|
|
* *
* CLoud WiFi Power By Alibaba Group *
* *
****************************************************************
U-Boot 2012.07 [Chaos Calmer 15.05.1,2.0.58-R-20190402.1739] (Apr 02 2019 - 17:39:27)
smem ram ptable found: ver: 1 len: 3
DRAM: 256 MiB
machid : 0x8010001
NAND: ID = 9500f1ef
Vendor = ef
Device = f1
ONFI device found
SF: Detected W25Q32 with page size 4 KiB, total 4 MiB
ipq_spi: page_size: 0x100, sector_size: 0x1000, size: 0x400000
132 MiB
MMC: qca_mmc: 0
In: serial
Out: serial
Err: serial
machid: 8010001
flash_type: 0
Net: MAC0 addr:0:3:7f:ba:db:ad
PHY ID1: 0x4d
PHY ID2: 0xd0b1
ipq40xx_ess_sw_init done
eth0
Loading...
Booting from partition: 1
Creating 1 MTD partitions on "nand0":
0x000000000000-0x000003000000 : "mtd=0"
UBI: attaching mtd2 to ubi0
UBI: physical eraseblock size: 131072 bytes (128 KiB)
UBI: logical eraseblock size: 126976 bytes
UBI: smallest flash I/O unit: 2048
UBI: VID header offset: 2048 (aligned 2048)
UBI: data offset: 4096
UBI: attached mtd2 to ubi0
UBI: MTD device name: "mtd=0"
UBI: MTD device size: 48 MiB
UBI: number of good PEBs: 384
UBI: number of bad PEBs: 0
UBI: max. allowed volumes: 128
UBI: wear-leveling threshold: 4096
UBI: number of internal volumes: 1
UBI: number of user volumes: 3
UBI: available PEBs: 0
UBI: total number of reserved PEBs: 384
UBI: number of PEBs reserved for bad PEB handling: 20
UBI: max/mean erase counter: 5/1
Read 0 bytes from volume kernel to 84000000
No size specified -> Using max size (3428352)
## Booting kernel from FIT Image at 84000000 ...
Using 'config@1' configuration
Trying 'kernel@1' kernel subimage
Description: ARM OpenWrt Linux-3.14.77
Type: Kernel Image
Compression: gzip compressed
Data Start: 0x840000e4
Data Size: 3329436 Bytes = 3.2 MiB
Architecture: ARM
OS: Linux
Load Address: 0x80208000
Entry Point: 0x80208000
Hash algo: crc32
Hash value: 4b662e07
Hash algo: sha1
Hash value: 4737fa8f2770433f6a97b7c302e5b2d665721846
Verifying Hash Integrity ... crc32+ sha1+ OK
## Flattened Device Tree from FIT Image at 84000000
Using 'config@1' configuration
Trying 'fdt@1' FDT blob subimage
Description: ARM OpenWrt qcom-ipq40xx-ap.dkxx device tree blob
Type: Flat Device Tree
Compression: uncompressed
Data Start: 0x8432cfc0
Data Size: 39580 Bytes = 38.7 KiB
Architecture: ARM
Hash algo: crc32
Hash value: 6235377e
Hash algo: sha1
Hash value: 9b87792e7417e8d76f8afe9318f130282177a0e5
Verifying Hash Integrity ... crc32+ sha1+ OK
Booting using the fdt blob at 0x8432cfc0
Uncompressing Kernel Image ... OK
Loading Device Tree to 87062000, end 8706ea9b ... OK
eth0 MAC Address from ART is not valid
eth1 MAC Address from ART is not valid
Using machid 0x8010001 from environment
Starting kernel ...
