【2022-07-26】AR/QCA/MTK Breed，功能强大的多线程 Bootloader

vic-dou · 发表于 2015-3-21 22:56

都是开发高手，顶帖致谢！

vic-dou · 发表于 2015-3-23 21:37

Broadcom玩够了，openwrt才是玩的境界！

vic-dou · 发表于 2015-4-6 01:33

本帖最后由 vic-dou 于 2015-4-6 01:37 编辑

楼主大神，提个现象。
路由宝刷了最新425和上一个419版本。已经支持中断breed 时四灯同时闪烁，之前是两个灯。

但是进Breed时，4个灯都灭了，我觉得很奇怪，使用telnet命令Gpio led 一看，WAN是on 的啊，怎么不亮。

原来需要把网线插进路由的WAN口才会亮(我知道这个端口顺序不重要，WAN会变成LAN)。

请求楼主将Breed中定义的Sys灯变成Power灯，优酷灯变成系统状态闪烁灯(应该就是SYS灯，是吧)

这样的话：
开机PWR(sys)常亮，sys(Youku)闪烁

vic-dou · 发表于 2015-4-7 09:07

假如只能长亮，楼主，能否将Breed中定义的sys灯长亮，Youku灯定义为任意网口插网线有数据流时闪烁。

vic-dou · 发表于 2015-4-7 14:06

好吧，我懂了，路由宝没有对应LAN的灯，所以，谢谢科普！

vic-dou · 发表于 2015-4-29 21:48

520版本出来了，非常感谢！

vic-dou · 发表于 2015-4-29 21:51

本帖最后由 vic-dou 于 2015-4-30 10:02 编辑

算了，我拿我的841 v8去交易处和其他人换其他路由器。

vic-dou · 发表于 2015-5-11 11:17

楼主能否提供breed的md5值，我觉得这个非常重要

vic-dou · 发表于 2015-5-13 21:09

明天刷Breed，9341来了。

vic-dou · 发表于 2015-5-14 08:10

703n656 发表于 2015-5-14 01:42
呜呜、
我的703n 16M 由不死刷 breed-ar9331.bin r585 固件
成功变成砖头了！！

由哪个版本升级的？
我的841 V8的9341曾经04.27版本降级到03.09版本失败，灯全亮！

vic-dou · 发表于 2015-5-14 10:58

1、设备：WR841N V8 AR9341 8M/64M
刷国际版的“_wr940ndv2_wr941ndv5_en_3_16_9_up_boot(150311).bin” 存在指示灯显示问题。
我知道路由本身刷国际版“wr843ndv1_en_3_14_9_up_boot(140410).bin” 端口顺序反序，但是指示灯正常

问题描述：国际版940NV2的WAN（LAN1）、LAN1(LAN2)、 LAN2(LAN3)插入网线或断开网线，指示灯均正常。
只有LAN3(LAN4)、LAN4(WAN)不正常，LAN3(LAN4)表现为灯一直极快微亮闪烁，不管是否插入或拔出网线；LAN4(WAN)表现为灯一直长灭，不管是否插入或拔出网线。

2、Breed“恢复出厂设置”功能似乎不能自动识别“openwrt固件”和“TP原厂固件”（之前楼主大神的U-boot是可以识别的），我使用的是明月的openwrt-mingyue-20150307-14.07-ar71xx-generic-tl-wr841n-v8-squashfs-sysupgrade.bin，打开Breed“恢复出厂设置”显示为“TP-LINK（原厂）”

