更新HG320等64M机升级NR236W新版以及1.7 0306版与tomato互刷免TTL全智能刷机脚本

fashi***

HG320现在用独舞的cfe和固件，是不是可以独舞的cfe刷235后，无线修改端口，然后运行相应脚本自动升级呢

ath***

txm***

今天刷了 3月7号得的 无线信号和以前1.4版的一样比较弱

txm***

没有翅膀的鱼 发表于 2013-3-7 11:59
请问盗版的会砖头不

GR200E-CA 刷了没变砖 正常重启了几次都正常

樊***

悲剧 我的rg200e从TT直接刷NR235w 1.7 B5版，然后用你的脚本new236.vbs刷到1.7正式版后 开机有线无线都ping不通, 只有接有线相应端口的 灯会闪动其余灯都是灭的，这是不是砖了

过期***

樊诚 发表于 2013-3-8 01:28
悲剧 我的rg200e从TT直接刷NR235w 1.7 B5版，然后用你的脚本new236.vbs刷到1.7正式版后 开机有线无线都ping ...

楼上的没有看仔细。从tt刷磊科，要先刷1.6以下的版本，再运行脚本科

wyy***

可以从1.7开始的

樊***

过期的可乐 发表于 2013-3-8 06:45
楼上的没有看仔细。从tt刷磊科，要先刷1.6以下的版本，再运行脚本科

我以为1.6 和1.7B5之间的固件都是不用管cfe 直接升级的 ，我就升了，现在不知道是半砖还是全砖

用ttl能否修复呀

fyzy***

点击脚本升级 提示TFTP timeout，这是什么原因 我是1.5多拨版本的 ，好像升不了。

fyzy***

/ $ cd tmp
/var/tmp $ tftp -g -r cfe.old 192.168.162.1 cfe.old
tftp -g -r tomato.trx 192.168.162.1 tomato.trx
tftp: timeout
tftp: timeout
mtd_write boot cfe.old 0 131072
tftp: timeout
mtd_write linux tomato.trx 0 7020544
tftp: timeout
tftp: timeout
tftp: last timeout
/var/tmp $ tftp -g -r tomato.trx 192.168.162.1 tomato.trx
tftp: timeout
tftp: timeout
tftp: timeout
tftp: timeout
tftp: timeout
tftp: last timeout
/var/tmp $ mtd_write boot cfe.old 0 131072
upgrade boot , file cfe.old
Truncated file (actual 0 expect 131072)
/var/tmp $ mtd_write linux tomato.trx 0 7020544
File read error
/var/tmp $
完全按照脚本自动执行的，结果输出这样的内容，请问是什么原因 固件是1.5多拨版本

my***

悲剧 我的rg200e从NR236w 1.6版，然后用你的脚本new236.vbs刷到1.7正式版后 开机有线无线都ping不通, 只有接有线相应端口的 灯会闪动其余灯都是灭的，这是不是砖了


