找回密码
 立即注册

QQ登录

只需一步,快速开始

搜索
广告投放联系QQ68610888
楼主: hackpascal

【2022-07-26】AR/QCA/MTK Breed,功能强大的多线程 Bootloader

   火... [复制链接]
发表于 2015-7-25 18:17 | 显示全部楼层
aximpda 发表于 2015-7-24 23:40
拨电源后,可以重启进入正常状态?

我的表述有问题,应该表述为:拔电源后,重新插上,可以正常启动。
我的恩山、我的无线 The best wifi forum is right here.
回复

使用道具 举报

发表于 2015-7-25 22:46 | 显示全部楼层
本帖最后由 coool 于 2015-7-25 22:48 编辑

我是4530R,用的是之前的不死uboot,现在想刷breed,有几点疑问:
1)AR 芯片从不死 U-Boot 更新  Breed 方法:请到 http://breed.hackpascal.net/r585%20%5b2015-05-13%5d/ 下载 r585 版的 Breed 刷入,再刷入最新版的 Breed。
这个怎么理解?在uboot中先刷r585 版的 Breed,先不要重启,直接再刷最新版的breed?

2)刷 AR/QCA 的 breed 后请修改 MAC 地址!
这个怎么理解?在uboot中刷完breed以后,先不重启,修改MAC以后再重启?
3)在Uboot中刷breed,需不需ART同时一起刷?

谢谢!
我的恩山、我的无线 The best wifi forum is right here.
回复

使用道具 举报

发表于 2015-7-25 23:10 | 显示全部楼层
顶一个~以前的MW150R用过UBOOT,但是刷坏了,这次的FIR302M完全没问题~
我的恩山、我的无线 The best wifi forum is right here.
回复

使用道具 举报

发表于 2015-7-26 11:29 | 显示全部楼层
刷了最新Bootloader,小米mini路由可以刷入最新固件了,不过刷入的小米固件却无法正常工作,也设置了小米固件启动.表现为无法获取IP地址,路由网关也不通.是不是要刷回小米官方的不死uboot才可以?
我的恩山、我的无线 The best wifi forum is right here.
回复

使用道具 举报

发表于 2015-7-26 11:59 | 显示全部楼层
hackpascal 发表于 2015-3-21 22:38
更新日志

[2015-07-19 r647]

老大,新版的boot怎么超频阿?9331的
我的恩山、我的无线 The best wifi forum is right here.
回复

使用道具 举报

发表于 2015-7-26 19:09 | 显示全部楼层
你好,楼主,我的机器是网件1000V2,麻烦看下我这是什么问题?boot是编程器刷进去的,正常进入刷机WEB,也正常刷入了UBNT,可以时入UBNT主页,有输入帐号和密码窗口,但进入主页出下如下错误,请指示,在页面的左上角,谢谢。
settings.inc: (6)Unable to open: /etc/board.inc on line 90
include("/etc/board.inc");
settings.inc: Include error: 2 No such file or directory on line 90
include("/etc/board.inc");
settings.inc: (6)Unable to open: lib/oem.inc on line 91
include("lib/oem.inc");
settings.inc: Include error: 2 No such file or directory on line 91
include("lib/oem.inc");
login.cgi: (6)Unable to open: lib/l10n.inc on line 4
include("lib/l10n.inc");
login.cgi: Include error: 2 No such file or directory on line 4
include("lib/l10n.inc");
我的恩山、我的无线 The best wifi forum is right here.
回复

使用道具 举报

发表于 2015-7-27 14:45 | 显示全部楼层
741N V1刷了breed根本不能進入uboot
我的恩山、我的无线 The best wifi forum is right here.
回复

使用道具 举报

发表于 2015-7-27 19:51 | 显示全部楼层
本帖最后由 coool 于 2015-7-27 20:19 编辑

4530R 更新了最新的R647以后,5G信号变得很差。恢复会R585 5G信号才恢复到以前正常强度。
我的恩山、我的无线 The best wifi forum is right here.
回复

使用道具 举报

发表于 2015-7-27 23:47 | 显示全部楼层
本帖最后由 joe1203a 于 2015-7-28 08:21 编辑

楼主你好
在wdr7500 v3,
uboot + wdr7500 v3  (20150423) 或 Archer C7 (150304) = 2.4G及5G也能用
breed + wdr7500 v3  (20150423) 或 Archer C7 (150304) = 只有2.4G能用
以下是uboot+ wdr7500 v3  (20150423)  及breed + Archer C7 (150304) 的TTL输出 (MAC地址改为 xx:xx:xx:xx:xx:xx)

  1. U-Boot 1.1.4 (Apr 23 2015 - 13:39:44)

  2. ap135 - Scorpion 1.0DRAM:
  3. sri
  4. Scorpion 1.0
  5. ath_ddr_initial_config(178): (32bit) ddr2 init
  6. tap = 0x00000003
  7. Tap (low, high) = (0x2, 0x1b)
  8. Tap values = (0xe, 0xe, 0xe, 0xe)
  9. 128 MB
  10. Flash Manuf Id 0xef, DeviceId0 0x40, DeviceId1 0x17
  11. flash size 8MB, sector count = 128
  12. Flash:  8 MB
  13. Using default environment

  14. *** Warning *** : PCIe WLAN Module not found !!!
  15. In:    serial
  16. Out:   serial
  17. Err:   serial
  18. Net:   ath_gmac_enet_initialize...
  19. athrs_sgmii_res_cal: cal value = 0xe
  20. No valid address in Flash. Using fixed address
  21. No valid address in Flash. Using fixed address
  22. ath_gmac_enet_initialize: reset mask:c02200
  23. Scorpion  ----> S17 PHY *
  24. athrs17_reg_init: complete
  25. : cfg1 0x80000000 cfg2 0x7114
  26. eth0: ba:be:fa:ce:08:41
  27. eth0 up
  28. athrs17_reg_init_wan done
  29. SGMII in forced mode
  30. athr_gmac_sgmii_setup SGMII done
  31. : cfg1 0x800c0000 cfg2 0x7214
  32. eth1: ba:be:fa:ce:08:41
  33. eth1 up
  34. eth0, eth1
  35. Setting 0x18116290 to 0x50a1214f
  36. Autobooting in 1 seconds
  37. ## Booting image at 9f020000 ...
  38.    Uncompressing Kernel Image ... OK

  39. Starting kernel ...

  40. Booting QCA955x
  41. Linux version 2.6.31--LSDK-9.2.0_U6.616 (tplink@localhost.localdomain) (gcc version 4.3.3 (GCC) ) #1 Thu Apr 23 13:43:15 CST 2015
  42. Ram size passed from bootloader =128M
  43. flash_size passed from bootloader = 8
  44. CPU revision is: 00019750 (MIPS 74Kc)
  45. cpu apb ddr apb ath_sys_frequency: cpu 720 ddr 600 ahb 200
  46. Determined physical RAM map:
  47. memory: 08000000 @ 00000000 (usable)
  48. Zone PFN ranges:
  49.   Normal   0x00000000 -> 0x00008000
  50. Movable zone start PFN for each node
  51. early_node_map[1] active PFN ranges
  52.     0: 0x00000000 -> 0x00008000
  53. Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 32512
  54. Kernel command line: console=ttyS0,115200 root=31:02 rootfstype=squashfs init=/sbin/init mtdparts=ath-nor0:128k(u-boot),1024k(kernel),6912k(rootfs),64k(config),64k(ART) mem=128M
  55. PID hash table entries: 512 (order: 9, 2048 bytes)
  56. Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
  57. Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
  58. Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
  59. Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
  60. Writing ErrCtl register=00000000
  61. Readback ErrCtl register=00000000
  62. Memory: 112868k/131072k available (1891k kernel code, 18036k reserved, 441k data, 120k init, 0k highmem)
  63. NR_IRQS:128
  64. plat_time_init: plat time init done
  65. Calibrating delay loop... 359.42 BogoMIPS (lpj=718848)
  66. Mount-cache hash table entries: 512

