(停更)发布斐讯K1 K2 OpenWrt固件，使用OpenWrt开源驱动

wuka*** · 发表于 2016-1-13 09:23

本帖最后由 wukaisky 于 2019-1-6 14:20 编辑

停止更新

自编译的OpenWrt chaos_calmer 斐讯智能路由K1 K1S(PSG1208)、K2(PSG1218)固件

这个补丁提供给想自己编译CC版OpenWrt 斐讯K1固件的网友

我的斐讯K1硬件版本为A1，K2硬件版本为A1和A2
K1S硬件版本为B1

注意：本固件仅作为学习OpenWrt操作用途，无线性能很差，如对无线要求高，请使用潘多拉版固件。
OpenWrt用的开源无线，偶尔无线会挂掉
这个解决不了，MTK闭源驱动移植咱业余的搞不定
所以玩OpenWrt还得用创锐讯Atheros芯片

功能有（标准版）: KMS服务器（mchome），文件传输（maz-1），石像鬼QoS（luci界面蝈蝈，QoS模块官方1.9），SQM QoS，MWAN3 多拨（蝈蝈，感谢xmoon的帮助，修复了/usr/sbin/ip的问题），集成kmod-ipt-nat6
busybox 支持adduser deluser addgroup delgroup

集成两个主题：默认Material，附加darkmatter主题。

石像鬼QoS和MWAN3多拨不能同时用！石像鬼QoS和MWAN3多拨不能同时用！石像鬼QoS和MWAN3多拨不能同时用！
重要的事情说三遍

WPS灯我把它当SYSTEM灯用了，2.4G灯正常。

斐讯K2我自己也撸了个K2 A2版，发现以前的LED灯设置错了，现在的正确的，启动后没有红灯了。
已开启外置PA功能（DTS文件设置）
无线路由器有外置PA信号明显强很多，网速很烂（原因不明）
2.4G信号强度改为0dB，网速会有改善（2.4G很垃圾）
不过5G频段用着很开心；高强度下载，路由器会崩溃。

我请教了蝈蝈，蝈蝈表示如果烧外置PA功放的话，开机一会功夫就烧了，然后信号就几乎没有了
我现在刷外置PA版，一直开着K2，如果真烧了功放，到时会发公告悼念

下面这幅DTS图显示PSG1218开启了外置PA功能

下载地址：
OneDrive网盘

推荐使用免费开源跨平台的FTP客户端：FileZilla
浏览器如果有乱码，可以试试Google Chrome浏览器。

服务器24小时在线，停电、线路及设备维护除外。

位置在 chaos_calmer / ramips / Phicomm_PSG1208(K1_K1S)目录下

PSG1208及PSG1218各版本固件说明：

micro 超级精简版
除了官方默认组件，dnsmasq换成了dnsmasq-full wpad-mini换成了wpad
额外添加了libstdcpp kmod-ipt-nat-extra kmod-nf-nathelper-extra kmod-nls-utf8 kmod-ipt-nat6 ipset relayd tc xl2tpd 6in4 6rd 6to4 aiccu ds-lite iputils-traceroute6 zlib iptables-mod-filter iptables-mod-imq iptables-mod-nat-extra iptables-mod-tproxy
文件传输多拨 MWAN3 UPnP SQM_QoS 石像鬼QoS