ttl 能进

Decompressing...done

CFE version 5.100.138.22 based on BBP 1.0.37 for BCM947XX (32bit,SP,LE)
Build Date: Thu Jan 24 14:18:09 CST 2013 (root@robert-virtual-machine)
Copyright (C) 2000-2008 Broadcom Corporation.
Init Arena
Init Devs.
Boot partition size = 131072(0x20000)
Found an ST compatible serial flash with 256 64KB blocks; total size 16MB
et0: Broadcom BCM47XX 10/100/1000 Mbps Ethernet Controller 5.100.138.22
CPU type 0x19749: 500MHz
Tot mem: 65536 KBytes
CFE mem:    0x80700000 - 0x80799A00 (629248)
Data:       0x8072F7B0 - 0x80732A90 (13024)
BSS:        0x80732A90 - 0x80733A00 (3952)
Heap:       0x80733A00 - 0x80797A00 (409600)
Stack:      0x80797A00 - 0x80799A00 (8192)
Text:       0x80700000 - 0x8072F7A4 (194468)
crc_ver_init = 10c
nvram_crc = 10c
Device eth0:  hwaddr 09-10-75-11-03-C4, ipaddr 192.168.1.1, mask 255.255.255.0
        gateway not set, nameserver not set
Loader:raw Filesys:tftp Dev:eth0 File:: Optionsnull)
Loading: Failed.
Could not load :: Timeout occured
Loader:raw Filesys:raw Dev:flash0.os File: Optionsnull)
Loading: ....... 4001926 bytes read
Entry at 0x80001000
Closing network.
Starting program at 0x80001000
Linux version 2.6.22 (root@localhost.localdomain) (gcc version 4.2.3) #128 PREEMPT Wed Mar 6 11:27:10 CST 2013
CPU revision is: 00019749
Found an ST compatible serial flash with 256 64KB blocks; total size 16MB
Determined physical RAM map:
memory: 04000000 @ 00000000 (usable)
Initrd not found or empty - disabling initrd
Built 1 zonelists.  Total pages: 16256
Kernel command line: root=/dev/mtdblock2 console=ttyS0,115200 init=/sbin/preinit
Primary instruction cache 32kB, physically tagged, 4-way, linesize 32 bytes.
Primary data cache 32kB, 4-way, linesize 32 bytes.
Synthesized TLB refill handler (20 instructions).
Synthesized TLB load handler fastpath (32 instructions).
Synthesized TLB store handler fastpath (32 instructions).
Synthesized TLB modify handler fastpath (31 instructions).
PID hash table entries: 256 (order: 8, 1024 bytes)
CPU: BCM5357 rev 1 at 500 MHz
Using 250.000 MHz high precision timer.
Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
Memory: 60280k/65536k available (3072k kernel code, 5196k reserved, 571k data, 264k init, 0k highmem)
Mount-cache hash table entries: 512
NET: Registered protocol family 16
PCI: no core
PCI: no core
PCI: Fixing up bus 0
NET: Registered protocol family 2
Time: MIPS clocksource has been installed.
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 2048 (order: 2, 16384 bytes)
TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
TCP: Hash tables configured (established 2048 bind 2048)
TCP reno registered
squashfs: version 3.2-r2 (2007/01/15) Phillip Lougher
fuse init (API version 7.8)
io scheduler noop registered (default)
Serial: 8250/16550 driver $Revision: 1.1.1.1 $ 4 ports, IRQ sharing disabled
serial8250: ttyS0 at MMIO 0x0 (irq = 8) is a 16550A
RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize
loop: module loaded
PPP generic driver version 2.4.2
PPP Deflate Compression module registered
PPP BSD Compression module registered
PPP MPPE Compression module registered
NET: Registered protocol family 24
PPPoL2TP kernel driver, V1.0
pflash: found no supported devices
