设为首页收藏本站

恩山无线论坛

 找回密码
 立即注册

QQ登录

只需一步,快速开始

搜索
楼主: hackpascal

【2017-09-21】AR/QCA/MTK Breed,功能强大的多线程 Bootloader

    [复制链接]
发表于 2015-10-25 23:50 | 显示全部楼层
LG 6000和841 v7 方案相同 刷了最新的会反复进入bread  12 28目前再用其他都不可以
我的恩山、我的无线 The best wifi forum is right here.
发表于 2015-10-26 12:03 | 显示全部楼层
本帖最后由 wowfans 于 2015-10-26 13:46 编辑

能出个941N V6  / 2041N V1 (AR9344 + ar9381 )的 8M  / 16M闪存容量版本的breed吗?原版4M太小了,想换个闪存,或者提供一个修改方法?
-------------

老大麻烦看下我这么搞有没有问题。

好吧,刚才翻了楼主大神的之前的U-BOOT的帖子,貌似之前的u-boot都自动识别闪存容量,所以新的breed应该是具有该特性的。
另外好像2041n v1虽然硬件配置和941n v6一样,就多了一个turbo按钮,但据说貌似不能用941n v6的专用breed,得用ar9344通用的breed。

因为卖家也不太会玩,但他有编程器,可以更换FLASH,刷入编程器固件。
于是我想这样组合,制造编程器固件,不知道是否可行。

硬件: 2041n v1,硬改8M闪存

编程器固件由一下3部分顺序粘贴:
1。老大的breed-ar9344.bin百兆通用版最新版。 这个大小83KB,我会将其从0位置开始写入,占据大小是128KB,83~128KB区间全是00


2。openwrt-ar71xx-generic-tl-wr941nd-v6-cn-squashfs-factory.bin  这个文件是openwrt官网的最新的10.18日的固件,大小正好3840KB(3.75MB),后面的用00填充64KB 再继续填充4096KB,整个区域大小是=3840+64+4096 = 8000KB

3。再从8128KB的位置开始写入老大对应的ar9344+ar9381的ART,这个是64KB。

于是整个编程器固件大小就是128KB+8000KB+64KB=8192KB,正好是8MB

应该没问题吧。。。。还需要补充什么吗?

U-BOOT部分肯定没问题,老大的breed自动识别闪存大小,主要是4MB的openwrt系统是否能自动识别闪存是8MB的??后期箱装软件会不会提示空间不足?(实际上还剩一大半)
我的恩山、我的无线 The best wifi forum is right here.
发表于 2015-10-26 12:17 | 显示全部楼层
hackpascal 发表于 2015-3-21 22:38
小米 Mini 固件启动设置

进入 Breed 恢复控制台

顶一下,希望换芯片能成功……
我的恩山、我的无线 The best wifi forum is right here.
发表于 2015-10-26 14:49 | 显示全部楼层
楼主,我手里有一批7620a 魔豆路由器101C 有兴趣折腾吗?免费提供研发啊啊啊 我也是个爱好者
我的恩山、我的无线 The best wifi forum is right here.
发表于 2015-10-26 17:58 | 显示全部楼层
我的恩山、我的无线 The best wifi forum is right here.
发表于 2015-10-26 18:21 | 显示全部楼层
膜拜楼主,标记备用
我的恩山、我的无线 The best wifi forum is right here.
发表于 2015-10-26 21:27 | 显示全部楼层
本帖最后由 smilemoon 于 2015-10-26 21:47 编辑
smilemoon 发表于 2015-10-22 11:55
wr800n v1 能刷842ND V2,今天刷了H大神的最新的 Breed r777 [2015-10-18],可以正常启动了,但是用842NDV2 ...

Restarting system.

Boot and Recovery Environment for Embedded Devices
Copyright (C) 2015 HackPascal <[email protected]>
Build date 2015-10-18 [git-bb5218f]
Version 1.0 (r777)

DRAM: 32MB
Platform: Atheros AR9341 rev 3
Board: Atheros AP123 reference board
Clocks: CPU: 560MHz, DDR: 400MHz, AHB: 200MHz, Ref: 25MHz
Flash: Winbond W25Q64 (8MB) on ath79-spi
ag71xx-eth: Using MAC address 0c:82:68:af:cc:16
eth0: Atheros AR8228/AR8229 rev 1

Network started on eth0, inet addr 192.168.1.1, netmask 255.255.255.0

Press any key to interrupt autoboot ... 0   

Trying to boot firmware from 0x9f020000 ...
TP-LINK firmware image header detected.
    Image Name:   08420002
    Data Size:    845472 Bytes
    Load Address: 80002000
    Entry Point:  801aeb70
Uncompressing data (LZMA) ... done.
Flushing cache ... done.

Starting kernel at 0x801aeb70...

