现有 B70 极路由 ttl 启动信息发出来。大家一起研究

xiaojuzi · 发表于 2017-2-21 16:04

启动信息如下。原厂固件。

Xshell for Xmanager Enterprise 5 (Build 0544)
Copyright (c) 2002-2015 NetSarang Computer, Inc. All rights reserved.
Type `help' to learn how to use Xshell prompt.
[d:\~]$
Connecting to COM3...
Connected.
procd: - shutdown -
[ 317.000000] ethernet: port4 linkdown(dev event)
[ 320.580000] HWF-Kproxy: Module is ready to exit
[ 320.580000] HWF-Kproxy: Module is removed
[ 320.830000] br-lan: port 3(rai0) entered disabled state
[ 320.830000] br-lan: port 2(ra0) entered disabled state
[ 320.840000] br-lan: port 1(eth2) entered disabled state
[ 320.840000] br-lan: port 1(eth2) entered disabled state
[ 320.850000] device ra0 left promiscuous mode
[ 320.850000] br-lan: port 2(ra0) entered disabled state
[ 320.860000] device rai0 left promiscuous mode
[ 320.860000] br-lan: port 3(rai0) entered disabled state
[ 320.940000] device ra0 entered promiscuous mode
[ 320.940000] device rai0 entered promiscuous mode
[ 320.950000] br-lan: port 3(rai0) entered forwarding state
[ 320.950000] br-lan: port 3(rai0) entered forwarding state
[ 320.960000] br-lan: port 2(ra0) entered forwarding state
[ 320.960000] br-lan: port 2(ra0) entered forwarding state
[ 320.970000] br-lan: port 1(eth2) entered forwarding state
[ 320.970000] br-lan: port 1(eth2) entered forwarding state
[ 320.990000] br-lan1: port 1(eth2.3) entered disabled state
[ 321.000000] device eth2.3 left promiscuous mode
[ 321.000000] br-lan1: port 1(eth2.3) entered disabled state
[ 321.010000] IPv6: ADDRCONF(NETDEV_UP): eth2.3: link is not ready
[ 321.190000] device eth2.3 entered promiscuous mode
[ 321.200000] br-lan1: port 1(eth2.3) entered forwarding state
[ 321.200000] br-lan1: port 1(eth2.3) entered forwarding state
[ 321.380000] br-lan: port 2(ra0) entered disabled state
[ 321.480000] br-lan: port 3(rai0) entered disabled state
[ 322.930000] UBIFS: un-mount UBI device 1, volume 0
[ 322.930000] UBIFS: background thread "ubifs_bgt1_0" stops
procd: - reboot -
[ 322.960000] Stopped WatchDog Timer.
[ 322.960000] nl wifi shutdown rai
[ 322.970000] br-lan: port 1(eth2) entered forwarding state
[ 322.970000] ==>MT7612E Radio Off
[ 323.000000] nl wifi shutdown ra
[ 323.000000] ==>MT7603E Radio Off
[ 323.200000] br-lan1: port 1(eth2.3) entered forwarding state
[ 323.620000] Restarting system.