sflash: squash filesystem with lzma found at block 23
Creating 4 MTD partitions on "sflash":
0x00000000-0x00020000 : "boot"
0x00020000-0x00ff0000 : "linux"
0x00175290-0x00ff0000 : "rootfs"
0x00ff0000-0x01000000 : "nvram"
nflash: found no supported devices
hbwrr_reg:0
u32 classifier
nf_conntrack version 0.5.0 (1280 buckets, 10240 max)
nf_ct_ftp: registering helper for pf: 2 port: 21
nf_ct_ftp: registering helper for pf: 10 port: 21
ip_tables: (C) 2000-2006 Netfilter Core Team
ClusterIP Version 0.8 loaded successfully
mid :0, nr = 4
mid :1, nr = 12
mid :2, nr = 2
mid :3, nr = 10
mid :4, nr = 34
mid :5, nr = 15
mid :6, nr = 25
mid :7, nr = 12
mid :8, nr = 3
net sniffer init ok.
igd_port_trigger_init:[559]register port trigger
TCP cubic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
mirror create proc success
802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
All bugs added by David S. Miller <davem@redhat.com>
NETCORE fastpath V0.03
VFS: Mounted root (squashfs filesystem) readonly.
Freeing unused kernel memory: 264k freed
Failed to execute /init
Failed to execute /sbin/preinit.  Attempting defaults...
init started:  BusyBox v1.1.2 (2013.01.10-09:08+0000) multi-call binary
Starting pid 15, console /dev/ttyS0: '/etc/rcS'
Algorithmics/MIPS FPU Emulator v1.5
/etc/rcS: /etc/rcS: 2: /var/run: not found
file /var/parame/parame/param.tmp size error 0
emf: module license 'Proprietary' taints kernel.
et_module_init: passivemode set to 0x0
et_module_init: et_txq_thresh set to 0x0
mirror create proc success
eth0: Broadcom BCM47XX 10/100/1000 Mbps Ethernet Controller 6.30.39.31 (r341183)
eth1: Broadcom BCM4329 802.11 Wireless Controller 6.30.39.31 (r341183)
PPTP driver version 0.8.4
klips_info:ipsec_init: KLIPS startup, Openswan KLIPS IPsec stack version: 2.6.38
NET: Registered protocol family 15
KLIPS: registered klips26_rcv_encap function
registered KLIPS /proc/sys/net<6>klips_info:ipsec_alg_init: KLIPS alg v=0.8.1-0 (EALG_MAX=255, AALG_MAX=255)
klips_info:ipsec_alg_init: calling ipsec_alg_static_init()
ipsec_aes_init(alg_type=15 alg_id=12 name=aes): ret=0
ipsec_aes_init(alg_type=14 alg_id=9 name=aes_mac): ret=0
ipsec_3des_init(alg_type=15 alg_id=3 name=3des): ret=0
KLIPS cryptoapi interface: alg_type=15 alg_id=12 name=cbc(aes) keyminbits=128 keymaxbits=256, found(0)
KLIPS cryptoapi interface: alg_type=15 alg_id=253 name=cbc(twofish) keyminbits=128 keymaxbits=256, found(0)
KLIPS cryptoapi interface: alg_type=15 alg_id=252 name=cbc(serpent) keyminbits=128 keymaxbits=256, found(0)
KLIPS cryptoapi interface: alg_type=15 alg_id=6 name=cbc(cast5) keyminbits=128 keymaxbits=128, found(0)
KLIPS cryptoapi interface: alg_type=15 alg_id=7 name=cbc(blowfish) keyminbits=96 keymaxbits=448, found(0)
KLIPS cryptoapi interface: alg_type=15 alg_id=3 name=cbc(des3_ede) keyminbits=192 keymaxbits=192, found(0)
can't add vlan1 to bridge br0: Invalid argument
can't add eth1 to bridge br0: Invalid argument
n_read = 131072
checksum = 2470
cp: /tmp/log: No such file or directory
cp: /bin/ntpara: No such file or directory
parame restroe default
tar: /tmp/param/param.file: No such file or directory
tar: Error exit delayed from previous errors
[tar_flag : 732] : tar OK !