  67. ****************ALLOC***********************
  68. Packet mem: 802794e0 (0xe00000 bytes)
  69. ********************************************

  70. NET: Registered protocol family 16
  71. ath_pcibios_init: bus 0
  72. ***** Warning PCIe 0 H/W not found !!!
  73. registering PCI controller with io_map_base unset
  74. ath_pcibios_init: bus 1
  75. ath_pcibios_init(232): PCI 1 CMD write: 0x356
  76. registering PCI controller with io_map_base unset
  77. ===@@@@@@@@@@@=>use GPIO13 as wifi button control!
  78. bio: create slab <bio-0> at 0
  79. pcibios_map_irq: IRQ 76 for bus 1
  80. NET: Registered protocol family 2
  81. IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
  82. TCP established hash table entries: 4096 (order: 3, 32768 bytes)
  83. TCP bind hash table entries: 4096 (order: 2, 16384 bytes)
  84. TCP: Hash tables configured (established 4096 bind 4096)
  85. TCP reno registered
  86. NET: Registered protocol family 1
  87. ATH GPIOC major 0
  88. squashfs: version 4.0 (2009/01/31) Phillip Lougher
  89. msgmni has been set to 220
  90. Block layer SCSI generic (bsg) driver version 0.4 loaded (major 254)
  91. io scheduler noop registered
  92. io scheduler deadline registered (default)
  93. Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled
  94. serial8250.0: ttyS0 at MMIO 0xb8020000 (irq = 19) is a 16550A
  95. console [ttyS0] enabled
  96. PPP generic driver version 2.4.2
  97. NET: Registered protocol family 24
  98. 5 cmdlinepart partitions found on MTD device ath-nor0
  99. Creating 5 MTD partitions on "ath-nor0":
  100. 0x000000000000-0x000000020000 : "u-boot"
  101. 0x000000020000-0x000000120000 : "kernel"
  102. 0x000000120000-0x0000007e0000 : "rootfs"
  103. 0x0000007e0000-0x0000007f0000 : "config"
  104. 0x0000007f0000-0x000000800000 : "ART"
  105. ->Oops: flash id 0xef4017 .
  106. Ooops, why the devices couldn't been initialed?
  107. TCP cubic registered
  108. NET: Registered protocol family 10
  109. NET: Registered protocol family 17
  110. 802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
  111. All bugs added by David S. Miller <davem@redhat.com>
  112. athwdt_init: Registering WDT success
  113. ath_otp_init: Registering OTP success
  114. VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
  115. Freeing unused kernel memory: 120k freed
  116. init started:  BusyBox v1.01 (2015.04.23-05:49+0000) multi-call binary
  117. This Board use 2.6.31
  118. xt_time: kernel timezone is -0000
  119. nf_conntrack version 0.5.0 (2048 buckets, 81920 max)
  120. CONFIG_NF_CT_ACCT is deprecated and will be removed soon. Please use
  121. nf_conntrack.acct=1 kernel parameter, acct=1 nf_conntrack module option or
  122. sysctl net.netfilter.nf_conntrack_acct=1 to enable it.
  123. ip_tables: (C) 2000-2006 Netfilter Core Team
  124. insmod: cannot open module `/lib/modules/2.6.31/kernel/iptable_raw.ko': No such file or directory
  125. insmod: cannot open module `/lib/modules/2.6.31/kernel/flashid.ko': No such file or directory
  126. PPPoL2TP kernel driver, V1.0
  127. PPTP driver version 0.8.3
  128. insmod: cannot open module `/lib/modules/2.6.31/kernel/harmony.ko': No such file or directory

  129. (none) mips #1 Thu Apr 23 13:43:15 CST 2015 (none)
  130. (none) login: qca955x_GMAC: Length per segment 1536
  131. 955x_GMAC: qca955x_gmac_attach
  132. 955x_GMAC: qca955x_set_gmac_caps
  133. Currently in polling mode unit1
  134. mac:1 Registering S17....
  135. qca955x_GMAC: RX TASKLET - Pkts per Intr:200
  136. qca955x_GMAC: Max segments per packet :   1
  137. qca955x_GMAC: Max tx descriptor count :   220
  138. qca955x_GMAC: Max rx descriptor count :   220
  139. qca955x_GMAC: Mac capability flags    :   12002200
  140. 955x_GMAC: qca955x_gmac_attach
  141. 955x_GMAC: qca955x_set_gmac_caps
  142. Currently in polling mode unit0
  143. mac:0 Registering S17....
  144. qca955x_GMAC: RX TASKLET - Pkts per Intr:200
  145. qca955x_GMAC: Max segments per packet :   1
  146. qca955x_GMAC: Max tx descriptor count :   220
  147. qca955x_GMAC: Max rx descriptor count :   220
  148. qca955x_GMAC: Mac capability flags    :   10002A00
  149. 955x_GMAC: Serdes PLL is locked value 0x1f038116
  150. athr_gmac_ring_alloc Allocated 3520 at 0x87950000
  151. athr_gmac_ring_alloc Allocated 3520 at 0x87a99000
  152. 955x_GMAC: eth1 in SGMII MODE
  153. Scorpion -----> S17 PHY
  154. ttl zero adding rule #0
  155. ACL is not yet enabled. Enabling...
  156. ttl one adding rule #1
  157. UDP checksum 0 adding rule #3
  158. Hello, nat helper module for 1.08!
  159. netlink_kernel_create succeeded at tp_rule_nl_prot: [29]

  160. ######## S17 SSDK init succeeded! ########
  161. _athrs17_mac0_intf SGMII done
  162. athrs17_reg_init:done
  163. 955x_SGMII::athr_gmac_sgmii_setup  Done
  164. Setting Drop CRC Errors, Pause Frames and Length Error frames
  165. Setting PHY...
  166. Phy setup Complete
  167. ADDRCONF(NETDEV_UP): eth0: link is not ready
  168. device eth0.1 entered promiscuous mode
  169. device eth0 entered promiscuous mode
  170. SET INTF MAC 0:ec-26-ca-f0-0e-c8
  171. SET INTF MAC 1:ec-26-ca-f0-0e-c9
  172. br0: port 1(eth0.1) entering forwarding state
  173. Adding ACL rules 2 - wan to lan, dst ip is lan net
  174. nf_conntrack_rtsp v0.6.21 loading
  175. nf_nat_rtsp v0.6.21 loading
  176. adf: module license 'Proprietary' taints kernel.
  177. Disabling lock debugging due to kernel taint
  178. ath_hal: 0.9.17.1 (AR5416, AR9380, REGOPS_FUNC, WRITE_EEPROM, 11D)
  179. ath_rate_atheros: Copyright (c) 2001-2005 Atheros Communications, Inc, All Rights Reserved
  180. ath_dfs: Version 2.0.0
  181. Copyright (c) 2005-2006 Atheros Communications, Inc. All Rights Reserved
  182. ath_dev: Copyright (c) 2001-2007 Atheros Communications, Inc, All Rights Reserved
  183. ath_ahb: 10.1.467 (Atheros/multi-bss)
  184. __ath_attach: Set global_scn[0]
  185. Enterprise mode: 0x43fc0000
  186. Restoring Cal data from Flash
  187. Green-AP : Green-AP : Attached