怘恦tttttttttttttttttttttttttttttttttttttttttttttttttttttttttttttttttt徘无fxx쇦xffᦞ`fx?~x٠旦f怘徘fff䖘fffft ?xxxf恦ttttttttttttttttttttttttttttttttttttttttttttttttttttttttttttttttt從~fxfؘ%UD986兩x柦ff~t臦忠枘f`旦ؘ瞆~?怘恦fffؘ柸xf~~f٠從fؘ杠fxf~f섆tt罹᧦f恦ttff慠ttt``fxttt忦נ`奠ؘ瞆؆t晦xt`x忦֘`奠ؘxƘ؆ t䖞`x`忦֞`奠ؘfxƘ؆tfxt忠朘``瞆~?%UD918xx׾f徆``帘fx`~?膀f緦x量~t杦馀f怘徘?x`x䖞`옘?٠x? 徘徘~?徘??徘x徘x徘徘䗾?徘徘徘~?徘徘~?徘~?徘~?徘`?֞徘~????????֞徘`?????????徘?~?????????徘٠~????徘?徘׸徘?徘٦~?徘?徘֞徘?~?徘ٸ~?徘؆~?徘?~?徘؀~?徘?徘ֆ~?徘?徘fᦞ祸t٦徘fx䆘t`徘~?888888888888恾~tfxݦ~ffx?忠ff 妘`f`f?~f?f恦tttttttttttttttttttttttttttttttttttt ttttttttttttttttttttttttttttt怆ff`fffx咽`xff%UDD86~~f虠f徆t枘恦ttttttttttttttttttttttttttttttttttttttttttttttttttttttttttttttttt徆٦咽`xxff~ffx怘恦ttttttttttttttttttttttttttttttttttttttttttttttttttttttttttttttttt徘f`?xx䖘?恦懦懦懦懦懦懦懦懦懦懦懦懦懦懦懦懦懦懦懦徘?鞘?昘?枘徆?٠鞘x?٠恦懦懦懦懦懦懦懦懦懦懦懦懦懦懦懦懦懦懦懦恦恦tttttttttttttttttttt ttttttttttttttttttttttttttttttttttttttttttttt徘`f綆~ᦞ~f怀ff繦綆綆xff~ffx枆禞ffx兩怆ff``fx~f旸杦f怆彠xff~`fftx`fftx恦tttttt ttttttttttttttttttttttttttttttttttttttttttttttttttttttttttt徘f`f`ff咽``ff徘f~xfx徆fx昆f~x徘fx?x從x٠f~x忠fx?f~x忦fx׸fx忸fxx?x忾fx٦x恦ttttttttttttttttttttttttttttttttttttttttttttttttttttttttttttttttt從`fxff~ffx綆~怘恦ttttttttttttttttttttttttttttttttttttttttttttttttttttttttttttttttt徘f`?xx䖘?恦懦懦懦懦懦懦懦懦懦懦懦懦懦懦懦懦懦懦懦徘٠ ?٠?鶘??٠徆٠׸٠???恦ttttttttttttttttttttttttttttttt tttttttttttttttttttttttttttttttttt恦ttttttttttttttttttttttttttttttttttttttttttttttttttttttttttttttttt徘fffx句~f句徆t枘恦ttttttttttttttttttttttttttttttttttttttttttttttttttttttttttttttttt忠ffttt٦咽妆饦?txxxx忠f繦ffx句~f奸ކ܆綆~tfx綆xކ奦繦솘~f٦x朞ᦞf`f?忠f繦ffx句~f奸ކ܆綆~tfx綆xކ奦繦%UD998~f٦x朞ᦞf`fx忠ffttf٦咽妆饦?txxxx؀x怘忠ffttf?Ƙ咽妆饦?txxxx忠f繦ffx句~f奸ކ܆綆~tfxxކ奦繦%UD998~f?Ęx朞ᦞf`f?忠ffttf׸Ƙ咽妆饦?txxxx忠f繦ffx句~f奸ކ܆綆~tfxxކ奦繦솘~f׸Ęx朞ᦞf`fx徘f~f~`ff`fft徘f~f~`ff`fft徘`f~~?怞ff夘`ff句徆t秦祸`f恦怘恦ttttt ttttttttttttttttttttttttttttttttttttttttttttttttttttttttttttt徘无fxx쇦xffᦞ`fxxt䆘徘fff䖘fffft?xxxf恦tttttttttttttttttttttttttttttttttttttttttttttttttttttttttttttttttt
U-Boot 1.1.3 (Nov 8 2016 - 02:34:36)
Board: Ralink APSoC DRAM: 256 MB
mtest end addr: 8fe79f88
relocate_code Pointer at: 8ff9c000
Config XHCI 40M PLL
******************************
Software System Reset Occurred
******************************
Allocate 16 byte aligned buffer: 8ffe0310
Enable NFI Clock
# MTK NAND # : Use HW ECC
NAND ID [C8 D1 80 95 40]
Device not found, ID: c8d1
Not Support this Device!
