OpenWRT For WR740n v5(FW150r v5)(接近完美)/WR703N(官方支持) (20110922更新)

小标

同问，楼主是如何编译ar9331 openwrt固件的？

小标

楼主可否说下703n该刷那个版本的openwrt？自己编译的也行，貌似openwrt还不支持ar9331，请问楼主是如何编译出来的？

小标

13# 729650915


向高手致敬

小标

等openwrt官方源码对ar9331的支持

小标

官方支持703n了？太好了，马上svn up更新源码编译一个玩玩。

小标

请教楼主，囧，更新trunk源码后，make menuconfig后选择路由型号时没有出现703n选项。

小标

52# kohain


703n本身的固件就是支持中继，没必要刷dd

小标

51# 729650915


谢谢，终于有703n选项了

小标

1# 729650915


楼主你好，有个问题请教一下，今晚我编译了集成3g拨号的703n固件，把华为et127插上703n测试了一下，能成功拨上3g，但发现一个问题就是路由上的设置在路由重启后就会完全丢失，跟恢复原厂设置一样，还有就是“系统-软件包”的内存显示有问题，居然显示还剩14M空间，请问如何解决上述问题？谢谢

小标

rg100a的3g固件搞完又来搞703n了啊
tp官方的废柴固件换你的得了
zz243 发表于 2011-9-23 10:57

rg100a的体积太大了，做3g路由不方便携带，703n最合适，目前已经在703n上可以用openwrt拨号3g了

小标

57# 729650915
mount和dmesg信息发上来了，麻烦楼主看看，如何解决路由重启后所有设置丢失的问题?曾经编译741nd的trunk版固件时也出现这样的问题，后来换了backfire版源码再编译就正常了。


root@OpenWrt:~# mount
rootfs on / type rootfs (rw)
/dev/root on /rom type squashfs (ro,relatime)
proc on /proc type proc (rw,noatime)
sysfs on /sys type sysfs (rw,noatime)
tmpfs on /tmp type tmpfs (rw,nosuid,nodev,noatime,size=14780k)
tmpfs on /dev type tmpfs (rw,noatime,size=512k,mode=755)
devpts on /dev/pts type devpts (rw,noatime,mode=600)
root on /tmp/root type tmpfs (rw,noatime,mode=755)
overlayfs:/tmp/root on / type overlayfs (rw,noatime)
debugfs on /sys/kernel/debug type debugfs (rw,relatime)
none on /proc/bus/usb type usbfs (rw,relatime)


root@OpenWrt:~# dmesg
Linux version 2.6.39.4 (palmerxiaobiao@palmerxiaobiao-virtual-machine) (gcc version 4.5.4 20110808 (prerelease) (Linaro GCC