  188. ath_get_caps[5956] rx chainmask mismatch actual 7 sc_chainmak 0
  189. ath_get_caps[5931] tx chainmask mismatch actual 7 sc_chainmak 0
  190. ath_attach_dfs[11935] dfsdomain 1
  191. SC Callback Registration for wifi0
  192. wifi0: Atheros ???: mem=0xb8100000, irq=2
  193. ath_pci: 10.1.467 (Atheros/multi-bss)
  194. ath_pci_probe
  195. PCI device id is 003c :003c
  196. ath_pci 0000:01:00.0: ath DEBUG: sc=0x86ebbe00

  197. ol_ath_pci_configure : num_desired MSI set to 0

  198. Using PCI Legacy Interrupt
  199. __ol_ath_attach: ath_attach TODO
  200. ol_ath_attach() BMI inited.
  201. ol_ath_attach() BMI Get Target Info.
  202. ol_ath_attach() TARGET TYPE: 7 Vers 0x4100016c
  203. NUM_DEV=1 FWMODE=0x2 FWSUBMODE=0x0 FWBR_BUF 0
  204. ol_ath_attach() configure Target .
  205. qc98xx_verify_checksum: flash checksum passed: 0xb25f
  206. ol_transfer_bin_file 1688: Download Flash data len 2116
  207. ol_transfer_bin_file 1635: Download Firmware data len 190448
  208. ol_ath_attach() Download FW.
  209. ol_ath_attach() HT Create .
  210. ol_ath_attach() HIF Claim.
  211. ol_ath_attach() BMI Done.
  212. ol_ath_attach() WMI attached. wmi_handle 86e30000
  213. +HWT
  214. CE_recv_buf_enqueue 457 Populate last entry 512 for CE 5
  215. CE_recv_buf_enqueue 466 CE 5 wi 511 dest_ptr 0x5eb500 nbytes 0 recv_ctxt 0x86c34800
  216. -HWT
  217. HTC Service:0x0300 ep:1 TX flow control disabled
  218. CE_pkt_dl_len_set CE 4 Pkt download length 42
  219. TXRX: Created pdev 86ebb800
  220. wmi_service_ready_event_rx:  WMI UNIFIED SERVICE READY event
  221. num_rf_chain : 00000003
  222. ht_cap_info: : 0000085b
  223. vht_cap_info : 338001b2
  224. vht_supp_mcs : 0000ffea
  225. LARGE_AP enabled. num_peers 144, num_vdevs 16, num_tids 256
  226. idx 0 req 1  num_units 0 num_unit_info 2 unit size 404 actual units 145
  227. chunk 0 len 58580 requested ,ptr  0x6f20000
  228. FIRMWARE:P 145 V 16 T 443

  229. wmi_ready_event_rx:  WMI UNIFIED READY event
  230. ol_ath_connect_htc() WMI is ready
  231. ol_ath_set_host_app_area TODO
  232. target uses HTT version 2.1; host uses 2.1
  233. ol_ath_attach() connect HTC.
  234. ol_regdmn_start: reg-domain param: regdmn=0, countryName=, wModeSelect=FFFFFFFF, netBand=FFFFFFFF, extendedChanMode=0.
  235. ol_regdmn_init_channels: !avail mode 0x1f9001 (0x2) flags 0x2150
  236. ol_regdmn_init_channels: !avail mode 0x1f9001 (0x4) flags 0xa0
  237. ol_regdmn_init_channels: !avail mode 0x1f9001 (0x8) flags 0xc0
  238. ol_regdmn_init_channels: !avail mode 0x1f9001 (0x20) flags 0xd0
  239. ol_regdmn_init_channels: !avail mode 0x1f9001 (0x40) flags 0x150
  240. ol_regdmn_init_channels: !avail mode 0x1f9001 (0x800) flags 0x10080
  241. ol_regdmn_init_channels: !avail mode 0x1f9001 (0x2000) flags 0x20080
  242. ol_regdmn_init_channels: !avail mode 0x1f9001 (0x4000) flags 0x40080
  243. Skipping VHT80 channel 5825
  244. ol_ath_phyerr_attach: called
  245. OL Resmgr Init-ed
  246. Green-AP : Green-AP : Attached

  247. Green-AP : Attached
  248. ol_if_dfs_setup: called
  249. ol_if_dfs_attach: called; ptr=86f09974, radar_info=87bd7be8
  250. ol_ath_rtt_meas_report_attach: called
  251. ol_ath_attach() UMAC attach .
  252. ol_if_dfs_configure: called
  253. ol_if_dfs_configure: FCC domain
  254. ol_if_dfs_disable: called
  255. ol_ath_attach: Calling ol_if_dfs_configure
  256. __ol_ath_attach: init tx/rx TODO
  257. __ol_ath_attach: hard_header_len reservation 58
  258. __ol_ath_attach: dev name wifi1
  259. SC Callback Registration for wifi1
  260. ath_attach_dfs[11935] dfsdomain 1
  261. VAP device ath0 created

  262. DES SSID SET=TP-LINK_0EC7
  263. ieee80211_ioctl_siwmode: imr.ifm_active=131712, new mode=3, valid=1
  264. Invoking ACS module for Best channel selection
  265. Channel 1 average beacon RSSI 37 noisefloor -107  ieee80211_acs_find_best_11ng_centerchan chan: 1 beacon RSSI + weighted noisefloor: -177
  266. Channel 6 average beacon RSSI 13 noisefloor -106  ieee80211_acs_find_best_11ng_centerchan chan: 6 beacon RSSI + weighted noisefloor: -199
  267. Channel 6 average beacon RSSI 13 noisefloor -106  ieee80211_acs_find_best_11ng_centerchan chan: 6 beacon RSSI + weighted noisefloor: -199
  268. Channel 11 average beacon RSSI 13 noisefloor -107  ieee80211_acs_find_best_11ng_centerchan chan: 11 beacon RSSI + weighted noisefloor: -201
  269. ieee80211_acs_find_best_11ng_centerchan found best 11ng center chan: 11 rssi: -201
  270. athr_gmac_ring_alloc Allocated 3520 at 0x86f07000
  271. athr_gmac_ring_alloc Allocated 3520 at 0x87a36000
  272. 955x_GMAC: eth0 in RGMII MODE
  273. Scorpion -----> S17 PHY
  274. athrs17_reg_init_wan done
  275. Setting Drop CRC Errors, Pause Frames and Length Error frames
  276. Setting PHY...
  277. ADDRCONF(NETDEV_UP): eth1: link is not ready
  278. device eth1 entered promiscuous mode
  279. device ath0 entered promiscuous mode
  280. br1: port 2(ath0) entering forwarding state
  281. ieee80211_ioctl_siwmode: imr.ifm_active=1442432, new mode=3, valid=1
  282. br1: port 2(ath0) entering disabled state
  283. DEVICE IS DOWN ifname=ath0
  284. DEVICE IS DOWN ifname=ath0
  285. br1: port 2(ath0) entering forwarding state