chip_mode=00000001
Support this Device in MTK table! c8d1
select_chip
[NAND]select ecc bit:4, sparesize :64 spare_per_sector=16
Signature matched and data read!
load_fact_bbt success 1023
load fact bbt success
[mtk_nand] probe successfully!
mtd->writesize=2048 mtd->oobsize=64, mtd->erasesize=131072 devinfo.iowidth=8
.*** Warning - bad CRC, using default environment
dcache: sets:256, ways:4, linesz:32 ,total:32768
##### The CPU freq = 880 MHZ ####
estimate memory size =256 Mbytes
#Reset_MT7530
set LAN/WAN LLLLW 0
firmware_backup is equal to firmware!
=================================================
Check firmware :
Header Magic Number --> OK
Header Checksum --> OK
Data Checksum --> ......................OK
MD5 Header Magic Number --> OK
MD5 Header CRC --> OK
MD5 Firmware md5 --> ............................................................................................................................................................................................OK
=================================================
firmware: check ok!
3: System Boot system code via Flash.
## Booting image at bc140000 ...
Image Name: HC5962
Image Type: MIPS Linux Kernel Image (lzma compressed)
Data Size: 1438716 Bytes = 1.4 MB
Load Address: 80001000
Entry Point: 80001000
...................... Verifying Checksum ... OK
Uncompressing Kernel Image ... OK
No initrd
## Transferring control to Linux (at address 80001000) ...
## Giving linux memsize in MB, 256
Starting kernel ...
[ 0.000000] Linux version 3.10.49 (build@DEV-9-1-242) (gcc version 4.8.3 (OpenWrt/Linaro GCC 4.8-2014.04 1.2.5.15805s) ) #1 SMP Tue Nov 8 02:53:32 CST 2016
[ 0.000000]
[ 0.000000] The CPU feqenuce set to 880 MHz
[ 0.000000] GCMP present
[ 0.000000] CPU0 revision is: 0001992f (MIPS 1004Kc)
[ 0.000000] Software DMA cache coherency
[ 0.000000] Determined physical RAM map:
[ 0.000000] memory: 10000000 @ 00000000 (usable)
[ 0.000000] Initrd not found or empty - disabling initrd
[ 0.000000] Zone ranges:
[ 0.000000] Normal [mem 0x00000000-0x0fffffff]
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x00000000-0x0fffffff]
[ 0.000000] Detected 3 available secondary CPU(s)
[ 0.000000] Primary instruction cache 32kB, 4-way, VIPT, linesize 32 bytes.
[ 0.000000] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
[ 0.000000] MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
[ 0.000000] PERCPU: Embedded 7 pages/cpu @81203000 s6912 r8192 d13568 u32768
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 65024
[ 0.000000] Kernel command line: board=HC5962 console=ttyS1,115200 rootfstype=squashfs,jffs2
[ 0.000000] PID hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
[ 0.000000] Writing ErrCtl register=0001b087
[ 0.000000] Readback ErrCtl register=0001b087
[ 0.000000] allocated 524288 bytes of page_cgroup
[ 0.000000] please try 'cgroup_disable=memory' option if you don't want memory cgroups
[ 0.000000] Memory: 254808k/262144k available (3208k kernel code, 7336k reserved, 720k data, 224k init, 0k highmem)
[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
[ 0.000000] Hierarchical RCU implementation.
[ 0.000000] NR_IRQS:128
[ 0.000000] console [ttyS1] enabled
[ 0.130000] Calibrating delay loop... 577.53 BogoMIPS (lpj=2887680)
[ 0.190000] pid_max: default: 32768 minimum: 301
[ 0.190000] Mount-cache hash table entries: 512
[ 0.200000] Initializing cgroup subsys memory
[ 0.200000] Initializing cgroup subsys devices
[ 0.200000] Initializing cgroup subsys net_cls
[ 0.210000] Initializing cgroup subsys blkio
[ 0.210000] Initializing cgroup subsys net_prio
[ 0.220000] launch: starting cpu1
[ 0.220000] launch: cpu1 gone!