TTL显示

Boot and Recovery Environment for Embedded Devices
Copyright (C) 2015 HackPascal <hackpascal@gmail.com>
Build date 2015-05-13 [git-3ab38fa]
Version 1.0 (r585)
DRAM: 64MB
Platform: Atheros AR9341 rev 1
Board: Atheros AP123 reference board
Clocks: CPU: 560MHz, DDR: 400MHz, AHB: 200MHz, Ref: 25MHz
Flash: EON EN25Q64 (8MB) on ath79-spi
ag71xx-eth: MAC address is invalid, using default settings.
ag71xx-eth: Using MAC address 00:13:74:00:00:01
eth0: Atheros AR8228/AR8229 rev 1
Network started on eth0, inet addr 192.168.1.1, netmask 255.255.255.0
Press any key to interrupt autoboot ... 0
Trying to boot firmware from 0x9f020000 ...
TP-LINK firmware image header detected.
Image Name: 09410005
Data Size: 837392 Bytes
Load Address: 80002000
Entry Point: 801b8400
Uncompressing data (LZMA) ... done.
Flushing cache ... done.
Starting kernel at 0x801b8400...
Booting Atheros AR934x
Linux version 2.6.31--LSDK-9.2.0_U10.5_dsa.7 (tomcat@buildserver) (gcc version 4.3.3 (GCC) ) #32 Wed Mar 11 17:12:15 CST 2015
flash_size passed from bootloader = 8
Ram size passed from bootloader =67108864
CPU revision is: 0001974c (MIPS 74Kc)
ath_sys_frequency: cpu srif ddr srif cpu 560 ddr 400 ahb 200
Determined physical RAM map:
memory: 04000000 @ 00000000 (usable)
Zone PFN ranges:
Normal 0x00000000 -> 0x00004000
Movable zone start PFN for each node
early_node_map[1] active PFN ranges
0: 0x00000000 -> 0x00004000
Built 1 zonelists in Zone order, mobility grouping on. Total pages: 16256
Kernel command line: console=ttyS0,115200 root=31:2 rootfstype=squashfs init=/sbin/init mtdparts=ath-nor0:128k(u-boot),1024k(kernel),2816k(rootfs),64k(config),64k(art) mem=32M
PID hash table entries: 256 (order: 8, 1024 bytes)
Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
Writing ErrCtl register=00000000
Readback ErrCtl register=00000000
Memory: 62480k/65536k available (1781k kernel code, 2988k reserved, 436k data, 116k init, 0k highmem)
NR_IRQS:128
plat_time_init: plat time init done
Calibrating delay loop... 279.55 BogoMIPS (lpj=559104)
Mount-cache hash table entries: 512
NET: Registered protocol family 16
bio: create slab <bio-0> at 0
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
net_link: create socket ok.
TCP established hash table entries: 2048 (order: 2, 16384 bytes)
TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
TCP: Hash tables configured (established 2048 bind 2048)
TCP reno registered
NET: Registered protocol family 1
ATH GPIOC major 0
squashfs: version 4.0 (2009/01/31) Phillip Lougher
msgmni has been set to 122
io scheduler noop registered
io scheduler deadline registered (default)
Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled
serial8250.0: ttyS0 at MMIO 0xb8020000 (irq = 19) is a 16550A
console [ttyS0] enabled
PPP generic driver version 2.4.2
NET: Registered protocol family 24
5 cmdlinepart partitions found on MTD device ath-nor0
Creating 5 MTD partitions on "ath-nor0":
0x000000000000-0x000000020000 : "u-boot"
0x000000020000-0x000000120000 : "kernel"
0x000000120000-0x0000003e0000 : "rootfs"
0x0000003e0000-0x0000003f0000 : "config"
0x0000003f0000-0x000000400000 : "art"
->Oops: flash id 0x1c3017 .