Booting Atheros AR934x
Linux version 2.6.31--LSDK-9.2.0_U5.508 ([email protected]) (gcc version 4.3.3 (GCC) ) #3 Fri Jun 28 10:10:08 CST 2013
flash_size passed from bootloader = 8
Ram size passed from bootloader =33554432
CPU revision is: 0001974c (MIPS 74Kc)
ath_sys_frequency: cpu srif ddr srif cpu 560 ddr 400 ahb 200
Determined physical RAM map:
memory: 02000000 @ 00000000 (usable)
Zone PFN ranges:
  Normal   0x00000000 -> 0x00002000
Movable zone start PFN for each node
early_node_map[1] active PFN ranges
    0: 0x00000000 -> 0x00002000
Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 8128
Kernel command line: console=ttyS0,115200 root=31:2 rootfstype=squashfs init=/sbin/init mtdparts=ath-nor0:128k(u-boot),1024k(kernel),6912k(rootfs),64k(config),64k(art) mem=32M
PID hash table entries: 128 (order: 7, 512 bytes)
Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)
Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)
Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
Writing ErrCtl register=000000c0
Readback ErrCtl register=000000c0
Memory: 30036k/32768k available (1742k kernel code, 2732k reserved, 498k data, 116k init, 0k highmem)
NR_IRQS:128
plat_time_init: plat time init done
Calibrating delay loop... 279.55 BogoMIPS (lpj=559104)
Mount-cache hash table entries: 512
NET: Registered protocol family 16
bio: create slab <bio-0> at 0
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 1024 (order: 1, 8192 bytes)
TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
TCP: Hash tables configured (established 1024 bind 1024)
TCP reno registered
NET: Registered protocol family 1
ATH GPIOC major 0
squashfs: version 4.0 (2009/01/31) Phillip Lougher
msgmni has been set to 58
alg: No test for cipher_null (cipher_null-generic)
alg: No test for ecb(cipher_null) (ecb-cipher_null)
alg: No test for digest_null (digest_null-generic)
alg: No test for compress_null (compress_null-generic)
alg: No test for lzma (lzma-generic)
alg: No test for stdrng (krng)
alg: No test for stdrng (ansi_cprng)
io scheduler noop registered
io scheduler deadline registered (default)
Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled
serial8250.0: ttyS0 at MMIO 0xb8020000 (irq = 19) is a 16550A
console [ttyS0] enabled
PPP generic driver version 2.4.2
NET: Registered protocol family 24
5 cmdlinepart partitions found on MTD device ath-nor0
Creating 5 MTD partitions on "ath-nor0":
0x000000000000-0x000000020000 : "u-boot"
0x000000020000-0x000000120000 : "kernel"
0x000000120000-0x0000007e0000 : "rootfs"
0x0000007e0000-0x0000007f0000 : "config"
0x0000007f0000-0x000000800000 : "art"
->Oops: flash id 0xef4017 .
Ooops, why the devices couldn't been initialed?
TCP cubic registered
NET: Registered protocol family 17
802.1Q VLAN Support v1.8 Ben Greear <[email protected]>
All bugs added by David S. Miller <[email protected]>
athwdt_init: Registering WDT success
ath_otp_init: Registering OTP success
ath_clksw_init: Registering Clock Switch Interface success
VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
Freeing unused kernel memory: 116k freed
init started:  BusyBox v1.01 (2013.06.28-02:15+0000) multi-call binary
This Board use 2.6.31
xt_time: kernel timezone is -0000
nf_conntrack version 0.5.0 (512 buckets, 5120 max)
CONFIG_NF_CT_ACCT is deprecated and will be removed soon. Please use
nf_conntrack.acct=1 kernel parameter, acct=1 nf_conntrack module option or
sysctl net.netfilter.nf_conntrack_acct=1 to enable it.
ip_tables: (C) 2000-2006 Netfilter Core Team
insmod: cannot open module `/lib/modules/2.6.31/kernel/iptable_raw.ko': No such file or directory
insmod: cannot open module `/lib/modules/2.6.31/kernel/flashid.ko': No such file or directory
PPPoL2TP kernel driver, V1.0
PPTP driver version 0.8.3
insmod: cannot open module `/lib/modules/2.6.31/kernel/harmony.ko': No such file or directory
NET: Registered protocol family 15
Initializing XFRM netlink socket
/proc/sys/vfs_c
Now flash open!
(none) mips #3 Fri Jun 28 10:10:08 CST 2013 (none)
(none) login: Now flash open!
ATHR_GMAC: Length per segment 1536
ATHR_GMAC: fifo cfg 3 01f00140
ATHR_GMAC: RX TASKLET - Pkts per Intr:32
mac:1 Registering S27....
ATHR_GMAC: Max segments per packet :   1
ATHR_GMAC: Max tx descriptor count :   40
ATHR_GMAC: Max rx descriptor count :   128
ATHR_GMAC: Mac capability flags    :   2D82
ATHR_GMAC: RX TASKLET - Pkts per Intr:32
mac:0 Registering S27....
ATHR_GMAC: Max segments per packet :   1
ATHR_GMAC: Max tx descriptor count :   40
ATHR_GMAC: Max rx descriptor count :   128
ATHR_GMAC: Mac capability flags    :   2582
athr_gmac_ring_alloc Allocated 640 at 0x81ea6800
athr_gmac_ring_alloc Allocated 2048 at 0x81cb7000
WASP ----> S27 PHY MDIO
Setting Drop CRC Errors, Pause Frames and Length Error frames
ATHRS27: resetting s27
ATHRS27: s27 reset done
++++ athrs27_igmp_setup once
port0 vid is 0xb000b
port1 vid is 0x30003
port2 vid is 0x50005
port3 vid is 0x70007
port4 vid is 0x90009
++ PVID: 0x0000000b, bitmap: 0x0000001f
++ PVID: 0x00000003, bitmap: 0x0000001f
++ PVID: 0x00000005, bitmap: 0x0000001f
++ PVID: 0x00000007, bitmap: 0x0000001f
++ PVID: 0x00000009, bitmap: 0x0000001f
vtable vid: 0x00000002, bitmap 0x00000003
vtable vid: 0x00000004, bitmap 0x00000005
vtable vid: 0x00000006, bitmap 0x00000007
vtable vid: 0x00000008, bitmap 0x00000009
vtable vid: 0x0000000a, bitmap 0x0000000b
vtable vid: 0x0000000c, bitmap 0x0000000d
vtable vid: 0x0000000e, bitmap 0x0000000f
vtable vid: 0x00000010, bitmap 0x00000011
vtable vid: 0x00000012, bitmap 0x00000013
vtable vid: 0x00000014, bitmap 0x00000015
vtable vid: 0x00000016, bitmap 0x00000017
vtable vid: 0x00000018, bitmap 0x00000019
vtable vid: 0x0000001a, bitmap 0x0000001b
vtable vid: 0x0000001c, bitmap 0x0000001d
vtable vid: 0x0000001e, bitmap 0x0000001f
vtable vid: 0x00000020, bitmap 0x00000021
Setting PHY...
athr_gmac_ring_alloc Allocated 640 at 0x81ec6c00
athr_gmac_ring_alloc Allocated 2048 at 0x81e31000
WASP ----> S27 PHY MDIO
Setting Drop CRC Errors, Pause Frames and Length Error frames
Setting PHY...
device eth0 entered promiscuous mode
athr_gmac_ring_free Freeing at 0x81ec6c00
athr_gmac_ring_free Freeing at 0x81e31000
athr_gmac_ring_alloc Allocated 640 at 0x81ec6c00
athr_gmac_ring_alloc Allocated 2048 at 0x81f0d800
WASP ----> S27 PHY MDIO
Setting Drop CRC Errors, Pause Frames and Length Error frames
Setting PHY...
Now flash open!
athr_gmac_ring_free Freeing at 0x81ea6800
athr_gmac_ring_free Freeing at 0x81cb7000
athr_gmac_ring_alloc Allocated 640 at 0x81ea6800
athr_gmac_ring_alloc Allocated 2048 at 0x81e98800
WASP ----> S27 PHY MDIO
Setting Drop CRC Errors, Pause Frames and Length Error frames
Setting PHY...
nf_conntrack_rtsp v0.6.21 loading
nf_nat_rtsp v0.6.21 loading
asf: module license 'Proprietary' taints kernel.
Disabling lock debugging due to kernel taint
ath_hal: 0.9.17.1 (AR5416, AR9380, REGOPS_FUNC, WRITE_EEPROM, 11D)
ath_rate_atheros: Copyright (c) 2001-2005 Atheros Communications, Inc, All Rights Reserved
ath_dev: Copyright (c) 2001-2007 Atheros Communications, Inc, All Rights Reserved
ath_ahb: 9.2.0_U10.1020 (Atheros/multi-bss)
__ath_attach: Set global_scn[0]
ACBKMinfree = 48
ACBEMinfree = 32
ACVIMinfree = 16
ACVOMinfree = 0
CABMinfree = 48
UAPSDMinfree = 0
Restoring Cal data from Flash
ath_get_caps[5113] rx chainmask mismatch actual 3 sc_chainmak 0
ath_get_caps[5088] tx chainmask mismatch actual 3 sc_chainmak 0
wifi0: Atheros 9340: mem=0xb8100000, irq=2
wlan_vap_create : enter. devhandle=0x80c1c2c0, opmode=IEEE80211_M_HOSTAP, flags=0x1
wlan_vap_create : exit. devhandle=0x80c1c2c0, opmode=IEEE80211_M_HOSTAP, flags=0x1.
VAP device ath0 created


***********************************

DES SSID SET=TP-LINK_AFCC16
ieee80211_ioctl_siwmode: imr.ifm_active=131712, new mode=3, valid=1


***********************************
athr_gmac_ring_free Freeing at 0x81ea6800
athr_gmac_ring_free Freeing at 0x81e98800
br0: port 1(eth0) entering disabled state
athr_gmac_ring_alloc Allocated 640 at 0x81ea6800
athr_gmac_ring_alloc Allocated 2048 at 0x81e98000
WASP ----> S27 PHY MDIO
Setting Drop CRC Errors, Pause Frames and Length Error frames
Setting PHY...


***********************************
device ath0 entered promiscuous mode
br0: port 2(ath0) entering forwarding state
ieee80211_ioctl_siwmode: imr.ifm_active=1442432, new mode=3, valid=1
br0: port 2(ath0) entering disabled state