[ 0.220000] Primary instruction cache 32kB, 4-way, VIPT, linesize 32 bytes.
[ 0.220000] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
[ 0.220000] MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
[ 0.220000] CPU1 revision is: 0001992f (MIPS 1004Kc)
[ 0.280000] Synchronize counters for CPU 1: done.
[ 0.290000] launch: starting cpu2
[ 0.290000] launch: cpu2 gone!
[ 0.290000] Primary instruction cache 32kB, 4-way, VIPT, linesize 32 bytes.
[ 0.290000] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
[ 0.290000] MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
[ 0.290000] CPU2 revision is: 0001992f (MIPS 1004Kc)
[ 0.350000] Synchronize counters for CPU 2: done.
[ 0.360000] launch: starting cpu3
[ 0.360000] launch: cpu3 gone!
[ 0.360000] Primary instruction cache 32kB, 4-way, VIPT, linesize 32 bytes.
[ 0.360000] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
[ 0.360000] MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
[ 0.360000] CPU3 revision is: 0001992f (MIPS 1004Kc)
[ 0.420000] Synchronize counters for CPU 3: done.
[ 0.430000] Brought up 4 CPUs
[ 0.430000] NET: Registered protocol family 16
[ 0.440000] MIPS: machine is HiWiFi Wireless HC5962 Board
[ 0.740000] release PCIe RST: RALINK_RSTCTRL = 7000000
[ 0.740000] PCIE PHY initialize
[ 0.750000] ***** Xtal 40MHz *****
[ 0.750000] start MT7621 PCIe register access
[ 1.340000] RALINK_RSTCTRL = 7000000
[ 1.350000] RALINK_CLKCFG1 = 77ffeff8
[ 1.350000]
[ 1.350000] *************** MT7621 PCIe RC mode *************
[ 1.850000] PCIE2 no card, disable it(RST&CLK)
[ 1.850000] pcie_link status = 0x3
[ 1.860000] RALINK_RSTCTRL= 3000000
[ 1.860000] *** Configure Device number setting of Virtual PCI-PCI bridge ***
[ 1.870000] RALINK_PCI_PCICFG_ADDR = 21007f2 -> 21007f2
[ 1.870000] PCIE0 enabled
[ 1.870000] PCIE1 enabled
[ 1.880000] interrupt enable status: 300000
[ 1.880000] Port 1 N_FTS = 1b105000
[ 1.880000] Port 0 N_FTS = 1b105000
[ 1.890000] config reg done
[ 1.890000] init_rt2880pci done
[ 1.900000] bio: create slab <bio-0> at 0
[ 1.910000] PCI host bridge to bus 0000:00
[ 1.910000] pci_bus 0000:00: root bus resource [mem 0x60000000-0x6fffffff]
[ 1.920000] pci_bus 0000:00: root bus resource [io 0x1e160000-0x1e16ffff]
[ 1.920000] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]
[ 1.930000] pci 0000:00:00.0: BAR 0: can't assign mem (size 0x80000000)
[ 1.940000] pci 0000:00:01.0: BAR 0: can't assign mem (size 0x80000000)
[ 1.950000] pci 0000:00:00.0: BAR 8: assigned [mem 0x60000000-0x600fffff]
[ 1.950000] pci 0000:00:01.0: BAR 8: assigned [mem 0x60100000-0x601fffff]
[ 1.960000] pci 0000:00:01.0: BAR 9: assigned [mem 0x60200000-0x602fffff pref]
