|
H大,breed-ar934x-blank版不支持RTL8211
国人N85b AR9344+AR9382+RTL8211E
输出如下
Boot and Recovery Environment for Embedded Devices
Copyright (C) 2016 HackPascal <hackpascal@gmail.com>
Build date 2016-12-19 [git-4243410]
Version 1.1 (r1006)
DRAM: 128MB
Platform: Atheros AR9344 rev 2
Board: Blank
Clocks: CPU: 560MHz, DDR: 450MHz, AHB: 225MHz, Ref: 40MHz
Flash: Macronix MX25L12835E (16MB) on ath79-spi.0
ag71xx-eth: MAC address is invalid, using default settings.
ag71xx-eth: Using MAC address 00:13:74:00:00:01
Waiting for auto-negotiation complete ... Timed out
eth0: Atheros AR8228/AR8229 rev 1
Network started on eth0, inet addr 192.168.1.1, netmask 255.255.255.0
Press any key to interrupt autoboot ... 0
Unable to locate firmware.
Starting breed built-in shell
原厂固件
The device is initializing ...
Loading advanced xboot....
Decompressing advanced xboot..................[OK]
============================================================================
DC DC-Device-default xboot, V0.00
============================================================================
Processor type : AR9350
Processor clock : 266MHz
Memory size : 128MB
Flash size : 16MB
HW Version : Ver.N/A
Input Ctrl+A to access advanced xboot list...
APP is starting...## Booting image at bfa80000 ...
Image Name: Linux Kernel Image
Created: 2012-06-06 11:11:16 UTC
Image Type: MIPS Linux Kernel Image (lzma compressed)
Data Size: 908355 Bytes = 887.1 kB
Load Address: 80002000
Entry Point: 801e1ae0
Verifying Checksum ... OK
Uncompressing Kernel Image ... OK
Starting kernel ...
flash_size_mbytes 16
Booting Atheros AR934x
[ 0.000000] Linux version 2.6.31--LSDK-9.2.0_U7.717 (root@linuxwang) (gcc version 4.3.3 (GCC) ) #1 Fri May 25 12:13:21 CST 2012
[ 0.000000] flash_size passed from bootloader = 16
[ 0.000000] CPU revision is: 0001974c (MIPS 74Kc)
[ 0.000000] ath_sys_frequency: cpu apb ddr apb cpu 532 ddr 400 ahb 200
[ 0.000000] Determined physical RAM map:
[ 0.000000] memory: 02000000 @ 00000000 (usable)
[ 0.000000] User-defined physical RAM map:
[ 0.000000] memory: 08000000 @ 00000000 (usable)
[ 0.000000] Initrd not found or empty - disabling initrd
[ 0.000000] Zone PFN ranges:
[ 0.000000] Normal 0x00000000 -> 0x00008000
[ 0.000000] Movable zone start PFN for each node
[ 0.000000] early_node_map[1] active PFN ranges
[ 0.000000] 0: 0x00000000 -> 0x00008000
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 32512
[ 0.000000] Kernel command line: console=ttyS0,115200 revisionid_base=0x18060090 mem=128M rootfstype=jffs2 root=31:02 init=/sbin/init mtdparts=ath-nor0:512k(u-boot),320k(u-boot-env),9920k(rootfs),1408k(uImage),320k(config),64k(mib0),64k(ART),320k(default),320k(parameter),64k(log),3008k(reseved),64k(manu)
[ 0.000000] PID hash table entries: 512 (order: 9, 2048 bytes)
[ 0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
[ 0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
[ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
[ 0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
[ 0.000000] Writing ErrCtl register=00000000
[ 0.000000] Readback ErrCtl register=00000000
[ 0.000000] Memory: 127060k/131072k available (1935k kernel code, 3824k reserved, 465k data, 152k init, 0k highmem)
[ 0.000000] NR_IRQS:128
[ 0.000000] plat_time_init: plat time init done
[ 0.000000] Calibrating delay loop... 265.21 BogoMIPS (lpj=530432)
[ 0.096000] Mount-cache hash table entries: 512
[ 0.096000] NET: Registered protocol family 16
[ 0.096000] pci_init_board : called
[ 0.404000] PCI init:ath_pcibios_init
[ 0.404000] ath_pcibios_init(298): PCI CMD write: 0x356
[ 0.404000] registering PCI controller with io_map_base unset
[ 0.404000] bio: create slab <bio-0> at 0
[ 0.404000] pci 0000:00:00.0: PME# supported from D0 D1 D3hot
[ 0.404000] pci 0000:00:00.0: PME# disabled
[ 0.404000] Returning IRQ 64
[ 0.404000] NET: Registered protocol family 2
[ 0.404000] IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.408000] TCP established hash table entries: 4096 (order: 3, 32768 bytes)
[ 0.408000] TCP bind hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.408000] TCP: Hash tables configured (established 4096 bind 4096)
[ 0.408000] TCP reno registered
[ 0.408000] NET: Registered protocol family 1
[ 0.408000] ATH GPIOC major 0
[ 0.408000] JFFS2 version 2.2 (ZLIB) (RTIME) (c) 2001-2006 Red Hat, Inc.