mini 精简版
在超级精简版的基础上，额外添加了nano libopenssl wget DDNS

standard 标准版
在精简版的基础上，额外添加 KMS服务器网络唤醒中继桥

16M
在标准版的基础上，额外添加了vim 统计 bind-host curl

AIRS*** · 发表于 2016-1-13 09:40

帮顶待完善

wuka*** · 发表于 2016-1-13 10:08

本帖最后由 wukaisky 于 2016-9-9 20:43 编辑

斐讯PSG1208
Reset： GPIO 1
wifi 2.4G： GPIO 72
wifi 5G： GPIO 24
wps： GPIO 39

贴一下DTS文件：

/dts-v1/;
/include/ "mt7620a.dtsi"
/ {
compatible = "PSG1208", "ralink,mt7620a-soc";
model = "Phicomm PSG1208";
palmbus@10000000 {
gpio0: gpio@600 {
status = "okay";
};
gpio1: gpio@638 {
status = "okay";
};
gpio3: gpio@688 {
status = "okay";
};
spi@b00 {
status = "okay";
m25p80@0 {
#address-cells = <1>;
#size-cells = <1>;
compatible = "w25q64";
reg = <0 0>;
linux,modalias = "m25p80", "w25q64";
spi-max-frequency = <10000000>;
partition@0 {
label = "u-boot";
reg = <0x0 0x30000>;
};
partition@30000 {
label = "u-boot-env";
reg = <0x30000 0x10000>;
read-only;
};
factory: partition@40000 {
label = "factory";
reg = <0x40000 0x10000>;
read-only;
};
partition@50000 {
label = "firmware";
reg = <0x50000 0x7b0000>;
};
};
};
};
ethernet@10100000 {
pinctrl-names = "default";
pinctrl-0 = <&ephy_pins>;
mtd-mac-address = <&factory 0x28>;
ralink,port-map = "llllw";
};
wmac@10180000 {
ralink,mtd-eeprom = <&factory 0>;
};
pcie@10140000 {
status = "okay";
pcie-bridge {
mt76@0,0 {
reg = <0x0000 0 0 0 0>;
device_type = "pci";
mediatek,mtd-eeprom = <&factory 0x8000>;
mediatek,2ghz = <0>;
};
};
};
pinctrl {
state_default: pinctrl0 {
gpio {
ralink,group = "i2c", "spi refclk", "wled";
ralink,function = "gpio";
};
};
};
gpio-leds {
compatible = "gpio-leds";
wps {
label = "phicomm:white:wps";
gpios = <&gpio1 15 1>;
};
wlan {
label = "phicomm:white:wlan2g";
gpios = <&gpio3 0 1>;
};
};
gpio-keys-polled {
compatible = "gpio-keys-polled";
#address-cells = <1>;
#size-cells = <0>;
poll-interval = <20>;
reset {
label = "reset";
gpios = <&gpio0 1 1>;
linux,code = <0x198>;
};
};
};

复制代码

/dts-v1/;
/include/ "mt7620a.dtsi"
/ {
compatible = "PSG1218", "ralink,mt7620a-soc";
model = "Phicomm PSG1218";
palmbus@10000000 {
gpio0: gpio@600 {
status = "okay";
};
spi@b00 {
status = "okay";
m25p80@0 {
#address-cells = <1>;
#size-cells = <1>;
compatible = "gd25q64";
reg = <0 0>;
linux,modalias = "m25p80", "gd25q64";
spi-max-frequency = <10000000>;
partition@0 {
label = "u-boot";
reg = <0x0 0x30000>;
};
partition@30000 {
label = "u-boot-env";
reg = <0x30000 0x10000>;
read-only;
};
factory: partition@40000 {
label = "factory";
reg = <0x40000 0x10000>;
read-only;
};
partition@50000 {
label = "firmware";
reg = <0x50000 0x7b0000>;
};
};
};
};
ethernet@10100000 {
pinctrl-names = "default";
pinctrl-0 = <&ephy_pins>;
mtd-mac-address = <&factory 0x28>;
ralink,port-map = "llllw";
};
wmac@10180000 {
ralink,mtd-eeprom = <&factory 0>;
};
pcie@10140000 {
status = "okay";
pcie-bridge {
mt76@0,0 {
reg = <0x0000 0 0 0 0>;
device_type = "pci";
mediatek,mtd-eeprom = <&factory 0x8000>;
mediatek,2ghz = <0>;
};
};
};
pinctrl {
state_default: pinctrl0 {
gpio {
ralink,group = "i2c", "uartf";
ralink,function = "gpio";
};
pa {
ralink,group = "pa";
ralink,function = "pa";
};
};
};
gpio-leds {
compatible = "gpio-leds";
red {
label = "phicomm:red:status";
gpios = <&gpio0 8 0>;
};
blue {
label = "phicomm:blue:status";
gpios = <&gpio0 10 1>;
};
yellow {
label = "phicomm:yellow:status";
gpios = <&gpio0 11 1>;
};
};
gpio-keys-polled {
compatible = "gpio-keys-polled";
#address-cells = <1>;
#size-cells = <0>;
poll-interval = <20>;
reset {
label = "reset";
gpios = <&gpio0 1 1>;
linux,code = <0x198>;
};
};
};

