设为首页收藏本站

恩山无线论坛

 找回密码
 立即注册

QQ登录

只需一步,快速开始

搜索
楼主: hackpascal

【2017-06-13】AR/QCA/MTK Breed,功能强大的多线程 Bootloader

    [复制链接]
发表于 2017-1-31 01:50 | 显示全部楼层
我的恩山、我的无线 The best wifi forum is right here.
发表于 2017-1-31 10:00 | 显示全部楼层
是开发高手,顶帖致谢!
我的恩山、我的无线 The best wifi forum is right here.
发表于 2017-2-1 01:16 | 显示全部楼层
本帖最后由 vs2 于 2017-2-1 04:41 编辑

FW150R v2.0  AR7240 ,原版4M flash 32M DDR 没改过硬件。 从旧版Uboot 控制台升级到Breed 170116 失败
之前刷过tp 741ndv1 ,743ndv1 ,openwrt,石像鬼1.6-1.9.1 ,DDwrt V24 -V3.0 都正常成功 ,各固件均在web页面互刷成功。
--------------
试过几个解锁Uboot的OP固件或者bb cc内核的OPenwrt 下都提示mtd0 uboot分区写保护,不能打开用 mtd unlock 也无效
刷DDwrt 20161215 官网ftp的beta 版本,同样提示mtd0 写保护 RedBoot 不能改写

然后用DDWrt官网提供的恢复原厂固件先恢复到tp 741nd 再次刷 V24-sp版本的2013--03-25 ,mtd0 分区可以unlock 了,也可以写入uboot 了。

但直接写Breed到 mtd0,无出错提示的情况下, 无法启动控制台,按wps 加电 或者reset 加电 均无法进入控制台,用Breed中断工具也无效。Breed 试过两个版本,最新的170116 103KB,和一个16年的 99KB 两个都测试过无法成功进入Breed控制台,这两个版本也试过Hex补全128KB 依旧不成功。

目前试过可以成功是旧版的Uboot 信息如下
CPU        Atheros AR7240 rev 2
内存        32MB DDR
闪存        Spansion S25FL032P @ 25MHz (4MB)
以太网        Atheros AR8216 (built-in) rev 2
系统频率        CPU: 400MHz, DDR: 400MHz, AHB: 200MHz, Ref: 5MHz
编译日期        2015-04-27 09:17:20 +08:00
-----------------------------------------------------------------------------------

启动失败的Breed 校验信息 :
breed-ar724x.bin
大小: 106011 字节
MD5: CBE94109A75A98753779C73F3A3BC958
SHA1: 5476E96D47C4C439A2953280B2F76AEB47032453
CRC32: B9EF6C82另一个早期的Breed也是不能启动
breed-ar724x.bin
大小: 101563 字节
MD5: 38B3ADBD956A007B2913B684FFC2F9A5
SHA1: 7EB95DEE0367505533F555ED10AF0F449D40080B
CRC32: 47F1381A

---------------------------- 可以成功启动控制台的Uboot---
u-boot-ar7240_ar7241.bin
大小: 131072 字节
MD5: 1FED33DFB496F0D6E2A7BB03137FCDD9
SHA1: 78D60B093B274FA836F7F65682287B6B73D47A08
CRC32: A5C3FE5F


在有效的U-boot控制台里,固件更新-常规固件-U-boot 栏目试过更新以上两个Breed 也是失败。更新后无法用BreedEnter/按Reset /wps 按键进入到控制台。
按住reset 上电后,所有灯 在快闪3次后熄灭,SYS灯进入间歇1s 左右的2Hz 闪烁,此时ping 192.168.1.1不通 web不响应。,如果全部灯快闪3次期间或者紧接着释放reset ,能引导到DDwrt 。

以上用win7x86 ,IE8.0 和UC浏览器 测试,结果一致。



点评

没给出任何一个有用的信息。另外我不打算再更新ar老型号的了  发表于 2017-2-1 22:00
我的恩山、我的无线 The best wifi forum is right here.
发表于 2017-2-2 05:05 | 显示全部楼层

Boot and Recovery Environment for Embedded Devices
Copyright (C) 2017 HackPascal <[email protected]>
Build date 2017-01-16 [git-7e65927]
Version 1.1 (r1008)