[ 1.970000] pci 0000:00:00.0: BAR 1: assigned [mem 0x60300000-0x6030ffff]
[ 1.970000] pci 0000:00:01.0: BAR 1: assigned [mem 0x60310000-0x6031ffff]
[ 1.980000] pci 0000:01:00.0: BAR 0: assigned [mem 0x60000000-0x600fffff]
[ 1.990000] pci 0000:00:00.0: PCI bridge to [bus 01]
[ 1.990000] pci 0000:00:00.0: bridge window [mem 0x60000000-0x600fffff]
[ 2.000000] pci 0000:02:00.0: BAR 0: assigned [mem 0x60100000-0x601fffff 64bit]
[ 2.010000] pci 0000:02:00.0: BAR 6: assigned [mem 0x60200000-0x6020ffff pref]
[ 2.010000] pci 0000:00:01.0: PCI bridge to [bus 02]
[ 2.020000] pci 0000:00:01.0: bridge window [mem 0x60100000-0x601fffff]
[ 2.030000] pci 0000:00:01.0: bridge window [mem 0x60200000-0x602fffff pref]
[ 2.030000] BAR0 at slot 0 = 0
[ 2.040000] bus=0x0, slot = 0x0
[ 2.040000] BAR0 at slot 1 = 0
[ 2.040000] bus=0x0, slot = 0x1
[ 2.040000] bus=0x1, slot = 0x0, irq=0x4
[ 2.050000] bus=0x2, slot = 0x1, irq=0x18
[ 2.050000] Switching to clocksource MIPS
[ 2.060000] NET: Registered protocol family 2
[ 2.070000] TCP established hash table entries: 2048 (order: 2, 16384 bytes)
[ 2.080000] TCP bind hash table entries: 2048 (order: 2, 16384 bytes)
[ 2.090000] TCP: Hash tables configured (established 2048 bind 2048)
[ 2.090000] TCP: reno registered
[ 2.100000] UDP hash table entries: 256 (order: 1, 8192 bytes)
[ 2.100000] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
[ 2.110000] NET: Registered protocol family 1
[ 2.340000] 4 CPUs re-calibrate udelay(lpj = 2924544)
[ 2.360000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 2.370000] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 2.380000] msgmni has been set to 497
[ 2.380000] io scheduler noop registered
[ 2.390000] io scheduler deadline registered (default)
[ 2.390000] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
[ 2.400000] serial8250: ttyS0 at MMIO 0x1e000d00 (irq = 27) is a 16550A
[ 2.410000] serial8250: ttyS1 at MMIO 0x1e000c00 (irq = 26) is a 16550A
[ 2.420000] brd: module loaded
[ 2.430000] MediaTek Nand driver init, version v2.1 Fix AHB virt2phys error
[ 2.430000] Allocate 16 byte aligned buffer: 8044bdc0
[ 2.440000] Enable NFI Clock
[ 2.440000] # MTK NAND # : Use HW ECC
[ 2.450000] NAND ID [C8 D1 80 95 40, 00809540]
[ 2.450000] Device not found, ID: c8d1
[ 2.450000] Not Support this Device!
[ 2.460000] chip_mode=00000001
[ 2.460000] Support this Device in MTK table! c8d1
[ 2.470000] NAND device: Manufacturer ID: 0xc8, Chip ID: 0xd1 (Unknown NAND 128MiB 3,3V 8-bit), 128MiB, page size: 2048, OOB size: 64
[ 2.480000] [NAND]select ecc bit:4, sparesize :64 spare_per_sector=16
[ 2.480000] Scanning device for bad blocks
[ 2.630000] Signature matched and data read!