复制代码

wuka*** · 发表于 2016-1-13 10:10

本帖最后由 wukaisky 于 2016-5-21 10:24 编辑

02_network文件

#!/bin/sh
. /lib/functions.sh
. /lib/ramips.sh
. /lib/functions/uci-defaults-new.sh
. /lib/functions/system.sh
ramips_setup_rt3x5x_vlans()
{
if [ ! -x /sbin/swconfig ]; then
# legacy default
ucidef_set_interfaces_lan_wan "eth0.1" "eth0.2"
return
fi
local wanports=""
local lanports=""
for port in 5 4 3 2 1 0; do
if [ `swconfig dev rt305x port $port get disable` = "1" ]; then
continue
fi
if [ `swconfig dev rt305x port $port get lan` = "0" ]; then
wanports="$port $wanports"
else
lanports="$port $lanports"
fi
done
ucidef_set_interfaces_lan_wan "eth0.1" "eth0.2"
ucidef_add_switch "rt305x" "1" "1"
ucidef_add_switch_vlan "rt305x" "1" "$lanports 6t"
ucidef_add_switch_vlan "rt305x" "2" "$wanports 6t"
}
ramips_setup_interfaces()
{
local board="$1"
ucidef_set_interface_loopback
case $board in
a5-v11)
ucidef_set_interface_lan "eth0.1"
ucidef_add_switch "switch0" "1" "1"
ucidef_add_switch_vlan "switch0" "1" "0 6t"
;;
3g150b | \
3g300m | \
linkits7688 | \
linkits7688d | \
microwrt | \
w150m | \
zte-q7 | \
all0256n | \
all5002 | \
all5003 | \
broadway | \
dcs-930| \
dcs-930l-b1| \
ht-tm02| \
ncs601w | \
wnce2001)
ucidef_add_switch "switch0" "1" "0"
ucidef_set_interface_lan "eth0"
;;
3g-6200nl | \
mlw221 | \
mr-102n)
ucidef_set_interface_lan "eth0.2"
;;
mlwg2)
ucidef_set_interface_lan "eth0.1"
;;
m2m)
ucidef_add_switch "switch0" "4"
ucidef_set_interface_lan "eth0"
;;
wizard8800 | \
wl-330n | \
wmr300)
ucidef_set_interface_lan "eth0.1"
;;
b2c | \
nw718 | \
psr-680w | \
sl-r7205 | \
w502u | \
wr6202)
ucidef_set_interfaces_lan_wan "eth0.1" "eth0.2"
;;
awapn2403)
ucidef_set_interfaces_lan_wan "eth0.1" "eth0.2"
ucidef_add_switch "switch0" "1" "1"
ucidef_add_switch_vlan "switch0" "1" "0 6t"
ucidef_add_switch_vlan "switch0" "2" "1 6t"
;;
br-6475nd)
ucidef_set_interfaces_lan_wan "eth0.1" "eth0.2"
ucidef_add_switch "switch0" "1" "1"
ucidef_add_switch_vlan "switch0" "1" "1 2 3 4 9t"
ucidef_add_switch_vlan "switch0" "2" "0 9t"
;;
re6500 | \
asl26555)
ucidef_set_interface_lan "eth0.1"
ucidef_add_switch "switch0" "1" "1"
ucidef_add_switch_vlan "switch0" "1" "1 2 3 4 6t"
;;
cf-wr800n|\
ex2700)
ucidef_set_interface_lan "eth0.1"
ucidef_add_switch "switch0" "1" "1"
ucidef_add_switch_vlan "switch0" "1" "4 6t"
;;
cy-swr1100)
ucidef_set_interfaces_lan_wan "eth0.1" "eth0.2"
ucidef_add_switch "switch0" "1" "1"
ucidef_add_switch_vlan "switch0" "1" "0 1 2 3 9t"
ucidef_add_switch_vlan "switch0" "2" "4 9t"
;;
3g-6200n | \
ai-br100 | \
dir-610-a1 | \
dir-300-b7 | \
dir-320-b1 | \
dir-615-h1 | \
firewrt | \
pbr-m1 | \
hlk-rm04 | \
mt7621 | \
mt7628 | \
mzk-w300nh2 | \
mzk-750dhp | \
whr-300hp2 | \
whr-600d | \
wsr-600 | \
wsr-1166 | \
wt1520 | \
xiaomi-miwifi-mini |\
y1|\
youku-yk1|\
psg1208 |\
psg1208-16m |\
psg1218 |\
psg1218-16m |\
zbt-wg2626)
ucidef_set_interfaces_lan_wan "eth0.1" "eth0.2"
ucidef_add_switch "switch0" "1" "1"