  286. Enet:1 port1 up
  287. 955x_GMAC: enet unit:1 is up...
  288. eth1  SGMII  1000Mbps  full duplex
  289. 955x_GMAC: qca955x_soc_gmac_set_mac_duplex
  290. 955x_GMAC: qca955x_soc_gmac_set_link Done
  291. 955x_GMAC: done cfg2 0x7215 ifctl 0x0 miictrl
  292. ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
  293. 955x_GMAC: qca955x_soc_gmac_set_mac_duplex
  294. 955x_GMAC: qca955x_soc_gmac_set_link Done
  295. ADDRCONF(NETDEV_CHANGE): eth1: link becomes ready
  296. br1: port 1(eth1) entering forwarding state
  297. eth1: received packet with own address as source address
  298. br1: port 2(ath0) entering disabled state
  299. br1: port 2(ath0) entering forwarding state
  300. isCountryCodeValid: EEPROM regdomain 0x0
  301. ol_regdmn_init_channels: !avail mode 0x1f9001 (0x2) flags 0x2150
  302. ol_regdmn_init_channels: !avail mode 0x1f9001 (0x4) flags 0xa0
  303. ol_regdmn_init_channels: !avail mode 0x1f9001 (0x8) flags 0xc0
  304. ol_regdmn_init_channels: !avail mode 0x1f9001 (0x20) flags 0xd0
  305. ol_regdmn_init_channels: !avail mode 0x1f9001 (0x40) flags 0x150
  306. ol_regdmn_init_channels: !avail mode 0x1f9001 (0x800) flags 0x10080
  307. ol_regdmn_init_channels: !avail mode 0x1f9001 (0x2000) flags 0x20080
  308. ol_regdmn_init_channels: !avail mode 0x1f9001 (0x4000) flags 0x40080
  309. Skipping VHT80 channel 5825
  310. ath_ioctl: SIOC80211IFCREATE CALLED
  311. wmi_unified_vdev_create_send: ID = 0 VAP Addr = ec:26:ca:f0:0e:c6:
  312. TXRX: Created vdev 86ff1b00 (ec:26:ca:f0:0e:c6)
  313. Setting vdev param = 26, value = 147
  314. Setting vdev param = 27, value = 295
  315. Setting vdev param = 28, value = 300
  316. VAP device ath1 created
  317. TXRX: ol_txrx_peer_find_add_id: peer 8660b000 ID 401
  318. TXRX: ol_txrx_peer_find_add_id: peer 8660b000 ID 385
  319. eth1: received packet with own address as source address
  320. Setting vdev param = f, value = 1
  321. ol_ath_vap_set_param: VAP param unsupported param:80 value:1
  322. ol_ath_vap_set_param: VAP param unsupported param:35 value:0

  323. DES SSID SET=TP-LINK_5G_0EC6
  324. ieee80211_ioctl_siwmode: imr.ifm_active=66176, new mode=3, valid=1
  325. OL vap_stop +
  326. wmi_unified_vdev_stop_send
  327. OL vap_stop -
  328. STOPPED EVENT for vap 0
  329. Setting vdev param = 2a, value = 2
  330. ol_ath_vap_set_param: VAP param is now supported param:62 value:2
  331. OL vap_stop +
  332. wmi_unified_vdev_stop_send
  333. OL vap_stop -
  334. STOPPED EVENT for vap 0
  335. OL vap_stop +
  336. wmi_unified_vdev_stop_send
  337. OL vap_stop -
  338. STOPPED EVENT for vap 0
  339. FWLOG: [29837] WHAL_ERROR_RECV_STOPPCU ( 0x110298a, 0x3 )
  340. FWLOG: [29837] WHAL_ERROR_RESET_PM (  )
  341. Invoking ACS module for Best channel selection
  342. Function ieee80211_acs_find_best_11na_centerchan best 5G channel is 161
  343. OL vap_start +
  344. OL vap_start -
  345. ol_vdev_start_resp_ev
  346. ol_ath_vap_join: join operation is only for STA/IBSS mode
  347. ol_ath_wmm_update:
  348. Setting vdev param = 3, value = 100
  349. Notification to UMAC VAP layer
  350. eth1: received packet with own address as source address
  351. wmi_unified_vdev_stop_send
  352. STOPPED EVENT for vap 0
  353. Setting vdev param = 1a, value = 1
  354. Setting vdev param = 3, value = 100
  355. Setting vdev param = d, value = 1
  356. Setting vdev param = 12, value = 1
  357. Setting vdev param = 1e, value = 1
  358. OL vap_stop +
  359. wmi_unified_vdev_stop_send
  360. OL vap_stop -
  361. STOPPED EVENT for vap 0
  362. OL vap_start +
  363. OL vap_start -
  364. ol_vdev_start_resp_ev
  365. ol_ath_vap_join: join operation is only for STA/IBSS mode
  366. ol_ath_wmm_update:
  367. Setting vdev param = 3, value = 100
  368. Notification to UMAC VAP layer
  369. device ath1 entered promiscuous mode
  370. br1: port 3(ath1) entering forwarding state
  371. ieee80211_ioctl_siwmode: imr.ifm_active=131738, new mode=3, valid=1
  372. wmi_unified_vdev_stop_send
  373. STOPPED EVENT for vap 0
  374. br1: port 3(ath1) entering disabled state
  375. ol_ath_vap_set_param: VAP param unsupported param:32 value:0
  376. ol_ath_vap_set_param: VAP param unsupported param:121 value:1
  377. DEVICE IS DOWN ifname=ath1
  378. DEVICE IS DOWN ifname=ath1
  379. ol_ath_vap_set_param: VAP param unsupported param:32 value:0
  380. ol_ath_vap_set_param: VAP param unsupported param:32 value:0
  381. ol_ath_vap_set_param: VAP param unsupported param:17 value:1
  382. OL vap_stop +
  383. wmi_unified_vdev_stop_send
  384. OL vap_stop -
  385. STOPPED EVENT for vap 0
  386. OL vap_start +
  387. OL vap_start -
  388. ol_vdev_start_resp_ev
  389. ol_ath_vap_join: join operation is only for STA/IBSS mode
  390. ol_ath_wmm_update:
  391. Setting vdev param = 3, value = 100
  392. Notification to UMAC VAP layer
  393. br1: port 3(ath1) entering forwarding state
  394. FWLOG: [36702] WAL_DBGID_BB_WDOG_TRIGGERED ( 0x8f5e, 0x200008a, 0x0, 0x5 )
  395. eth1: received packet with own address as source address
  396. wmi_unified_vdev_stop_send
  397. STOPPED EVENT for vap 0
  398. br1: port 3(ath1) entering disabled state
  399. ol_ath_vap_set_param: VAP param unsupported param:17 value:1
  400. OL vap_stop +
  401. wmi_unified_vdev_stop_send
  402. OL vap_stop -
  403. STOPPED EVENT for vap 0
  404. OL vap_start +
  405. OL vap_start -
  406. ol_vdev_start_resp_ev
  407. ol_ath_vap_join: join operation is only for STA/IBSS mode
  408. ol_ath_wmm_update:
  409. Setting vdev param = 3, value = 100
  410. Notification to UMAC VAP layer
  411. br1: port 3(ath1) entering forwarding state
  412. fuse init (API version 7.12)
  413. usbcore: registered new interface driver usbfs
  414. usbcore: registered new interface driver hub
  415. usbcore: registered new device driver usb
  416. ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
  417. Port Status 1c000004
  418. ath-ehci ath-ehci.0: ATH EHCI
  419. ath-ehci ath-ehci.0: new USB bus registered, assigned bus number 1
  420. ehci_reset Intialize USB CONTROLLER in host mode: 13
  421. ehci_reset Port Status 1c000000
  422. ath-ehci ath-ehci.0: irq 3, io mem 0x1b000000
  423. ehci_reset Intialize USB CONTROLLER in host mode: 13
  424. ehci_reset Port Status 1c000000
  425. ath-ehci ath-ehci.0: USB 2.0 started, EHCI 1.00
  426. usb usb1: configuration #1 chosen from 1 choice
  427. hub 1-0:1.0: USB hub found
  428. hub 1-0:1.0: 1 port detected
  429. Port Status 1c000000
  430. ath-ehci1 ath-ehci1.1: ATH EHCI
  431. ath-ehci1 ath-ehci1.1: new USB bus registered, assigned bus number 2
  432. ehci_reset Intialize USB CONTROLLER in host mode: 13
  433. ehci_reset Port Status 1c000000
  434. ath-ehci1 ath-ehci1.1: irq 3, io mem 0x1b400000
  435. ehci_reset Intialize USB CONTROLLER in host mode: 13
  436. ehci_reset Port Status 1c000000
  437. ath-ehci1 ath-ehci1.1: USB 2.0 started, EHCI 1.00
  438. usb usb2: configuration #1 chosen from 1 choice
  439. hub 2-0:1.0: USB hub found
  440. hub 2-0:1.0: 1 port detected
  441. SCSI subsystem initialized
  442. Initializing USB Mass Storage driver...
  443. usbcore: registered new interface driver usb-storage
  444. USB Mass Storage support registered.
  445. GPL NetUSB up!
  446. kc   86 : run_telnetDBGDServer start
  447. kc  223 : init_DebugD end
  448. INFO1758: NetUSB 1.184, 0002061F : May  7 2012 10:35:23
  449. INFO175A:  AUTH ISOC
  450. INFO175B:
  451. usbcore: registered new interface driver KC NetUSB General Driver
  452. INFO0076:  init proc : PAGE_SIZE 4096
  453. INFO17B4: Check mac address
  454. INFO162C:  infomap 8678c220
  455. INFO162F:  sleep to wait br0 to wake up
  456. INFO02D0:  use dev Name br0
  457. INFO1638:  sleep to wait br0 end.
  458. INFO1651:  UDP_BROAD 7437 tcpPort:625868800
  459. INFO02D0:  use dev Name br0
  460. INFO1538: tcpConnector() started...
  461. INFO1415: Bind to br0
复制代码