[ 0.000000] Booting Linux on physical CPU 0x0
[ 0.000000] Linux version 3.14.77 (jenkins@localhost.localdomain) (gcc version 4.8.3 (OpenWrt/Linaro GCC 4.8-2014.04 unknown) ) #1 SMP PREEMPT Tue Apr 2 18:10:57 CST 2019
[ 0.000000] CPU: ARMv7 Processor [410fc075] revision 5 (ARMv7), cr=10c5387d
[ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[ 0.000000] Machine model: Qualcomm Technologies, Inc. IPQ40xx/AP-DK04.1-C1
[ 0.000000] Reserved memory: failed to reserve memory for node 'rsvd1@87000000': base 0x87000000, size 5 MiB
[ 0.000000] Memory policy: Data cache writealloc
[ 0.000000] PERCPU: Embedded 7 pages/cpu @cfbc7000 s7552 r8192 d12928 u32768
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 61696
[ 0.000000] Kernel command line: ubi.mtd=rootfs1 root=mtd:ubi_rootfs rootfstype=squashfs clk_ignore_unused
[ 0.000000] PID hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
[ 0.000000] Memory: 238992K/248832K available (4597K kernel code, 371K rwdata, 1568K rodata, 171K init, 600K bss, 9840K reserved, 0K highmem)
[ 0.000000] Virtual kernel memory layout:
[ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB)
[ 0.000000] fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB)
[ 0.000000] vmalloc : 0xd0800000 - 0xff000000 ( 744 MB)
[ 0.000000] lowmem : 0xc0000000 - 0xd0000000 ( 256 MB)
[ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB)
[ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB)
[ 0.000000] .text : 0xc0208000 - 0xc080d8dc (6167 kB)
[ 0.000000] .init : 0xc080e000 - 0xc0838d80 ( 172 kB)
[ 0.000000] .data : 0xc083a000 - 0xc0896dc8 ( 372 kB)
[ 0.000000] .bss : 0xc0896dc8 - 0xc092d114 ( 601 kB)
[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
[ 0.000000] Preemptible hierarchical RCU implementation.
[ 0.000000] NR_IRQS:16 nr_irqs:16 16
[ 0.000000] Architected cp15 timer(s) running at 48.00MHz (virt).
[ 0.000008] sched_clock: 56 bits at 48MHz, resolution 20ns, wraps every 2863311552512ns
[ 0.000018] Switching to timer-based delay loop
[ 0.000276] Calibrating delay loop (skipped), value calculated using timer frequency.. 96.00 BogoMIPS (lpj=480000)
[ 0.000293] pid_max: default: 32768 minimum: 301
[ 0.001021] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.001037] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.058883] CPU: Testing write buffer coherency: ok
[ 0.059633] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
[ 0.059746] Setting up static identity map for 0x80212220 - 0x80212278
[ 0.141026] CPU1: Booted secondary processor
[ 0.141071] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001
[ 0.160952] CPU2: Booted secondary processor
[ 0.160987] CPU2: thread -1, cpu 2, socket 0, mpidr 80000002
[ 0.181004] CPU3: Booted secondary processor
[ 0.181039] CPU3: thread -1, cpu 3, socket 0, mpidr 80000003
[ 0.181176] Brought up 4 CPUs
[ 0.181218] SMP: Total of 4 processors activated (384.00 BogoMIPS).
[ 0.181227] CPU: All CPU(s) started in SVC mode.
[ 0.220817] VFP support v0.3: implementor 41 architecture 2 part 30 variant 7 rev 5
[ 0.221915] pinctrl core: initialized pinctrl subsystem
[ 0.223341] regulator-dummy: no parameters
[ 0.225995] NET: Registered protocol family 16
[ 0.227577] DMA: preallocated 2048 KiB pool for atomic coherent allocations
[ 0.230036] cpuidle: using governor ladder
[ 0.230052] cpuidle: using governor menu
[ 0.256222]
[ 0.256222] Version Rollback Feature Disabled
[ 0.263419] i2c-msm-v2 78b7000.i2c: probing driver i2c-msm-v2
[ 0.265633] sps:sps is ready.