DES SSID SET=TP-LINK_AFCC16


***********************************
br0: port 2(ath0) entering forwarding state
fuse init (API version 7.12)
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
Port Status 1c000004
ath-ehci ath-ehci.0: ATH EHCI
ath-ehci ath-ehci.0: new USB bus registered, assigned bus number 1
ehci_reset Intialize USB CONTROLLER in host mode: 13
ehci_reset Port Status 1c000000
ath-ehci ath-ehci.0: irq 3, io mem 0x1b000000
ehci_reset Intialize USB CONTROLLER in host mode: 13
ehci_reset Port Status 1c000000
ath-ehci ath-ehci.0: USB 2.0 started, EHCI 1.00
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
SCSI subsystem initialized
usb 1-1: new high speed USB device using ath-ehci and address 2
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
usb 1-1: configuration #1 chosen from 1 choice
scsi0 : SCSI emulation for USB Mass Storage devices
kcg 323 :GPL NetUSB up!
kc   90 : run_telnetDBGDServer start
kc  227 : init_DebugD end
INFO17B7: NetUSB 1.02.29, 0002061F : Dec 11 2012 10:20:50
INFO17B9:  AUTH ISOC
INFO17BA:  filterAudio
usbcore: registered new interface driver KC NetUSB General Driver
INFO0110:  init proc : PAGE_SIZE 4096
INFO1819: Check mac address
INFO168B:  infomap c0f5bf20
INFO168E:  sleep to wait br0 to wake up
INFO02D0:  use dev Name br0
INFO1697:  sleep to wait br0 end.
INFO16B0:  UDP_BROAD 7437 tcpPort:625868800
INFO02D0:  use dev Name br0
INFO1597: tcpConnector() started...
ATHR_GMAC: GE0 RX DMA ENABLE
INFO1474: Bind to br0
scsi 0:0:0:0: Direct-Access     Netac    OnlyDisk         PMAP PQ: 0 ANSI: 6
sd 0:0:0:0: [sda] 31326208 512-byte logical blocks: (16.0 GB/14.9 GiB)
sd 0:0:0:0: Attached scsi generic sg0 type 0
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Assuming drive cache: write through
sd 0:0:0:0: [sda] Assuming drive cache: write through
sda: sda1
SQUASHFS error: Can't find a SQUASHFS superblock on sda
FAT: utf8 is not a recommended IO charset for FAT filesystems, filesystem will be case sensitive!
sd 0:0:0:0: [sda] Assuming drive cache: write through
sd 0:0:0:0: [sda] Attached SCSI removable disk
FAT: invalid media value (0xb9)
VFS: Can't find a valid FAT filesystem on dev sda.
SQUASHFS error: Can't find a SQUASHFS superblock on sda1
FAT: utf8 is not a recommended IO charset for FAT filesystems, filesystem will be case sensitive!
Now flash open!
Erase from 0X7E0000 to 0X7EB124:.
Program from 0X7E0000 to 0X7EB124:
write successfully
Now flash open!
Erase from 0X7E0000 to 0X7EB124:.
Program from 0X7E0000 to 0X7EB124:
write successfully
Now flash open!
Erase from 0X7E0000 to 0X7EB124:.
Program from 0X7E0000 to 0X7EB124:
write successfully
usb 1-1: USB disconnect, address 2
FAT: bread failed in fat_clusters_flush
FAT: bread failed in fat_clusters_flush
Now flash open!
Erase from 0X7E0000 to 0X7EB124:.
Program from 0X7E0000 to 0X7EB124:
write successfully
usb 1-1: new high speed USB device using ath-ehci and address 3
usb 1-1: configuration #1 chosen from 1 choice
scsi1 : SCSI emulation for USB Mass Storage devices
scsi 1:0:0:0: Direct-Access     Netac    OnlyDisk         PMAP PQ: 0 ANSI: 6
sd 1:0:0:0: [sda] 31326208 512-byte logical blocks: (16.0 GB/14.9 GiB)
sd 1:0:0:0: Attached scsi generic sg0 type 0
sd 1:0:0:0: [sda] Write Protect is off
sd 1:0:0:0: [sda] Assuming drive cache: write through
sd 1:0:0:0: [sda] Assuming drive cache: write through
sda: sda1
sd 1:0:0:0: [sda] Assuming drive cache: write through
sd 1:0:0:0: [sda] Attached SCSI removable disk
SQUASHFS error: Can't find a SQUASHFS superblock on sda
FAT: utf8 is not a recommended IO charset for FAT filesystems, filesystem will be case sensitive!
FAT: invalid media value (0xb9)
VFS: Can't find a valid FAT filesystem on dev sda.
SQUASHFS error: Can't find a SQUASHFS superblock on sda1
FAT: utf8 is not a recommended IO charset for FAT filesystems, filesystem will be case sensitive!
usb 1-1: USB disconnect, address 3
sd 1:0:0:0: [sda] Unhandled error code
sd 1:0:0:0: [sda] Result: hostbyte=0x07 driverbyte=0x00
end_request: I/O error, dev sda, sector 11338
sd 1:0:0:0: [sda] Unhandled error code
sd 1:0:0:0: [sda] Result: hostbyte=0x07 driverbyte=0x00
end_request: I/O error, dev sda, sector 11339
sd 1:0:0:0: [sda] Unhandled error code
sd 1:0:0:0: [sda] Result: hostbyte=0x01 driverbyte=0x00
end_request: I/O error, dev sda, sector 11340
FAT: FAT read failed (blocknr 3274)
FAT: FAT read failed (blocknr 3274)
Now flash open!
Erase from 0X7E0000 to 0X7EB124:.
Program from 0X7E0000 to 0X7EB124:
write successfully
usb 1-1: new high speed USB device using ath-ehci and address 4
usb 1-1: configuration #1 chosen from 1 choice
scsi2 : SCSI emulation for USB Mass Storage devices
FAT: bread failed in fat_clusters_flush
FAT: bread failed in fat_clusters_flush
Now flash open!
Erase from 0X7E0000 to 0X7EB124:.
Program from 0X7E0000 to 0X7EB124:
write successfully
Now flash open!
Erase from 0X7E0000 to 0X7EB124:.
Program from 0X7E0000 to 0X7EB124:
write successfully
usb 1-1: USB disconnect, address 4
usb 1-1: new high speed USB device using ath-ehci and address 5
usb 1-1: configuration #1 chosen from 1 choice
scsi3 : SCSI emulation for USB Mass Storage devices
scsi 3:0:0:0: Direct-Access     Netac    OnlyDisk         PMAP PQ: 0 ANSI: 6
sd 3:0:0:0: Attached scsi generic sg0 type 0
sd 3:0:0:0: [sda] 31326208 512-byte logical blocks: (16.0 GB/14.9 GiB)
sd 3:0:0:0: [sda] Write Protect is off
sd 3:0:0:0: [sda] Assuming drive cache: write through
sd 3:0:0:0: [sda] Assuming drive cache: write through
sda: sda1
sd 3:0:0:0: [sda] Assuming drive cache: write through
sd 3:0:0:0: [sda] Attached SCSI removable disk
SQUASHFS error: Can't find a SQUASHFS superblock on sda
FAT: utf8 is not a recommended IO charset for FAT filesystems, filesystem will be case sensitive!
FAT: invalid media value (0xb9)
VFS: Can't find a valid FAT filesystem on dev sda.
SQUASHFS error: Can't find a SQUASHFS superblock on sda1
FAT: utf8 is not a recommended IO charset for FAT filesystems, filesystem will be case sensitive!
usb 1-1: USB disconnect, address 5
sd 3:0:0:0: [sda] Unhandled error code
sd 3:0:0:0: [sda] Result: hostbyte=0x07 driverbyte=0x00
end_request: I/O error, dev sda, sector 10761
sd 3:0:0:0: [sda] Unhandled error code
sd 3:0:0:0: [sda] Result: hostbyte=0x07 driverbyte=0x00
end_request: I/O error, dev sda, sector 10762
sd 3:0:0:0: [sda] Unhandled error code
sd 3:0:0:0: [sda] Result: hostbyte=0x01 driverbyte=0x00
end_request: I/O error, dev sda, sector 10763
FAT: FAT read failed (blocknr 2697)
FAT: FAT read failed (blocknr 2697)
usb 1-1: new high speed USB device using ath-ehci and address 6
usb 1-1: configuration #1 chosen from 1 choice
scsi4 : SCSI emulation for USB Mass Storage devices
FAT: bread failed in fat_clusters_flush
FAT: bread failed in fat_clusters_flush
Now flash open!
Erase from 0X7E0000 to 0X7EB124:.
Program from 0X7E0000 to 0X7EB124:
write successfully
Now flash open!
Erase from 0X7E0000 to 0X7EB124:.
Program from 0X7E0000 to 0X7EB124:
write successfully
scsi 4:0:0:0: Direct-Access     Netac    OnlyDisk         PMAP PQ: 0 ANSI: 6
sd 4:0:0:0: Attached scsi generic sg0 type 0
sd 4:0:0:0: [sda] 31326208 512-byte logical blocks: (16.0 GB/14.9 GiB)
sd 4:0:0:0: [sda] Write Protect is off
sd 4:0:0:0: [sda] Assuming drive cache: write through
sd 4:0:0:0: [sda] Assuming drive cache: write through
sda: sda1
sd 4:0:0:0: [sda] Assuming drive cache: write through
sd 4:0:0:0: [sda] Attached SCSI removable disk
SQUASHFS error: Can't find a SQUASHFS superblock on sda
FAT: utf8 is not a recommended IO charset for FAT filesystems, filesystem will be case sensitive!
FAT: invalid media value (0xb9)
VFS: Can't find a valid FAT filesystem on dev sda.
SQUASHFS error: Can't find a SQUASHFS superblock on sda1
FAT: utf8 is not a recommended IO charset for FAT filesystems, filesystem will be case sensitive!
Now flash open!
Erase from 0X7E0000 to 0X7EB124:.
Program from 0X7E0000 to 0X7EB124:
write successfully
Now flash open!
Erase from 0X7E0000 to 0X7EB124:.
Program from 0X7E0000 to 0X7EB124:
write successfully
Now flash open!
Erase from 0X7E0000 to 0X7EB124:.
Program from 0X7E0000 to 0X7EB124:
write successfully
usb 1-1: USB disconnect, address 6
FAT: bread failed in fat_clusters_flush
FAT: bread failed in fat_clusters_flush
Now flash open!
Erase from 0X7E0000 to 0X7EB124:.
Program from 0X7E0000 to 0X7EB124:
write successfully
usb 1-1: new high speed USB device using ath-ehci and address 7
usb 1-1: configuration #1 chosen from 1 choice
scsi5 : SCSI emulation for USB Mass Storage devices
scsi 5:0:0:0: Direct-Access     Netac    OnlyDisk         PMAP PQ: 0 ANSI: 6
sd 5:0:0:0: [sda] 31326208 512-byte logical blocks: (16.0 GB/14.9 GiB)
sd 5:0:0:0: Attached scsi generic sg0 type 0
sd 5:0:0:0: [sda] Write Protect is off
sd 5:0:0:0: [sda] Assuming drive cache: write through
sd 5:0:0:0: [sda] Assuming drive cache: write through
sda: sda1
sd 5:0:0:0: [sda] Assuming drive cache: write through
sd 5:0:0:0: [sda] Attached SCSI removable disk
SQUASHFS error: Can't find a SQUASHFS superblock on sda
FAT: utf8 is not a recommended IO charset for FAT filesystems, filesystem will be case sensitive!
FAT: invalid media value (0xb9)
VFS: Can't find a valid FAT filesystem on dev sda.
SQUASHFS error: Can't find a SQUASHFS superblock on sda1
FAT: utf8 is not a recommended IO charset for FAT filesystems, filesystem will be case sensitive!
Now flash open!
Erase from 0X7E0000 to 0X7EB124:.
Program from 0X7E0000 to 0X7EB124:
write successfully
Now flash open!
Erase from 0X7E0000 to 0X7EB124:.
Program from 0X7E0000 to 0X7EB124:
write successfully
Now flash open!
Erase from 0X7E0000 to 0X7EB124:.
Program from 0X7E0000 to 0X7EB124:
write successfully
usb 1-1: USB disconnect, address 7
FAT: bread failed in fat_clusters_flush
FAT: bread failed in fat_clusters_flush
usb 1-1: new high speed USB device using ath-ehci and address 8
usb 1-1: configuration #1 chosen from 1 choice
scsi6 : SCSI emulation for USB Mass Storage devices
Now flash open!
Erase from 0X7E0000 to 0X7EB124:.
Program from 0X7E0000 to 0X7EB124:
write successfully
usb 1-1: USB disconnect, address 8
usb 1-1: new high speed USB device using ath-ehci and address 9
usb 1-1: configuration #1 chosen from 1 choice
scsi7 : SCSI emulation for USB Mass Storage devices
usb 1-1: USB disconnect, address 9
usb 1-1: new high speed USB device using ath-ehci and address 10
usb 1-1: configuration #1 chosen from 1 choice
scsi8 : SCSI emulation for USB Mass Storage devices
scsi 8:0:0:0: Direct-Access     Netac    OnlyDisk         PMAP PQ: 0 ANSI: 6
sd 8:0:0:0: Attached scsi generic sg0 type 0
sd 8:0:0:0: [sda] 31326208 512-byte logical blocks: (16.0 GB/14.9 GiB)
sd 8:0:0:0: [sda] Write Protect is off
sd 8:0:0:0: [sda] Assuming drive cache: write through
sd 8:0:0:0: [sda] Assuming drive cache: write through
sda: sda1
sd 8:0:0:0: [sda] Assuming drive cache: write through
sd 8:0:0:0: [sda] Attached SCSI removable disk
SQUASHFS error: Can't find a SQUASHFS superblock on sda
FAT: utf8 is not a recommended IO charset for FAT filesystems, filesystem will be case sensitive!
FAT: invalid media value (0xb9)
VFS: Can't find a valid FAT filesystem on dev sda.
SQUASHFS error: Can't find a SQUASHFS superblock on sda1
FAT: utf8 is not a recommended IO charset for FAT filesystems, filesystem will be case sensitive!
Now flash open!
Erase from 0X7E0000 to 0X7EB124:.
Program from 0X7E0000 to 0X7EB124:
write successfully
Now flash open!
Erase from 0X7E0000 to 0X7EB124:.
Program from 0X7E0000 to 0X7EB124:
write successfully
Now flash open!
Erase from 0X7E0000 to 0X7EB124:.
Program from 0X7E0000 to 0X7EB124:
write successfully
usb 1-1: USB disconnect, address 10
FAT: bread failed in fat_clusters_flush
FAT: bread failed in fat_clusters_flush
usb 1-1: new high speed USB device using ath-ehci and address 11
usb 1-1: configuration #1 chosen from 1 choice
scsi9 : SCSI emulation for USB Mass Storage devices
Now flash open!
Erase from 0X7E0000 to 0X7EB124:.
Program from 0X7E0000 to 0X7EB124:
write successfully