[ 0.408000] fuse init (API version 7.12)
[ 0.408000] msgmni has been set to 248
[ 0.408000] io scheduler noop registered
[ 0.408000] io scheduler deadline registered (default)
[ 0.408000] Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled
[ 0.408000] serial8250.0: ttyS0 at MMIO 0xb8020000 (irq = 19) is a 16550A
[ 0.408000] console [ttyS0] enabled
[ 0.712000] brd: module loaded
[ 0.712000] 12 cmdlinepart partitions found on MTD device ath-nor0
[ 0.720000] Creating 12 MTD partitions on "ath-nor0":
[ 0.724000] 0x000000000000-0x000000080000 : "u-boot"
[ 0.732000] 0x000000080000-0x0000000d0000 : "u-boot-env"
[ 0.736000] 0x0000000d0000-0x000000a80000 : "rootfs"
[ 0.740000] 0x000000a80000-0x000000be0000 : "uImage"
[ 0.748000] 0x000000be0000-0x000000c30000 : "config"
[ 0.752000] 0x000000c30000-0x000000c40000 : "mib0"
[ 0.756000] 0x000000c40000-0x000000c50000 : "ART"
[ 0.760000] 0x000000c50000-0x000000ca0000 : "default"
[ 0.768000] 0x000000ca0000-0x000000cf0000 : "parameter"
[ 0.772000] 0x000000cf0000-0x000000d00000 : "log"
[ 0.776000] 0x000000d00000-0x000000ff0000 : "reseved"
[ 0.780000] 0x000000ff0000-0x000001000000 : "manu"
[ 0.788000] TCP cubic registered
[ 0.792000] NET: Registered protocol family 10
[ 0.796000] NET: Registered protocol family 17
[ 0.800000] Bridge firewalling registered
[ 0.804000] 802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
[ 0.812000] All bugs added by David S. Miller <davem@redhat.com>
[ 0.816000] arch/mips/atheros/gpio.c (ath_simple_config_init) JUMPSTART_GPIO: 16
[ 0.824000] ATH_GPIO_OE: 1d30b
[ 0.828000] ATH_GPIO_IN: 32e28
[ 0.832000] ATH_GPIO_OUT: 22000
[ 0.836000] ATH_GPIO_OE: 1d30b
[ 0.836000] ATH_GPIO_IN: 32e38
[ 0.840000] ATH_GPIO_OUT: 22000
[ 0.844000] arch/mips/atheros/gpio.c (ath_simple_config_init) RESET_BUTTON_GPIO: 3
[ 0.852000] request_irq for reset success
[ 0.856000] athwdt_init: Registering WDT success
[ 0.860000] ath_otp_init: Registering OTP success
[ 0.864000] ath_clksw_init: Registering Clock Switch Interface success
[ 3.180000] VFS: Mounted root (jffs2 filesystem) readonly on device 31:2.
[ 3.188000] Freeing unused kernel memory: 152k freed
init started: BusyBox v1.01 (2012.05.25-04:13+0000) multi-call binary
init started: BusyBox v1.01 (2012.05.25-04:13+0000) multi-call binary
Starting pid 16, console /dev/ttyS0: '/etc/rc.d/rcS'
[ 6.352000] athrs_tun_var: module license 'unspecified' taints kernel.
[ 6.360000] Disabling lock debugging due to kernel taint
[ 6.392000] ATHR_GMAC: Length per segment 1536
[ 6.396000] ATHR_GMAC: fifo cfg 3 01f00140
[ 6.400000] ATHR_GMAC: RX TASKLET - Pkts per Intr:100
[ 6.408000] ATHR_GMAC: Mac address for unit 0:bfff0000
[ 6.412000] ATHR_GMAC: 40:40:0d:0a:56:45
[ 6.964000] mac:0 Registering RTL8211e....
[ 6.968000] ATHR_GMAC: Max segments per packet : 1
[ 6.972000] ATHR_GMAC: Max tx descriptor count : 128
[ 6.980000] ATHR_GMAC: Max rx descriptor count : 128
[ 6.984000] ATHR_GMAC: Mac capability flags : 2380
art addr=0xbfc40000
[ 7.324000] ath_hal: 0.9.17.1 (AR5416, AR9380, DEBUG, REGOPS_FUNC, WRITE_EEPROM, 11D)
[ 7.352000] ath_rate_atheros: Copyright (c) 2001-2005 Atheros Communications, Inc, All Rights Reserved
[ 7.380000] ath_dfs: Version 2.0.0
[ 7.380000] Copyright (c) 2005-2006 Atheros Communications, Inc. All Rights Reserved
[ 7.448000] ath_dev: Copyright (c) 2001-2007 Atheros Communications, Inc, All Rights Reserved
[ 7.564000] ath_ahb: 9.2.0_U7.717 (Atheros/multi-bss)
[ 7.572000] Bootstrap clock 40MHz
[ 7.580000] ar9300RadioAttach: Need analog access recipe!!