[ 0.285229] bio: create slab <bio-0> at 0
[ 0.288970] SD0 VccQ: 1800 <--> 3000 mV
[ 0.291975] SCSI subsystem initialized
[ 0.294442] msm_bus_fabric_init_driver
[ 0.294768] msm_bus_device 580000.ad-hoc-bus: Util-fact is missing, default to 100
[ 0.294787] msm_bus_device 580000.ad-hoc-bus: Vrail-comp is missing, default to 100
[ 0.294808] msm_bus_device 580000.ad-hoc-bus: Failed to get bus clk for bus4096 ctx1
[ 0.294865] msm_bus_device 580000.ad-hoc-bus: Util-fact is missing, default to 100
[ 0.294882] msm_bus_device 580000.ad-hoc-bus: Vrail-comp is missing, default to 100
[ 0.294900] msm_bus_device 580000.ad-hoc-bus: Failed to get bus clk for bus1024 ctx1
[ 0.349890] Advanced Linux Sound Architecture Driver Initialized.
[ 0.352671] 80000.qcom,pcie supply vreg-3.3 not found, using dummy regulator
[ 0.352855] 80000.qcom,pcie supply vreg-1.8 not found, using dummy regulator
[ 0.352996] 80000.qcom,pcie supply vreg-0.9 not found, using dummy regulator
[ 0.353128] 80000.qcom,pcie supply gdsc-vdd not found, using dummy regulator
[ 0.353345] msm_pcie_probe: msm_pcie_probe: PCIe: Driver probe failed for RC0:-2
[ 0.353646] msm_pcie: probe of 80000.qcom,pcie failed with error -2
[ 0.353997] Switched to clocksource arch_sys_counter
[ 0.359895] NET: Registered protocol family 2
[ 0.362398] TCP established hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.362462] TCP bind hash table entries: 2048 (order: 2, 16384 bytes)
[ 0.362513] TCP: Hash tables configured (established 2048 bind 2048)
[ 0.362602] TCP: reno registered
[ 0.362619] UDP hash table entries: 256 (order: 1, 8192 bytes)
[ 0.362652] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
[ 0.363468] NET: Registered protocol family 1
[ 0.368819] futex hash table entries: 1024 (order: 4, 65536 bytes)
[ 0.445507] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.445526] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 0.453804] msgmni has been set to 466
[ 0.456406] Key type asymmetric registered
[ 0.456424] Asymmetric key parser 'x509' registered
[ 0.456500] io scheduler noop registered
[ 0.456512] io scheduler deadline registered (default)
[ 0.458296] MDSS QPIC HW Base phy_Address=0x7980000 virt=0xd0b40000
[ 0.458345] mdss_qpic_pinctrl_init: cannot get default pinstate
[ 0.458355] mdss_qpic_pinctrl_init: cannot get sleep pinstate
[ 0.458433] mdss_qpic_panel_io_init: reset gpio not specified
[ 0.458441] mdss_qpic_panel_io_init: cs gpio not specified
[ 0.458450] mdss_qpic_panel_io_init: ad8 gpio not specified
[ 0.458458] mdss_qpic_panel_io_init: te gpio not specified
[ 0.458466] mdss_qpic_panel_io_init: bl gpio not specified
[ 0.458492] 7980000.qcom,msm_qpic supply vdd not found, using dummy regulator
[ 0.458640] 7980000.qcom,msm_qpic supply avdd not found, using dummy regulator
[ 0.458769] msm_bus_cl_get_pdata failed
[ 0.459400] mdss_qpic_panel_probe: Panel Name = qpic lcd panel
[ 0.463150] mdss_fb_register: FrameBuffer[0] 800x480 registered successfully!