800nV1刷9341通用breed+842NDV2固件,挂了u盘,启动没问题,就是电脑无线(有线没有问题)连接路由,就出现u盘就掉了

点评

刷了明月的op 还是不能 无线连接路由,一连接就这样 DRAM: 32MB Platform: Atheros AR9341 rev 3 Board: Atheros AP123 reference board Clocks: CPU: 560MHz, DDR: 400MHz, AHB: 200MHz, Ref: 25MHz Flash:  详情 回复 发表于 2015-10-26 22:55
刷了明月的op 还是不能 无线连接路由,一连接就这样 DRAM: 32MB Platform: Atheros AR9341 rev 3 Board: Atheros AP123 reference board Clocks: CPU: 560MHz, DDR: 400MHz, AHB: 200MHz, Ref: 25MHz Flash:  详情 回复 发表于 2015-10-26 22:54
我的恩山、我的无线 The best wifi forum is right here.
发表于 2015-10-26 22:49 | 显示全部楼层
老大,支持一下8196c吧,造福一下坛友啊,这货用的也挺多的
我的恩山、我的无线 The best wifi forum is right here.
发表于 2015-10-26 22:54 | 显示全部楼层
smilemoon 发表于 2015-10-26 21:27
Restarting system.

Boot and Recovery Environment for Embedded Devices

刷了明月的op 还是不能 无线连接路由,一连接就这样

DRAM: 32MB
Platform: Atheros AR9341 rev 3
Board: Atheros AP123 reference board
Clocks: CPU: 560MHz, DDR: 400MHz, AHB: 200MHz, Ref: 25MHz
Flash: Winbond W25Q64 (8MB) on ath79-spi
ag71xx-eth: Using MAC address 0c:82:68:af:cc:16
eth0: Atheros AR8228/AR8229 rev 1

Network started on eth0, inet addr 192.168.1.1, netmask 255.255.255.0

Press any key to interrupt autoboot ... 3   
Autoboot aborted due to Breed Enter.

Starting breed built-in shell

breed> Upgrade completed.
Rebooting in 2 seconds ...
Resetting ...
Boot and Recovery Environment for Embedded Devices
Copyright (C) 2015 HackPascal <[email protected]>
Build date 2015-10-18 [git-bb5218f]
Version 1.0 (r777)

DRAM: 32MB
Platform: Atheros AR9341 rev 3
Board: Atheros AP123 reference board
Clocks: CPU: 560MHz, DDR: 400MHz, AHB: 200MHz, Ref: 25MHz
Flash: Winbond W25Q64 (8MB) on ath79-spi
ag71xx-eth: Using MAC address 0c:82:68:af:cc:16
eth0: Atheros AR8228/AR8229 rev 1

Network started on eth0, inet addr 192.168.1.1, netmask 255.255.255.0

Press any key to interrupt autoboot ... 0   

Trying to boot firmware from 0x9f020000 ...
TP-LINK firmware image header detected.
    Image Name:   08420002
    Data Size:    1064028 Bytes
    Load Address: 80060000
    Entry Point:  80060000
Uncompressing data (LZMA) ... done.
Flushing cache ... done.

Starting kernel at 0x80060000...