DRAM: 32MB
Platform: Atheros AR7240 rev 2
Board: Generic board
Clocks: CPU: 400MHz, DDR: 400MHz, AHB: 200MHz, Ref: 40MHz
Flash: Spansion S25FL032P (4MB) on ath79-spi
ag71xx-eth: MAC address is invalid, using default settings.
ag71xx-eth: Using MAC address 00:13:74:00:00:01
Waiting for auto-negotiation complete ... OK
eth0: Generic PHY driver
ag71xx-eth: MAC address is invalid, using default settings.
ag71xx-eth: Using MAC address 00:13:74:00:00:01
Waiting for auto-negotiation complete ... OK
eth1: Atheros AR8216 rev 2

Network started on eth0, inet addr 192.168.1.1, netmask 255.255.255.0
Network started on eth1, inet addr 192.168.1.1, netmask 255.255.255.0

Press any key to interrupt autoboot ... 2
Autoboot aborted due to button press.

Starting breed built-in shell

breed>

++++ 以上为刷入了r1008版本 Breed-7240x.bin 启动TTL信息,到以上位置停止不动了

-------------------------以下为Breed-7240x.bin的常规启动信息,启动到DDwrt------------------------------------------------


Boot and Recovery Environment for Embedded Devices
Copyright (C) 2017 HackPascal <[email protected]>
Build date 2017-01-16 [git-7e65927]
Version 1.1 (r1008)

DRAM: 32MB
Platform: Atheros AR7240 rev 2
Board: Generic board
Clocks: CPU: 400MHz, DDR: 400MHz, AHB: 200MHz, Ref: 40MHz
Flash: Spansion S25FL032P (4MB) on ath79-spi
ag71xx-eth: MAC address is invalid, using default settings.
ag71xx-eth: Using MAC address 00:13:74:00:00:01
Waiting for auto-negotiation complete ... OK
eth0: Generic PHY driver
ag71xx-eth: MAC address is invalid, using default settings.
ag71xx-eth: Using MAC address 00:13:74:00:00:01
Waiting for auto-negotiation complete ... OK
eth1: Atheros AR8216 rev 2

Network started on eth0, inet addr 192.168.1.1, netmask 255.255.255.0
Network started on eth1, inet addr 192.168.1.1, netmask 255.255.255.0

Press any key to interrupt autoboot ... 0

Trying to boot firmware from 0x9f020000 ...
TP-LINK firmware image header detected.
    Image Name:   07410001
    Data Size:    924246 Bytes
    Load Address: 80002000
    Entry Point:  80002000
Uncompressing data (GZIP) ... done.
Flushing cache ... done.

Starting kernel at 0x80002000...

OpenWrt kernel loader for AR7XXX/AR9XXX
Copyright (C) 2011 Gabor Juhos <[email protected]>
Decompressing kernel...
done!
Starting kernel...