  1. Boot and Recovery Environment for Embedded Devices
  2. Copyright (C) 2015 HackPascal <hackpascal@gmail.com>
  3. Build date 2015-07-19 [git-6be20b6]
  4. Version 1.0 (r647)

  5. DRAM: 128MB
  6. Platform: Qualcomm Atheros QCA9558 rev 0
  7. Board: Atheros AP152 reference board
  8. Clocks: CPU: 720MHz, DDR: 600MHz, AHB: 200MHz, Ref: 40MHz
  9. Flash: Winbond W25Q128 (16MB) on ath79-spi
  10. ag71xx-eth: Using MAC address xx:xx:xx:xx:xx:xx
  11. eth0: Atheros AR8327/AR8328 rev 4

  12. Network started on eth0, inet addr 192.168.1.1, netmask 255.255.255.0

  13. Press any key to interrupt autoboot ... 0

  14. Trying to boot firmware from 0x9f020000 ...
  15. TP-LINK firmware image header detected.
  16.     Image Name:   c7000002
  17.     Data Size:    855048 Bytes
  18.     Load Address: 80002000
  19.     Entry Point:  801c7b50
  20. Uncompressing data (LZMA) ... done.
  21. Flushing cache ... done.

  22. Starting kernel at 0x801c7b50...

  23. Booting QCA955x
  24. [    0.000000] Linux version 2.6.31--LSDK-9.2.0_U6.616 (root@liaozhiming) (gcc version 4.3.3 (GCC) ) #1 Wed Mar 4 16:03:08 CST 2015
  25. [    0.000000] Ram size passed from bootloader =128M
  26. [    0.000000] flash_size passed from bootloader = 16
  27. [    0.000000] CPU revision is: 00019750 (MIPS 74Kc)
  28. [    0.000000] cpu apb ddr apb ath_sys_frequency: cpu 720 ddr 600 ahb 200
  29. [    0.000000] Determined physical RAM map:
  30. [    0.000000]  memory: 08000000 @ 00000000 (usable)
  31. [    0.000000] Zone PFN ranges:
  32. [    0.000000]   Normal   0x00000000 -> 0x00008000
  33. [    0.000000] Movable zone start PFN for each node
  34. [    0.000000] early_node_map[1] active PFN ranges
  35. [    0.000000]     0: 0x00000000 -> 0x00008000
  36. [    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 32512
  37. [    0.000000] Kernel command line: console=ttyS0,115200 root=31:02 rootfstype=squashfs init=/sbin/init mtdparts=ath-nor0:128k(u-boot),1024k(kernel),14848k(rootfs),320k(config),64k(ART) mem=128M
  38. [    0.000000] PID hash table entries: 512 (order: 9, 2048 bytes)
  39. [    0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
  40. [    0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
  41. [    0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
  42. [    0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
  43. [    0.000000] Writing ErrCtl register=00000000
  44. [    0.000000] Readback ErrCtl register=00000000
  45. [    0.000000] Memory: 112924k/131072k available (1843k kernel code, 17980k reserved, 430k data, 120k init, 0k highmem)
  46. [    0.000000] NR_IRQS:128
  47. [    0.000000] plat_time_init: plat time init done
  48. [    0.000000] Calibrating delay loop... 359.42 BogoMIPS (lpj=718848)
  49. [    0.080000] Mount-cache hash table entries: 512
  50. [    0.080000]
  51. [    0.080000] ****************ALLOC***********************
  52. [    0.080000]  Packet mem: 8026a4e0 (0xe00000 bytes)
  53. [    0.080000] ********************************************
  54. [    0.080000]
  55. [    0.080000] NET: Registered protocol family 16
  56. [    0.080000] ath_pcibios_init: bus 0
  57. [    0.080000] ***** Warning PCIe 0 H/W not found !!!
  58. [    0.080000] registering PCI controller with io_map_base unset
  59. [    0.080000] ath_pcibios_init: bus 1
  60. [    0.080000] ***** Warning PCIe 1 H/W not found !!!
  61. [    0.080000] registering PCI controller with io_map_base unset
  62. [    0.080000] ===@@@@@@@@@@@=>use GPIO13 as wifi button control!
  63. [    0.080000] bio: create slab <bio-0> at 0
  64. [    0.080000] NET: Registered protocol family 2
  65. [    0.080000] IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
  66. [    0.080000] TCP established hash table entries: 4096 (order: 3, 32768 bytes)
  67. [    0.084000] TCP bind hash table entries: 4096 (order: 2, 16384 bytes)
  68. [    0.084000] TCP: Hash tables configured (established 4096 bind 4096)
  69. [    0.084000] TCP reno registered
  70. [    0.084000] NET: Registered protocol family 1
  71. [    0.084000] ATH GPIOC major 0
  72. [    0.084000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
  73. [    0.084000] msgmni has been set to 220
  74. [    0.084000] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 254)
  75. [    0.084000] io scheduler noop registered
  76. [    0.084000] io scheduler deadline registered (default)
  77. [    0.084000] Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled
  78. [    0.084000] serial8250.0: ttyS0 at MMIO 0xb8020000 (irq = 19) is a 16550A
  79. [    0.084000] console [ttyS0] enabled
  80. [    0.392000] PPP generic driver version 2.4.2
  81. [    0.396000] NET: Registered protocol family 24
  82. [    0.400000] 5 cmdlinepart partitions found on MTD device ath-nor0
  83. [    0.404000] Creating 5 MTD partitions on "ath-nor0":
  84. [    0.412000] 0x000000000000-0x000000020000 : "u-boot"
  85. [    0.416000] 0x000000020000-0x000000120000 : "kernel"
  86. [    0.420000] 0x000000120000-0x000000fa0000 : "rootfs"
  87. [    0.428000] 0x000000fa0000-0x000000ff0000 : "config"
  88. [    0.432000] 0x000000ff0000-0x000001000000 : "ART"
  89. [    0.436000] ->Oops: flash id 0xef4018 .
  90. [    0.440000] Ooops, why the devices couldn't been initialed?
  91. [    0.448000] TCP cubic registered
  92. [    0.452000] NET: Registered protocol family 10
  93. [    0.456000] NET: Registered protocol family 17
  94. [    0.460000] 802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
  95. [    0.468000] All bugs added by David S. Miller <davem@redhat.com>
  96. [    0.472000] athwdt_init: Registering WDT success
  97. [    0.476000] ath_otp_init: Registering OTP success
  98. [    0.484000] VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
  99. [    0.492000] Freeing unused kernel memory: 120k freed
  100. init started:  BusyBox v1.01 (2014.12.08-06:50+0000) multi-call binary
  101. This Board use 2.6.31
  102. [    1.588000] xt_time: kernel timezone is -0000
  103. [    1.756000] nf_conntrack version 0.5.0 (2048 buckets, 81920 max)
  104. [    1.760000] CONFIG_NF_CT_ACCT is deprecated and will be removed soon. Please use
  105. [    1.768000] nf_conntrack.acct=1 kernel parameter, acct=1 nf_conntrack module option or
  106. [    1.776000] sysctl net.netfilter.nf_conntrack_acct=1 to enable it.
  107. [    2.132000] ip_tables: (C) 2000-2006 Netfilter Core Team
  108. insmod: cannot open module `/lib/modules/2.6.31/kernel/iptable_raw.ko': No such file or directory
  109. insmod: cannot open module `/lib/modules/2.6.31/kernel/igmp_agent.ko': No such file or directory
  110. insmod: cannot open module `/lib/modules/2.6.31/kernel/flashid.ko': No such file or directory
  111. [    2.404000] PPPoL2TP kernel driver, V1.0
  112. [    2.420000] PPTP driver version 0.8.3
  113. insmod: cannot open module `/lib/modules/2.6.31/kernel/harmony.ko': No such file or directory

  114. (none) mips #1 Wed Mar 4 16:03:08 CST 2015 (none)
  115. (none) login: [    6.120000] Read from 0X20000 to 0X20120: OK
  116. [    6.208000] Read from 0XFA0000 to 0XFB1CA8: OK
  117. [    6.240000] Read from 0X1FC00 to 0X1FC06: OK
  118. [    6.408000] Read from 0X1FE00 to 0X1FE08: OK
  119. [    6.412000] Erase from 0XFA0000 to 0XFB1CA8:.
  120. [    6.660000] Program from 0XFA0000 to 0XFB1CA8:.
  121. [    7.108000] write successfully
  122. [    7.112000] Read from 0X1FE00 to 0X1FE08: OK
  123. [    7.116000] Erase from 0XFA0000 to 0XFB1CA8:.
  124. [    7.376000] Program from 0XFA0000 to 0XFB1CA8:.
  125. [    7.840000] write successfully
  126. [    7.844000] Erase from 0XFA0000 to 0XFB1CA8:.
  127. [    8.100000] Program from 0XFA0000 to 0XFB1CA8:.
  128. [    8.540000] write successfully
  129. [ucVlanCfg_init,   92]Prepare paramter:vlanEntry_0=0x00000000

  130.                                                              [ucVlanCfg_init,   92]Prepare paramter:vlanEntry_1=0x00000000

  131.                                           [ucVlanCfg_init,   92]Prepare paramter:vlanEntry_2=0x00000000

  132.                        [ucVlanCfg_init,   92]Prepare paramter:vlanEntry_3=0x00000000

  133.     [ucVlanCfg_init,   95]VLAN CFG PARAM STR:vlanEnable=0 vlanEntry_0=0 vlanEntry_1=0 vlanEntry_2=0 vlanEntry_3=0