ucidef_add_switch_vlan "switch0" "1" "0 1 2 3 6t"
ucidef_add_switch_vlan "switch0" "2" "4 6t"
;;
hc5*61)
ucidef_set_interfaces_lan_wan "eth0.1" "eth0.2"
ucidef_add_switch "switch0" "1" "1"
ucidef_add_switch_vlan "switch0" "1" "1 2 3 4 6t"
ucidef_add_switch_vlan "switch0" "2" "0 6t"
;;
whr-1166d)
ucidef_set_interfaces_lan_wan "eth0.1" "eth0.2"
ucidef_add_switch "switch0" "1" "1"
ucidef_add_switch_vlan "switch0" "1" "0 1 2 3 6t"
ucidef_add_switch_vlan "switch0" "2" "5 6t"
;;
wizfi630a)
ucidef_set_interfaces_lan_wan "eth0.1" "eth0.2"
ucidef_add_switch "switch0" "1" "1"
ucidef_add_switch_vlan "switch0" "1" "1 2 6t"
ucidef_add_switch_vlan "switch0" "2" "0 6t"
;;
awm002-evb | \
awm003-evb | \
argus-atp52b | \
dir-645 | \
dir-860l-b1 | \
f5d8235-v1 | \
f5d8235-v2 | \
hg255d | \
rt-n14u | \
wrtnode | \
wt3020 | \
ur-326n4g | \
zbt-wa05)
ucidef_set_interfaces_lan_wan "eth0.1" "eth0.2"
ucidef_add_switch "switch0" "1" "1"
ucidef_add_switch_vlan "switch0" "1" "1 2 3 4 6t"
ucidef_add_switch_vlan "switch0" "2" "0 6t"
;;
ur-336un)
ucidef_set_interfaces_lan_wan "eth0.1" "eth0.2"
;;
br6524n | \
v11st-fe)
ucidef_set_interfaces_lan_wan "eth0.1" "eth0.2"
ucidef_add_switch "switch0" "1" "1"
ucidef_add_switch_vlan "switch0" "1" "1 2 3 4 5t"
ucidef_add_switch_vlan "switch0" "2" "0 5t"
;;
ar670w | \
ar725w | \
rt-n15 | \
wl-351)
ucidef_set_interfaces_lan_wan "eth0.1" "eth0.2"
ucidef_add_switch "switch0" "1" "1"
ucidef_add_switch_vlan "switch0" "1" "0 1 2 3 5t"
ucidef_add_switch_vlan "switch0" "2" "4 5t"
;;
rt-n56u)
ucidef_set_interfaces_lan_wan "eth0.1" "eth0.2"
ucidef_add_switch "switch0" "1" "1"
ucidef_add_switch_vlan "switch0" "1" "0 1 2 3 8t"
ucidef_add_switch_vlan "switch0" "2" "4 8t"
;;
tew-691gr|\
tew-692gr)
ucidef_set_interfaces_lan_wan "eth0.1" "eth0.2"
ucidef_add_switch "switch0" "1" "1"
ucidef_add_switch_vlan "switch0" "1" "0t 1 2 3 4"
ucidef_add_switch_vlan "switch0" "2" "0t 5"
;;
vocore)
ucidef_set_interface_lan "eth0.1"
ucidef_add_switch "switch0" "1" "1"
ucidef_add_switch_vlan "switch0" "1" "0 4 6t"
;;
wcr-150gn)
ucidef_set_interfaces_lan_wan "eth0.1" "eth0.2"
ucidef_add_switch "switch0" "1" "1"
ucidef_add_switch_vlan "switch0" "1" "0 6t"
ucidef_add_switch_vlan "switch0" "2" "6t"
;;
wr8305rt)
ucidef_set_interfaces_lan_wan "eth0.1" "eth0.2"
ucidef_add_switch "switch0" "1" "1"
ucidef_add_switch_vlan "switch0" "1" "0 1 2 3 4 6t"
ucidef_add_switch_vlan "switch0" "2" "4 6t"
;;
y1s)
ucidef_set_interfaces_lan_wan "eth0.1" "eth0.2"
ucidef_add_switch "switch0" "1" "1"
ucidef_add_switch_vlan "switch0" "1" "1 2 3 4 5 6t"
ucidef_add_switch_vlan "switch0" "2" "0 6t"
;;
d105 | \
na930 | \
omni-emb-hpm|\
wli-tx4-ag300n)
ucidef_set_interface_lan "eth0"
;;
e1700 | \
mt7620a_mt7530)
ucidef_set_interfaces_lan_wan "eth0.1" "eth0.2"
ucidef_add_switch "switch1" "1" "1"
ucidef_add_switch_vlan "switch1" "1" "0 1 2 3 6t"
ucidef_add_switch_vlan "switch1" "2" "4 6t"
;;
wzr-agl300nh)