[    0.000000] flash_size passed from bootloader = 1731
[    0.000000] bootconsole [early0] enabled
AR7240
detect mem size
Uart Init
Booting AR7240(Python)...
[    0.000000] Determined physical RAM map:
[    0.000000]  memory: 02000000 @ 00000000 (usable)
[    0.000000] Zone ranges:
[    0.000000]   Normal   [mem 0x00000000-0x01ffffff]
[    0.000000] Movable zone start for each node
[    0.000000] Early memory node ranges
[    0.000000]   node   0: [mem 0x00000000-0x01ffffff]
[    0.000000] Primary instruction cache 64kB, 4-way, VIPT, I-cache aliases, linesize 32 bytes.
[    0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
[    0.000000] Linux version 3.5.7 ([email protected]) (gcc version 4.7.3 20121205 (prerelease) (Linaro GCC 4.7-2012.12) ) #6148 Mon Mar 25 08:58:25 CET 2013
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 8128
[    0.000000] Kernel command line: console=ttyS0,115200 root=1f02 rootfstype=squashfs noinitrd init=/sbin/init
[    0.000000] PID hash table entries: 128 (order: -3, 512 bytes)
[    0.000000] Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)
[    0.000000] Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)
[    0.000000] __ex_table already sorted, skipping sort
[    0.000000] Writing ErrCtl register=0007f7f0
[    0.000000] Readback ErrCtl register=0007f7f0
[    0.000000] Memory: 29472k/32768k available (2120k kernel code, 3296k reserved, 411k data, 164k init, 0k highmem)
[    0.000000] NR_IRQS:80
[    0.000000] Calibrating delay loop... 265.42 BogoMIPS (lpj=1327104)
[    0.080000] pid_max: default: 32768 minimum: 301
[    0.080000] Mount-cache hash table entries: 512
[    0.090000] NET: Registered protocol family 16
[    0.130000] found calibration data for slot 0 on 0xBF3F1000
[    0.340000] registering PCI controller with io_map_base unset
[    0.360000] bio: create slab <bio-0> at 0
[    0.360000] PCI host bridge to bus 0000:00
[    0.370000] pci_bus 0000:00: root bus resource [mem 0x10000000-0x13ffffff]
[    0.370000] pci_bus 0000:00: root bus resource [io  0x0000]
[    0.380000] pci 0000:00:00.0: fixup device configuration
[    0.380000] bootstrap returns device 168C:2B
[    0.390000] pci 0000:00:00.0: BAR 0: assigned [mem 0x10000000-0x1000ffff 64bit]
[    0.390000] PCI: mapping irq 72 to [email protected]:00:00.0
[    0.400000] Switching to clocksource MIPS
[    0.400000] NET: Registered protocol family 2
[    0.410000] IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.410000] TCP established hash table entries: 1024 (order: 1, 8192 bytes)
[    0.420000] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
[    0.420000] TCP: Hash tables configured (established 1024 bind 1024)
[    0.430000] TCP: reno registered
[    0.430000] UDP hash table entries: 256 (order: 0, 4096 bytes)
[    0.440000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[    0.450000] NET: Registered protocol family 1
[    0.450000] gpio_proc: module loaded and /proc/gpio/ created
[    0.460000] fixup WR741 Switch LED's
[    0.460000] wl0gpio_proc: module loaded and /proc/wl0gpio/ created
[    0.470000] squashfs: version 3.0 (2006/03/15) Phillip Lougher
[    0.470000] msgmni has been set to 57
[    0.480000] io scheduler noop registered (default)
[    0.480000] Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled
[    0.510000] serial8250.0: ttyS0 at MMIO 0x18020000 (irq = 11) is a 16550A
[    0.520000] console [ttyS0] enabled, bootconsole disabled
[    0.520000] console [ttyS0] enabled, bootconsole disabled
[    0.530000] guessed flashsize = 4M
[    0.530000] scanning for root partition
[    0.540000] tplink uboot detected
[    0.540000] guessed bootloader size = 20000
[    0.550000]
[    0.550000] found squashfs at 110000
[    0.550000] Creating 8 MTD partitions on "ar7240-nor0":
[    0.560000] 0x000000000000-0x000000020000 : "RedBoot"
[    0.570000] 0x000000020000-0x0000003e0000 : "linux"
[    0.570000] 0x000000110000-0x0000003e0000 : "rootfs"
[    0.580000] mtd: partition "rootfs" set to be root filesystem
[    0.580000] 0x0000003e0000-0x000000400000 : "ddwrt"
[    0.590000] 0x0000003e0000-0x0000003f0000 : "nvram"
[    0.600000] 0x0000003f0000-0x000000400000 : "board_config"
[    0.600000] 0x000000000000-0x000000400000 : "fullflash"
[    0.610000] 0x000000000000-0x000000020000 : "fullboot"
[    1.020000] PPP generic driver version 2.4.2
[    1.020000] PPP BSD Compression module registered
[    1.030000] PPP Deflate Compression module registered
[    1.030000] PPP MPPE Compression module registered
[    1.040000] NET: Registered protocol family 24
[    1.060000] u32 classifier
[    1.060000]     Performance counters on
[    1.070000]     input device check on
[    1.070000]     Actions configured
[    1.070000] Netfilter messages via NETLINK v0.30.
[    1.080000] nf_conntrack version 0.5.0 (460 buckets, 1840 max)
[    1.080000] nf_conntrack_rtsp v0.6.21 loading
[    1.090000] nf_nat_rtsp v0.6.21 loading
[    1.090000] ip_tables: (C) 2000-2006 Netfilter Core Team
[    1.100000] IPP2P v0.8.2 loading
[    1.100000] TCP: westwood registered
[    1.110000] TCP: hybla registered
[    1.110000] TCP: vegas registered
[    1.110000] NET: Registered protocol family 17
[    1.120000] Bridge firewalling registered
[    1.120000] 8021q: 802.1Q VLAN Support v1.8
[    1.130000] searching for nvram
[    1.130000] nvram size = 0
[    1.160000] Atheros AR71xx hardware watchdog driver version 0.1.0
[    1.170000] ar71xx-wdt: timeout=15 secs (max=21) ref freq=200000000
[    1.180000] VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
[    1.190000] Freeing unused kernel memory: 164k freed
start service
starting Architecture code for wr741
starting hotplug
Jan  1 00:00:02 udevtrigger[238]: parse_config_file: can't open '/etc/udev/udev.conf' as config file: No such file or directory
done
load ATH Ethernet Driver
[    4.050000] ag71xx_mdio: probed
[    4.050000] eth0: Atheros AG71xx at 0xb9000000, irq 4, mode:MII
[    4.630000] ag71xx ag71xx.0: eth0: connected to PHY at ag71xx-mdio.0:04 [uid=004dd041, driver=Generic PHY]