[ 0.464876] tcsr 194b000.tcsr: setting usb hs phy mode select = e700e7
[ 0.465075] tcsr 1953000.ess_tcsr: setting ess interface select = 0
[ 0.465265] tcsr 1949000.tcsr: setting wifi_glb_cfg = 41000000
[ 0.465421] tcsr 1957000.tcsr: setting wifi_noc_memtype_m0_m2 = 2222222
[ 0.467118] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
[ 0.470363] msm_serial_hsl_probe: detected port #0 (ttyMSM0)
[ 0.470403] msm_serial_hsl_probe: Bus scaling is disabled
[ 0.470775] 78af000.serial: ttyMSM0 at MMIO 0x78af000 (irq = 139, base_baud = 115200) is a MSM
[ 0.470851] msm_hsl_console_setup: console setup on port #0
[ 1.151702] console [ttyMSM0] enabled
[ 1.156647] msm_serial_hsl_probe: detected port #1 (ttyMSM1)
[ 1.161293] msm_serial_hsl_probe: Bus scaling is disabled
[ 1.167025] 78b0000.serial: ttyMSM1 at MMIO 0x78b0000 (irq = 140, base_baud = 115200) is a MSM
[ 1.176541] msm_serial_hsl_init: driver initialized
[ 1.181033] msm_serial_hs module loaded
[ 1.184813] qca_serial_hs module loaded
[ 1.193150] sps: BAM device 0x07984000 is not registered yet.
[ 1.197937] sps:BAM 0x07984000 is registered.
[ 1.202034] msm_nand_bam_init: msm_nand_bam_init: BAM device registered: bam_handle 0xcedb8240
[ 1.211007] sps:BAM 0x07984000 (va:0xd0a60000) enabled: ver:0x19, number of pipes:7
[ 1.218793] msm_nand_version_check: nand_major:1, nand_minor:4, qpic_major:1, qpic_minor:4
[ 1.227056] msm_nand_flash_onfi_probe: Found an ONFI compliant device W29N01HV ▒
[ 1.235038] msm_nand_scan: NAND Id: 0x9500f1ef Buswidth: 8Bits Density: 128 MByte
[ 1.242484] msm_nand_scan: pagesize: 2048 Erasesize: 131072 oobsize: 64 (in Bytes)
[ 1.250048] msm_nand_scan: BCH ECC: 4 Bit
[ 1.254052] msm_nand_scan: CFG0: 0x2a0408c0, CFG1: 0x0804745c
[ 1.254052] RAWCFG0: 0x280420c0, RAWCFG1: 0x0005045d
[ 1.254052] ECCBUFCFG: 0x00000203, ECCBCHCFG: 0x42040700
[ 1.254052] BAD BLOCK BYTE: 0x000001d1
[ 1.276734] 3 ofpart partitions found on MTD device 7980000.qcom,nand
[ 1.283108] Creating 3 MTD partitions on "7980000.qcom,nand":
[ 1.288877] 0x000000000000-0x000003000000 : "rootfs1"
[ 1.359901] 0x000003000000-0x000006000000 : "rootfs2"
[ 1.429890] 0x000006000000-0x000008000000 : "usrdata"
[ 1.479327] msm_nand_probe: NANDc phys addr 0x7980000, BAM phys addr 0x7984000, BAM IRQ 133
[ 1.486676] msm_nand_probe: Allocated DMA buffer at virt_addr 0xd0a38000, phys_addr 0x8ed9e000
[ 1.497124] sps: BAM device 0x07884000 is not registered yet.
[ 1.501853] sps:BAM 0x07884000 is registered.
