MERCURY（水晶） MAC1200R TTL 刷机，串口发送tpl 没有反应，现金求助！

baiho***

MERCURY（水晶） MAC1200R TTL 刷机，串口发送tpl 没有反应，现金求助！
各位高手，大家好，
我最近买了一款 MERCURY（水晶） MAC1200R，想刷入 openwrt 系统，按照网上的一些教程操作，
putty，sscom32等上也打印出路由器的启动信息了，但是在出现 Autobooting in 1 seconds 的时候，通过sscom32 发送 tpl，却没有阻断路由器

而且我发现，这个MERCURY（水晶） MAC1200R 启动的串口信息代码，和网上教程都不太一样
稍后我会附上截图

说明：
1  这个型号的路由器访问的ip是192.168.0.1，网上的教程基本上都是192.168.1.1
2  路由器启动之后，我在串口端发送 tpl，后，会出现  SLP login： 的信息
3  我以前用db120安装过openwrt，但当时没有用 TTL 的方式安装

谢谢大家，如果有好心的高手，请联系我，qq： 815227970  
我会通过支付宝等手段 打现金 感谢你的帮助！

zdg***

这个就是TPL    家电就快速 TPL  ,我改了几个都是这样

baiho***

谢谢楼上的回答！

hackp***

新买的？很不幸已经不是AR9344+QCA9882的了。
变成MTK的CPU，操作方法应该不一样

baiho***

我刚才又操作了一番，

一开机就来输入这个 tpl，但是也许是我又操作错误吧，现在还是有一些问题

我的路由器启动的信息如下：
U-Boot 1.1.3 (Feb 28 2015 - 13:41:15)


Board: Ralink APSoC DRAM:  64 MB

relocate_code Pointer at: 83fc0000

flash manufacture id: ef, device id 40 17

find flash: W25Q64BV

*** Warning - bad CRC, using default environment



Now booting Linux!


Autobooting in 1 seconds

## Booting image at bc040000 ...

---- tpHdr = bc040000

---- text base = 80000000

---- entry point = 80000000

   Uncompressing Kernel Image ... OK

No initrd

## Transferring control to Linux (at address 80000000) ...

## Giving linux memsize in MB, 64


Starting kernel ...

LINUX started...