[    4.640000] eth1: Atheros AG71xx at 0xba000000, irq 5, mode:GMII
[    5.220000] eth1: Found an AR7240/AR9330 built-in switch
configure eth0 to ff:ff:ff:ff:ff:ff
configure eth1 to FF:FF:FF:00:00:02
/bin/sh: can't create /sys/class/leds/generic_13/port_mask: nonexistent directory
/bin/sh: can't create /sys/class/leds/generic_14/port_mask: nonexistent directory
/bin/sh: can't create /sys/class/leds/generic_15/port_mask: nonexistent directory
/bin/sh: can't create /sys/class/leds/generic_16/port_mask: nonexistent directory
load ATH 802.11 a/b/g Driver
load ATH9K 802.11n Driver
[    8.610000] Compat-drivers backport release: compat-drivers-2013-01-21-1
[    8.610000] Backport based on wireless-testing.git master-2013-02-22
[    8.620000] compat.git: wireless-testing.git
[    8.810000] cfg80211: Calling CRDA to update world regulatory domain
[    8.810000] cfg80211: World regulatory domain updated:
[    8.820000] cfg80211:   (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[    8.820000] cfg80211:   (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[    8.830000] cfg80211:   (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[    8.840000] cfg80211:   (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[    8.850000] cfg80211:   (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[    8.860000] cfg80211:   (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[    9.520000] eth1: link up (1000Mbps/Full duplex)
[    9.570000] ieee80211 phy0: Atheros AR9285 Rev:2 mem=0xb0000000, irq=72
[    9.570000] cfg80211: Calling CRDA for country: US
[    9.580000] cfg80211: Regulatory domain changed to country: US
[    9.580000] cfg80211:   (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[    9.590000] cfg80211:   (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2700 mBm)
[    9.600000] cfg80211:   (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 1700 mBm)
[    9.610000] cfg80211:   (5250000 KHz - 5330000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[    9.610000] cfg80211:   (5490000 KHz - 5600000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[    9.620000] cfg80211:   (5650000 KHz - 5710000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[    9.630000] cfg80211:   (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 3000 mBm)
[    9.640000] cfg80211:   (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 4000 mBm)
ath9k deconfigure_single: phy0 ath0
[   11.460000] device eth0 entered promiscuous mode
[   11.470000] eth1: link down
[   13.570000] device eth1 entered promiscuous mode
ath9k deconfigure_single: phy0 ath0
[   13.640000] cfg80211: Calling CRDA to update world regulatory domain
[   13.650000] cfg80211: World regulatory domain updated:
[   13.650000] cfg80211:   (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[   13.660000] cfg80211:   (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[   13.670000] cfg80211:   (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[   13.680000] cfg80211:   (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[   13.680000] cfg80211:   (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[   13.690000] cfg80211:   (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[   13.730000] cfg80211: Calling CRDA for country: US
[   13.740000] cfg80211: Regulatory domain changed to country: US
[   13.740000] cfg80211:   (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[   13.750000] cfg80211:   (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2700 mBm)
[   13.760000] cfg80211:   (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 1700 mBm)
[   13.770000] cfg80211:   (5250000 KHz - 5330000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[   13.770000] cfg80211:   (5490000 KHz - 5600000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[   13.780000] cfg80211:   (5650000 KHz - 5710000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[   13.790000] cfg80211:   (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 3000 mBm)
[   13.800000] cfg80211:   (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 4000 mBm)
ath9k configure_single: phy0 ath0
549:ath0
call mac80211autochannel for interface: ath0
Scan request failed: Network is down
Scan request failed: Network is down
freq:2412 qual:0 noise:0
freq:2417 qual:0 noise:0
freq:2422 qual:0 noise:0
freq:2427 qual:0 noise:0
freq:2432 qual:0 noise:0
freq:2437 qual:0 noise:0
freq:2442 qual:0 noise:0
freq:2447 qual:0 noise:0
freq:2452 qual:0 noise:0
freq:2457 qual:0 noise:0
freq:2462 qual:0 noise:0
mac80211autochannel interface: ath0 frequency: 2412
setup ath0 FF:FF:FF:FF:FF:FF
can't add ath0 to bridge br0: Invalid argument
[   14.740000] eth1: link up (1000Mbps/Full duplex)
[   14.740000] br0: port 2(eth1) entered forwarding state
[   14.750000] br0: port 2(eth1) entered forwarding state
br0: No such process
SIOCGIFFLAGS: No such device
SIOCGIFFLAGS: No such device
[   16.750000] br0: port 2(eth1) entered forwarding state
connect: Network is unreachable
connect: Network is unreachable
connect: Network is unreachable
gethostbyname: Network is unreachable
SIOCGIFFLAGS: No such device
[   21.200000] nf_conntrack: automatic helper assignment is deprecated and it will be removed soon. Use the iptables CT target to attach helpers instead.
ath9k radio 1: phy0 ath0
[   23.230000] etherip: Ethernet over IPv4 tunneling driver
connect: Network is unreachable
connect: Network is unreachable
connect: Network is unreachable
gethostbyname: Network is unreachable
[APPLY] index (null) (null)
submit_button=[index] submit_type=[changepass]
name=[index] type=[changepass] service=[] sleep=[1] action=[5]
connect: Network is unreachable
connect: Network is unreachable
connect: Network is unreachable
gethostbyname: Network is unreachable
[APPLY] index (null) (null)
submit_button=[index] submit_type=[changepass]
name=[index] type=[changepass] service=[] sleep=[1] action=[5]
-----------------------------END-----------------------

