MW4530原版固件的ttl启动信息

savi***

很经典的。


U-Boot 1.1.4 (Apr 26 2012 - 08:18:48)

U-boot DB120


DRAM:  128 MB
id read 0x100000ff
flash size 8MB, sector count = 128
Flash:  8 MB
Using default environment

In:    serial
Out:   serial
Err:   serial
Net:   ag934x_enet_initialize...
No valid address in Flash. Using fixed address
wasp  reset mask:c03300
WASP  ----> S17 PHY *
: cfg1 0x7 cfg2 0x7114
eth0: ba:be:fa:ce:08:41
athrs17_reg_init: complete
eth0 up
eth0
Autobooting in 1 seconds
## Booting image at 9f020000 ...
   Uncompressing Kernel Image ... OK

Starting kernel ...

Booting Atheros AR934x

Linux version 2.6.31--LSDK-9.2.0_U6.616 (root@localhost.localdomain) (gcc version 4.3.3 (GCC) ) #1 Thu Apr 26 08:21:33 PDT 2012
Ram size passed from bootloader =128M
flash_size passed from bootloader = 8
CPU revision is: 0001974c (MIPS 74Kc)
ath_sys_frequency: cpu srif ddr srif cpu 560 ddr 450 ahb 225
Determined physical RAM map:
memory: 08000000 @ 00000000 (usable)
Zone PFN ranges:
  Normal   0x00000000 -> 0x00008000
Movable zone start PFN for each node
early_node_map[1] active PFN ranges
    0: 0x00000000 -> 0x00008000
Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 32512
Kernel command line: console=ttyS0,115200 root=31:02 rootfstype=squashfs init=/sbin/init mtdparts=ath-nor0:128k(u-boot),1024k(kernel),6912k(rootfs),64k(config),64k(ART) mem=128M
PID hash table entries: 512 (order: 9, 2048 bytes)
Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
Writing ErrCtl register=00000000
Readback ErrCtl register=00000000
Memory: 113180k/131072k available (1637k kernel code, 17728k reserved, 399k data, 112k init, 0k highmem)
NR_IRQS:128
plat_time_init: plat time init done
Calibrating delay loop... 279.55 BogoMIPS (lpj=559104)
Mount-cache hash table entries: 512

****************ALLOC***********************
Packet mem: 8022d380 (0xe00000 bytes)
********************************************

NET: Registered protocol family 16
PCI init:ath_pcibios_init
ath_pcibios_init(294): PCI CMD write: 0x356
registering PCI controller with io_map_base unset
WIFI button pressed.
bio: create slab <bio-0> at 0
pci 0000:00:00.0: PME# supported from D0 D1 D3hot
pci 0000:00:00.0: PME# disabled
Returning IRQ 64
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 4096 (order: 3, 32768 bytes)
TCP bind hash table entries: 4096 (order: 2, 16384 bytes)
TCP: Hash tables configured (established 4096 bind 4096)
TCP reno registered
NET: Registered protocol family 1
ATH GPIOC major 0
squashfs: version 4.0 (2009/01/31) Phillip Lougher
msgmni has been set to 221
io scheduler noop registered
io scheduler deadline registered (default)
Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled
serial8250.0: ttyS0 at MMIO 0xb8020000 (irq = 19) is a 16550A
console [ttyS0] enabled
PPP generic driver version 2.4.2
NET: Registered protocol family 24
5 cmdlinepart partitions found on MTD device ath-nor0
Creating 5 MTD partitions on "ath-nor0":
0x000000000000-0x000000020000 : "u-boot"
0x000000020000-0x000000120000 : "kernel"
0x000000120000-0x0000007e0000 : "rootfs"
0x0000007e0000-0x0000007f0000 : "config"
0x0000007f0000-0x000000800000 : "ART"
->Oops: flash id 0xef4017 .
TCP cubic registered
NET: Registered protocol family 17
802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
All bugs added by David S. Miller <davem@redhat.com>
athwdt_init: Registering WDT success
ath_otp_init: Registering OTP success
ath_clksw_init: Registering Clock Switch Interface success
VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
Freeing unused kernel memory: 112k freed

init started:  BusyBox v1.01 (2012.02.11-02:20+0000) multi-call binary
This Board use 2.6.31
xt_time: kernel timezone is -0000
nf_conntrack version 0.5.0 (2048 buckets, 5120 max)
CONFIG_NF_CT_ACCT is deprecated and will be removed soon. Please use
nf_conntrack.acct=1 kernel parameter, acct=1 nf_conntrack module option or
sysctl net.netfilter.nf_conntrack_acct=1 to enable it.
ip_tables: (C) 2000-2006 Netfilter Core Team
insmod: cannot open module `/lib/modules/2.6.31/kernel/iptable_raw.ko': No such file or directory
insmod: cannot open module `/lib/modules/2.6.31/kernel/flashid.ko': No such file or directory
PPPoL2TP kernel driver, V1.0
PPTP driver version 0.8.3
insmod: cannot open module `/lib/modules/2.6.31/kernel/harmony.ko': No such file or directory
Now flash open!