[ 1.508614] sps:BAM 0x07884000 (va:0xd0b80000) enabled: ver:0x19, number of pipes:12
[ 1.515830] m25p80 spi0.0: found w25q32, expected n25q128a11
[ 1.521168] m25p80 spi0.0: w25q32 (4096 Kbytes)
[ 1.525734] 13 ofpart partitions found on MTD device spi0.0
[ 1.531205] Creating 13 MTD partitions on "spi0.0":
[ 1.536102] 0x000000000000-0x000000040000 : "0:SBL1"
[ 1.545483] 0x000000040000-0x000000060000 : "0:MIBIB"
[ 1.553726] 0x000000060000-0x0000000c0000 : "0 SEE"
[ 1.561915] 0x0000000c0000-0x0000000d0000 : "0:CDT"
[ 1.569910] 0x0000000d0000-0x0000000e0000 : "0 DRPARAMS"
[ 1.578553] 0x0000000e0000-0x0000000f0000 : "0:APPSBLENV"
[ 1.587118] 0x0000000f0000-0x000000170000 : "0:APPSBL"
[ 1.595360] 0x000000170000-0x000000180000 : "0:ART"
[ 1.603416] 0x000000180000-0x000000190000 : "product_info"
[ 1.612074] 0x000000190000-0x0000001b0000 : "mtdoops"
[ 1.620369] 0x0000001b0000-0x0000001c0000 : "priv_data1"
[ 1.628891] 0x0000001c0000-0x0000001d0000 : "priv_data2"
[ 1.637456] 0x0000001d0000-0x000000200000 : "priv_data3"
[ 1.659101] libphy: ipq40xx_mdio: probed
[ 1.668522] ipq40xx-mdio 90000.mdio: ipq40xx-mdio driver was registered
[ 1.674318] i2c /dev entries driver
[ 1.682337] Load software watchdog success.
[ 1.687338] sdhci: Secure Digital Host Controller Interface driver
[ 1.692484] sdhci: Copyright(c) Pierre Ossman
[ 1.696849] sdhci-pltfm: SDHCI platform and OF driver helper
[ 1.703757] sdhci_msm 7824900.sdhci: Got SD LDO GPIO #33
[ 1.808658] sdhci_msm 7824900.sdhci: Got CD GPIO #22.
[ 1.819094] mmc0: no vmmc regulator found
[ 1.864035] mmc0: SDHCI controller on 7824900.sdhci [7824900.sdhci] using ADMA
[ 1.970288] mmc0: Reset 0x1 never completed.
[ 1.982676] TCP: cubic registered
[ 1.991509] NET: Registered protocol family 10
[ 1.999927] NET: Registered protocol family 17
[ 2.004523] Bridge firewalling registered
[ 2.007505] 8021q: 802.1Q VLAN Support v1.8
[ 2.011925] Registering SWP/SWPB emulation handler
[ 2.019523] regulator-dummy: disabling
[ 2.024149] UBI: attaching mtd0 to ubi0
[ 2.483694] UBI: scanning is finished
[ 2.507806] UBI: attached mtd0 (name "rootfs1", size 48 MiB) to ubi0
[ 2.513129] UBI: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
[ 2.519935] UBI: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
[ 2.526599] UBI: VID header offset: 2048 (aligned 2048), data offset: 4096
[ 2.533438] UBI: good PEBs: 384, bad PEBs: 0, corrupted PEBs: 0
[ 2.539358] UBI: user volume: 3, internal volumes: 1, max. volumes count: 128
[ 2.546478] UBI: max/mean erase counter: 5/1, WL threshold: 4096, image sequence number: 1203369879
[ 2.555502] UBI: available PEBs: 0, total reserved PEBs: 384, PEBs reserved for bad PEB handling: 20
[ 2.564636] UBI: background thread "ubi_bgt0d" started, PID 70
[ 2.574345] drivers/rtc/hctosys.c: unable to open rtc device (rtc0)
[ 2.589282] clk: Not disabling unused clocks
[ 2.592519] ALSA device list:
[ 2.595514] No soundcards found.
[ 2.620785] VFS: Mounted root (squashfs filesystem) readonly on device 31:17.