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
Port Status 1c000004
ath-ehci ath-ehci.0: ATH EHCI
ath-ehci ath-ehci.0: new USB bus registered, assigned bus number 1
ehci_reset Intialize USB CONTROLLER in host mode: 13
ehci_reset Port Status 1c000000
ath-ehci ath-ehci.0: irq 3, io mem 0x1b000000
ehci_reset Intialize USB CONTROLLER in host mode: 13
ehci_reset Port Status 1c000000
ath-ehci ath-ehci.0: USB 2.0 started, EHCI 1.00
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
Ooops, why the devices couldn't been initialed?
TCP cubic registered
NET: Registered protocol family 17
802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
All bugs added by David S. Miller <davem@redhat.com>
athwdt_init: Registering WDT success
ath_otp_init: Registering OTP success
ath_clksw_init: Registering Clock Switch Interface success
VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
Freeing unused kernel memory: 116k freed
init started: BusyBox v1.01 (2015.03.11-09:15+0000) multi-call binary
This Board use 2.6.31
xt_time: kernel timezone is -0000
nf_conntrack version 0.5.0 (1024 buckets, 5120 max)
ip_tables: (C) 2000-2006 Netfilter Core Team
insmod: cannot open module `/lib/modules/2.6.31/kernel/iptable_raw.ko': No such file or directory
insmod: cannot open module `/lib/modules/2.6.31/kernel/flashid.ko': No such file or directory
PPPoL2TP kernel driver, V1.0
PPTP driver version 0.8.3
insmod: cannot open module `/lib/modules/2.6.31/kernel/harmony.ko': No such file or directory
insmod: cannot open module `/lib/modules/2.6.31/kernel/af_key.ko': No such file or directory
insmod: cannot open module `/lib/modules/2.6.31/kernel/xfrm_user.ko': No such file or directory
Now flash open!
Now flash open!
(none) mips #32 Wed Mar 11 17:12:15 CST 2015 (none)
(none) login: ATHR_GMAC: Length per segment 1536
ATHR_GMAC: fifo cfg 3 01f00140
ATHR_GMAC: RX TASKLET - Pkts per Intr:32
mac:1 Registering S27....
ATHR_GMAC: Max segments per packet : 1
ATHR_GMAC: Max tx descriptor count : 40
ATHR_GMAC: Max rx descriptor count : 128
ATHR_GMAC: Mac capability flags : 2D82
ATHR_GMAC: RX TASKLET - Pkts per Intr:32
mac:0 Registering S27....
ATHR_GMAC: Max segments per packet : 1
ATHR_GMAC: Max tx descriptor count : 40
ATHR_GMAC: Max rx descriptor count : 128
ATHR_GMAC: Mac capability flags : 2582
athr_gmac_ring_alloc Allocated 640 at 0x83a37c00
athr_gmac_ring_alloc Allocated 2048 at 0x838ca000
WASP ----> S27 PHY MDIO
Setting Drop CRC Errors, Pause Frames and Length Error frames
ATHRS27: resetting s27
ATHRS27: s27 reset done
++++ athrs27_igmp_setup once
port0 vid is 0xb000b
port1 vid is 0x30003
port2 vid is 0x50005
port3 vid is 0x70007
port4 vid is 0x90009
++ PVID: 0x0000000b, bitmap: 0x0000001f
++ PVID: 0x00000003, bitmap: 0x0000001f
++ PVID: 0x00000005, bitmap: 0x0000001f
++ PVID: 0x00000007, bitmap: 0x0000001f
++ PVID: 0x00000009, bitmap: 0x0000001f
vtable vid: 0x00000002, bitmap 0x00000003
vtable vid: 0x00000004, bitmap 0x00000005
vtable vid: 0x00000006, bitmap 0x00000007
vtable vid: 0x00000008, bitmap 0x00000009
vtable vid: 0x0000000a, bitmap 0x0000000b
vtable vid: 0x0000000c, bitmap 0x0000000d
