|
本帖最后由 ynlczf 于 2015-6-9 20:32 编辑
TL-WDR7500 V3 改了256MB内存(H5PS1G63EFR-S5C),刷了你的Breed只识别了128MB。还有5G没了,刷art和刷回原版固件都没用。QQ344914709
- Boot and Recovery Environment for Embedded Devices
- Copyright (C) 2015 HackPascal <hackpascal@gmail.com>
- Build date 2015-06-04 [git-f607266]
- Version 1.0 (r623)
- DRAM: 128MB
- Platform: Qualcomm Atheros QCA9558 rev 0
- Board: Atheros AP152 reference board
- Clocks: CPU: 900MHz, DDR: 800MHz, AHB: 200MHz, Ref: 40MHz
- Flash: Macronix MX25L12835E (16MB) on ath79-spi
- ag71xx-eth: Using MAC address 00:00:00:00:00:00
- eth0: Atheros AR8327/AR8328 rev 4
- Network started on eth0, inet addr 192.168.1.1, netmask 255.255.255.0
- Press any key to interrupt autoboot ... 0
- Trying to boot firmware from 0x9f020000 ...
- TP-LINK firmware image header detected.
- Image Name: c7000002
- Data Size: 1062900 Bytes
- Load Address: 80060000
- Entry Point: 80060000
- Uncompressing data (LZMA) ... done.
- Flushing cache ... done.
- Starting kernel at 0x80060000...
- [ 0.000000] Linux version 3.10.49 (hackpascal@HackPascalPC) (gcc version 4.8.3 (OpenWrt/Linaro GCC 4.8-2014.04 unknown) ) #48 Sun Sep 28 23:11:59 CST 2014
- [ 0.000000] bootconsole [early0] enabled
- [ 0.000000] CPU revision is: 00019750 (MIPS 74Kc)
- [ 0.000000] SoC: Qualcomm Atheros QCA9558 rev 0
- [ 0.000000] Clocks: CPU:900.000MHz, DDR:800.000MHz, AHB:200.000MHz, Ref:40.000MHz
- [ 0.000000] Determined physical RAM map:
- [ 0.000000] memory: 08000000 @ 00000000 (usable)
- [ 0.000000] Initrd not found or empty - disabling initrd
- [ 0.000000] Zone ranges:
- [ 0.000000] Normal [mem 0x00000000-0x07ffffff]
- [ 0.000000] Movable zone start for each node
- [ 0.000000] Early memory node ranges
- [ 0.000000] node 0: [mem 0x00000000-0x07ffffff]
- [ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
- [ 0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
- [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 32512
- [ 0.000000] Kernel command line: board=ARCHER-C7 console=ttyS0,115200 rootfstype=squashfs,jffs2 noinitrd
- [ 0.000000] PID hash table entries: 512 (order: -1, 2048 bytes)
- [ 0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
- [ 0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
- [ 0.000000] Writing ErrCtl register=00000000
- [ 0.000000] Readback ErrCtl register=00000000
- [ 0.000000] Memory: 126184k/131072k available (2253k kernel code, 4888k reserved, 605k data, 276k init, 0k highmem)
- [ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
- [ 0.000000] NR_IRQS:51
- [ 0.000000] Calibrating delay loop... 449.74 BogoMIPS (lpj=2248704)
- [ 0.060000] pid_max: default: 32768 minimum: 301
- [ 0.060000] Mount-cache hash table entries: 512
- [ 0.070000] NET: Registered protocol family 16
- [ 0.070000] MIPS: machine is TP-LINK Archer C7
- [ 0.080000] ar724x-pci ar724x-pci.0: PCIe link is down
- [ 0.080000] registering PCI controller with io_map_base unset
- [ 0.090000] ar724x-pci ar724x-pci.1: PCIe link is down
- [ 0.090000] registering PCI controller with io_map_base unset
- [ 0.500000] bio: create slab <bio-0> at 0
- [ 0.510000] Switching to clocksource MIPS
- [ 0.510000] NET: Registered protocol family 2
- [ 0.520000] TCP established hash table entries: 1024 (order: 1, 8192 bytes)
- [ 0.520000] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
- [ 0.530000] TCP: Hash tables configured (established 1024 bind 1024)
- [ 0.530000] TCP: reno registered
- [ 0.530000] UDP hash table entries: 256 (order: 0, 4096 bytes)
- [ 0.540000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
- [ 0.550000] NET: Registered protocol family 1
- [ 0.560000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
- [ 0.570000] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
- [ 0.580000] msgmni has been set to 246
- [ 0.580000] io scheduler noop registered
- [ 0.580000] io scheduler deadline registered (default)
- [ 0.590000] Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled
- [ 0.620000] serial8250.0: ttyS0 at MMIO 0x18020000 (irq = 11) is a 16550A
- [ 0.620000] console [ttyS0] enabled, bootconsole disabled
- [ 0.620000] console [ttyS0] enabled, bootconsole disabled
- [ 0.640000] ath79-spi ath79-spi: master is unqueued, this is deprecated