my***

求解决方法
ecompressing...done


CFE version 5.100.138.22 based on BBP 1.0.37 for BCM947XX (32bit,SP,LE)
Build Date: Thu Jan 24 14:18:09 CST 2013 (root@robert-virtual-machine)
Copyright (C) 2000-2008 Broadcom Corporation.

Init Arena
Init Devs.
Boot partition size = 131072(0x20000)
Found an ST compatible serial flash with 256 64KB blocks; total size 16MB
et0: Broadcom BCM47XX 10/100/1000 Mbps Ethernet Controller 5.100.138.22
CPU type 0x19749: 500MHz
Tot mem: 65536 KBytes

CFE mem:    0x80700000 - 0x80799A00 (629248)
Data:       0x8072F7B0 - 0x80732A90 (13024)
BSS:        0x80732A90 - 0x80733A00 (3952)
Heap:       0x80733A00 - 0x80797A00 (409600)
Stack:      0x80797A00 - 0x80799A00 (8192)
Text:       0x80700000 - 0x8072F7A4 (194468)

crc_ver_init = 10c
nvram_crc = 10c
Device eth0:  hwaddr 09-10-75-11-03-C4, ipaddr 192.168.1.1, mask 255.255.255.0
        gateway not set, nameserver not set
Loader:raw Filesys:tftp Dev:eth0 File:: Optionsnull)
Loading: Failed.
Could not load :: Timeout occured
Loader:raw Filesys:raw Dev:flash0.os File: Optionsnull)
Loading: ....... 4001926 bytes read
Entry at 0x80001000
Closing network.
Starting program at 0x80001000
Linux version 2.6.22 (root@localhost.localdomain) (gcc version 4.2.3) #128 PREEMPT Wed Mar 6 11:27:10 CST 2013
CPU revision is: 00019749
Found an ST compatible serial flash with 256 64KB blocks; total size 16MB
Determined physical RAM map:
memory: 04000000 @ 00000000 (usable)
Initrd not found or empty - disabling initrd
Built 1 zonelists.  Total pages: 16256
Kernel command line: root=/dev/mtdblock2 console=ttyS0,115200 init=/sbin/preinit
Primary instruction cache 32kB, physically tagged, 4-way, linesize 32 bytes.
Primary data cache 32kB, 4-way, linesize 32 bytes.
Synthesized TLB refill handler (20 instructions).
Synthesized TLB load handler fastpath (32 instructions).
Synthesized TLB store handler fastpath (32 instructions).
Synthesized TLB modify handler fastpath (31 instructions).
PID hash table entries: 256 (order: 8, 1024 bytes)
CPU: BCM5357 rev 1 at 500 MHz
Using 250.000 MHz high precision timer.
Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
Memory: 60280k/65536k available (3072k kernel code, 5196k reserved, 571k data, 264k init, 0k highmem)
Mount-cache hash table entries: 512
NET: Registered protocol family 16
PCI: no core
PCI: no core
PCI: Fixing up bus 0
NET: Registered protocol family 2
Time: MIPS clocksource has been installed.
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 2048 (order: 2, 16384 bytes)
TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
TCP: Hash tables configured (established 2048 bind 2048)
TCP reno registered
squashfs: version 3.2-r2 (2007/01/15) Phillip Lougher
fuse init (API version 7.8)
io scheduler noop registered (default)
Serial: 8250/16550 driver $Revision: 1.1.1.1 $ 4 ports, IRQ sharing disabled
serial8250: ttyS0 at MMIO 0x0 (irq = 8) is a 16550A
RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize
loop: module loaded
PPP generic driver version 2.4.2
PPP Deflate Compression module registered
PPP BSD Compression module registered
PPP MPPE Compression module registered
NET: Registered protocol family 24
PPPoL2TP kernel driver, V1.0
pflash: found no supported devices
sflash: squash filesystem with lzma found at block 23
Creating 4 MTD partitions on "sflash":
0x00000000-0x00020000 : "boot"
0x00020000-0x00ff0000 : "linux"
0x00175290-0x00ff0000 : "rootfs"
0x00ff0000-0x01000000 : "nvram"