vtable vid: 0x0000000e, bitmap 0x0000000f
vtable vid: 0x00000010, bitmap 0x00000011
vtable vid: 0x00000012, bitmap 0x00000013
vtable vid: 0x00000014, bitmap 0x00000015
vtable vid: 0x00000016, bitmap 0x00000017
vtable vid: 0x00000018, bitmap 0x00000019
vtable vid: 0x0000001a, bitmap 0x0000001b
vtable vid: 0x0000001c, bitmap 0x0000001d
vtable vid: 0x0000001e, bitmap 0x0000001f
vtable vid: 0x00000020, bitmap 0x00000021
Setting PHY...
athr_gmac_ring_alloc Allocated 640 at 0x83a37000
athr_gmac_ring_alloc Allocated 2048 at 0x83a94000
WASP ----> S27 PHY MDIO
Setting Drop CRC Errors, Pause Frames and Length Error frames
Setting PHY...
device eth0 entered promiscuous mode
Now flash open!
athr_gmac_ring_free Freeing at 0x83a37000
athr_gmac_ring_free Freeing at 0x83a94000
athr_gmac_ring_alloc Allocated 640 at 0x83a37000
athr_gmac_ring_alloc Allocated 2048 at 0x83b09800
enet1 port2 up 100Mbps Full duplex
ATHR_GMAC: Enet Unit:1 PHY:2 is UP RGMii 100Mbps full duplex
ATHR_GMAC: done cfg2 0x7215 ifctl 0x0 miictrl
WASP ----> S27 PHY MDIO
Setting Drop CRC Errors, Pause Frames and Length Error frames
WASP ----> S27 PHY MDIO
Setting Drop CRC Errors, Pause Frames and Length Error frames
Setting PHY...
athr_gmac_ring_free Freeing at 0x83a37c00
athr_gmac_ring_free Freeing at 0x838ca000
athr_gmac_ring_alloc Allocated 640 at 0x83a37c00
athr_gmac_ring_alloc Allocated 2048 at 0x83a3c800
WASP ----> S27 PHY MDIO
Setting Drop CRC Errors, Pause Frames and Length Error frames
Setting PHY...
enet1 port2 up 100Mbps Full duplex
ATHR_GMAC: Enet Unit:1 PHY:2 is UP RGMii 100Mbps full duplex
ATHR_GMAC: done cfg2 0x7215 ifctl 0x0 miictrl
WASP ----> S27 PHY MDIO
Setting Drop CRC Errors, Pause Frames and Length Error frames
br0: port 1(eth0) entering forwarding state
nf_conntrack_rtsp v0.6.21 loading
nf_nat_rtsp v0.6.21 loading
asf: module license 'Proprietary' taints kernel.
Disabling lock debugging due to kernel taint
ath_hal: 0.9.17.1 (AR5416, AR9380, REGOPS_FUNC, WRITE_EEPROM, 11D)
ath_rate_atheros: Copyright (c) 2001-2005 Atheros Communications, Inc, All Rights Reserved
ath_dev: Copyright (c) 2001-2007 Atheros Communications, Inc, All Rights Reserved
ath_ahb: 9.2.0_U10.5_dsa.7 (Atheros/multi-bss)
__ath_attach: Set global_scn[0]
ACBKMinfree = 48
ACBEMinfree = 32
ACVIMinfree = 16
ACVOMinfree = 0
CABMinfree = 48
UAPSDMinfree = 0
Wasp Enterprise mode: 0x00000000
Restoring Cal data from Flash
ath_get_caps[5154] rx chainmask mismatch actual 3 sc_chainmak 0
ath_get_caps[5129] tx chainmask mismatch actual 3 sc_chainmak 0
wifi0: Atheros 9340: mem=0xb8100000, irq=2
wlan_vap_create : enter. devhandle=0x8302c2c0, opmode=IEEE80211_M_HOSTAP, flags=0x1
wlan_vap_create : exit. devhandle=0x8302c2c0, opmode=IEEE80211_M_HOSTAP, flags=0x1.
VAP device ath0 created
Setting Max Stations:33
DES SSID SET=TP-LINK_33CC
ieee80211_ioctl_siwmode: imr.ifm_active=131712, new mode=3, valid=1
athr_gmac_ring_free Freeing at 0x83a37c00
athr_gmac_ring_free Freeing at 0x83a3c800
br0: port 1(eth0) entering disabled state
athr_gmac_ring_alloc Allocated 640 at 0x83a37c00
athr_gmac_ring_alloc Allocated 2048 at 0x83a3c000
WASP ----> S27 PHY MDIO
Setting Drop CRC Errors, Pause Frames and Length Error frames