ucidef_set_interfaces_lan_wan "eth0.1" "eth0.2"
ucidef_add_switch "switch0" "1" "1"
ucidef_add_switch_vlan "switch0" "1" "1 2 3 4 5t"
ucidef_add_switch_vlan "switch0" "2" "0 5t"
;;
*)
RT3X5X=`cat /proc/cpuinfo | egrep "(RT3.5|RT5350)"`
if [ -n "${RT3X5X}" ]; then
ramips_setup_rt3x5x_vlans
else
ucidef_set_interfaces_lan_wan "eth0.1" "eth0.2"
fi
;;
esac
}
ramips_setup_macs()
{
local board="$1"
local lan_mac=""
local wan_mac=""
case $board in
br-6475nd)
lan_mac=$(cat /sys/class/net/eth0/address)
wan_mac=$(mtd_get_mac_binary devdata 7)
;;
w306r-v20)
lan_mac=$(cat /sys/class/net/eth0/address)
wan_mac=$(macaddr_add "$lan_mac" 5)
;;
tew-691gr)
lan_mac=$(cat /sys/class/net/eth0/address)
wan_mac=$(macaddr_add "$lan_mac" 3)
;;
tew-692gr)
lan_mac=$(cat /sys/class/net/eth0/address)
wan_mac=$(macaddr_add "$lan_mac" 4)
;;
m3 |\
m4 |\
x5 |\
x8)
lan_mac=$(cat /sys/class/net/eth0/address)
lan_mac=$(macaddr_add "$lan_mac" -2)
;;
a5-v11 |\
bc2 |\
broadway |\
d105 |\
dir-620-a1 |\
esr-9753 |\
freestation5 |\
hlk-rm04 | \
mpr-a1 | \
mpr-a2 | \
dir-300-b7 | \
dir-320-b1 | \
psr-680w |\
sl-r7205 |\
y1 |\
y1s)
lan_mac=$(cat /sys/class/net/eth0/address)
lan_mac=$(macaddr_setbit_la "$lan_mac")
wan_mac=$(macaddr_add "$lan_mac" 1)
;;
ht-tm02)
lan_mac=$(cat /sys/class/net/eth0/address)
;;
cy-swr1100 | \
dir-645)
lan_mac=$(mtd_get_mac_ascii nvram lanmac)
wan_mac=$(mtd_get_mac_ascii nvram wanmac)
;;
e1700)
wan_mac=$(mtd_get_mac_ascii config WAN_MAC_ADDR)
;;
wcr-150gn)
wan_mac=$(mtd_get_mac_binary factory 40)
;;
hc5*61)
lan_mac=`mtd_get_mac_ascii bdinfo "Vfac_mac "`
[ -n "$lan_mac" ] || lan_mac=$(cat /sys/class/net/eth0/address)
wan_mac=$(macaddr_add "$lan_mac" 1)
;;
youku-yk1)
lan_mac=$(mtd_get_mac_binary factory 4)
wan_mac=$(macaddr_add "$lan_mac" 1)
;;
psg1208 | \
psg1208-16m | \
psg1218 | \
psg1218-16m)
lan_mac=$(mtd_get_mac_binary factory 40)
wan_mac=$(mtd_get_mac_binary factory 46)
;;
rt-n56u)
lan_mac=$(cat /sys/class/net/eth0/address)
lan_mac=$(macaddr_setbit_la "$lan_mac")
wan_mac=$(mtd_get_mac_binary factory 32772)
;;
all0239-3g | \
carambola | \
freestation5 | \
w502u | \
wnce2001)
wan_mac=$(mtd_get_mac_binary factory 46)
;;
wsr-600|whr-300hp2|whr-600d|whr-1166d)
wan_mac=$(mtd_get_mac_binary factory 4)
lan_mac=$wan_mac
;;
wizfi630a)
lan_mac=$(mtd_get_mac_binary factory 4)
wan_mac=$(mtd_get_mac_binary factory 40)
;;
wsr-1166)
local index="$(find_mtd_index "board_data")"
wan_mac="$(grep -m1 mac= "/dev/mtd${index}" | cut -d= -f2)"
lan_mac=$wan_mac
;;
linkits7688 | \
linkits7688d)
wan_mac=$(mtd_get_mac_binary factory 4)
lan_mac=$(mtd_get_mac_binary factory 46)
;;
*)
lan_mac=$(cat /sys/class/net/eth0/address)
wan_mac=$(macaddr_add "$lan_mac" 1)
;;
esac
[ -n "$lan_mac" ] && ucidef_set_interface_macaddr lan $lan_mac
[ -n "$wan_mac" ] && ucidef_set_interface_macaddr wan $wan_mac
}
board_config_update
board=$(ramips_board_name)
ramips_setup_interfaces $board
ramips_setup_macs $board
board_config_flush
exit 0