4.5-2011.08) ) #1 Thu Sep 22 19:53:25 CST 2011
prom: fw_arg0=00000007, fw_arg1=a1f8ffb0, fw_arg2=a1f90460, fw_arg3=00000004
MyLoader: sysp=00d73bc7, boardp=ed0c292e, parts=97cba183
bootconsole [early0] enabled
CPU revision is: 00019374 (MIPS 24Kc)
SoC: Atheros AR9330 rev 1
Clocks: CPU:400.000MHz, DDR:400.000MHz, AHB:200.000MHz, Ref:25.000MHz
Determined physical RAM map:
memory: 02000000 @ 00000000 (usable)
Initrd not found or empty - disabling initrd
Zone PFN ranges:
  Normal   0x00000000 -> 0x00002000
Movable zone start PFN for each node
early_node_map[1] active PFN ranges
    0: 0x00000000 -> 0x00002000
On node 0 totalpages: 8192
free_area_init_node: node 0, pgdat 802b6570, node_mem_map 81000000
  Normal zone: 64 pages used for memmap
  Normal zone: 0 pages reserved
  Normal zone: 8128 pages, LIFO batch:0
pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
pcpu-alloc: [0] 0
Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 8128
Kernel command line:  board=TL-WR703N console=ttyATH0,115200 rootfstype=squashfs,jffs2 noinitrd
PID hash table entries: 128 (order: -3, 512 bytes)
Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)
Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)
Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
Writing ErrCtl register=00000000
Readback ErrCtl register=00000000
Memory: 29380k/32768k available (2009k kernel code, 3388k reserved, 385k data, 176k init, 0k highmem)
SLUB: Genslabs=9, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
NR_IRQS:80
Calibrating delay loop... 265.42 BogoMIPS (lpj=1327104)
pid_max: default: 32768 minimum: 301
Mount-cache hash table entries: 512
NET: Registered protocol family 16
MIPS: machine is TP-LINK TL-WR703N v1
bio: create slab <bio-0> at 0
Switching to clocksource MIPS
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 1024 (order: 1, 8192 bytes)
TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
TCP: Hash tables configured (established 1024 bind 1024)
TCP reno registered
UDP hash table entries: 256 (order: 0, 4096 bytes)
UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
NET: Registered protocol family 1
PCI: CLS 0 bytes, default 32
squashfs: version 4.0 (2009/01/31) Phillip Lougher
JFFS2 version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
msgmni has been set to 57
io scheduler noop registered
io scheduler deadline registered (default)
Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled
ar933x-uart: ttyATH0 at MMIO 0x18020000 (irq = 11) is a AR933X UART
console [ttyATH0] enabled, bootconsole disabled
Atheros AR71xx SPI Controller driver version 0.2.4
m25p80 spi0.0: found s25sl032a, expected m25p80
m25p80 spi0.0: s25sl032a (4096 Kbytes)
spi0.0: searching for MyLoader partition table at offset 0x10000
spi0.0: searching for MyLoader partition table at offset 0x20000
spi0.0: searching for MyLoader partition table at offset 0x30000
spi0.0: searching for MyLoader partition table at offset 0x40000
spi0.0: no MyLoader partition table found
Searching for RedBoot partition table in spi0.0 at offset 0x3e0000
Searching for RedBoot partition table in spi0.0 at offset 0x3f0000
No RedBoot partition table detected in spi0.0
spi0.0: no WRT160NL signature found
Creating 5 MTD partitions on "spi0.0":
0x000000000000-0x000000020000 : "u-boot"
0x000000020000-0x000000120000 : "kernel"
0x000000120000-0x0000003f0000 : "rootfs"
mtd: partition "rootfs" set to be root filesystem
mtd: partition "rootfs_data" created automatically, ofs=3B0000, len=40000
0x0000003b0000-0x0000003f0000 : "rootfs_data"
0x0000003f0000-0x000000400000 : "art"
0x000000020000-0x0000003f0000 : "firmware"
ag71xx_mdio: probed
eth0: Atheros AG71xx at 0xb9000000, irq 4
eth0: connected to PHY at ag71xx-mdio:04 [uid=004dd041, driver=Generic PHY]
Atheros AR71xx hardware watchdog driver version 0.1.0
ar71xx-wdt: timeout=15 secs (max=171)
TCP westwood registered
NET: Registered protocol family 17
802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
All bugs added by David S. Miller <davem@redhat.com>
VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
Freeing unused kernel memory: 176k freed
input: gpio-keys-polled as /devices/platform/gpio-keys-polled/input/input0
Button Hotplug driver version 0.4.1
Registered led device: tl-wr703n:blue:system
device eth0 entered promiscuous mode
Compat-wireless backport release: compat-wireless-2011-08-25
Backport based on wireless-testing.git master-2011-09-14
cfg80211: Calling CRDA to update world regulatory domain
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
cfg80211: World regulatory domain updated:
cfg80211:     (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
cfg80211:     (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
cfg80211:     (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
cfg80211:     (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
cfg80211:     (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
cfg80211:     (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
ath: EEPROM regdomain: 0x0
ath: EEPROM indicates default country code should be used
ath: doing EEPROM country->regdmn map search
ath: country maps to regdmn code: 0x3a
ath: Country alpha2 being used: US
ath: Regpair used: 0x3a
ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
Registered led device: ath9k-phy0
ieee80211 phy0: Atheros AR9330 Rev:1 mem=0xb8100000, irq=2
cfg80211: Calling CRDA for country: US
PPP generic driver version 2.4.2
tun: Universal TUN/TAP device driver, 1.6
tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
cfg80211: Regulatory domain changed to country: US
cfg80211:     (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
cfg80211:     (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2700 mBm)
cfg80211:     (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 1700 mBm)
cfg80211:     (5250000 KHz - 5330000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
cfg80211:     (5490000 KHz - 5600000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
cfg80211:     (5650000 KHz - 5710000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
cfg80211:     (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 3000 mBm)
ip_tables: (C) 2000-2006 Netfilter Core Team
NET: Registered protocol family 24
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
ar71xx-ehci ar71xx-ehci: Atheros AR91xx built-in EHCI controller
ar71xx-ehci ar71xx-ehci: new USB bus registered, assigned bus number 1
ar71xx-ehci ar71xx-ehci: irq 3, io mem 0x1b000000
ar71xx-ehci ar71xx-ehci: USB 2.0 started, EHCI 1.00
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
nf_conntrack version 0.5.0 (461 buckets, 1844 max)
ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
usbcore: registered new interface driver cdc_acm
cdc_acm: v0.26:USB Abstract Control Model driver for USB modems and ISDN adapters
usbcore: registered new interface driver usbserial
USB Serial support registered for generic
usbcore: registered new interface driver usbserial_generic
usbserial: USB Serial Driver core
USB Serial support registered for GSM modem (1-port)
usbcore: registered new interface driver option
option: v0.7.2:USB Driver for GSM modems
eth0: link up (100Mbps/Full duplex)
br-lan: port 1(eth0) entering forwarding state
br-lan: port 1(eth0) entering forwarding state
jffs2: Too few erase blocks (4)
ar71xx-wdt: enabling watchdog timer
ar71xx-wdt: timeout=60 secs
eth0: link down
br-lan: port 1(eth0) entering forwarding state
eth0: link up (100Mbps/Full duplex)
br-lan: port 1(eth0) entering forwarding state
br-lan: port 1(eth0) entering forwarding state
eth0: link down
br-lan: port 1(eth0) entering forwarding state
eth0: link up (100Mbps/Full duplex)
br-lan: port 1(eth0) entering forwarding state
br-lan: port 1(eth0) entering forwarding state
root@OpenWrt:~#

小标

这个不要集成的，block-extroot是实现把软件安装到U盘上才需要的，在编译741nd固件时也出现设置在路由重启后丢失的问题，换了backfire源码就解决了。

小标

79# cncaihua
哪有什么60kb，我的703n就是刷openwrt，下载160kb/s以上