[    0.000000] Linux version 3.10.70 ([email protected]) (gcc version 4.8.3 (OpenWrt/Linaro GCC 4.8-2014.04 r44550) ) #3 Sat Mar 7 01:21:49 CST 2015
[    0.000000] bootconsole [early0] enabled
[    0.000000] CPU revision is: 0001974c (MIPS 74Kc)
[    0.000000] SoC: Atheros AR9341 rev 3
[    0.000000] Clocks: CPU:560.000MHz, DDR:400.000MHz, AHB:200.000MHz, Ref:25.000MHz
[    0.000000] Determined physical RAM map:
[    0.000000]  memory: 02000000 @ 00000000 (usable)
[    0.000000] Initrd not found or empty - disabling initrd
[    0.000000] Zone ranges:
[    0.000000]   Normal   [mem 0x00000000-0x01ffffff]
[    0.000000] Movable zone start for each node
[    0.000000] Early memory node ranges
[    0.000000]   node   0: [mem 0x00000000-0x01ffffff]
[    0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
[    0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 8128
[    0.000000] Kernel command line:  board=TL-WR842N-v2 console=ttyS0,115200 rootfstype=squashfs,jffs2 noinitrd
[    0.000000] PID hash table entries: 128 (order: -3, 512 bytes)
[    0.000000] Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)
[    0.000000] Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)
[    0.000000] Writing ErrCtl register=000000c0
[    0.000000] Readback ErrCtl register=000000c0
[    0.000000] Memory: 28720k/32768k available (2257k kernel code, 4048k reserved, 600k data, 276k init, 0k highmem)
[    0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[    0.000000] NR_IRQS:51
[    0.000000] Calibrating delay loop... 278.93 BogoMIPS (lpj=1394688)
[    0.070000] pid_max: default: 32768 minimum: 301
[    0.070000] Mount-cache hash table entries: 512
[    0.080000] NET: Registered protocol family 16
[    0.090000] MIPS: machine is TP-LINK TL-WR842N/ND v2
[    0.510000] bio: create slab <bio-0> at 0
[    0.510000] Switching to clocksource MIPS
[    0.520000] NET: Registered protocol family 2
[    0.520000] TCP established hash table entries: 512 (order: 0, 4096 bytes)
[    0.530000] TCP bind hash table entries: 512 (order: -1, 2048 bytes)
[    0.540000] TCP: Hash tables configured (established 512 bind 512)
[    0.540000] TCP: reno registered
[    0.550000] UDP hash table entries: 256 (order: 0, 4096 bytes)
[    0.550000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[    0.560000] NET: Registered protocol family 1
[    0.580000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    0.590000] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[    0.600000] msgmni has been set to 56
[    0.600000] io scheduler noop registered
[    0.610000] io scheduler deadline registered (default)
[    0.610000] Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled
[    0.640000] serial8250.0: ttyS0 at MMIO 0x18020000 (irq = 11) is a 16550A
[    0.650000] console [ttyS0] enabled, bootconsole disabled
[    0.650000] console [ttyS0] enabled, bootconsole disabled
[    0.660000] ath79-spi ath79-spi: master is unqueued, this is deprecated
[    0.670000] m25p80 spi0.0: found w25q64, expected m25p80
[    0.670000] m25p80 spi0.0: w25q64 (8192 Kbytes)
[    0.680000] 6 tp-link partitions found on MTD device spi0.0
[    0.690000] Creating 6 MTD partitions on "spi0.0":
[    0.690000] 0x000000000000-0x000000020000 : "u-boot"
[    0.700000] 0x000000020000-0x000000123e5c : "kernel"
[    0.700000] mtd: partition "kernel" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
[    0.720000] 0x000000123e5c-0x0000007f0000 : "rootfs"
[    0.720000] mtd: partition "rootfs" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
[    0.740000] mtd: device 2 (rootfs) set to be root filesystem
[    0.740000] 1 squashfs-split partitions found on MTD device rootfs
[    0.750000] 0x000000760000-0x0000007f0000 : "rootfs_data"
[    0.760000] 0x0000007f0000-0x000000800000 : "art"
[    0.760000] 0x000000020000-0x0000007f0000 : "firmware"
[    0.770000] 0x000000000000-0x000000800000 : "fullflash"
[    0.790000] libphy: ag71xx_mdio: probed
[    1.350000] ag71xx ag71xx.0: connected to PHY at ag71xx-mdio.1:04 [uid=004dd042, driver=Generic PHY]
[    1.360000] eth0: Atheros AG71xx at 0xb9000000, irq 4, mode:MII
[    1.920000] ag71xx-mdio.1: Found an AR934X built-in switch
[    2.950000] eth1: Atheros AG71xx at 0xba000000, irq 5, mode:GMII
[    2.960000] TCP: cubic registered
[    2.960000] NET: Registered protocol family 17
[    2.970000] Bridge firewalling registered
[    2.970000] 8021q: 802.1Q VLAN Support v1.8
[    2.980000] VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
[    2.990000] Freeing unused kernel memory: 276K (8032b000 - 80370000)
procd: Console is alive
procd: - watchdog -
[    7.480000] usbcore: registered new interface driver usbfs
[    7.480000] usbcore: registered new interface driver hub
[    7.490000] usbcore: registered new device driver usb
[    7.540000] SCSI subsystem initialized
[    7.550000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    7.560000] ehci-platform: EHCI generic platform driver
[    7.560000] ehci-platform ehci-platform: EHCI Host Controller
[    7.570000] ehci-platform ehci-platform: new USB bus registered, assigned bus number 1
[    7.580000] ehci-platform ehci-platform: TX-TX IDP fix enabled
[    7.590000] ehci-platform ehci-platform: irq 3, io mem 0x1b000000
[    7.610000] ehci-platform ehci-platform: USB 2.0 started, EHCI 1.00
[    7.610000] hub 1-0:1.0: USB hub found
[    7.620000] hub 1-0:1.0: 1 port detected
[    7.620000] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[    7.630000] uhci_hcd: USB Universal Host Controller Interface driver
[    7.640000] usbcore: registered new interface driver usb-storage
procd: - preinit -
[    8.210000] usb 1-1: new high-speed USB device number 2 using ehci-platform
[    8.360000] usb-storage 1-1:1.0: USB Mass Storage device detected
[    8.370000] scsi0 : usb-storage 1-1:1.0
Press the [f] key and hit [enter] to enter failsafe mode
Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level
[    9.430000] scsi 0:0:0:0: Direct-Access     Netac    OnlyDisk         PMAP PQ: 0 ANSI: 6
[   10.190000] sd 0:0:0:0: [sda] 31326208 512-byte logical blocks: (16.0 GB/14.9 GiB)
[   10.200000] sd 0:0:0:0: [sda] Write Protect is off
[   10.200000] sd 0:0:0:0: [sda] No Caching mode page found
[   10.210000] sd 0:0:0:0: [sda] Assuming drive cache: write through
[   10.220000] sd 0:0:0:0: [sda] No Caching mode page found
[   10.220000] sd 0:0:0:0: [sda] Assuming drive cache: write through
[   10.250000]  sda: sda1
[   10.260000] sd 0:0:0:0: [sda] No Caching mode page found
[   10.260000] sd 0:0:0:0: [sda] Assuming drive cache: write through
[   10.270000] sd 0:0:0:0: [sda] Attached SCSI removable disk
block: extroot: failed to load /etc/config/fstab: Entry not found
jffs2 is not ready - marker found
procd: - early -
procd: - watchdog -
procd: - ubus -
procd: - init -
Please press Enter to activate this console.
[   19.580000] NET: Registered protocol family 8
[   19.580000] NET: Registered protocol family 20
[   19.600000] tun: Universal TUN/TAP device driver, 1.6
[   19.600000] tun: (C) 1999-2004 Max Krasnyansky <[email protected]>
[   19.620000] l2tp_core: L2TP core driver, V2.0
[   19.620000] l2tp_netlink: L2TP netlink interface
[   19.640000] gre: GRE over IPv4 demultiplexor driver
[   19.640000] ip_gre: GRE over IPv4 tunneling driver
[   19.660000] PPP generic driver version 2.4.2
[   19.670000]  Hooked IMQ after mangle on PREROUTING
[   19.680000]  Hooked IMQ after nat on POSTROUTING
[   19.680000] IMQ driver loaded successfully. (numdevs = 2, numqueues = 1)
[   19.690000]  Hooking IMQ before NAT on PREROUTING.
[   19.700000]  Hooking IMQ after NAT on POSTROUTING.
[   19.710000] Netfilter messages via NETLINK v0.30.
[   19.710000] ip_set: protocol 6
[   19.760000] ufsd: module license 'Commercial product' taints kernel.
[   19.760000] Disabling lock debugging due to kernel taint
[   19.790000] ufsd:: trace mask set to 0000000f
[   19.790000] ufsd: driver (lke_8.9.0 lke_8.9.0_22, LBD=ON, delalloc, ioctl, bdi, sd2, fua, tr) loaded at 80400000
[   19.790000] NTFS support included
[   19.790000] Big endian platform
[   19.790000] optimized: speed
[   19.790000] Build_for__ASUS_PRODUCTS_005_k2.6.22.15_2013-11-20_lke_8.9.0_r217400_b3
[   19.790000]
[   19.830000] u32 classifier
[   19.840000]     input device check on
[   19.840000]     Actions configured
[   19.850000] Mirror/redirect action on
[   19.860000] nf_conntrack version 0.5.0 (453 buckets, 1812 max)
[   19.870000] Failed to load ipt action
[   19.910000] fuse init (API version 7.22)
[   19.920000] arp_tables: (C) 2002 David S. Miller
[   19.930000] Loading modules backported from Linux version master-2014-05-22-0-gf2032ea
[   19.940000] Backport generated by backports.git backports-20140320-37-g5c33da0
[   19.980000] Ebtables v2.0 registered
[   20.000000] ip_tables: (C) 2000-2006 Netfilter Core Team
[   20.080000] PPP MPPE Compression module registered
[   20.100000] NET: Registered protocol family 24
[   20.100000] PPTP driver version 0.8.5
[   20.120000] usbcore: registered new interface driver ums-alauda
[   20.140000] usbcore: registered new interface driver ums-cypress
[   20.160000] usbcore: registered new interface driver ums-datafab
[   20.170000] usbcore: registered new interface driver ums-freecom
[   20.170000] usbcore: registered new interface driver ums-isd200
[   20.190000] usbcore: registered new interface driver ums-jumpshot
[   20.210000] usbcore: registered new interface driver ums-karma
[   20.230000] usbcore: registered new interface driver ums-sddr09
[   20.240000] usbcore: registered new interface driver ums-sddr55
[   20.240000] usbcore: registered new interface driver ums-usbat
[   20.380000] xt_time: kernel timezone is -0000
[   20.460000] cfg80211: Calling CRDA to update world regulatory domain
[   20.460000] cfg80211: World regulatory domain updated:
[   20.470000] cfg80211:  DFS Master region: unset
[   20.470000] cfg80211:   (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time)
[   20.480000] cfg80211:   (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
[   20.490000] cfg80211:   (2457000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
[   20.500000] cfg80211:   (2474000 KHz - 2494000 KHz @ 20000 KHz), (N/A, 2000 mBm), (N/A)
[   20.510000] cfg80211:   (5170000 KHz - 5250000 KHz @ 160000 KHz), (N/A, 2000 mBm), (N/A)
[   20.520000] cfg80211:   (5250000 KHz - 5330000 KHz @ 160000 KHz), (N/A, 2000 mBm), (0 s)
[   20.530000] cfg80211:   (5490000 KHz - 5730000 KHz @ 160000 KHz), (N/A, 2000 mBm), (0 s)
[   20.530000] cfg80211:   (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A)
[   20.540000] cfg80211:   (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 0 mBm), (N/A)
[   20.560000] l2tp_ppp: PPPoL2TP kernel driver, V2.0
[   20.740000] usbcore: registered new interface driver rtl8187
[   22.320000] usbcore: registered new interface driver rt2800usb
[   23.180000] cfg80211: Calling CRDA for country: US
[   23.200000] cfg80211: Regulatory domain changed to country: US
[   23.200000] cfg80211:  DFS Master region: FCC
[   23.210000] cfg80211:   (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time)
[   23.220000] cfg80211:   (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 3000 mBm), (N/A)
[   23.220000] cfg80211:   (5170000 KHz - 5250000 KHz @ 80000 KHz), (N/A, 2700 mBm), (N/A)
[   23.230000] cfg80211:   (5250000 KHz - 5330000 KHz @ 80000 KHz), (N/A, 2700 mBm), (0 s)
[   23.240000] cfg80211:   (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 3000 mBm), (N/A)
[   23.250000] cfg80211:   (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 4000 mBm), (N/A)
[   23.260000] ieee80211 phy0: Atheros AR9340 Rev:0 mem=0xb8100000, irq=47
[   48.010000] device eth1 entered promiscuous mode
[   52.420000] device wlan0 entered promiscuous mode
[   52.420000] br-lan: port 2(wlan0) entered forwarding state
[   52.430000] br-lan: port 2(wlan0) entered forwarding state
[   52.800000] eth0: link up (100Mbps/Full duplex)
[   52.800000] br-lan: port 2(wlan0) entered disabled state
[   55.930000] br-lan: port 2(wlan0) entered forwarding state
[   55.930000] br-lan: port 2(wlan0) entered forwarding state
[   57.930000] br-lan: port 2(wlan0) entered forwarding state
[   73.500000] eth0: link down
[   85.280000] jffs2_scan_eraseblock(): End of filesystem marker found at 0x0
[   85.310000] jffs2_build_filesystem(): unlocking the mtd device... done.
[   85.310000] jffs2_build_filesystem(): erasing all blocks after the end marker... done.
[   87.740000] jffs2: notice: (2699) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found.
[   89.790000] usb 1-1: USB disconnect, device number 2
[   90.110000] usb 1-1: new high-speed USB device number 3 using ehci-platform
[   90.270000] usb-storage 1-1:1.0: USB Mass Storage device detected
[   90.270000] scsi1 : usb-storage 1-1:1.0
[   91.290000] scsi 1:0:0:0: Direct-Access     Netac    OnlyDisk         PMAP PQ: 0 ANSI: 6
[   91.690000] sd 1:0:0:0: [sda] 31326208 512-byte logical blocks: (16.0 GB/14.9 GiB)
[   91.720000] sd 1:0:0:0: [sda] Write Protect is off
[   91.720000] sd 1:0:0:0: [sda] Mode Sense: 23 00 00 00
[   91.750000] sd 1:0:0:0: [sda] No Caching mode page found
[   91.750000] sd 1:0:0:0: [sda] Assuming drive cache: write through
[   91.780000] sd 1:0:0:0: [sda] No Caching mode page found
[   91.790000] sd 1:0:0:0: [sda] Assuming drive cache: write through
[   91.820000]  sda: sda1
[   91.830000] sd 1:0:0:0: [sda] No Caching mode page found
[   91.840000] sd 1:0:0:0: [sda] Assuming drive cache: write through
[   91.840000] sd 1:0:0:0: [sda] Attached SCSI removable disk
[   97.100000] FAT-fs (sda1): Volume was not properly unmounted. Some data may be corrupt. Please run fsck.
procd: - init complete -
[  134.140000] usb 1-1: USB disconnect, device number 3
[  134.440000] usb 1-1: new high-speed USB device number 4 using ehci-platform
[  134.600000] usb-storage 1-1:1.0: USB Mass Storage device detected
[  134.600000] scsi2 : usb-storage 1-1:1.0
[  135.150000] usb 1-1: USB disconnect, device number 4
[  135.450000] usb 1-1: new high-speed USB device number 5 using ehci-platform
[  135.600000] usb-storage 1-1:1.0: USB Mass Storage device detected
[  135.620000] scsi3 : usb-storage 1-1:1.0
[  136.620000] scsi 3:0:0:0: Direct-Access     Netac    OnlyDisk         PMAP PQ: 0 ANSI: 6
[  136.630000] sd 3:0:0:0: [sda] 31326208 512-byte logical blocks: (16.0 GB/14.9 GiB)
[  136.640000] sd 3:0:0:0: [sda] Write Protect is off
[  136.650000] sd 3:0:0:0: [sda] Mode Sense: 23 00 00 00
[  136.650000] sd 3:0:0:0: [sda] No Caching mode page found
[  136.660000] sd 3:0:0:0: [sda] Assuming drive cache: write through
[  136.670000] sd 3:0:0:0: [sda] No Caching mode page found
[  136.680000] sd 3:0:0:0: [sda] Assuming drive cache: write through
[  136.680000]  sda: sda1
[  136.700000] sd 3:0:0:0: [sda] No Caching mode page found
[  136.710000] sd 3:0:0:0: [sda] Assuming drive cache: write through
[  136.710000] sd 3:0:0:0: [sda] Attached SCSI removable disk
[  138.720000] FAT-fs (sda1): Volume was not properly unmounted. Some data may be corrupt. Please run fsck.
[  140.670000] usb 1-1: USB disconnect, device number 5
[  140.960000] usb 1-1: new high-speed USB device number 6 using ehci-platform
[  141.120000] usb-storage 1-1:1.0: USB Mass Storage device detected
[  141.120000] scsi4 : usb-storage 1-1:1.0
[  142.130000] scsi 4:0:0:0: Direct-Access     Netac    OnlyDisk         PMAP PQ: 0 ANSI: 6
[  142.140000] sd 4:0:0:0: [sda] 31326208 512-byte logical blocks: (16.0 GB/14.9 GiB)
[  142.150000] sd 4:0:0:0: [sda] Write Protect is off
[  142.160000] sd 4:0:0:0: [sda] Mode Sense: 23 00 00 00
[  142.160000] sd 4:0:0:0: [sda] No Caching mode page found
[  142.170000] sd 4:0:0:0: [sda] Assuming drive cache: write through
[  142.180000] sd 4:0:0:0: [sda] No Caching mode page found
[  142.190000] sd 4:0:0:0: [sda] Assuming drive cache: write through
[  142.190000]  sda: sda1
[  142.210000] sd 4:0:0:0: [sda] No Caching mode page found
[  142.220000] sd 4:0:0:0: [sda] Assuming drive cache: write through
[  142.220000] sd 4:0:0:0: [sda] Attached SCSI removable disk
[  143.330000] FAT-fs (sda1): Volume was not properly unmounted. Some data may be corrupt. Please run fsck.
我的恩山、我的无线 The best wifi forum is right here.
发表于 2015-10-26 22:55 | 显示全部楼层
smilemoon 发表于 2015-10-26 21:27
Restarting system.