THIS IS ASIC
[    0.000000] Linux version 3.10.14 (tplink@tplink-0B) (gcc version 4.6.3 20120201 (prerelease) (Linaro GCC 4.6-2012.02) ) #1 Sat Feb 28 13:51:39 CST 2015
[    0.000000]
[    0.000000]  The CPU feqenuce set to 575 MHz
[    0.000000] CPU0 revision is: 00019655 (MIPS 24KEc)
[    0.000000] Software DMA cache coherency
[    0.000000] Determined physical RAM map:
[    0.000000]  memory: 04000000 @ 00000000 (usable)
[    0.000000] Initrd not found or empty - disabling initrd
[    0.000000] Zone ranges:
[    0.000000]   Normal   [mem 0x00000000-0x03ffffff]
[    0.000000] Movable zone start for each node
[    0.000000] Early memory node ranges
[    0.000000]   node   0: [mem 0x00000000-0x03ffffff]
[    0.000000] Primary instruction cache 64kB, 4-way, VIPT, linesize 32 bytes.
[    0.000000] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 16256
[    0.000000] Kernel command line: console=ttyS1,57600n8 root=/dev/mtdblock6 rootfstype=squashfs,jffs2 noinitrd rootfstype=squashfs,jffs2
[    0.000000] PID hash table entries: 256 (order: -2, 1024 bytes)
[    0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
[    0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
[    0.000000] Writing ErrCtl register=0002ea5a
[    0.000000] Readback ErrCtl register=0002ea5a
[    0.000000] Memory: 61088k/65536k available (2770k kernel code, 4448k reserved, 647k data, 164k init, 0k highmem)
[    0.000000] NR_IRQS:128
[    0.000000] console [ttyS1] enabled
[    0.096000] Calibrating delay loop... 382.46 BogoMIPS (lpj=764928)
[    0.128000] pid_max: default: 32768 minimum: 301
[    0.132000] Mount-cache hash table entries: 512
[    0.136000] NET: Registered protocol family 16
[    0.140000] RALINK_GPIOMODE = 54054404
[    0.144000] RALINK_GPIOMODE = 54044404
[    0.244000] ***** Xtal 40MHz *****
[    0.248000] start PCIe register access
[    0.748000] RALINK_RSTCTRL = 2400000
[    0.752000] RALINK_CLKCFG1 = fdbfffc0
[    0.756000]
[    0.756000] *************** MT7628 PCIe RC mode *************
[    1.256000] PCIE0 enabled
[    1.260000] Port 0 N_FTS = 1b105000
[    1.264000] init_rt2880pci done
[    1.288000] bio: create slab <bio-0> at 0
[    1.292000] PCI host bridge to bus 0000:00
[    1.296000] pci_bus 0000:00: root bus resource [mem 0x20000000-0x2fffffff]
[    1.300000] pci_bus 0000:00: root bus resource [io  0x10160000-0x1016ffff]
[    1.304000] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]
[    1.308000] pci 0000:00:00.0: BAR 0: can't assign mem (size 0x80000000)
[    1.312000] pci 0000:00:00.0: BAR 8: assigned [mem 0x20000000-0x200fffff]
[    1.316000] pci 0000:00:00.0: BAR 9: assigned [mem 0x20100000-0x201fffff pref]
[    1.320000] pci 0000:00:00.0: BAR 1: assigned [mem 0x20200000-0x2020ffff]
[    1.324000] pci 0000:01:00.0: BAR 0: assigned [mem 0x20000000-0x200fffff 64bit]
[    1.328000] pci 0000:01:00.0: BAR 6: assigned [mem 0x20100000-0x2010ffff pref]
[    1.332000] pci 0000:00:00.0: PCI bridge to [bus 01]
[    1.336000] pci 0000:00:00.0:   bridge window [mem 0x20000000-0x200fffff]
[    1.340000] pci 0000:00:00.0:   bridge window [mem 0x20100000-0x201fffff pref]
[    1.344000] BAR0 at slot 0 = 0
[    1.348000] bus=0x0, slot = 0x0
[    1.352000] res[0]->start = 0
[    1.356000] res[0]->end = 0
[    1.360000] res[1]->start = 20200000
[    1.364000] res[1]->end = 2020ffff
[    1.368000] res[2]->start = 0
[    1.372000] res[2]->end = 0
[    1.376000] res[3]->start = 0
[    1.380000] res[3]->end = 0
[    1.384000] res[4]->start = 0
[    1.388000] res[4]->end = 0
[    1.392000] res[5]->start = 0
[    1.396000] res[5]->end = 0
[    1.400000] bus=0x1, slot = 0x0
[    1.404000] res[0]->start = 20000000
[    1.408000] res[0]->end = 200fffff
[    1.412000] res[1]->start = 0
[    1.416000] res[1]->end = 0
[    1.420000] res[2]->start = 0
[    1.424000] res[2]->end = 0
[    1.428000] res[3]->start = 0
[    1.432000] res[3]->end = 0
[    1.436000] res[4]->start = 0
[    1.440000] res[4]->end = 0
[    1.444000] res[5]->start = 0
[    1.448000] res[5]->end = 0
[    1.452000] cfg80211: Calling CRDA to update world regulatory domain
[    1.456000] Switching to clocksource MIPS
[    1.460000] NET: Registered protocol family 2
[    1.472000] TCP established hash table entries: 512 (order: 0, 4096 bytes)
[    1.484000] TCP bind hash table entries: 512 (order: -1, 2048 bytes)
[    1.496000] TCP: Hash tables configured (established 512 bind 512)
[    1.508000] TCP: reno registered
[    1.516000] UDP hash table entries: 256 (order: 0, 4096 bytes)
[    1.528000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[    1.540000] NET: Registered protocol family 1
[    1.552000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    1.564000] jffs2: version 2.2. (NAND) (SUMMARY)  (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[    1.584000] msgmni has been set to 119
[    1.592000] io scheduler noop registered (default)
[    1.612000] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
[    1.624000] serial8250: ttyS0 at MMIO 0x10000d00 (irq = 21) is a 16550A
[    1.636000] serial8250: ttyS1 at MMIO 0x10000c00 (irq = 20) is a 16550A
[    1.652000] Ralink gpio driver initialized
[    1.660000] flash manufacture id: ef, device id 40 17
[    1.672000] W25Q64BV(ef 40170000) (8192 Kbytes)
[    1.680000] mtd .name = raspi, .size = 0x00800000 (8M) .erasesize = 0x00010000 (64K) .numeraseregions = 0
[    1.700000] Searching for RedBoot partition table
[    1.708000] 8 RedBoot partitions found on MTD device raspi
[    1.720000] Creating 8 MTD partitions on "raspi":
[    1.728000] 0x000000000000-0x00000001d800 : "factory_boot"
[    1.740000] mtd: partition "factory_boot" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
[    1.768000] 0x00000001d800-0x00000001e000 : "factory_info"
[    1.780000] 0x00000001e000-0x000000020000 : "art"
[    1.792000] 0x000000020000-0x000000030000 : "config"
[    1.804000] 0x000000030000-0x000000040000 : "boot"
[    1.812000] 0x000000040000-0x000000171864 : "kernel"
[    1.824000] mtd: partition "kernel" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
[    1.848000] 0x000000171864-0x000000800000 : "rootfs"
[    1.860000] mtd: partition "rootfs" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
[    1.888000] mtd: device 6 (rootfs) set to be root filesystem
[    1.896000] mtd: partition "rootfs_data" created automatically, ofs=0x4c0000, len=0x340000
[    1.916000] 0x0000004c0000-0x000000800000 : "rootfs_data"
[    1.928000] 0x000000040000-0x000000800000 : "firmware"
[    1.940000] rdm_major = 253
[    1.944000] netif_napi_add() called with weight 128 on device eth0
[    1.956000] GMAC1_MAC_ADRH -- : 0x0000000c
[    1.964000] GMAC1_MAC_ADRL -- : 0x4328803f
[    1.972000] Ralink APSoC Ethernet Driver Initilization. v3.1  512 rx/tx descriptors allocated, mtu = 1500!
[    1.992000] NAPI enable, Tx Ring = 512, Rx Ring = 512
[    2.004000] GMAC1_MAC_ADRH -- : 0x0000000c
[    2.012000] GMAC1_MAC_ADRL -- : 0x4328802a
[    2.020000] PROC INIT OK!
[    2.024000] u32 classifier
[    2.032000]     Performance counters on
[    2.040000]     input device check on
[    2.044000]     Actions configured
[    2.052000] TCP: cubic registered
[    2.060000] NET: Registered protocol family 10
[    2.068000] NET: Registered protocol family 17
[    2.080000] 8021q: 802.1Q VLAN Support v1.8
[    2.088000] registered taskstats version 1
[    2.100000] Registered character driver slp_flash_chrdev
[    2.116000] VFS: Mounted root (squashfs filesystem) readonly on device 31:6.
[    2.132000] Freeing unused kernel memory: 164K (80357000 - 80380000)
OK