  134.                                   [    8.936000] qca955x_GMAC: Length per segment 1536
  135. [    8.944000] 955x_GMAC: qca955x_gmac_attach
  136. [    8.948000] 955x_GMAC: qca955x_set_gmac_caps
  137. [    8.952000] Currently in polling mode unit1
  138. [    8.956000] mac:1 Registering S17....
  139. [    8.960000] qca955x_GMAC: RX TASKLET - Pkts per Intr:200
  140. [    8.964000] qca955x_GMAC: Max segments per packet :   1
  141. [    8.972000] qca955x_GMAC: Max tx descriptor count :   220
  142. [    8.976000] qca955x_GMAC: Max rx descriptor count :   220
  143. [    8.980000] qca955x_GMAC: Mac capability flags    :   12002200
  144. [    8.988000] 955x_GMAC: qca955x_gmac_attach
  145. [    8.992000] 955x_GMAC: qca955x_set_gmac_caps
  146. [    8.996000] Currently in polling mode unit0
  147. [    9.000000] mac:0 Registering S17....
  148. [    9.004000] qca955x_GMAC: RX TASKLET - Pkts per Intr:200
  149. [    9.008000] qca955x_GMAC: Max segments per packet :   1
  150. [    9.016000] qca955x_GMAC: Max tx descriptor count :   220
  151. [    9.020000] qca955x_GMAC: Max rx descriptor count :   220
  152. [    9.024000] qca955x_GMAC: Mac capability flags    :   10002A00
  153. [    9.032000] 955x_GMAC: Serdes PLL is locked value 0x1f038116
  154. [    9.644000] athr_gmac_ring_alloc Allocated 3520 at 0x8794f000
  155. [    9.652000] athr_gmac_ring_alloc Allocated 3520 at 0x87aa1000
  156. [    9.956000] 955x_GMAC: eth1 in SGMII MODE
  157. [    9.960000] Scorpion -----> S17 PHY
  158. [    9.992000] Hello, nat helper module for 1.08!
  159. [    9.996000] netlink_kernel_create succeeded at tp_rule_nl_prot: [29]
  160. [   10.000000]
  161. [   10.000000] ######## S17 SSDK init succeeded! ########
  162. [   10.008000] _athrs17_mac0_intf SGMII done
  163. [   10.016000] [VLAN_CONFIG] vlanEnable:Disable
  164. [   10.020000] [VLAN_CONFIG] Aborting VLAN CONFIG!
  165. [   10.028000] athrs17_reg_init:done
  166. [   10.032000] 955x_SGMII::athr_gmac_sgmii_setup  Done
  167. [   10.036000] Setting Drop CRC Errors, Pause Frames and Length Error frames
  168. [   10.044000] Setting PHY...
  169. [   11.048000] Phy setup Complete
  170. [   11.052000] ADDRCONF(NETDEV_UP): eth0: link is not ready
  171. [   11.116000] device eth0.1 entered promiscuous mode
  172. [   11.120000] device eth0 entered promiscuous mode
  173. [   11.132000] Read from 0X1FC00 to 0X1FC06: OK
  174. [   11.136000] SET INTF MAC 0:ec-26-ca-f0-0e-c8
  175. [   11.144000] Lan UDP checksum 0 adding rule #3
  176. [   11.148000] ACL is not yet enabled. Enabling...
  177. [   11.156000] SET INTF MAC 1:ec-26-ca-f0-0e-c9
  178. [   11.160000] ttl adding rule #0
  179. [   11.164000] Wan UDP checksum 0 adding rule #2
  180. [   11.232000] br0: port 1(eth0.1) entering forwarding state
  181. [   12.412000] Adding ACL rules #1 - wan to lan, dst ip is lan net
  182. [   12.880000] nf_conntrack_rtsp v0.6.21 loading
  183. [   12.896000] nf_nat_rtsp v0.6.21 loading
  184. [   12.936000] insmod nat_sip over !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
  185. [   13.088000] adf: module license 'Proprietary' taints kernel.
  186. [   13.092000] Disabling lock debugging due to kernel taint
  187. [   13.720000] ath_hal: 0.9.17.1 (AR5416, AR9380, REGOPS_FUNC, WRITE_EEPROM, TX_DATA_SWAP, RX_DATA_SWAP, 11D)
  188. [   13.784000] ath_rate_atheros: Copyright (c) 2001-2005 Atheros Communications, Inc, All Rights Reserved
  189. usrconf_allocate_memory 212 shmget success id:43511 32769
  190.                                                          [   13.876000] ath_dfs: Version 2.0.0
  191. [   13.876000] Copyright (c) 2005-2006 Atheros Communications, Inc. All Rights Reserved
  192. [   14.204000] ath_dev: Copyright (c) 2001-2007 Atheros Communications, Inc, All Rights Reserved
  193. [   14.804000] Read from 0X20000 to 0X20120: OK
  194. [   16.112000] ath_ahb: 10.2-00082-4 (Atheros/multi-bss)
  195. [   16.120000] __ath_attach: Set global_scn[0]
  196. [   16.132000] Enterprise mode: 0x43fc0000
  197. [   16.136000] Restoring Cal data from Flash
  198. [   16.140000] Green-AP : Green-AP : Attached
  199. [   16.140000]
  200. [   16.152000] ath_get_caps[6148] rx chainmask mismatch actual 7 sc_chainmak 0
  201. [   16.160000] ath_get_caps[6123] tx chainmask mismatch actual 7 sc_chainmak 0
  202. [   16.172000] ath_attach_dfs[12558] dfsdomain 1
  203. [   16.196000] SC Callback Registration for wifi0
  204. [   16.200000] wifi0: Atheros ???: mem=0xb8100000, irq=2
  205. [   16.204000] ath_pci: 10.2-00082-4 (Atheros/multi-bss)
  206. [   16.336000] ath_attach_dfs[12558] dfsdomain 1
  207. [   16.396000] VAP device ath0 created
  208. [   16.456000]
  209. [   16.456000]  DES SSID SET=TP-LINK_0EC8
  210. [   16.468000]  ieee80211_ioctl_siwmode: imr.ifm_active=131712, new mode=3, valid=1
  211. [   16.476000] Set freq vap stop send + 86f74000
  212. [   16.480000] Set freq vap stop send -86f74000
  213. [   16.512000] Set wait done --86f74000
  214. [   16.632000] Set freq vap stop send + 86f74000
  215. [   16.636000] Set freq vap stop send -86f74000
  216. [   16.668000] Set wait done --86f74000
  217. [   21.972000]  Scan in progress.. Cancelling it