Boot and Recovery Environment for Embedded Devices

刷了明月的op 还是不能 无线连接路由,一连接就这样

DRAM: 32MB
Platform: Atheros AR9341 rev 3
Board: Atheros AP123 reference board
Clocks: CPU: 560MHz, DDR: 400MHz, AHB: 200MHz, Ref: 25MHz
Flash: Winbond W25Q64 (8MB) on ath79-spi
ag71xx-eth: Using MAC address 0c:82:68:af:cc:16
eth0: Atheros AR8228/AR8229 rev 1

Network started on eth0, inet addr 192.168.1.1, netmask 255.255.255.0

Press any key to interrupt autoboot ... 3   
Autoboot aborted due to Breed Enter.

Starting breed built-in shell

breed> Upgrade completed.
Rebooting in 2 seconds ...
Resetting ...
Boot and Recovery Environment for Embedded Devices
Copyright (C) 2015 HackPascal <[email protected]>
Build date 2015-10-18 [git-bb5218f]
Version 1.0 (r777)

DRAM: 32MB
Platform: Atheros AR9341 rev 3
Board: Atheros AP123 reference board
Clocks: CPU: 560MHz, DDR: 400MHz, AHB: 200MHz, Ref: 25MHz
Flash: Winbond W25Q64 (8MB) on ath79-spi
ag71xx-eth: Using MAC address 0c:82:68:af:cc:16
eth0: Atheros AR8228/AR8229 rev 1

Network started on eth0, inet addr 192.168.1.1, netmask 255.255.255.0

Press any key to interrupt autoboot ... 0   

Trying to boot firmware from 0x9f020000 ...
TP-LINK firmware image header detected.
    Image Name:   08420002
    Data Size:    1064028 Bytes
    Load Address: 80060000
    Entry Point:  80060000
Uncompressing data (LZMA) ... done.
Flushing cache ... done.

Starting kernel at 0x80060000...

