap-flash.0:256k(u-boot)ro,128k(u-boot-env)ro,128k(factory)ro,1024k(kernel),14848k(rootfs),15872k@0x80000(firmware),16384k@0x0(fullflash)
PID hash table entries: 256 (order: -2, 1024 bytes)
Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
Primary data cache 16kB, 4-way, VIPT, no aliases, linesize 32 bytes
Writing ErrCtl register=00009506
Readback ErrCtl register=00009506
Memory: 62416k/65536k available (1877k kernel code, 3044k reserved, 339k data, 140k init, 0k highmem)
SLUB: Genslabs=7, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
Hierarchical RCU implementation.
NR_IRQS:48
f`f~fxfxfx怘`f~fxfxfx怘~~xf

请不要胡乱输入以及粘贴、复制等方式灌水

请尊重作者、并共同维护网站的正常阅读，否则账户将会被限制发帖、回帖，站内短信以及阅读权限等都会受到影响，谢谢。 具体限制方式：https://www.right.com.cn/forum/thread-8307840-1-1.html

七里郭

自己顶顶

邪恶海盗

目测固件问题,重刷试试...

七里郭

邪恶海盗 发表于 2014-3-30 21:59
目测固件问题,重刷试试...

后面都是乱码，怎么刷呀

邪恶海盗

七里郭 发表于 2014-3-30 22:54
后面都是乱码，怎么刷呀

选2刷啊。。。

xjingiii

潘多拉盒子，改版Uboot，可以长按侧键，直接使用TFTP刷机。

刷吧！