  218. [   22.592000] athr_gmac_ring_alloc Allocated 3520 at 0x87bcf000
  219. [   22.596000] athr_gmac_ring_alloc Allocated 3520 at 0x87bf9000
  220. [   22.904000] 955x_GMAC: eth0 in RGMII MODE
  221. [   22.908000] Scorpion -----> S17 PHY
  222. [   22.912000] athrs17_reg_init_wan done
  223. [   22.916000] Setting Drop CRC Errors, Pause Frames and Length Error frames
  224. [   22.924000] Setting PHY...
  225. [   22.928000] ADDRCONF(NETDEV_UP): eth1: link is not ready
  226. [   22.948000] device eth1 entered promiscuous mode
  227. [   23.124000]
  228. [   23.124000] Enet:1 port1 up
  229. [   23.128000] 955x_GMAC: enet unit:1 is up...
  230. [   23.132000] eth1  SGMII  1000Mbps  full duplex
  231. [   23.136000] 955x_GMAC: qca955x_soc_gmac_set_mac_duplex
  232. [   23.140000] 955x_GMAC: qca955x_soc_gmac_set_link Done
  233. [   23.144000] 955x_GMAC: done cfg2 0x7215 ifctl 0x0 miictrl
  234. [   23.152000] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
  235. [   24.448000] device ath0 entered promiscuous mode
  236. [   24.452000] br1: port 2(ath0) entering forwarding state
  237. [   24.924000] 955x_GMAC: qca955x_soc_gmac_set_mac_duplex
  238. [   24.928000] 955x_GMAC: qca955x_soc_gmac_set_link Done
  239. [   24.932000] ADDRCONF(NETDEV_CHANGE): eth1: link becomes ready
  240. [   24.940000] br1: port 1(eth1) entering forwarding state
  241. [   25.068000]  ieee80211_ioctl_siwmode: imr.ifm_active=393856, new mode=3, valid=1
  242. [   25.080000]  Scan in progress.. Cancelling it
  243. [   25.144000] br1: port 2(ath0) entering disabled state
  244. [   25.148000]  DEVICE IS DOWN ifname=ath0
  245. [   25.152000]  DEVICE IS DOWN ifname=ath0
  246. [   25.364000] br1: port 2(ath0) entering forwarding state
  247. [   26.620000]  Scan in progress.. Cancelling it
  248. [   26.684000] br1: port 2(ath0) entering disabled state
  249. [   26.712000] br1: starting userspace STP failed, starting kernel STP
  250. [   26.788000] br1: topology change detected, propagating
  251. [   26.792000] br1: port 2(ath0) entering forwarding state
  252. [   29.084000] mlme_create_infra_bss : Overriding HT40 channel with HT20 channel
  253. [   39.340000] fuse init (API version 7.12)
  254. [   39.504000] usbcore: registered new interface driver usbfs
  255. [   39.508000] usbcore: registered new interface driver hub
  256. [   39.516000] usbcore: registered new device driver usb
  257. [   39.540000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
  258. [   39.548000] Port Status 1c000004
  259. [   39.552000] ath-ehci ath-ehci.0: ATH EHCI
  260. [   39.556000] ath-ehci ath-ehci.0: new USB bus registered, assigned bus number 1
  261. [   39.564000] ehci_reset Intialize USB CONTROLLER in host mode: 13
  262. [   39.572000] ehci_reset Port Status 1c000000
  263. [   39.576000] ath-ehci ath-ehci.0: irq 3, io mem 0x1b000000
  264. [   39.580000] ehci_reset Intialize USB CONTROLLER in host mode: 13
  265. [   39.588000] ehci_reset Port Status 1c000000
  266. [   39.604000] ath-ehci ath-ehci.0: USB 2.0 started, EHCI 1.00
  267. [   39.608000] usb usb1: configuration #1 chosen from 1 choice
  268. [   39.612000] hub 1-0:1.0: USB hub found
  269. [   39.616000] hub 1-0:1.0: 1 port detected
  270. [   39.624000] Port Status 1c000000
  271. [   39.624000] ath-ehci1 ath-ehci1.1: ATH EHCI
  272. [   39.628000] ath-ehci1 ath-ehci1.1: new USB bus registered, assigned bus number 2
  273. [   39.640000] ehci_reset Intialize USB CONTROLLER in host mode: 13
  274. [   39.644000] ehci_reset Port Status 1c000000
  275. [   39.648000] ath-ehci1 ath-ehci1.1: irq 3, io mem 0x1b400000
  276. [   39.656000] ehci_reset Intialize USB CONTROLLER in host mode: 13
  277. [   39.664000] ehci_reset Port Status 1c000000
  278. [   39.680000] ath-ehci1 ath-ehci1.1: USB 2.0 started, EHCI 1.00
  279. [   39.684000] usb usb2: configuration #1 chosen from 1 choice
  280. [   39.692000] hub 2-0:1.0: USB hub found
  281. [   39.692000] hub 2-0:1.0: 1 port detected
  282. [   39.872000] SCSI subsystem initialized
  283. [   40.116000] Initializing USB Mass Storage driver...
  284. [   40.120000] usbcore: registered new interface driver usb-storage
  285. [   40.124000] USB Mass Storage support registered.
  286. [   40.184000]  GPL NetUSB up!
  287. [   40.372000] kc   86 : run_telnetDBGDServer start
  288. [   40.376000] kc  223 : init_DebugD end
  289. [   40.380000] INFO1758: NetUSB 1.184, 0002061F : May  7 2012 10:35:23
  290. [   40.388000] INFO175A:  AUTH ISOC
  291. [   40.392000] INFO175B:
  292. [   40.392000] usbcore: registered new interface driver KC NetUSB General Driver
  293. [   40.400000] INFO0076:  init proc : PAGE_SIZE 4096
  294. [   40.408000] INFO17B4: Check mac address
  295. [   40.412000] INFO162C:  infomap 86ecc220
  296. [   40.416000] INFO162F:  sleep to wait br0 to wake up
  297. [   40.420000] INFO02D0:  use dev Name br0
  298. [   40.424000] INFO1638:  sleep to wait br0 end.
  299. [   40.428000] INFO1651:  UDP_BROAD 7437 tcpPort:625868800
  300. [   40.432000] INFO02D0:  use dev Name br0
  301. [   40.440000] INFO1538: tcpConnector() started...
  302. [   40.784000] IPv6 over IPv4 tunneling driver
  303. [   43.464000] INFO1415: Bind to br0
  304. check success
复制代码