复制代码

muzi*** · 发表于 2016-1-13 10:17

WIFI驱动呢， MTK闭源的还是OP开源的？

wuka*** · 发表于 2016-1-13 10:22

本帖最后由 wukaisky 于 2016-5-22 22:22 编辑

01_leds

#!/bin/sh
. /lib/functions/uci-defaults-new.sh
. /lib/ramips.sh
set_usb_led() {
ucidef_set_led_usbdev "usb" "USB" "$1" "1-1"
}
开源驱动
set_wifi_led() {
ucidef_set_led_netdev "wifi_led" "wifi" "$1" "wlan0"
}
board=$(ramips_board_name)
board_config_update
case $board in
3g-6200n)
set_wifi_led "edimax:amber:wlan"
set_usb_led "edimax:blue:3g"
;;
3g-6200nl)
set_wifi_led "edimax:green:wlan"
;;
3g150b |\
3g300m)
set_usb_led "tenda:blue:3g"
;;
ai-br100)
ucidef_set_led_netdev "wan" "wan" "aigale:blue:wan" "eth0.2"
set_wifi_led "aigale:blue:wlan"
;;
a5-v11)
ucidef_set_led_default "power" "POWER" "a5-v11:red:power" "1"
;;
air3gii)
set_wifi_led "airlive:green:wlan"
set_usb_led "airlive:green:mobile"
;;
all0256n)
ucidef_set_rssimon "wlan0" "40000" "1"
ucidef_set_led_rssi "rssilow" "RSSILOW" "all0256n:green:rssilow" "wlan0" "1" "40" "0" "6"
ucidef_set_led_rssi "rssimedium" "RSSIMEDIUM" "all0256n:green:rssimed" "wlan0" "30" "80" "-29" "5"
ucidef_set_led_rssi "rssihigh" "RSSIHIGH" "all0256n:green:rssihigh" "wlan0" "70" "100" "-69" "8"
set_wifi_led "rt2800pci-phy0::radio"
;;
ar670w|\
ar725w|\
awapn2403)
set_wifi_led "rt2800soc-phy0::radio"
;;
asl26555)
ucidef_set_led_default "power" "POWER" "asl26555:green:power" "1"
ucidef_set_led_netdev "eth" "ETH" "asl26555:green:eth" "eth0"
set_wifi_led "asl26555:green:wlan"
set_usb_led "asl26555:green:3g"
;;
bc2)
set_usb_led "bc2:blue:usb"
;;
br6425)
set_wifi_led "edimax:orange:wlan"
;;
br-6475nd)
set_wifi_led "edimax:amber:wlan"
;;
broadway)
set_usb_led "red:diskmounted"
set_wifi_led "red:wps_active"
;;
br6524n)
set_wifi_led "edimax:blue:wlan"
;;
cf-wr800n)
ucidef_set_led_netdev "lan" "lan" "comfast:white:ethernet" eth0.1
set_wifi_led "comfast:white:wifi"
;;
cy-swr1100)
ucidef_set_led_default "wps" "WPS" "samsung:blue:wps" "0"
set_usb_led "samsung:blue:usb"
;;
d105)
ucidef_set_led_default "power" "POWER" "d105:red:power" "1"
set_usb_led "d105:green:usb"
;;
dcs-930l-b1)
ucidef_set_led_default "power" "POWER" "d-link:red:power" "1"
ucidef_set_led_netdev "wifi" "WiFi" "d-link:blue:wps"
;;
dir-300-b1|\
dir-600-b1|\
dir-600-b2|\
dir-620-a1)
# ANDed with vlan switch port 4 led state
ucidef_set_led_default "wan" "WAN LED (amber)" "d-link:amber:wan" "1"
set_wifi_led "rt2800pci-phy0::radio"
;;
dir-615-d|\
dir-615-h1)
ucidef_set_led_default "status" "Status LED (amber)" "d-link:amber:status" "0"
set_wifi_led "rt2800pci-phy0::radio"
;;
dir-620-d1)
set_wifi_led "d-link:green:wifi"
;;
dir-810l)
ucidef_set_led_default "power" "POWER" "d-link:green:power" "1"
;;
dir-610-a1 |\
dir-300-b7 |\
dir-320-b1 |\
esr-9753)
set_wifi_led "rt2800pci-phy0::radio"
;;
ex2700)
ucidef_set_led_default "power_r" "POWER (red)" "ex2700:red:power" "0"
set_wifi_led "ex2700:green:router"
;;
f5d8235-v1)
set_usb_led "f5d8235-v1:blue:storage"
;;
f5d8235-v2)
set_usb_led "f5d8235v2:blue:storage"
;;
fonera20n)
set_usb_led "fonera20n:orange:usb"
set_wifi_led "fonera20n:orange:wifi"
;;
hc5661)
ucidef_set_led_default "system" "system" "hc5661:blue:system" "1"
ucidef_set_led_netdev "internet" "internet" "hc5661:blue:internet" "eth0.2"
set_wifi_led "hc5661:blue:wlan2g"
;;
hc5761)
ucidef_set_led_default "system" "system" "hc5761:blue:system" "1"
ucidef_set_led_netdev "internet" "internet" "hc5761:blue:internet" "eth0.2"
set_wifi_led "hc5761:blue:wlan2g"
ucidef_set_led_netdev "wifi5g" "wifi5g" "hc5761:blue:wlan5g" "rai0"
;;
hc5861)
ucidef_set_led_default "system" "system" "hc5861:blue:system" "1"
ucidef_set_led_netdev "internet" "internet" "hc5861:blue:internet" "eth0.2"
set_wifi_led "hc5861:blue:wlan2g"
ucidef_set_led_netdev "wifi5g" "wifi5g" "hc5861:blue:wlan5g" "rai0"
ucidef_set_led_default "turbo" "turbo" "hc5861:blue:turbo" "0"
;;
hlk-rm04)
set_wifi_led "rt2800pci-phy0::radio"
;;
ht-tm02)
ucidef_set_led_netdev "eth" "Ethernet" "ht-tm02:green:lan" "eth0"