[ 2.640000] load_fact_bbt success 1023
[ 2.640000] 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
[ 2.650000] 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
[ 2.660000] 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
[ 2.670000] 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
[ 2.680000] 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
[ 2.690000] 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
[ 2.700000] 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
[ 2.710000] 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
[ 2.720000] Creating 11 MTD partitions on "MT7621-NAND":
[ 2.730000] 0x000000000000-0x000000080000 : "u-boot"
[ 2.730000] 0x000000080000-0x000000100000 : "debug"
[ 2.740000] 0x000000100000-0x000000140000 : "Factory"
[ 2.740000] 0x000000140000-0x000002140000 : "firmware"
[ 2.750000] 2 uimage-fw partitions found on MTD device firmware
[ 2.760000] 0x000000140000-0x0000002a0000 : "kernel"
[ 2.760000] 0x0000002a0000-0x000002140000 : "rootfs"
[ 2.770000] mtd: device 5 (rootfs) set to be root filesystem
[ 2.780000] 0x000002140000-0x0000021c0000 : "hw_panic"
[ 2.820000] mtdoops: Attached to MTD device 6
[ 2.820000] 0x0000021c0000-0x000002240000 : "bdinfo"
[ 2.870000] 0x000002240000-0x0000022c0000 : "backup"
[ 2.870000] 0x0000022c0000-0x0000032c0000 : "overlay"
[ 2.880000] 0x0000032c0000-0x0000052c0000 : "firmware_backup"
[ 2.890000] 0x0000052c0000-0x0000054c0000 : "oem"
[ 2.890000] 0x0000054c0000-0x000007f80000 : "opt"
[ 2.900000] [mtk_nand] probe successfully!
[ 2.900000] GMAC1_MAC_ADRH -- : 0x0000d4ee
[ 2.910000] GMAC1_MAC_ADRL -- : 0x07522fb2
[ 2.910000] PROC INIT OK!
[ 2.920000] Ralink APSoC Hardware Watchdog Timer
[ 2.920000] TCP: cubic registered
[ 2.920000] NET: Registered protocol family 17
[ 2.930000] 8021q: 802.1Q VLAN Support v1.8
[ 2.940000] drivers/rtc/hctosys.c: unable to open rtc device (rtc0)
[ 2.940000] UBIFS error (pid 1): ubifs_mount: cannot open "ubi0:rootfs", error -19
[ 2.960000] VFS: Mounted root (squashfs filesystem) readonly on device 31:5.
[ 2.960000] Freeing unused kernel memory: 224K (803d8000 - 80410000)
procd: Console is alive
[ 5.380000] usbcore: registered new interface driver usbfs
[ 5.380000] usbcore: registered new interface driver hub
[ 5.390000] usbcore: registered new device driver usb
[ 5.420000] SCSI subsystem initialized
[ 5.430000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 5.440000] ehci-platform: EHCI generic platform driver
[ 5.460000] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 5.470000] *****run project phy.
[ 5.490000] FM_OUT value: u4FmOut = 0(0x00000000)
[ 5.510000] FM_OUT value: u4FmOut = 0(0x00000000)
[ 5.530000] FM_OUT value: u4FmOut = 0(0x00000000)
[ 5.550000] FM_OUT value: u4FmOut = 0(0x00000000)
[ 5.570000] FM_OUT value: u4FmOut = 0(0x00000000)
[ 5.590000] FM_OUT value: u4FmOut = 0(0x00000000)
[ 5.610000] FM_OUT value: u4FmOut = 0(0x00000000)
[ 5.630000] FM_OUT value: u4FmOut = 0(0x00000000)
[ 5.650000] FM_OUT value: u4FmOut = 0(0x00000000)
[ 5.670000] FM_OUT value: u4FmOut = 0(0x00000000)
[ 5.730000] FM_OUT value: u4FmOut = 0(0x00000000)
[ 5.750000] FM_OUT value: u4FmOut = 0(0x00000000)
[ 5.770000] FM_OUT value: u4FmOut = 0(0x00000000)
[ 5.790000] FM_OUT value: u4FmOut = 0(0x00000000)
[ 5.810000] FM_OUT value: u4FmOut = 0(0x00000000)
[ 5.830000] FM_OUT value: u4FmOut = 0(0x00000000)
[ 5.850000] FM_OUT value: u4FmOut = 0(0x00000000)
[ 5.870000] FM_OUT value: u4FmOut = 0(0x00000000)
[ 5.890000] FM_OUT value: u4FmOut = 0(0x00000000)
[ 5.910000] FM_OUT value: u4FmOut = 0(0x00000000)