- [ 0.640000] m25p80 spi0.0: found mx25l12805d, expected m25p80
- [ 0.650000] m25p80 spi0.0: mx25l12805d (16384 Kbytes)
- [ 0.660000] 5 tp-link partitions found on MTD device spi0.0
- [ 0.660000] Creating 5 MTD partitions on "spi0.0":
- [ 0.670000] 0x000000000000-0x000000020000 : "u-boot"
- [ 0.670000] 0x000000020000-0x0000001239f4 : "kernel"
- [ 0.680000] mtd: partition "kernel" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
- [ 0.690000] 0x0000001239f4-0x000000ff0000 : "rootfs"
- [ 0.700000] mtd: partition "rootfs" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
- [ 0.710000] mtd: device 2 (rootfs) set to be root filesystem
- [ 0.720000] 1 squashfs-split partitions found on MTD device rootfs
- [ 0.720000] 0x000000a70000-0x000000ff0000 : "rootfs_data"
- [ 0.730000] 0x000000ff0000-0x000001000000 : "art"
- [ 0.730000] 0x000000020000-0x000000ff0000 : "firmware"
- [ 0.770000] switch0: Atheros AR8327 rev. 4 switch registered on ag71xx-mdio.0
- [ 2.020000] libphy: ag71xx_mdio: probed
- [ 2.570000] ag71xx ag71xx.0: connected to PHY at ag71xx-mdio.0:00 [uid=004dd034, driver=Atheros AR8216/AR8236/AR8316]
- [ 2.590000] eth0: Atheros AG71xx at 0xb9000000, irq 4, mode:RGMII
- [ 3.140000] eth1: Atheros AG71xx at 0xba000000, irq 5, mode:SGMII
- [ 3.150000] TCP: cubic registered
- [ 3.160000] NET: Registered protocol family 17
- [ 3.160000] 8021q: 802.1Q VLAN Support v1.8
- [ 3.170000] PCI host bridge to bus 0000:00
- [ 3.170000] pci_bus 0000:00: root bus resource [mem 0x10000000-0x11ffffff]
- [ 3.180000] pci_bus 0000:00: root bus resource [io 0x0000]
- [ 3.190000] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]
- [ 3.200000] PCI host bridge to bus 0000:01
- [ 3.200000] pci_bus 0000:01: root bus resource [mem 0x12000000-0x13ffffff]
- [ 3.210000] pci_bus 0000:01: root bus resource [io 0x0001]
- [ 3.210000] pci_bus 0000:01: No busn resource found for root bus, will use [bus 01-ff]
- [ 3.230000] VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
- [ 3.230000] Freeing unused kernel memory: 276K (8032b000 - 80370000)
- procd: Console is alive
- procd: - watchdog -
- [ 7.520000] usbcore: registered new interface driver usbfs
- [ 7.520000] usbcore: registered new interface driver hub
- [ 7.530000] usbcore: registered new device driver usb
- [ 7.550000] SCSI subsystem initialized
- [ 7.560000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
- [ 7.570000] ehci-platform: EHCI generic platform driver
- [ 7.580000] ehci-platform ehci-platform.0: EHCI Host Controller
- [ 7.580000] ehci-platform ehci-platform.0: new USB bus registered, assigned bus number 1
- [ 7.590000] ehci-platform ehci-platform.0: TX-TX IDP fix enabled
- [ 7.600000] ehci-platform ehci-platform.0: irq 48, io mem 0x1b000000
- [ 7.620000] ehci-platform ehci-platform.0: USB 2.0 started, EHCI 1.00
- [ 7.620000] hub 1-0:1.0: USB hub found
- [ 7.630000] hub 1-0:1.0: 1 port detected
- [ 7.630000] ehci-platform ehci-platform.1: EHCI Host Controller
- [ 7.640000] ehci-platform ehci-platform.1: new USB bus registered, assigned bus number 2
- [ 7.650000] ehci-platform ehci-platform.1: TX-TX IDP fix enabled
- [ 7.650000] ehci-platform ehci-platform.1: irq 49, io mem 0x1b400000
- [ 7.680000] ehci-platform ehci-platform.1: USB 2.0 started, EHCI 1.00
- [ 7.680000] hub 2-0:1.0: USB hub found
- [ 7.690000] hub 2-0:1.0: 1 port detected
- [ 7.690000] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
- [ 7.700000] usbcore: registered new interface driver usb-storage
- procd: - preinit -
- [ 8.540000] eth1: link up (1000Mbps/Full duplex)
- Press the [f] key and hit [enter] to enter failsafe mode
- Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level
- kmod: ran 1 iterations
- [ 12.270000] jffs2: notice: (369) jffs2_build_xattr_subsystem: complete building xattr subsystem, 1 of xdatum (0 unchecked, 0 orphan) and 25 of xref (0 dead, 0 orphan) found.
- block: extroot: no root or overlay mount defined
- jffs2 is ready
- jffs2 is ready
- [ 12.390000] jffs2: notice: (366) jffs2_build_xattr_subsystem: complete building xattr subsystem, 1 of xdatum (0 unchecked, 0 orphan) and 25 of xref (0 dead, 0 orphan) found.