[ 2.627272] Freeing unused kernel memory: 168K (c080e000 - c0838000)
[ 4.037277] init: Console is alive
[ 4.040104] init: - watchdog -
[ 8.699853] usbcore: registered new interface driver usbfs
[ 8.704786] usbcore: registered new interface driver hub
[ 8.710109] usbcore: registered new device driver usb
[ 8.719115] Button Hotplug driver version 0.4.1
[ 8.735244] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 8.742560] ehci-platform: EHCI generic platform driver
[ 9.459584] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller
[ 9.464237] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 1
[ 9.473440] xhci-hcd xhci-hcd.0.auto: irq 164, io mem 0x08a00000
[ 9.481363] hub 1-0:1.0: USB hub found
[ 9.484216] hub 1-0:1.0: 1 port detected
[ 9.489441] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller
[ 9.493951] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 2
[ 9.504593] hub 2-0:1.0: USB hub found
[ 9.507419] hub 2-0:1.0: 1 port detected
[ 9.512848] xhci-hcd xhci-hcd.1.auto: xHCI Host Controller
[ 9.517405] xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 3
[ 9.526699] xhci-hcd xhci-hcd.1.auto: irq 168, io mem 0x06000000
[ 9.534524] hub 3-0:1.0: USB hub found
[ 9.537347] hub 3-0:1.0: 1 port detected
[ 9.542617] xhci-hcd xhci-hcd.1.auto: xHCI Host Controller
[ 9.547136] xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 4
[ 9.557745] hub 4-0:1.0: USB hub found
[ 9.560559] hub 4-0:1.0: config failed, hub doesn't have any ports! (err -19)
[ 9.576588] usbcore: registered new interface driver usb-storage
[ 10.044869] init: - preinit -
Before mount_root
[ 10.530455] UBIFS: background thread "ubifs_bgt0_2" started, PID 81
[ 10.531934] random: procd: uninitialized urandom read (4 bytes read, 81 bits of entropy available)
[ 10.595251] UBIFS: recovery needed
[ 10.755234] UBIFS: recovery completed
[ 10.758065] UBIFS: mounted UBI device 0, volume 2, name "rootfs_data"
[ 10.764321] UBIFS: LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
[ 10.773411] UBIFS: FS size: 24633344 bytes (23 MiB, 194 LEBs), journal size 1269760 bytes (1 MiB, 10 LEBs)
[ 10.783056] UBIFS: reserved for root: 1163493 bytes (1136 KiB)
[ 10.788878] UBIFS: media format: w4/r0 (latest is w4/r0), UUID B7F1A276-30E0-463B-B3B3-84B2D1413F9E, small LPT model
[ 10.806064] mount_root: switching to jffs2 overlay
After mount_root
[ 11.058511] procd: - early -
[ 11.060559] procd: - watchdog -
[ 11.864596] procd: - ubus -
[ 12.868886] random: ubusd: uninitialized urandom read (4 bytes read, 112 bits of entropy available)
[ 12.877530] random: ubusd: uninitialized urandom read (4 bytes read, 112 bits of entropy available)
[ 12.886024] random: ubusd: uninitialized urandom read (4 bytes read, 112 bits of entropy available)
[ 12.896062] random: ubusd: uninitialized urandom read (4 bytes read, 112 bits of entropy available)
[ 12.904145] random: ubusd: uninitialized urandom read (4 bytes read, 112 bits of entropy available)
[ 12.913394] random: ubusd: uninitialized urandom read (4 bytes read, 112 bits of entropy available)
[ 12.922441] random: ubusd: uninitialized urandom read (4 bytes read, 112 bits of entropy available)
[ 12.931749] procd: - init -
Please press Enter to activate this console.