[ 6.060000] xhci-hcd xhci-hcd: xHCI Host Controller
[ 6.060000] xhci-hcd xhci-hcd: new USB bus registered, assigned bus number 1
[ 6.070000] xhci-hcd xhci-hcd: irq 22, io mem 0x1e1c0000
[ 6.080000] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[ 6.080000] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 6.090000] usb usb1: Product: xHCI Host Controller
[ 6.090000] usb usb1: Manufacturer: Linux 3.10.49 xhci-hcd
[ 6.100000] usb usb1: SerialNumber: xhci-hcd
[ 6.100000] hub 1-0:1.0: USB hub found
[ 6.110000] hub 1-0:1.0: 2 ports detected
[ 6.110000] xhci-hcd xhci-hcd: xHCI Host Controller
[ 6.120000] xhci-hcd xhci-hcd: new USB bus registered, assigned bus number 2
[ 6.120000] usb usb2: New USB device found, idVendor=1d6b, idProduct=0003
[ 6.130000] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 6.140000] usb usb2: Product: xHCI Host Controller
[ 6.140000] usb usb2: Manufacturer: Linux 3.10.49 xhci-hcd
[ 6.150000] usb usb2: SerialNumber: xhci-hcd
[ 6.150000] hub 2-0:1.0: USB hub found
[ 6.160000] hub 2-0:1.0: 1 port detected
[ 6.170000] usbcore: registered new interface driver usb-storage
procd: - preinit -
[ 6.640000] UBI: attaching mtd9 to ubi0
[ 6.790000] UBI: scanning is finished
[ 6.810000] UBI: attached mtd9 (name "overlay", size 16 MiB) to ubi0
[ 6.820000] UBI: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
[ 6.830000] UBI: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
[ 6.830000] UBI: VID header offset: 2048 (aligned 2048), data offset: 4096
[ 6.840000] UBI: good PEBs: 128, bad PEBs: 0, corrupted PEBs: 0
[ 6.850000] UBI: user volume: 1, internal volumes: 1, max. volumes count: 128
[ 6.850000] UBI: max/mean erase counter: 3/1, WL threshold: 4096, image sequence number: 2239513395
[ 6.860000] UBI: available PEBs: 0, total reserved PEBs: 128, PEBs reserved for bad PEB handling: 20
[ 6.870000] UBI: background thread "ubi_bgt0d" started, PID 382
UBI device number 0, total 128 LEBs (16252928 bytes, 15.5 MiB), available 0 LEBs (0 bytes), LEB size 126976 bytes (124.0 KiB)
[ 7.920000] UBIFS: background thread "ubifs_bgt0_0" started, PID 397
[ 8.000000] UBIFS: recovery needed
[ 8.160000] UBIFS: recovery completed
[ 8.160000] UBIFS: mounted UBI device 0, volume 0, name "overlay"
[ 8.170000] UBIFS: LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
[ 8.180000] UBIFS: FS size: 11935744 bytes (11 MiB, 94 LEBs), journal size 1015809 bytes (0 MiB, 6 LEBs)
[ 8.190000] UBIFS: reserved for root: 563754 bytes (550 KiB)
[ 8.190000] UBIFS: media format: w4/r0 (latest is w4/r0), UUID 44084DC4-24E1-4E0D-8968-E4EA7B73EE90, small LPT model
mounting /dev/root
procd: - early -
procd: - ubus -
procd: - init -
[ 10.090000] NET: Registered protocol family 10
[ 10.410000] MT7603E module init
[ 10.420000] MT7603E AP Driver version-4.0.1.0rev2.P1
[ 11.120000] MT7612E module init
[ 11.130000] MT76x2 AP Driver version-3.0.4.0.P2.20160308
[ 11.980000] device-mapper: ioctl: 4.24.0-ioctl (2013-01-15) initialised: dm-devel@redhat.com
[ 12.010000] Initializing XFRM netlink socket
[ 12.010000] NET: Registered protocol family 15
[ 12.030000] loop: module loaded
[ 12.060000] l2tp_core: L2TP core driver, V2.0
[ 12.070000] l2tp_netlink: L2TP netlink interface
[ 12.080000] sit: IPv6 over IPv4 tunneling driver
[ 12.090000] exFAT: Version 1.2.9
[ 12.100000] gre: GRE over IPv4 demultiplexor driver
[ 12.100000] ip_gre: GRE over IPv4 tunneling driver
[ 12.120000] nf_conntrack version 0.5.0 (3984 buckets, 15936 max)
[ 12.130000] ip6_tables: (C) 2000-2006 Netfilter Core Team
[ 12.150000] Netfilter messages via NETLINK v0.30.