点评

撸主也是7500V3~~~  详情 回复 发表于 2015-7-31 15:29
不要发这么多,我不想看,我知道这个问题,我没有这种路由,暂时没法解决!!!!!!!  详情 回复 发表于 2015-7-28 08:31
我的恩山、我的无线 The best wifi forum is right here.
回复

使用道具 举报

发表于 2015-7-28 02:37 | 显示全部楼层
LZ又更新了......
我的恩山、我的无线 The best wifi forum is right here.
回复

使用道具 举报

发表于 2015-7-28 06:15 | 显示全部楼层
求支持c301
我的恩山、我的无线 The best wifi forum is right here.
回复

使用道具 举报

发表于 2015-7-28 07:23 | 显示全部楼层
2015-07-28 r679]
添加 WNDR4300 支持
增加固件备份的稳定性
增加 wget 命令连接的可靠性
我的恩山、我的无线 The best wifi forum is right here.
回复

使用道具 举报

发表于 2015-7-28 07:31 | 显示全部楼层
本帖最后由 joe1203a 于 2015-7-28 07:38 编辑

楼主你好

在WDR7500 v3 下

官方uboot + 官方固件 (wdr7500 v3 20150423 或Archer C7 v2 150304) = 2.4G 及 5G正常
breed r647 + 官方固件 (wdr7500 v3 20150423 或Archer C7 v2 150304 或 openwrt) = 只有2.4G能用

官方uboot +  官方固件 (wdr7500 v3 20150423) TTL输出
http://pastebin.com/eVi4Y2ri

breed r647 + 官方固件 (Archer C7 v2 150304) TTL输出
http://pastebin.com/zn2Wbbkw

点评

然并卵。我很早就知道了。这些信息无用  发表于 2015-7-29 16:58
我的恩山、我的无线 The best wifi forum is right here.
回复

使用道具 举报

 楼主| 发表于 2015-7-28 08:31 | 显示全部楼层
joe1203a 发表于 2015-7-27 23:47
楼主你好
在wdr7500 v3,
uboot + wdr7500 v3  (20150423) 或 Archer C7 (150304) = 2.4G及5G也能用

不要发这么多,我不想看,我知道这个问题,我没有这种路由,暂时没法解决!!!!!!!
我的恩山、我的无线 The best wifi forum is right here.
回复

使用道具 举报

发表于 2015-7-28 09:33 | 显示全部楼层
又再更新了...太強大..
我的恩山、我的无线 The best wifi forum is right here.
回复

使用道具 举报

您需要登录后才可以回帖 登录 | 立即注册

本版积分规则

有疑问请添加管理员QQ86788181|手机版|小黑屋|Archiver|恩山无线论坛(常州市恩山计算机开发有限公司版权所有) ( 苏ICP备05084872号 )

GMT+8, 2024-3-29 16:52

Powered by Discuz! X3.5

© 2001-2024 Discuz! Team.

| 江苏省互联网有害信息举报中心 举报信箱:js12377 | @jischina.com.cn 举报电话:025-88802724 本站不良内容举报信箱:68610888@qq.com 举报电话:0519-86695797

快速回复 返回顶部 返回列表