[ 7.584000]
[ 7.584000] ar9300FlashMap 495 mem:c028c000 add:bfc40000
[ 7.592000] Restoring Cal data from Flash
[ 7.596000] dfs_attach: use DFS enhancements
[ 7.604000] DFS min filter rssiThresh = 18
[ 7.608000] DFS max pulse dur = 151 ticks
[ 7.616000] ath_get_caps[4931] rx chainmask mismatch actual 3 sc_chainmak 0
[ 7.624000] ath_get_caps[4906] tx chainmask mismatch actual 3 sc_chainmak 0
[ 7.640000] SC Callback Registration for wifi0
[ 7.644000] wifi0: Atheros 9340: mem=0xb8100000, irq=2
[ 7.652000] ath_pci: 9.2.0_U7.717 (Atheros/multi-bss)
[ 7.660000] ar9300RadioAttach: Need analog access recipe!!
[ 7.668000]
[ 7.668000] ar9300FlashMap 495 mem:c0290000 add:bfc44000
[ 7.676000] Restoring Cal data from Flash
[ 7.684000] dfs_attach: use DFS enhancements
[ 7.692000] DFS min filter rssiThresh = 18
[ 7.696000] DFS max pulse dur = 151 ticks
[ 7.700000] ath_get_caps[4931] rx chainmask mismatch actual 3 sc_chainmak 0
[ 7.708000] ath_get_caps[4906] tx chainmask mismatch actual 3 sc_chainmak 0
[ 7.724000] SC Callback Registration for wifi1
[ 7.728000] wifi1: Atheros 9380: mem=0xb0000000, irq=64
[ 7.736000] [******WLAN******]init_ath_pci 468 timer_switch:1
/etc/rc.d/rc.wifi: 89: cannot create /proc/sys/dev/ath/htdupieenable: Directory nonexistent
[ 7.788000] dfs_init_radar_filters: Unknown dfs domain 0
[ 7.920000] dfs_init_radar_filters: Unknown dfs domain 0
[ 8.116000] athr_gmac_open 718
[ 8.116000] athr_gmac_ring_alloc Allocated 2048 at 0x86cef800
[ 8.124000] athr_gmac_ring_alloc Allocated 2048 at 0x86cef000
[ 8.428000] WASP ----> RTL8211E PHY
[ 8.432000] Setting Drop CRC Errors, Pause Frames and Length Error frames
[ 8.440000] Setting PHY...
[ 8.444000] eth0 phy RTL8211E address 1 Phy ID 1c:c915
[ 11.940000] RTL8211E: Auto-Negotiation timeout
[ 11.948000] ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 12.156000] device eth0 entered promiscuous mode
[ 12.432000] wlan_vap_create : enter. devhandle=0x87f642c0, opmode=IEEE80211_M_HOSTAP, flags=0x1
[ 12.444000] wlan_vap_create : exit. devhandle=0x87f642c0, opmode=IEEE80211_M_HOSTAP, flags=0x1.
[ 12.452000] VAP device wlan0 created
[ 13.572000]
[ 13.572000] DES SSID SET=grentech11n
[ 13.672000] line =1055:chan_change_enable=0,oldchan=1,newchan=6
[ 13.784000] device wlan0 entered promiscuous mode
[ 13.824000] br0: port 2(wlan0) entering learning state
[ 15.948000] ATH_MAC_TIMER: enet unit:0 is up...
[ 15.952000] RGMii 100Mbps full duplex
[ 15.956000] ATH_MAC_TIMER: done cfg2 0x7115 ifctl 0x10000 miictrl
[ 15.960000] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 15.968000] br0: port 1(eth0) entering learning state
[ 17.968000] wlan_vap_create : enter. devhandle=0x869a42c0, opmode=IEEE80211_M_HOSTAP, flags=0x1
[ 17.980000] wlan_vap_create : exit. devhandle=0x869a42c0, opmode=IEEE80211_M_HOSTAP, flags=0x1.
[ 17.988000] VAP device awlan20 created
[ 19.092000]
[ 19.092000] DES SSID SET=grentech11n
[ 19.196000] line =1055:chan_change_enable=0,oldchan=149,newchan=149
[ 19.304000] device awlan20 entered promiscuous mode
[ 19.320000] br0: port 3(awlan20) entering learning state
[ 25.284000] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 28.268000] version=[1]device name=[AP-XXXX]serial no=[1234567890]
Starting pid 869, console /dev/ttyS0: '/sbin/getty'
[ 28.828000] br0: port 2(wlan0) entering forwarding state
guoren_ap mips #1 Fri May 25 12:13:21 CST 2012 (none)
guoren_ap login: [ 30.972000] br0: port 1(eth0) entering forwarding state
[ 34.324000] br0: port 3(awlan20) entering forwarding state
有解决的办法吗? |
|