set_wifi_led "ht-tm02:blue:wlan"
;;
all0239-3g|\
hw550-3g)
set_usb_led "hw550-3g:green:usb"
;;
mlw221|\
mlwg2)
set_wifi_led "kingston:blue:wifi"
ucidef_set_led_default "system" "system" "kingston:blue:system" "1"
;;
mofi3500-3gn)
set_usb_led "mofi3500-3gn:green:usb"
;;
mpr-a1)
set_wifi_led "hame:blue:system"
;;
mpr-a2)
set_wifi_led "hame:blue:system"
;;
mr-102n)
set_wifi_led "mr-102n:green:wlan"
set_usb_led "mr-102n:green:usb"
;;
mzk-w300nh2)
set_wifi_led "mzkw300nh2:amber:wlan"
;;
na930)
set_usb_led "na930:blue:status"
;;
nw718)
set_usb_led "nw718:amber:usb"
;;
m2m)
set_wifi_led "m2m:blue:wifi"
ucidef_set_led_netdev "eth" "Ethernet" "m2m:green:wan" "eth0"
;;
omni-emb-hpm)
ucidef_set_led_default "power" "POWER" "emb:orange:power" "1"
ucidef_set_led_netdev "eth" "ETH" "emb:green:eth" "eth0"
set_wifi_led "emb:green:wifi"
;;
omni-plug)
set_wifi_led "miniplug:green:wlan"
set_usb_led "miniplug:green:mobile"
;;
px4885)
set_wifi_led "7links:orange:wifi"
set_usb_led "7links:blue:storage"
;;
pbr-m1)
ucidef_set_led_netdev "internet" "internet" "pbr-m1:green:internet" "eth0.2"
ucidef_set_led_default "power" "power" "pbr-m1:green:power" "1"
ucidef_set_led_default "sys" "sys" "pbr-m1:green:sys" "1"
;;
sl-r7205)
set_wifi_led "rt2800pci-phy0::radio"
;;
v11st-fe)
set_wifi_led "rt2800pci-phy0::radio"
;;
vocore)
ucidef_set_led_netdev "eth" "ETH" "vocore:orange:eth" "eth0"
set_wifi_led "vocore:green:status"
;;
w306r-v20)
set_wifi_led "rt2800pci-phy0::radio"
;;
w502u)
set_usb_led "alfa:blue:usb"
set_wifi_led "rt2800pci-phy0::radio"
;;
wcr-150gn)
set_usb_led "wcr150gn:amber:user"
;;
hg255d)
set_wifi_led "hg255d:wlan"
set_usb_led "hg255d:usb"
ucidef_set_led_interface "lan" "hg255d:internet"
;;
wnce2001)
set_wifi_led "netgear:green:wlan"
;;
re6500)
ucidef_set_led_default "power" "power" "linksys:white:power" "1"
ucidef_set_led_default "wifi" "wifi" "linksys:orange:wifi" "1"
;;
rt-n14u)
ucidef_set_led_default "power" "power" "asus:blue:power" "1"
ucidef_set_led_netdev "lan" "lan" "asus:blue:lan" eth0.1
ucidef_set_led_netdev "wan" "wan" "asus:blue:wan" eth0.2
set_wifi_led "asus:blue:air"
set_usb_led "asus:blue:usb"
;;
rp-n53)
ucidef_set_led_netdev "eth" "Network" "asus:white:back" "eth0"
set_wifi_led "asus:blue:wifi"
;;
whr-300hp2 |\
whr-600d |\
whr-1166d)
ucidef_set_led_default "power" "power" "buffalo:green:power" "1"
ucidef_set_led_default "router" "router" "buffalo:green:router" "1"
;;
zbt-wa05)
ucidef_set_led_default "power" "power" "zbtlink:blue:power" "1"
set_wifi_led "zbtlink:blue:air"
set_usb_led "zbtlink:blue:usb"
;;
wr8305rt)
ucidef_set_led_default "power" "power" "wr8305rt:sys" "1"
set_usb_led "wr8305rt:usb"
set_wifi_led "wr8305rt:wifi"
;;
wt1520)
set_wifi_led "rt2800pci-phy0::radio"
;;
wt3020)
ucidef_set_led_default "power" "power" "nexx:blue:power" "0"
;;
xiaomi-miwifi-mini)
ucidef_set_led_default "power" "power" "xiaomi:blue:status" "1"
;;
y1 |\
y1s)
ucidef_set_led_default "power" "power" "lenovo:blue:power" "1"
set_usb_led "lenovo:blue:usb"
ucidef_set_led_netdev "wifi" "wifi" "lenovo:blue:wifi" "wlan1"
ucidef_set_led_netdev "internet" "internet" "lenovo:blue:internet" "eth0.2"
ucidef_set_led_netdev "lan" "lan" "lenovo:blue:lan" "eth0.1"
ucidef_set_led_netdev "wifi5g" "wifi5g" "lenovo:blue:wifi5g" "wlan0"
;;
zbt-wg2626)
ucidef_set_led_default "power" "power" "zbt-wg2626:green:power" "1"
set_wifi_led "zbt-wg2626:green:air"
set_usb_led "zbt-wg2626:green:usb"
;;
zte-q7)
set_wifi_led "zte:blue:status"
;;
youku-yk1)
ucidef_set_led_default "power" "power" "youku-yk1:blue:power" "1"
set_wifi_led "youku-yk1:blue:air"
set_usb_led "youku-yk1:blue:usb"
ucidef_set_led_netdev "wan" "wan" "youku-yk1:blue:wan" "eth0.2"
;;
psg1208 |\
psg1208-16m)
ucidef_set_led_default "wps" "wps" "phicomm:white:wps" "1"
ucidef_set_led_netdev "wlan" "wlan" "phicomm:white:wlan2g" "wlan1"
;;
psg1218 |\
psg1218-16m)
ucidef_set_led_default "system" "system" "phicomm:blue:status" "1"
;;
esac
board_config_flush
exit 0