[    0.000000] Linux version 3.10.70 ([email protected]) (gcc version 4.8.3 (OpenWrt/Linaro GCC 4.8-2014.04 r44550) ) #3 Sat Mar 7 01:21:49 CST 2015
[    0.000000] bootconsole [early0] enabled
[    0.000000] CPU revision is: 0001974c (MIPS 74Kc)
[    0.000000] SoC: Atheros AR9341 rev 3
[    0.000000] Clocks: CPU:560.000MHz, DDR:400.000MHz, AHB:200.000MHz, Ref:25.000MHz
[    0.000000] Determined physical RAM map:
[    0.000000]  memory: 02000000 @ 00000000 (usable)
[    0.000000] Initrd not found or empty - disabling initrd
[    0.000000] Zone ranges:
[    0.000000]   Normal   [mem 0x00000000-0x01ffffff]
[    0.000000] Movable zone start for each node
[    0.000000] Early memory node ranges
[    0.000000]   node   0: [mem 0x00000000-0x01ffffff]
[    0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
[    0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 8128
[    0.000000] Kernel command line:  board=TL-WR842N-v2 console=ttyS0,115200 rootfstype=squashfs,jffs2 noinitrd
[    0.000000] PID hash table entries: 128 (order: -3, 512 bytes)
[    0.000000] Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)
[    0.000000] Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)
[    0.000000] Writing ErrCtl register=000000c0
[    0.000000] Readback ErrCtl register=000000c0
[    0.000000] Memory: 28720k/32768k available (2257k kernel code, 4048k reserved, 600k data, 276k init, 0k highmem)
[    0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[    0.000000] NR_IRQS:51
[    0.000000] Calibrating delay loop... 278.93 BogoMIPS (lpj=1394688)
[    0.070000] pid_max: default: 32768 minimum: 301
[    0.070000] Mount-cache hash table entries: 512
[    0.080000] NET: Registered protocol family 16
[    0.090000] MIPS: machine is TP-LINK TL-WR842N/ND v2
[    0.510000] bio: create slab <bio-0> at 0
[    0.510000] Switching to clocksource MIPS
[    0.520000] NET: Registered protocol family 2
[    0.520000] TCP established hash table entries: 512 (order: 0, 4096 bytes)
[    0.530000] TCP bind hash table entries: 512 (order: -1, 2048 bytes)
[    0.540000] TCP: Hash tables configured (established 512 bind 512)
[    0.540000] TCP: reno registered
[    0.550000] UDP hash table entries: 256 (order: 0, 4096 bytes)
[    0.550000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[    0.560000] NET: Registered protocol family 1
[    0.580000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    0.590000] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[    0.600000] msgmni has been set to 56
[    0.600000] io scheduler noop registered
[    0.610000] io scheduler deadline registered (default)
[    0.610000] Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled
[    0.640000] serial8250.0: ttyS0 at MMIO 0x18020000 (irq = 11) is a 16550A
[    0.650000] console [ttyS0] enabled, bootconsole disabled
[    0.650000] console [ttyS0] enabled, bootconsole disabled
[    0.660000] ath79-spi ath79-spi: master is unqueued, this is deprecated
[    0.670000] m25p80 spi0.0: found w25q64, expected m25p80
[    0.670000] m25p80 spi0.0: w25q64 (8192 Kbytes)
[    0.680000] 6 tp-link partitions found on MTD device spi0.0
[    0.690000] Creating 6 MTD partitions on "spi0.0":
[    0.690000] 0x000000000000-0x000000020000 : "u-boot"
[    0.700000] 0x000000020000-0x000000123e5c : "kernel"
[    0.700000] mtd: partition "kernel" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
[    0.720000] 0x000000123e5c-0x0000007f0000 : "rootfs"
[    0.720000] mtd: partition "rootfs" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
[    0.740000] mtd: device 2 (rootfs) set to be root filesystem
[    0.740000] 1 squashfs-split partitions found on MTD device rootfs
[    0.750000] 0x000000760000-0x0000007f0000 : "rootfs_data"
[    0.760000] 0x0000007f0000-0x000000800000 : "art"
[    0.760000] 0x000000020000-0x0000007f0000 : "firmware"
[    0.770000] 0x000000000000-0x000000800000 : "fullflash"
[    0.790000] libphy: ag71xx_mdio: probed
[    1.350000] ag71xx ag71xx.0: connected to PHY at ag71xx-mdio.1:04 [uid=004dd042, driver=Generic PHY]
[    1.360000] eth0: Atheros AG71xx at 0xb9000000, irq 4, mode:MII
[    1.920000] ag71xx-mdio.1: Found an AR934X built-in switch
[    2.950000] eth1: Atheros AG71xx at 0xba000000, irq 5, mode:GMII
[    2.960000] TCP: cubic registered
[    2.960000] NET: Registered protocol family 17
[    2.970000] Bridge firewalling registered
[    2.970000] 8021q: 802.1Q VLAN Support v1.8
[    2.980000] VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
[    2.990000] Freeing unused kernel memory: 276K (8032b000 - 80370000)
procd: Console is alive
procd: - watchdog -
[    7.480000] usbcore: registered new interface driver usbfs
[    7.480000] usbcore: registered new interface driver hub
[    7.490000] usbcore: registered new device driver usb
[    7.540000] SCSI subsystem initialized
[    7.550000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    7.560000] ehci-platform: EHCI generic platform driver
[    7.560000] ehci-platform ehci-platform: EHCI Host Controller
[    7.570000] ehci-platform ehci-platform: new USB bus registered, assigned bus number 1
[    7.580000] ehci-platform ehci-platform: TX-TX IDP fix enabled
[    7.590000] ehci-platform ehci-platform: irq 3, io mem 0x1b000000
[    7.610000] ehci-platform ehci-platform: USB 2.0 started, EHCI 1.00
[    7.610000] hub 1-0:1.0: USB hub found
[    7.620000] hub 1-0:1.0: 1 port detected
[    7.620000] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[    7.630000] uhci_hcd: USB Universal Host Controller Interface driver
[    7.640000] usbcore: registered new interface driver usb-storage
procd: - preinit -
[    8.210000] usb 1-1: new high-speed USB device number 2 using ehci-platform
[    8.360000] usb-storage 1-1:1.0: USB Mass Storage device detected
[    8.370000] scsi0 : usb-storage 1-1:1.0
Press the [f] key and hit [enter] to enter failsafe mode
Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level
[    9.430000] scsi 0:0:0:0: Direct-Access     Netac    OnlyDisk         PMAP PQ: 0 ANSI: 6
[   10.190000] sd 0:0:0:0: [sda] 31326208 512-byte logical blocks: (16.0 GB/14.9 GiB)
[   10.200000] sd 0:0:0:0: [sda] Write Protect is off
[   10.200000] sd 0:0:0:0: [sda] No Caching mode page found
[   10.210000] sd 0:0:0:0: [sda] Assuming drive cache: write through
[   10.220000] sd 0:0:0:0: [sda] No Caching mode page found
[   10.220000] sd 0:0:0:0: [sda] Assuming drive cache: write through
[   10.250000]  sda: sda1
[   10.260000] sd 0:0:0:0: [sda] No Caching mode page found
[   10.260000] sd 0:0:0:0: [sda] Assuming drive cache: write through
[   10.270000] sd 0:0:0:0: [sda] Attached SCSI removable disk
block: extroot: failed to load /etc/config/fstab: Entry not found
jffs2 is not ready - marker found
procd: - early -
procd: - watchdog -
procd: - ubus -
procd: - init -
Please press Enter to activate this console.
[   19.580000] NET: Registered protocol family 8
[   19.580000] NET: Registered protocol family 20
[   19.600000] tun: Universal TUN/TAP device driver, 1.6
[   19.600000] tun: (C) 1999-2004 Max Krasnyansky <[email protected]>
[   19.620000] l2tp_core: L2TP core driver, V2.0
[   19.620000] l2tp_netlink: L2TP netlink interface
[   19.640000] gre: GRE over IPv4 demultiplexor driver
[   19.640000] ip_gre: GRE over IPv4 tunneling driver
[   19.660000] PPP generic driver version 2.4.2
[   19.670000]  Hooked IMQ after mangle on PREROUTING
[   19.680000]  Hooked IMQ after nat on POSTROUTING
[   19.680000] IMQ driver loaded successfully. (numdevs = 2, numqueues = 1)
[   19.690000]  Hooking IMQ before NAT on PREROUTING.
[   19.700000]  Hooking IMQ after NAT on POSTROUTING.
[   19.710000] Netfilter messages via NETLINK v0.30.
[   19.710000] ip_set: protocol 6
[   19.760000] ufsd: module license 'Commercial product' taints kernel.
[   19.760000] Disabling lock debugging due to kernel taint
[   19.790000] ufsd:: trace mask set to 0000000f
[   19.790000] ufsd: driver (lke_8.9.0 lke_8.9.0_22, LBD=ON, delalloc, ioctl, bdi, sd2, fua, tr) loaded at 80400000
[   19.790000] NTFS support included
[   19.790000] Big endian platform
[   19.790000] optimized: speed
[   19.790000] Build_for__ASUS_PRODUCTS_005_k2.6.22.15_2013-11-20_lke_8.9.0_r217400_b3
[   19.790000]
[   19.830000] u32 classifier
[   19.840000]     input device check on
[   19.840000]     Actions configured
[   19.850000] Mirror/redirect action on
[   19.860000] nf_conntrack version 0.5.0 (453 buckets, 1812 max)
[   19.870000] Failed to load ipt action
[   19.910000] fuse init (API version 7.22)
[   19.920000] arp_tables: (C) 2002 David S. Miller
[   19.930000] Loading modules backported from Linux version master-2014-05-22-0-gf2032ea
[   19.940000] Backport generated by backports.git backports-20140320-37-g5c33da0
[   19.980000] Ebtables v2.0 registered
[   20.000000] ip_tables: (C) 2000-2006 Netfilter Core Team
[   20.080000] PPP MPPE Compression module registered
[   20.100000] NET: Registered protocol family 24
[   20.100000] PPTP driver version 0.8.5
[   20.120000] usbcore: registered new interface driver ums-alauda
[   20.140000] usbcore: registered new interface driver ums-cypress
[   20.160000] usbcore: registered new interface driver ums-datafab
[   20.170000] usbcore: registered new interface driver ums-freecom
[   20.170000] usbcore: registered new interface driver ums-isd200
[   20.190000] usbcore: registered new interface driver ums-jumpshot
[   20.210000] usbcore: registered new interface driver ums-karma
[   20.230000] usbcore: registered new interface driver ums-sddr09
[   20.240000] usbcore: registered new interface driver ums-sddr55
[   20.240000] usbcore: registered new interface driver ums-usbat
[   20.380000] xt_time: kernel timezone is -0000
[   20.460000] cfg80211: Calling CRDA to update world regulatory domain
[   20.460000] cfg80211: World regulatory domain updated:
[   20.470000] cfg80211:  DFS Master region: unset
[   20.470000] cfg80211:   (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time)
[   20.480000] cfg80211:   (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
[   20.490000] cfg80211:   (2457000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
[   20.500000] cfg80211:   (2474000 KHz - 2494000 KHz @ 20000 KHz), (N/A, 2000 mBm), (N/A)
[   20.510000] cfg80211:   (5170000 KHz - 5250000 KHz @ 160000 KHz), (N/A, 2000 mBm), (N/A)
[   20.520000] cfg80211:   (5250000 KHz - 5330000 KHz @ 160000 KHz), (N/A, 2000 mBm), (0 s)
[   20.530000] cfg80211:   (5490000 KHz - 5730000 KHz @ 160000 KHz), (N/A, 2000 mBm), (0 s)
[   20.530000] cfg80211:   (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A)
[   20.540000] cfg80211:   (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 0 mBm), (N/A)
[   20.560000] l2tp_ppp: PPPoL2TP kernel driver, V2.0
[   20.740000] usbcore: registered new interface driver rtl8187
[   22.320000] usbcore: registered new interface driver rt2800usb
[   23.180000] cfg80211: Calling CRDA for country: US
[   23.200000] cfg80211: Regulatory domain changed to country: US
[   23.200000] cfg80211:  DFS Master region: FCC
[   23.210000] cfg80211:   (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time)
[   23.220000] cfg80211:   (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 3000 mBm), (N/A)
[   23.220000] cfg80211:   (5170000 KHz - 5250000 KHz @ 80000 KHz), (N/A, 2700 mBm), (N/A)
[   23.230000] cfg80211:   (5250000 KHz - 5330000 KHz @ 80000 KHz), (N/A, 2700 mBm), (0 s)
[   23.240000] cfg80211:   (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 3000 mBm), (N/A)
[   23.250000] cfg80211:   (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 4000 mBm), (N/A)
[   23.260000] ieee80211 phy0: Atheros AR9340 Rev:0 mem=0xb8100000, irq=47
[   48.010000] device eth1 entered promiscuous mode
[   52.420000] device wlan0 entered promiscuous mode
[   52.420000] br-lan: port 2(wlan0) entered forwarding state
[   52.430000] br-lan: port 2(wlan0) entered forwarding state
[   52.800000] eth0: link up (100Mbps/Full duplex)
[   52.800000] br-lan: port 2(wlan0) entered disabled state
[   55.930000] br-lan: port 2(wlan0) entered forwarding state
[   55.930000] br-lan: port 2(wlan0) entered forwarding state
[   57.930000] br-lan: port 2(wlan0) entered forwarding state
[   73.500000] eth0: link down
[   85.280000] jffs2_scan_eraseblock(): End of filesystem marker found at 0x0
[   85.310000] jffs2_build_filesystem(): unlocking the mtd device... done.
[   85.310000] jffs2_build_filesystem(): erasing all blocks after the end marker... done.
[   87.740000] jffs2: notice: (2699) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found.
[   89.790000] usb 1-1: USB disconnect, device number 2
[   90.110000] usb 1-1: new high-speed USB device number 3 using ehci-platform
[   90.270000] usb-storage 1-1:1.0: USB Mass Storage device detected
[   90.270000] scsi1 : usb-storage 1-1:1.0
[   91.290000] scsi 1:0:0:0: Direct-Access     Netac    OnlyDisk         PMAP PQ: 0 ANSI: 6
[   91.690000] sd 1:0:0:0: [sda] 31326208 512-byte logical blocks: (16.0 GB/14.9 GiB)
[   91.720000] sd 1:0:0:0: [sda] Write Protect is off
[   91.720000] sd 1:0:0:0: [sda] Mode Sense: 23 00 00 00
[   91.750000] sd 1:0:0:0: [sda] No Caching mode page found
[   91.750000] sd 1:0:0:0: [sda] Assuming drive cache: write through
[   91.780000] sd 1:0:0:0: [sda] No Caching mode page found
[   91.790000] sd 1:0:0:0: [sda] Assuming drive cache: write through
[   91.820000]  sda: sda1
[   91.830000] sd 1:0:0:0: [sda] No Caching mode page found
[   91.840000] sd 1:0:0:0: [sda] Assuming drive cache: write through
[   91.840000] sd 1:0:0:0: [sda] Attached SCSI removable disk
[   97.100000] FAT-fs (sda1): Volume was not properly unmounted. Some data may be corrupt. Please run fsck.
procd: - init complete -
[  134.140000] usb 1-1: USB disconnect, device number 3
[  134.440000] usb 1-1: new high-speed USB device number 4 using ehci-platform
[  134.600000] usb-storage 1-1:1.0: USB Mass Storage device detected
[  134.600000] scsi2 : usb-storage 1-1:1.0
[  135.150000] usb 1-1: USB disconnect, device number 4
[  135.450000] usb 1-1: new high-speed USB device number 5 using ehci-platform
[  135.600000] usb-storage 1-1:1.0: USB Mass Storage device detected
[  135.620000] scsi3 : usb-storage 1-1:1.0
[  136.620000] scsi 3:0:0:0: Direct-Access     Netac    OnlyDisk         PMAP PQ: 0 ANSI: 6
[  136.630000] sd 3:0:0:0: [sda] 31326208 512-byte logical blocks: (16.0 GB/14.9 GiB)
[  136.640000] sd 3:0:0:0: [sda] Write Protect is off
[  136.650000] sd 3:0:0:0: [sda] Mode Sense: 23 00 00 00
[  136.650000] sd 3:0:0:0: [sda] No Caching mode page found
[  136.660000] sd 3:0:0:0: [sda] Assuming drive cache: write through
[  136.670000] sd 3:0:0:0: [sda] No Caching mode page found
[  136.680000] sd 3:0:0:0: [sda] Assuming drive cache: write through
[  136.680000]  sda: sda1
[  136.700000] sd 3:0:0:0: [sda] No Caching mode page found
[  136.710000] sd 3:0:0:0: [sda] Assuming drive cache: write through
[  136.710000] sd 3:0:0:0: [sda] Attached SCSI removable disk
[  138.720000] FAT-fs (sda1): Volume was not properly unmounted. Some data may be corrupt. Please run fsck.
[  140.670000] usb 1-1: USB disconnect, device number 5
[  140.960000] usb 1-1: new high-speed USB device number 6 using ehci-platform
[  141.120000] usb-storage 1-1:1.0: USB Mass Storage device detected
[  141.120000] scsi4 : usb-storage 1-1:1.0
[  142.130000] scsi 4:0:0:0: Direct-Access     Netac    OnlyDisk         PMAP PQ: 0 ANSI: 6
[  142.140000] sd 4:0:0:0: [sda] 31326208 512-byte logical blocks: (16.0 GB/14.9 GiB)
[  142.150000] sd 4:0:0:0: [sda] Write Protect is off
[  142.160000] sd 4:0:0:0: [sda] Mode Sense: 23 00 00 00
[  142.160000] sd 4:0:0:0: [sda] No Caching mode page found
[  142.170000] sd 4:0:0:0: [sda] Assuming drive cache: write through
[  142.180000] sd 4:0:0:0: [sda] No Caching mode page found
[  142.190000] sd 4:0:0:0: [sda] Assuming drive cache: write through
[  142.190000]  sda: sda1
[  142.210000] sd 4:0:0:0: [sda] No Caching mode page found
[  142.220000] sd 4:0:0:0: [sda] Assuming drive cache: write through
[  142.220000] sd 4:0:0:0: [sda] Attached SCSI removable disk
[  143.330000] FAT-fs (sda1): Volume was not properly unmounted. Some data may be corrupt. Please run fsck.

