救砖TTL刷机，求教还能不能行

1140***

BootROM 1.20
Booting from NAND flash
Step 1: First phase of PEX-PIPE Configuration
Step 2: Configure the desire PIN_PHY_GEN
Step 3 QSGMII enable
Step 4: Configure SERDES MUXes
Step 5: Activate the RX High Impedance Mode  
Step 6: [PEX-Only] PEX-Main configuration (X4 or X1)
Step 6.2: [PEX-Only] PCI Express Link Capabilities
Step 7: [PEX-X4 Only] To create PEX-Link
Steps 7,8,9,10 and 11
Steps 12: [PEX-Only] Last phase of PEX-PIPE ConfigurationSteps 13: Wait 15ms before checking resultsSteps 14: [PEX-Only]  In order to configureSteps 15: [PEX-Only]  In order to configureSteps 16: [PEX-Only] Training Enablestep 17: max_if= 0x7
step 17:  PEX0  pexUnit= 0
** Link is Gen1, check the EP capability
--> 0050
mvPexConfigRead: return addr=0x%x0050
--> 7001
--> 7001
--> A005
--> A005
--> 0010
--> 4C12
Gen2 client!
step 17:  PEX1  pexUnit= 0
** Link is Gen1, check the EP capability
--> 0040
mvPexConfigRead: return addr=0x%x0040
--> 5001
--> 5001
--> 7005
--> 7005
--> 0010
--> DC12
Gen2 client!
step 17:  PEX2  pexUnit= 0
** Link is Gen1, check the EP capability
--> 0040
mvPexConfigRead: return addr=0x%x0040
--> 5001
--> 5001
--> 7005
--> 7005
--> 0010
--> DC12
Gen2 client!
step 17:  PEX3  pexUnit= 0
PEX3 : Detected No Link. Status Reg(0x0004DA64) = 0x00000001
step 17:  PEX4  pexUnit= 1
PEX4 : Detected No Link. Status Reg(0x00081A64) = 0x00000001
step 17:  PEX5  pexUnit= 1
PEX5 : Detected No Link. Status Reg(0x00085A64) = 0x00000001
step 17:  PEX6  pexUnit= 1
PEX6 : Detected No Link. Status Reg(0x00089A64) = 0x00000001
                                                            DDR3 Training Sequence - Ver 4.5.DDR3 Training Sequence - Static MC Init
DDR3 Training Sequence - HW Training Procedure
DDR3 Training Sequence - Switching XBAR Window to FastPath Window
BootROM: Image checksum verification PASSED

__   __                      _ _
|  \/  | __ _ _ ____   _____| | |
| |\/| |/ _` | '__\ \ / / _ \ | |
| |  | | (_| | |   \ V /  __/ | |
|_|  |_|\__,_|_|    \_/ \___|_|_|
         _   _     ____              _
        | | | |   | __ )  ___   ___ | |_
        | | | |___|  _ \ / _ \ / _ \| __|
        | |_| |___| |_) | (_) | (_) | |_
         \___/    |____/ \___/ \___/ \__|
** LOADER **


U-Boot 2011.12 (Nov 20 2013 - 10:52:51) Marvell version: v2011.12 2013_Q1.2

Boot version:v1.2.18

Board: RD-AXP-GP rev 1.0
SoC:   MV78230 B0
       running 2 CPUs
       Custom configuration
CPU:   Marvell PJ4B (584) v7 (Rev 2) LE
       CPU 0
       CPU    @ 1200 [MHz]
       L2     @ 600 [MHz]
       TClock @ 250 [MHz]
       DDR    @ 600 [MHz]
       DDR 32Bit Width, FastPath Memory Access
       DDR ECC Disabled
DRAM:  256 MiB

Map:   Code:            0x0fea7000:0x0ff5db6c
       BSS:             0x0ffef580
       Stack:           0x0f9a6ef8
       Heap:            0x0f9a7000:0x0fea7000

NAND:  Spansion 1Gb(ID=F101) 128 MiB
MMC:   MRVL_MMC: 0
Bad block table found at page 65472, version 0x01
Bad block table found at page 65408, version 0x01


#### auto_recovery ####
[u_env] get auto_recovery == no
[u_env] get auto_recovery == no
[u_env] get boot_part == 2
[u_env] get boot_part_ready == 3
auto_recovery enabled:0, boot_part:2, boot_part_ready:3

PEX 0.0(0): Root Complex Interface, Detected Link X1, GEN 2.0
PEX 0.1(1): Root Complex Interface, Detected Link X1, GEN 2.0
PEX 0.2(2): Root Complex Interface, Detected Link X1, GEN 2.0
PEX 0.3(3): Detected No Link.
PEX 1.0(4): Detected No Link.
PEX 1.1(5): Detected No Link.
PEX 1.2(6): Detected No Link.

boot_end Offset: 0x100000
u_env_off Offset: 0x100000
s_env_off Offset: 0x140000
devinfo Offset: 0x900000

===================
total_badCount: 0
boot_badCount: 0
u_env_badCount: 0
s_env_badCount: 0
buff_badCount: 0
===================

FPU initialized to Run Fast Mode.
USB 0: Host Mode
USB 1: Host Mode
USB 2: Device Mode
Modules Detected:
mvEthE6171SwitchBasicInit finished
Net:   mvSysNetaInit enter
set port 0 to rgmii enter
set port 1 to rgmii enter
egiga0 [PRIME], egiga1
modify Phy Status
Hit any key to stop autoboot:  0

NAND read: device 0 offset 0x3200000, size 0x400000
4194304 bytes read: OK
Wrong Image Format for bootm command
ERROR: can't get kernel image!
Marvell>>

zjh***

进来顶一顶楼主

1140***

zjh889 发表于 2015-3-5 22:19
进来顶一顶楼主

谢谢  以救活