No initrd

## Transferring control to Linux (at address 80000000) ...

## Giving linux memsize in MB, 64


Starting kernel ...

LINUX started...

==================================

不知道是因为什么？ 请赐教！
另外我本身是学习软件出身的，做个网站 ，还有app之类的，能力还可以，不知道能不能帮上各位什么忙的

龍***

baihongjian 发表于 2015-8-8 23:36
我刚才又操作了一番，

一开机就来输入这个 tpl，但是也许是我又操作错误吧，现在还是有一些问题

我最近也入手了这个路由器，貌似被坑了：MTK的解决方案！

目前没有能用的不死Uboot（Breed），没有能用的固件。我手头有编程器，试着刷了几个Breed都不能正常使用（高通方案的uboot直接挂掉，MT7628和极路由 极壹S (HC5661A) 专用版本这两个的Breed一直进Breed界面）。

如果你想折腾，也可以买一个编程器（CH341A，淘宝一大堆）试试。

如有进展，可以交流一下！

jxb***

有进展没有？

jxb***

我试过了，通电输入slp即可进入，tpl无效的

haa***

这个V2.0的有新的固件可以刷的吗？

xhu***

我就看看，赚点钱

zly5***

jxbking 发表于 2016-1-3 17:52
我试过了，通电输入slp即可进入，tpl无效的

今天试了TTL连接，开机输入SLP的确有效，不再进入登录了。但后续breed不敢刷入，怕变砖

jijiw***

楼主之后解决了吗？怎么解决的可以说一下么？

zly5***

同问：出现 SLP login，不知道账号密码

lyh***

要在出现 Autobooting in 1 seconds 时快速输入slp（最好先复制到粘贴板，然后直接快速粘贴），否则会出现slp login.