(none) mips #1 Thu Apr 26 08:21:33 PDT 2012 (none)

(none) login: Now flash open!
ATHR_GMAC: Length per segment 1536
ATHR_GMAC: fifo cfg 3 01f00140
ATHR_GMAC: RX TASKLET - Pkts per Intr:100
ATHR_GMAC: Mac address for unit 0:bfff0000
ATHR_GMAC: ff:ff:ff:ff:ff:ff
ATHR_GMAC: Max segments per packet :   1
ATHR_GMAC: Max tx descriptor count :   128
ATHR_GMAC: Max rx descriptor count :   128
ATHR_GMAC: Mac capability flags    :   2381
athr_gmac_ring_alloc Allocated 2048 at 0x8784a000
athr_gmac_ring_alloc Allocated 2048 at 0x87a8c800
WASP  ----> S17 PHY *
Setting Drop CRC Errors, Pause Frames and Length Error frames
Hello, nat module!
thread: napt_ct_scan create success pid:95
netlink_kernel_create succeeded at tp_rule_nl_prot: [29]
isis_ip_intf_entry_add id[0] for vid[1]
isis_ip_intf_entry_add id[1] for vid[2]
ACL(Index 0) For packet From Wan Port and TTL is zero
ACL is not yet enabled. Enabling...
ACL Rule(Index 2) For UDP with Zero Checksum

######## S17 SSDK init succeeded! ########
++++ athrs17_igmp_setup once
athrs17_reg_init:done
Setting PHY...
napt_ct_scan_thread: time: 4
device eth0.1 entered promiscuous mode
device eth0 entered promiscuous mode
isis_ip_intf_entry_add id[1] for vid[2]
Now flash open!
br0: port 1(eth0.1) entering forwarding state
ACL Rule(Index 1) For Packet From WAN to LAN Port And DIP is in lan net
nf_conntrack_rtsp v0.6.21 loading
nf_nat_rtsp v0.6.21 loading
asf: module license 'Proprietary' taints kernel.
Disabling lock debugging due to kernel taint
ath_hal: 0.9.17.1 (AR5416, AR9380, REGOPS_FUNC, WRITE_EEPROM, 11D)
ath_rate_atheros: Copyright (c) 2001-2005 Atheros Communications, Inc, All Rights Reserved
ath_dfs: Version 2.0.0
Copyright (c) 2005-2006 Atheros Communications, Inc. All Rights Reserved
ath_dev: Copyright (c) 2001-2007 Atheros Communications, Inc, All Rights Reserved
ath_ahb: 9.2.0_U10.1020 (Atheros/multi-bss)
__ath_attach: Set global_scn[0]
ACBKMinfree = 48
ACBEMinfree = 32
ACVIMinfree = 16
ACVOMinfree = 0
CABMinfree = 48
UAPSDMinfree = 0
Restoring Cal data from Flash
dfs_attach: use DFS enhancements
DFS min filter rssiThresh = 18
DFS max pulse dur = 151 ticks
ath_get_caps[5105] rx chainmask mismatch actual 3 sc_chainmak 0
ath_get_caps[5080] tx chainmask mismatch actual 3 sc_chainmak 0
SC Callback Registration for wifi0
wifi0: Atheros 9340: mem=0xb8100000, irq=2
ath_pci: 9.2.0_U10.1020 (Atheros/multi-bss)
__ath_attach: Set global_scn[1]
ACBKMinfree = 48
ACBEMinfree = 32
ACVIMinfree = 16
ACVOMinfree = 0
CABMinfree = 48
UAPSDMinfree = 0
Restoring Cal data from Flash
dfs_attach: use DFS enhancements
DFS min filter rssiThresh = 18
DFS max pulse dur = 151 ticks
ath_get_caps[5105] rx chainmask mismatch actual 7 sc_chainmak 0
ath_get_caps[5080] tx chainmask mismatch actual 7 sc_chainmak 0
SC Callback Registration for wifi1
wifi1: Atheros 9580: mem=0x10000000, irq=64 hw_base=0xb0000000
dfs_init_radar_filters: Unknown dfs domain 0
wlan_vap_create : enter. devhandle=0x87b7c2c0, opmode=IEEE80211_M_HOSTAP, flags=0x1
wlan_vap_create : exit. devhandle=0x87b7c2c0, opmode=IEEE80211_M_HOSTAP, flags=0x1.
VAP device ath0 created

savi***

DES SSID SET=Mercury_2.4GHz_F2D792
ieee80211_ioctl_siwmode: imr.ifm_active=131712, new mode=3, valid=1
device ath0 entered promiscuous mode
br0: port 2(ath0) entering forwarding state
ieee80211_ioctl_siwmode: imr.ifm_active=918144, new mode=3, valid=1
br0: port 2(ath0) entering disabled state