点评

你发的这么多毫无意义 而且没人想看。 把wr800n的led对应的gpio测出来,包括点亮电平值 以便做对应的breed  详情 回复 发表于 2015-10-28 00:55
我的恩山、我的无线 The best wifi forum is right here.
发表于 2015-10-26 23:28 | 显示全部楼层
感谢H大的支持!!!
TL-WR800n v1的Reset键 led的gpio是GPIO#18
breed> btntst
Press Ctrl+C to stop.

GPIO#18 changed to 0
GPIO#18 changed to 1

期待中 ,谢谢!
我的恩山、我的无线 The best wifi forum is right here.
发表于 2015-10-27 10:08 | 显示全部楼层
大神威武,路由器原来可以这么玩
我的恩山、我的无线 The best wifi forum is right here.
发表于 2015-10-27 10:10 | 显示全部楼层
话说CPU超频有些什么好处呢?
我的恩山、我的无线 The best wifi forum is right here.
发表于 2015-10-27 21:09 | 显示全部楼层
楼主大大   斐讯PSG712 刷哪个breed?
我的恩山、我的无线 The best wifi forum is right here.
发表于 2015-10-27 22:20 | 显示全部楼层
hackpascal大大,我是极硬货HC5663,网上说基于极壹S(HC5661)增加SATA芯片而成。但是没有拆机,不能确认CPU和HC5661是否相同。请教一下,极硬货可以刷HC5661版本吗?breed-mt7620-hiwifi-hc5761.bin
因为这个是底层固件,刷错必砖,所以很谨慎。请大神告知一下。
感谢!

点评

请教一下,是不是CPU相同就可以?  详情 回复 发表于 2015-10-28 09:00
我怎么可能知道  发表于 2015-10-27 22:56
我的恩山、我的无线 The best wifi forum is right here.
您需要登录后才可以回帖 登录 | 立即注册

本版积分规则

QQ|手机版|小黑屋|Archiver|手机APP版|恩山无线论坛 ( 苏ICP备05084872号-1 )  

GMT+8, 2017-10-21 09:20

Powered by Discuz! X3.3

© 2001-2017 Comsenz Inc.

快速回复 返回顶部 返回列表