[ 16.328693] QCE50: __qce_init_clk: Unable to get CE core src clk, set to NULL
[ 16.334927] qcrypto 8e20000.qcrypto: Qualcomm Crypto 5.3.1 device found @0x8e20000
[ 16.342362] qcrypto 8e20000.qcrypto: CE device = 0x0
[ 16.342362] , IO base, CE = 0xd16c0000
[ 16.342362] , Consumer (IN) PIPE 2, Producer (OUT) PIPE 3
[ 16.342362] IO base BAM = 0x (null)
[ 16.342362] BAM IRQ 239
[ 16.342362] Engines Availability = 0x2010453
[ 16.367150] QCE50: qce_sps_get_bam: qce50 don't support command descriptor. bam_cfg0
[ 16.374699] sps:BAM 0x08e04000 is registered.
[ 16.379839] sps:BAM 0x08e04000 (va:0xd1700000) enabled: ver:0x27, number of pipes:4
[ 16.387720] QCE50: qce_sps_init: Qualcomm MSM CE-BAM at 0x0000000008e04000 irq 239
[ 16.394464] bus_scale_table is NULL
[ 16.398084] qcrypto 8e20000.qcrypto: qcrypto-ecb-aes
[ 16.402956] qcrypto 8e20000.qcrypto: qcrypto-cbc-aes
[ 16.407925] qcrypto 8e20000.qcrypto: qcrypto-ctr-aes
[ 16.412830] qcrypto 8e20000.qcrypto: qcrypto-ecb-des
[ 16.417805] qcrypto 8e20000.qcrypto: qcrypto-cbc-des
[ 16.422724] qcrypto 8e20000.qcrypto: qcrypto-ecb-3des
[ 16.427806] qcrypto 8e20000.qcrypto: qcrypto-cbc-3des
[ 16.432799] qcrypto 8e20000.qcrypto: qcrypto-xts-aes
[ 16.437765] qcrypto 8e20000.qcrypto: qcrypto-sha1
[ 16.442429] qcrypto 8e20000.qcrypto: qcrypto-sha256
[ 16.447313] qcrypto 8e20000.qcrypto: qcrypto-aead-hmac-sha1-cbc-aes
[ 16.453536] qcrypto 8e20000.qcrypto: qcrypto-aead-hmac-sha1-cbc-des
[ 16.459815] qcrypto 8e20000.qcrypto: qcrypto-aead-hmac-sha1-cbc-3des
[ 16.466200] qcrypto 8e20000.qcrypto: qcrypto-aead-hmac-sha256-cbc-aes
[ 16.472552] qcrypto 8e20000.qcrypto: qcrypto-aead-hmac-sha256-cbc-des
[ 16.479003] qcrypto 8e20000.qcrypto: qcrypto-aead-hmac-sha256-cbc-3des
[ 16.485512] qcrypto 8e20000.qcrypto: qcrypto-hmac-sha1
[ 16.490609] qcrypto 8e20000.qcrypto: qcrypto-hmac-sha256
[ 16.495929] qcrypto 8e20000.qcrypto: qcrypto-aes-ccm
[ 16.500850] qcrypto 8e20000.qcrypto: qcrypto-rfc4309-aes-ccm
[ 16.506340] qcrypto: FIPS140-2 Known Answer Tests: Skipped
[ 16.540136] mtdoops: Attached to MTD device 12
[ 16.547566] ramoops: using module parameters
[ 16.554563] console [pstore-1] enabled
[ 16.557289] pstore: Registered ramoops as persistent store backend
[ 16.563456] ramoops: attached 0x200000@0x8fe00000, ecc: 0/0
[ 16.580736] nf_conntrack version 0.5.0 (3736 buckets, 14944 max)
[ 16.592785] Key type dns_resolver registered
[ 16.599364] NTFS driver 2.1.30 [Flags: R/O MODULE].
[ 16.620763] Initializing XFRM netlink socket
[ 16.626468] NET: Registered protocol family 15
[ 16.651479] loop: module loaded
[ 16.658667] PPP generic driver version 2.4.2
[ 16.693282] random: nonblocking pool is initialized
[ 17.147514] ess-switch DT exist!