DES SSID SET=Mercury_2.4GHz_F2D792
br0: port 2(ath0) entering forwarding state
br0: port 2(ath0) entering disabled state
br0: starting userspace STP failed, starting kernel STP
br0: topology change detected, propagating
br0: port 2(ath0) entering forwarding state
dfs_init_radar_filters: Unknown dfs domain 0
wlan_vap_create : enter. devhandle=0x86db42c0, opmode=IEEE80211_M_HOSTAP, flags=0x1
wlan_vap_create : exit. devhandle=0x86db42c0, opmode=IEEE80211_M_HOSTAP, flags=0x1.
VAP device ath1 created

DES SSID SET=Mercury_5GHz_F2D793
ieee80211_ioctl_siwmode: imr.ifm_active=66176, new mode=3, valid=1
Found best 11na chan: 149
br0: port 1(eth0.1) entering disabled state
br0: topology change detected, propagating
br0: port 1(eth0.1) entering forwarding state
device ath1 entered promiscuous mode
br0: topology change detected, propagating
br0: port 3(ath1) entering forwarding state
ieee80211_ioctl_siwmode: imr.ifm_active=852608, new mode=3, valid=1
br0: port 3(ath1) entering disabled state

DES SSID SET=Mercury_5GHz_F2D793
br0: topology change detected, propagating
br0: port 3(ath1) entering forwarding state
br0: port 3(ath1) entering disabled state
br0: topology change detected, propagating
br0: port 3(ath1) entering forwarding state
fuse init (API version 7.12)
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
Port Status 1c000004
ath-ehci ath-ehci.0: ATH EHCI
ath-ehci ath-ehci.0: new USB bus registered, assigned bus number 1
ehci_reset Intialize USB CONTROLLER in host mode: 13
ehci_reset Port Status 1c000000
ath-ehci ath-ehci.0: irq 3, io mem 0x1b000000
ehci_reset Intialize USB CONTROLLER in host mode: 13
ehci_reset Port Status 1c000000
ath-ehci ath-ehci.0: USB 2.0 started, EHCI 1.00
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
SCSI subsystem initialized
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
GPL NetUSB up!
kc   88 : run_telnetDBGDServer start
kc  225 : init_DebugD end
INFO16B9: NetUSB 1.161, 0002061F : Feb 29 2012 15:22:09
INFO16BB:  AUTH ISOC
INFO16BC:
usbcore: registered new interface driver KC NetUSB General Driver
INFO0076:  init proc : PAGE_SIZE 4096
INFO1715: Check mac address
INFO1575:  sleep to wait br0 to wake up
INFO02D0:  use dev Name br0
INFO157E:  sleep to wait br0 end.
INFO1597:  UDP_BROAD 7437 tcpPort:625868800
INFO02D0:  use dev Name br0
my server name : TL-WDR4300
INFO14CE: tcpConnector() started...
TP_RULE_NAT:enable hardware nat
INFO13AB: Bind to br0

MW4530R mips #1 Thu Apr 26 08:21:33 PDT 2012 (none)

MW4530R login:

过期***

能备份原版的uboot和编程器固件吗？

savi***

固件没了，刷openwrt了，4300有固件，当那个是原厂就是了。

pu***

这个固件怎么和另外一个地方的分区不一样https://www.right.com.cn/forum/thread-88895-1-1.html

你的：U-Boot 1.1.4
Kernel command line: console=ttyS0,115200 root=31:02 rootfstype=squashfs init=/sbin/init mtdparts=ath-nor0:128k(u-boot),1024k(kernel),6912k(rootfs),64k(config),64k(ART) mem=128M

别人的：
console=ttyS0,115200 root=31:02 rootfstype=squashfs init=/sbin/init mtdparts=ath-nor0:256k(u-boot),64k(u-boot-env),6336k(rootfs),1408k(uImage),64k(mib0),64k(ART)

hana***

思考一下

半个***

感谢分享