- switching to overlay
- 6+0 records in
- 6+0 records out
- 2104+0 records in
- 2104+0 records out
- [ 12.470000] eth1: link down
- procd: - early -
- procd: - watchdog -
- procd: - ubus -
- procd: - init -
- Please press Enter to activate this console.
- [ 14.960000] NET: Registered protocol family 10
- [ 14.990000] RPC: Registered named UNIX socket transport module.
- [ 14.990000] RPC: Registered udp transport module.
- [ 15.000000] RPC: Registered tcp transport module.
- [ 15.000000] RPC: Registered tcp NFSv4.1 backchannel transport module.
- [ 15.070000] Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
- [ 15.080000] nf_conntrack version 0.5.0 (1975 buckets, 7900 max)
- [ 15.110000] ip6_tables: (C) 2000-2006 Netfilter Core Team
- [ 15.120000] Loading modules backported from Linux version master-2014-05-22-0-gf2032ea
- [ 15.130000] Backport generated by backports.git backports-20140320-37-g5c33da0
- [ 15.170000] cfg80211: Calling CRDA to update world regulatory domain
- [ 15.170000] cfg80211: World regulatory domain updated:
- [ 15.180000] cfg80211: DFS Master region: unset
- [ 15.180000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time)
- [ 15.190000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
- [ 15.200000] cfg80211: (2457000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
- [ 15.210000] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (N/A, 2000 mBm), (N/A)
- [ 15.220000] cfg80211: (5170000 KHz - 5250000 KHz @ 160000 KHz), (N/A, 2000 mBm), (N/A)
- [ 15.230000] cfg80211: (5250000 KHz - 5330000 KHz @ 160000 KHz), (N/A, 2000 mBm), (0 s)
- [ 15.230000] cfg80211: (5490000 KHz - 5730000 KHz @ 160000 KHz), (N/A, 2000 mBm), (0 s)
- [ 15.240000] cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A)
- [ 15.250000] cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 0 mBm), (N/A)
- [ 15.300000] u32 classifier
- [ 15.300000] input device check on
- [ 15.300000] Actions configured
- [ 15.340000] Mirror/redirect action on
- [ 15.340000] fuse init (API version 7.22)
- [ 15.380000] ip_tables: (C) 2000-2006 Netfilter Core Team
- [ 15.430000] usbcore: registered new interface driver rt73usb
- [ 15.460000] usbcore: registered new interface driver rtl8187
- [ 15.480000] usbcore: registered new interface driver ums-alauda
- [ 15.480000] usbcore: registered new interface driver ums-cypress
- [ 15.500000] usbcore: registered new interface driver ums-datafab
- [ 15.500000] usbcore: registered new interface driver ums-freecom
- [ 15.530000] usbcore: registered new interface driver ums-isd200
- [ 15.530000] usbcore: registered new interface driver ums-jumpshot
- [ 15.560000] usbcore: registered new interface driver ums-karma
- [ 15.560000] usbcore: registered new interface driver ums-sddr09
- [ 15.580000] usbcore: registered new interface driver ums-sddr55
- [ 15.580000] usbcore: registered new interface driver ums-usbat
- [ 15.600000] usbcore: registered new interface driver usblp
- [ 15.620000] usbcore: registered new interface driver usbserial
- [ 15.620000] usbcore: registered new interface driver usbserial_generic
- [ 15.630000] usbserial: USB Serial support registered for generic
- [ 15.650000] Driver for 1-wire Dallas network protocol.
- [ 15.700000] xt_time: kernel timezone is -0000
- [ 15.710000] usbcore: registered new interface driver ath9k_htc
- [ 15.720000] usbcore: registered new interface driver ch341
- [ 15.730000] usbserial: USB Serial support registered for ch341-uart
- [ 15.740000] usbcore: registered new interface driver pl2303
- [ 15.750000] usbserial: USB Serial support registered for pl2303
- [ 15.750000] PPP generic driver version 2.4.2
- [ 15.760000] NET: Registered protocol family 24
- [ 15.770000] usbcore: registered new interface driver rt2800usb
- [ 15.800000] ath: Invalid EEPROM contents
- [ 15.800000] ath9k qca955x_wmac: failed to initialize device
- [ 15.810000] ath9k: probe of qca955x_wmac failed with error -22
- [ 15.820000] usbcore: registered new interface driver qcserial
- [ 15.830000] usbserial: USB Serial support registered for Qualcomm USB modem
- [ 15.840000] usbcore: registered new interface driver rtl8192cu
- [ 21.950000] eth1: link up (1000Mbps/Full duplex)
- [ 21.950000] device eth1 entered promiscuous mode
- [ 21.980000] IPv6: ADDRCONF(NETDEV_UP): br-lan: link is not ready
- [ 22.000000] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
- [ 22.950000] br-lan: port 1(eth1) entered forwarding state
- [ 22.950000] br-lan: port 1(eth1) entered forwarding state
- [ 23.020000] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
- [ 23.670000] eth0: link up (1000Mbps/Full duplex)
- [ 23.690000] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
- [ 24.950000] br-lan: port 1(eth1) entered forwarding state
- procd: - init complete -
复制代码
|
|