复制代码

ha*** · 发表于 2016-1-13 10:27

muziling 发表于 2016-1-13 10:17
WIFI驱动呢， MTK闭源的还是OP开源的？

应该是op的，闭源驱动少人有，而且要大改

wuka*** · 发表于 2016-1-13 10:37

本帖最后由 wukaisky 于 2016-1-13 13:46 编辑

factory分区MAC地址提取方法：

psg1208)
lan_mac=$(mtd_get_mac_binary factory 40)
wan_mac=$(mtd_get_mac_binary factory 46)
;;

复制代码

wzgfe*** · 发表于 2016-1-13 12:39

能多拨么，还是得自己装？

康*** · 发表于 2016-1-13 12:48

顶上去期待完美

wuka*** · 发表于 2016-1-13 13:41

wzgfeixiang 发表于 2016-1-13 12:39
能多拨么，还是得自己装？

满足你的要求。

用蝈蝈（981213）的多拨代码编译了一个，不过没条件测试。

qq743*** · 发表于 2016-1-13 13:50

能做712的吗，712现在的固件没5G驱动貌似

wuka*** · 发表于 2016-1-13 13:51

qq743204199 发表于 2016-1-13 13:50
能做712的吗，712现在的固件没5G驱动貌似

抱歉，我没有这个路由器

lin*** · 发表于 2016-1-13 15:10

帮顶一下，刷了小米的潘多拉，昨天还在想找专门编译的固件，今天就看到了

For*** · 发表于 2016-1-13 15:34

LED灯不亮可能是GPIO不对吧

账号		自动登录	找回密码
密码			立即注册

[k2] (停更)发布斐讯K1 K2 OpenWrt固件，使用OpenWrt开源驱动

本帖子中包含更多资源

点评

评分

相关帖子

本帖子中包含更多资源

点评

本帖子中包含更多资源

点评

点评

点评

点评

点评