[ 17.149740] switchreg_base_addr: 0xc000000
[ 17.153796] switchreg_size: 0x80000
[ 17.157316] switch_access_mode: local bus
[ 17.161265] mac mode = 0x0
[ 17.163952] mac mode1 doesn't exit!
[ 17.167445] mac mode2 doesn't exit!
[ 17.170923] ess-uniphy DT doesn't exist!
[ 17.174827] wan bmp:0x20
[ 17.177335] ess-psgmii DT exist!
[ 17.180554] current dts led_source_num is 5
[ 17.184733] mdio DT exist!
[ 17.187394] ssdk_plat_init start
[ 17.190836] enable ess clk
[ 17.303834] reset ok in probe!
[ 17.306732] PHY ID is 0x4dd0b1
[ 17.369859] qca probe malibu phy driver succeeded!
[ 19.175082] Chip version 0x1401
[ 19.177252] qca-ssdk module init succeeded!
[ 19.193297] **********************************************************
[ 19.198896] * Driver :NSS GMAC Driver for RTL v(3.72a)
[ 19.204239] * Version :1.0
[ 19.207045] * Copyright :Copyright (c) 2013-2016 The Linux Foundation. All rights reserved.
[ 19.215429] **********************************************************
[ 19.264207] l2tp_core: L2TP core driver, V2.0
[ 19.269901] l2tp_netlink: L2TP netlink interface
[ 19.289227] qca-nss-drv.ko is loaded for symbol link
[ 19.296479] sit: IPv6 over IPv4 tunneling driver
[ 19.307664] nat46: module (version 8ff2ae59ec9840a7b8b45f976c51cae80abe0226) loaded.
[ 19.355916] gre: GRE over IPv4 demultiplexor driver
[ 19.362352] ip_gre: GRE over IPv4 tunneling driver
[ 19.380417] bonding: Ethernet Channel Bonding Driver: v3.7.1 (April 27, 2011)
[ 19.415597] QCA multicast snooping installed successfully
[ 19.426455] ip6_tables: (C) 2000-2006 Netfilter Core Team
[ 19.448267] EDMA using MAC@ - using
[ 19.450568] ee:ee:52:a7:eb:6f
[ 19.458440] register dev[eth0] with mtu[1500]
[ 19.462511] EDMA using MAC@ - using
[ 19.465330] 0a:00:82:23:8b:f1
[ 19.474671] register dev[eth1] with mtu[1500]
[ 19.566403] IMQ driver loaded successfully. (numdevs = 2, numqueues = 1)
[ 19.572085] Hooking IMQ before NAT on PREROUTING.
[ 19.576916] Hooking IMQ after NAT on POSTROUTING.
[ 19.607331] QCA Hy-Fi multicast installation successfully
[ 19.626698] nss_lag_init[345] AG Manager Installed
[ 19.636410] NET: Registered protocol family 24
[ 19.642439] PPTP driver version 0.8.5
[ 19.652147] <NSS-CRYPTO>:module loaded (platform - IPQ806x, build - Build_ID - 04/02/19, 17:46:42)
[ 19.664252] <NSS-CRYPTO>:qca-nss-crypto.ko is loaded for symbol link
[ 19.673695] crypto bench loaded - Build_ID - 04/02/19, 17:46:48
[ 19.678978] nss_crypto_register_user[151]:bf5e2134: Crypto Device is not ready
[ 19.689632] nss_macsec init success
[ 19.699820] nss is not enabled on this platform
[ 19.703346] nss_ipsecmgr_init[977]:NSS is not enabled in this platform
[ 19.717272] nss_crypto_register_user[151]:bf5e2134: Crypto Device is not ready
[ 19.726045] nss_crypto_register_user[151]:bf5e2134: Crypto Device is not ready
[ 19.753806] u32 classifier
|
|
/1 
IP卡
狗仔卡
发表于 2022-8-12 14:35
置顶卡
沉默卡
喧嚣卡
顶贴卡
显身卡