nflash: found no supported devices
hbwrr_reg:0
u32 classifier
nf_conntrack version 0.5.0 (1280 buckets, 10240 max)
nf_ct_ftp: registering helper for pf: 2 port: 21
nf_ct_ftp: registering helper for pf: 10 port: 21
ip_tables: (C) 2000-2006 Netfilter Core Team
ClusterIP Version 0.8 loaded successfully
mid :0, nr = 4
mid :1, nr = 12
mid :2, nr = 2
mid :3, nr = 10
mid :4, nr = 34
mid :5, nr = 15
mid :6, nr = 25
mid :7, nr = 12
mid :8, nr = 3
net sniffer init ok.
igd_port_trigger_init:[559]register port trigger
TCP cubic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
mirror create proc success
802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
All bugs added by David S. Miller <davem@redhat.com>
NETCORE fastpath V0.03
VFS: Mounted root (squashfs filesystem) readonly.
Freeing unused kernel memory: 264k freed
Failed to execute /init
Failed to execute /sbin/preinit.  Attempting defaults...
init started:  BusyBox v1.1.2 (2013.01.10-09:08+0000) multi-call binary
Starting pid 15, console /dev/ttyS0: '/etc/rcS'
Algorithmics/MIPS FPU Emulator v1.5
/etc/rcS: /etc/rcS: 2: /var/run: not found
file /var/parame/parame/param.tmp size error 0
emf: module license 'Proprietary' taints kernel.
et_module_init: passivemode set to 0x0
et_module_init: et_txq_thresh set to 0x0
mirror create proc success
eth0: Broadcom BCM47XX 10/100/1000 Mbps Ethernet Controller 6.30.39.31 (r341183)
eth1: Broadcom BCM4329 802.11 Wireless Controller 6.30.39.31 (r341183)
PPTP driver version 0.8.4
klips_info:ipsec_init: KLIPS startup, Openswan KLIPS IPsec stack version: 2.6.38
NET: Registered protocol family 15
KLIPS: registered klips26_rcv_encap function
registered KLIPS /proc/sys/net<6>klips_info:ipsec_alg_init: KLIPS alg v=0.8.1-0 (EALG_MAX=255, AALG_MAX=255)
klips_info:ipsec_alg_init: calling ipsec_alg_static_init()
ipsec_aes_init(alg_type=15 alg_id=12 name=aes): ret=0
ipsec_aes_init(alg_type=14 alg_id=9 name=aes_mac): ret=0
ipsec_3des_init(alg_type=15 alg_id=3 name=3des): ret=0
KLIPS cryptoapi interface: alg_type=15 alg_id=12 name=cbc(aes) keyminbits=128 keymaxbits=256, found(0)
KLIPS cryptoapi interface: alg_type=15 alg_id=253 name=cbc(twofish) keyminbits=128 keymaxbits=256, found(0)
KLIPS cryptoapi interface: alg_type=15 alg_id=252 name=cbc(serpent) keyminbits=128 keymaxbits=256, found(0)
KLIPS cryptoapi interface: alg_type=15 alg_id=6 name=cbc(cast5) keyminbits=128 keymaxbits=128, found(0)
KLIPS cryptoapi interface: alg_type=15 alg_id=7 name=cbc(blowfish) keyminbits=96 keymaxbits=448, found(0)
KLIPS cryptoapi interface: alg_type=15 alg_id=3 name=cbc(des3_ede) keyminbits=192 keymaxbits=192, found(0)
can't add vlan1 to bridge br0: Invalid argument
can't add eth1 to bridge br0: Invalid argument
n_read = 131072
checksum = 2470
cp: /tmp/log: No such file or directory
cp: /bin/ntpara: No such file or directory
parame restroe default
tar: /tmp/param/param.file: No such file or directory
tar: Error exit delayed from previous errors
[tar_flag : 732] : tar OK !

Starting Protocol Module: procfs                           ... OK!
/bin/envram get et0macaddr > /tmp/sbmac =09:10:75:11:03:c4

smai***

已经刷成功。感谢楼主无私奉献

ha***

fyzy0314 发表于 2013-3-8 19:18
/ $ cd tmp
/var/tmp $ tftp -g -r cfe.old 192.168.162.1 cfe.old
tftp -g -r tomato.trx 192.168.162 ...

前面已经提过了，路由器IP必须192.168.1.1  

皓***

樊诚 发表于 2013-3-8 01:28
悲剧 我的rg200e从TT直接刷NR235w 1.7 B5版，然后用你的脚本new236.vbs刷到1.7正式版后 开机有线无线都ping ...

我也是这现象 怎么救?  我是完全按照楼主说的方法做的啊，就是用UE 把 104 改成 144了