------------------以下为Uboot控制台成功启动的TTL信息---------------------
U-Boot 1.1.4 (Apr 27 2015 - 09:18:17)

AP91 (AR7240 - Python 1.2) U-Boot
DRAM:  32 MB
Flash: Spansion S25FL032P (4 MB)
Using default environment

Clocks: CPU:400MHz, DDR:400MHz, AHB:200MHz, Ref:5MHz
In:    serial
Out:   serial
Err:   serial
Net:   ag7240_enet_initialize...
Fetching MAC Address from 0x9f01fc00
Fetching MAC Address from 0x9f01fc00
GMAC: cfg1 0xf cfg2 0x7114
eth0: 00:23:45:67:89:ab
eth0 up
GMAC: cfg1 0xf cfg2 0x7214
eth1: 00:23:45:67:89:ac
ATHRS26: resetting s26
ATHRS26: s26 reset done
eth1 up
eth0, eth1

Push the reset/WPS button for 3s to start Web Failsafe.

Hit any key to stop autoboot:  0
eth0 link down
dup 1 speed 1000
Web console started at 192.168.1.1
GET / HTTP/1.1
GET /style.css HTTP/1.1

点评

另外说一下 你能使路由的一个led进行一定规律的闪烁就说明breed已经中止了启动 至于不能访问breed页面是因为ar7240有硬件bug,网络模块造成的,这个是没法修复的  详情 回复 发表于 2017-2-2 15:49
我只看得出来第一个明显复位键不对。给内核输出没用。uboot的我不看。  发表于 2017-2-2 14:37
我的恩山、我的无线 The best wifi forum is right here.
发表于 2017-2-2 12:17 | 显示全部楼层
感谢楼主的辛勤劳动,膜拜大神
我的恩山、我的无线 The best wifi forum is right here.
 楼主| 发表于 2017-2-2 15:49 | 显示全部楼层
vs2 发表于 2017-2-2 05:05
Boot and Recovery Environment for Embedded Devices
Copyright (C) 2017 HackPascal
Build date 201 ...