Setting PHY...
device ath0 entered promiscuous mode
br0: port 2(ath0) entering forwarding state
ieee80211_ioctl_siwmode: imr.ifm_active=918144, new mode=3, valid=1
br0: port 2(ath0) entering disabled state
DES SSID SET=TP-LINK_33CC
br0: port 2(ath0) entering forwarding state
enet1 port2 up 100Mbps Full duplex
ATHR_GMAC: Enet Unit:1 PHY:2 is UP RGMii 100Mbps full duplex
ATHR_GMAC: done cfg2 0x7215 ifctl 0x0 miictrl
WASP ----> S27 PHY MDIO
Setting Drop CRC Errors, Pause Frames and Length Error frames
br0: port 1(eth0) entering forwarding state
ATHR_GMAC: GE0 RX DMA ENABLE
enet1 port2 down
ATHR_GMAC:unit 1: phy 2 not up carrier 1
br0: port 1(eth0) entering disabled state
enet1 port1 up 100Mbps Full duplex
ATHR_GMAC: Enet Unit:1 PHY:1 is UP RGMii 100Mbps full duplex
ATHR_GMAC: done cfg2 0x7215 ifctl 0x0 miictrl
WASP ----> S27 PHY MDIO
Setting Drop CRC Errors, Pause Frames and Length Error frames
br0: port 1(eth0) entering forwarding state
enet1 port1 down
ATHR_GMAC:unit 1: phy 1 not up carrier 1
br0: port 1(eth0) entering disabled state
enet1 port2 up 100Mbps Full duplex
ATHR_GMAC: Enet Unit:1 PHY:2 is UP RGMii 100Mbps full duplex
ATHR_GMAC: done cfg2 0x7215 ifctl 0x0 miictrl
WASP ----> S27 PHY MDIO
Setting Drop CRC Errors, Pause Frames and Length Error frames
br0: port 1(eth0) entering forwarding state
enet1 port2 down
ATHR_GMAC:unit 1: phy 2 not up carrier 1
br0: port 1(eth0) entering disabled state
enet1 port3 up 100Mbps Full duplex
ATHR_GMAC: Enet Unit:1 PHY:3 is UP RGMii 100Mbps full duplex
ATHR_GMAC: done cfg2 0x7215 ifctl 0x0 miictrl
WASP ----> S27 PHY MDIO
Setting Drop CRC Errors, Pause Frames and Length Error frames
br0: port 1(eth0) entering forwarding state
enet1 port3 down
ATHR_GMAC:unit 1: phy 3 not up carrier 1
br0: port 1(eth0) entering disabled state
enet1 port4 up 100Mbps Full duplex
ATHR_GMAC: Enet Unit:1 PHY:4 is UP RGMii 100Mbps full duplex
ATHR_GMAC: done cfg2 0x7215 ifctl 0x0 miictrl
WASP ----> S27 PHY MDIO
Setting Drop CRC Errors, Pause Frames and Length Error frames
br0: port 1(eth0) entering forwarding state
enet1 port4 down
ATHR_GMAC:unit 1: phy 4 not up carrier 1
br0: port 1(eth0) entering disabled state
enet1 port1 up 100Mbps Full duplex
ATHR_GMAC: Enet Unit:1 PHY:1 is UP RGMii 100Mbps full duplex
ATHR_GMAC: done cfg2 0x7215 ifctl 0x0 miictrl
WASP ----> S27 PHY MDIO
Setting Drop CRC Errors, Pause Frames and Length Error frames
br0: port 1(eth0) entering forwarding state
enet1 port1 down
ATHR_GMAC:unit 1: phy 1 not up carrier 1
br0: port 1(eth0) entering disabled state

复制代码

vic-dou · 发表于 2015-5-14 11:55

WR841N V8
qss和reset复用键 GPIO=17 lo

vic-dou · 发表于 2015-5-14 12:34

hackpascal 发表于 2015-5-14 12:20
文件没错只是帖子上写错了

了解，谢谢，楼主的Breed速度比不死U-boot快多了。

vic-dou · 发表于 2015-5-14 15:19

asw333 发表于 2015-5-14 14:33
我以为是刷了breed之后手动把MAC改回之前的，难道是说必需把之前的MAC改成其他的？尴尬了。。。

应该刷了之后再改，你是千兆可能特殊点。

楼主，被吃掉的那层楼出来了。Breed 779楼

vic-dou · 发表于 2015-5-14 16:29

703n656 发表于 2015-5-14 16:24
我的砖头也是灯全亮用的不死UBOOT是 0427的

这一次从u-boot升级到breed，我学聪明了，进openwrt使用mtd -r write命令刷的。

账号		自动登录	找回密码
密码			立即注册

【2022-07-26】AR/QCA/MTK Breed，功能强大的多线程 Bootloader

点评

点评

点评

本帖子中包含更多资源

点评