|
原来进miniweb刷固件后路由一直起不来就借了TTL线然后找了教程来刷
差不多是先输入命令e a,然后再进入miniweb传入固件,最后输入命令 i 清除配置还有r运行系统
刷了几遍都是最后都是卡在一个unable to read inode
这几天拿起来又重新刷了一下发现卡住的地方又不一样了
CFE> e a
Erase all flash (except bootrom)? (y/n):y
................................................................................ ...............................................
Resetting board...Boot Address 0xbe000000
Initializing Arena.
Initializing Devices.
Parallel flash device: name AM29LV320MT|S29GL128-A, id 0x2201, size 16384KB
Flash Layout: Boot[0,0xbe000000] Kern[1,0xbe020000]
AuxFS[93,0xbeba0000] Misc[125,0xbefa0000] PSI[127,0xbefe0000]
Flash RootFS Partition Length: 12058624
CPU type 0x2A010: 300MHz, Bus: 133MHz, Ref: 64MHz
CPU running TP0
Total memory: 33554432 bytes (32MB)
Total memory used by CFE: 0x80401000 - 0x80529860 (1214560)
Initialized Data: 0x8041E740 - 0x80421060 (10528)
** Flash image not found. **
Board IP address : 192.168.1.1:ffffff00
Host IP address : 192.168.1.100
Gateway IP address :
Run from flash/host (f/h) : f
Default host run file name : vmlinux
Default host flash file name : bcm963xx_fs_kernel
Boot delay (0-9 seconds) : 1
Board Id (0-8) : 96358VW2
Number of MAC Addresses (1-32) : 11
Base MAC Address : 00:1f:a3:1e:ef:f4
PSI Size (1-64) KBytes : 24
Flash Block Size (1-128) in KBytes: 128
Auxillary File System Size Percent: 25
Main Thread Number [0|1] : 0
udp_send finished
No answer .auto boot ...
web info: Upload 2752516 bytes, Broadcom image format.
CFE>
Flashing root file system and kernel at 0xbe020000: ......................
.
*** Image flash done *** !
Resetting board...Boot Address 0xbe000000
Initializing Arena.
Initializing Devices.
Parallel flash device: name AM29LV320MT|S29GL128-A, id 0x2201, size 16384KB
Flash Layout: Boot[0,0xbe000000] Kern[1,0xbe020000]
AuxFS[93,0xbeba0000] Misc[125,0xbefa0000] PSI[127,0xbefe0000]
Flash RootFS Partition Length: 12058624
CPU type 0x2A010: 300MHz, Bus: 133MHz, Ref: 64MHz
CPU running TP0
Total memory: 33554432 bytes (32MB)
Total memory used by CFE: 0x80401000 - 0x80529860 (1214560)
Initialized Data: 0x8041E740 - 0x80421060 (10528)
Board IP address : 192.168.1.1:ffffff00
Host IP address : 192.168.1.100
Gateway IP address :
Run from flash/host (f/h) : f
Default host run file name : vmlinux
Default host flash file name : bcm963xx_fs_kernel
Boot delay (0-9 seconds) : 1
Board Id (0-8) : 96358VW2
Number of MAC Addresses (1-32) : 11
Base MAC Address : 00:1f:a3:1e:ef:f4
PSI Size (1-64) KBytes : 24
Flash Block Size (1-128) in KBytes: 128
Auxillary File System Size Percent: 25
Main Thread Number [0|1] : 0
udp_send finished
No answer .auto boot ...
*** Press any key to stop auto run (1 seconds) ***
Auto run second count down: 0
Code Address: 0x80010000, Entry Address: 0x80010000
Decompression OK!
Entry at 0x80010000
Closing network.
Starting program at 0x80010000
Linux version 2.6.32.27 (jow@nd-build-02.linux-appliance.net) (gcc version 4.3.3 (GCC) ) #5 Wed Dec 21 05:51:40 CET 2011
Detected Broadcom 0x6358 CPU revision a1
CPU frequency is 300 MHz
32MB of RAM installed
registering 40 GPIOs
board_bcm963xx: CFE version: 1.0.37-10.3
bootconsole [early0] enabled
CPU revision is: 0002a010 (Broadcom BCM6358)
board_bcm963xx: board name: 96358VW2
Determined physical RAM map:
memory: 02000000 @ 00000000 (usable)
Initrd not found or empty - disabling initrd
Zone PFN ranges:
Normal 0x00000000 -> 0x00002000
Movable zone start PFN for each node
early_node_map[1] active PFN ranges
0: 0x00000000 -> 0x00002000
Built 1 zonelists in Zone order, mobility grouping on. Total pages: 8128
Kernel command line: root=/dev/mtdblock2 rootfstype=squashfs,jffs2 noinitrd cons ole=ttyS0,115200
PID hash table entries: 128 (order: -3, 512 bytes)
Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)
Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)
Primary instruction cache 32kB, VIPT, 2-way, linesize 16 bytes.