另外说一下
你能使路由的一个led进行一定规律的闪烁就说明breed已经中止了启动
至于不能访问breed页面是因为ar7240有硬件bug,网络模块造成的,这个是没法修复的

点评

H大,能否出一个网络接口为eth1的breed-ar7161-blank.bin。  详情 回复 发表于 2017-2-5 14:01
vs2
测试过 GPIO11 是RESET GPIO12 是WPS按键 ,刷了网盘上提供的R1008 目录下的Breed-ar724x11.bin 也是一样的,按住Reset 或者wps 按钮上电都是和第一个一样,启动到Breed 就停了. 要是Breed 在ar7240上有bug不能用,  详情 回复 发表于 2017-2-2 16:12
我的恩山、我的无线 The best wifi forum is right here.
发表于 2017-2-2 16:12 | 显示全部楼层
hackpascal 发表于 2017-2-2 15:49
另外说一下
你能使路由的一个led进行一定规律的闪烁就说明breed已经中止了启动
至于不能访问breed页面 ...

测试过 GPIO11 是RESET  GPIO12 是WPS按键  ,刷了网盘上提供的R1008 目录下的Breed-ar724x11.bin 也是一样的,按住Reset 或者wps 按钮上电都是和第一个一样,启动到Breed 就停了.

要是Breed 在ar7240上有bug不能用,网盘上又提供下载的是Breed, Uboot 历史版本也没提供下载了,没办法回滚到有效的上个版本,原本的Uboot控制台没备份的话,这如何是好.
如果有Breed 的历史版本有提供下载 还可以试试到底哪个版本的可以用了.  
我的恩山、我的无线 The best wifi forum is right here.
发表于 2017-2-2 19:52 | 显示全部楼层
hackpascal 发表于 2015-3-21 22:38
更新日志

[2017-01-16 r1008]

牛逼的大神 ,老不死U-BOOT更新是选更新U-BOOT,还是选更新固件,谢谢
我的恩山、我的无线 The best wifi forum is right here.
发表于 2017-2-2 20:15 | 显示全部楼层
H大能不能增加智博通3526的breed支持呢。我愿意提供机子给研究
我的恩山、我的无线 The best wifi forum is right here.
发表于 2017-2-4 19:07 | 显示全部楼层
楼主 请问支持极路由4增强版吗
我的恩山、我的无线 The best wifi forum is right here.
发表于 2017-2-5 11:14 | 显示全部楼层
萌新入门来看看大佬
我的恩山、我的无线 The best wifi forum is right here.
发表于 2017-2-5 14:01 | 显示全部楼层
本帖最后由 huangchao222 于 2017-2-5 15:30 编辑
hackpascal 发表于 2017-2-2 15:49
另外说一下
你能使路由的一个led进行一定规律的闪烁就说明breed已经中止了启动
至于不能访问breed页面 ...

H大,什么时候有空能否出一个网络接口为eth1的breed-ar7161-blank.bin,或者能通过env配置就更好了。
我的恩山、我的无线 The best wifi forum is right here.
发表于 2017-2-5 18:32 | 显示全部楼层
下载了,等下用。
我的恩山、我的无线 The best wifi forum is right here.
发表于 2017-2-5 19:32 | 显示全部楼层
Breed可以用在只有一个WAN口的极路由GO上吗? 配置是MT7628,和极1S应该是一样的
我的恩山、我的无线 The best wifi forum is right here.
发表于 2017-2-6 08:30 | 显示全部楼层
非常好的资源。
我的恩山、我的无线 The best wifi forum is right here.
您需要登录后才可以回帖 登录 | 立即注册

本版积分规则

QQ|手机版|小黑屋|Archiver|手机APP版|恩山无线论坛 ( 苏ICP备05084872号-1  

GMT+8, 2017-7-22 18:58

Powered by Discuz! X3.3

© 2001-2017 Comsenz Inc.

快速回复 返回顶部 返回列表