Primary data cache 16kB, 2-way, VIPT, cache aliases, linesize 16 bytes
Memory: 29528k/32768k available (2140k kernel code, 3240k reserved, 453k data, 1 40k init, 0k highmem)
Hierarchical RCU implementation.
NR_IRQS:128
Calibrating delay loop... 299.00 BogoMIPS (lpj=598016)
Mount-cache hash table entries: 512
NET: Registered protocol family 16
registering PCI controller with io_map_base unset
registering PCI controller with io_map_base unset
bio: create slab <bio-0> at 0
pci 0000:01:1e.0: CardBus bridge, secondary bus 0000:02
pci 0000:01:1e.0: IO window: 0x8008000-0x80080ff
pci 0000:01:1e.0: IO window: 0x8008400-0x80084ff
pci 0000:01:1e.0: MEM window: 0x38000000-0x3fffffff
PCI: Enabling device 0000:01:1e.0 (0000 -> 0003)
Switching to clocksource MIPS
PCI: Enabling device 0000:00:01.0 (0000 -> 0002)
Kernel bug detected[#1]:
Cpu 0
$ 0 : 00000000 10008400 00000001 80026cf4
$ 4 : 802c1000 802d0000 802cd340 fefed000
$ 8 : 00000000 800141b0 00000000 00000002
$12 : 00000018 00000000 00000000 6e637920
$16 : 00002000 c0000000 c0000000 00000400
$20 : 8018f73c 802c1c00 30000000 c0002000
$24 : 00000000 80190574
$28 : 81814000 81815be0 00000000 80025454
Hi : 00000000
Lo : 00000000
epc : 80025464 0x80025464
Not tainted
ra : 80025454 0x80025454
Status: 10008403 KERNEL EXL IE
Cause : 00800034
PrId : 0002a010 (Broadcom BCM6358)
Modules linked in:
Process swapper (pid: 1, threadinfo=81814000, task=81813938, tls=00000000)
Stack : fffedb3b 10008401 00000001 8185531c 8018f73c 70000000 00000000 00000000
00000000 00000000 81855000 00000000 8018f73c 00000000 00000000 00000000
00000000 8013cfd8 00000002 00000000 00000034 8013f4b8 81815c40 8003a9d0
00000000 8018e6c8 00000000 81855000 81855000 8018fdfc 802c7c5c 00000000
00000000 00000000 81855000 8185531c 8018f73c 00000000 00000000 00000000
...
Call Trace:[<8018f73c>] 0x8018f73c
[<8018f73c>] 0x8018f73c
[<8013cfd8>] 0x8013cfd8
[<8013f4b8>] 0x8013f4b8
[<8003a9d0>] 0x8003a9d0
[<8018e6c8>] 0x8018e6c8
[<8018fdfc>] 0x8018fdfc
[<8018f73c>] 0x8018f73c
[<8018ddcc>] 0x8018ddcc
[<80030470>] 0x80030470
[<80190574>] 0x80190574
[<8013f4b8>] 0x8013f4b8
[<80192ef8>] 0x80192ef8
[<8013f2e4>] 0x8013f2e4
[<80192ef8>] 0x80192ef8
[<8013f424>] 0x8013f424
[<8018e000>] 0x8018e000
[<801905f0>] 0x801905f0
[<80146080>] 0x80146080
[<801460f8>] 0x801460f8
[<801630e4>] 0x801630e4
[<80163258>] 0x80163258
[<8012b39c>] 0x8012b39c
[<8016339c>] 0x8016339c
[<8012ba78>] 0x8012ba78
[<80163330>] 0x80163330
[<8016299c>] 0x8016299c
[<8012bb08>] 0x8012bb08
[<800e46ac>] 0x800e46ac
[<80162118>] 0x80162118
[<800e3d08>] 0x800e3d08
[<8012b39c>] 0x8012b39c
[<8012b650>] 0x8012b650
[<8016374c>] 0x8016374c
[<80162bb0>] 0x80162bb0
[<80146384>] 0x80146384
[<802a8f6c>] 0x802a8f6c
[<802a8f6c>] 0x802a8f6c
[<802a8ff4>] 0x802a8ff4
[<802a763c>] 0x802a763c
[<8001bc68>] 0x8001bc68
[<800661dc>] 0x800661dc
[<802a86d0>] 0x802a86d0
[<8029933c>] 0x8029933c
[<8001e6c8>] 0x8001e6c8
[<8029926c>] 0x8029926c
[<8001e6b8>] 0x8001e6b8
Code: afb10014 38420001 02408821 <00028036> 367301df 3c1e0040 afb30018 12a0 005d 3c02003f
Disabling lock debugging due to kernel taint
Kernel panic - not syncing: Attempted to kill init!
把所有出来的log都贴出来了..那个unable to read inode好像是flash的问题..但是不知道怎么解决,现在卡住的提示又变了..完全没有头绪了
希望知道这个问题的大神能给指点指点 |
|