[ 12.160000] ip_set: protocol 6
[ 12.190000] ***Module syslog inserted(log_addr:8d5dc000)***
[ 12.210000] i2c-gpio i2c-gpio.0: using pins 3 (SDA) and 4 (SCL)
[ 12.230000] u32 classifier
[ 12.230000] input device check on
[ 12.240000] Actions configured
[ 12.240000] Mirror/redirect action on
[ 12.250000] Failed to load ipt action
[ 12.280000] fuse init (API version 7.22)
[ 12.290000] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 12.400000] ctnetlink v0.93: registering with nfnetlink.
[ 13.430000] rtc-pt7c4338 0-0068: rtc core: registered pt7c4338 as rtc0
[ 13.480000] xt_time: kernel timezone is -0000
[ 13.500000] PPP generic driver version 2.4.2
[ 13.500000] PPP MPPE Compression module registered
[ 13.510000] NET: Registered protocol family 24
[ 13.550000] p p t p driver version 0.8.5
[ 13.560000] l2tp_ppp: PPPoL2TP kernel driver, V2.0
[ 15.110000] oem: use pcba GM2101v01
Nov 8 10:51:54 Hiwifi kern.alert kernel: [ 2.910000] PROC INIT OK!
[ 20.220000] phy_free_head is 0xd2d6000!!!
[ 20.230000] phy_free_tail_phy is 0xd2d7ff0!!!
[ 20.230000] txd_pool=ad2f0000 phy_txd_pool=0D2F0000
[ 20.230000] ei_local->skb_free start address is 0x8fe82a64.
[ 20.240000] free_txd: ad2f0010, ei_local->cpu_ptr: 0D2F0000
[ 20.250000] POOL HEAD_PTR | DMA_PTR | CPU_PTR
[ 20.250000] ----------------+---------+--------
[ 20.260000] 0xad2f0000 0x0D2F0000 0x0D2F0000
[ 20.260000]
[ 20.260000] phy_qrx_ring = 0x0d2ca000, qrx_ring = 0xad2ca000
[ 20.270000]
[ 20.270000] phy_rx_ring0 = 0x0d0d4000, rx_ring0 = 0xad0d4000
[ 20.300000] MT7530 Reset Completed!!
[ 20.310000] GMAC1_MAC_ADRH -- : 0x0000d4ee
[ 20.310000] GMAC1_MAC_ADRL -- : 0x07522fb2
[ 20.310000] GDMA2_MAC_ADRH -- : 0x0000d4ee
[ 20.320000] GDMA2_MAC_ADRL -- : 0x07522fb3
[ 20.550000] ra2880stop()...Done
[ 20.550000] Free TX/RX Ring Memory!
[ 20.560000] phy_free_head is 0xd0d4000!!!
[ 20.570000] phy_free_tail_phy is 0xd0d5ff0!!!
[ 20.570000] txd_pool=ad100000 phy_txd_pool=0D100000
[ 20.580000] ei_local->skb_free start address is 0x8fe82a64.
[ 20.580000] free_txd: ad100010, ei_local->cpu_ptr: 0D100000
[ 20.590000] POOL HEAD_PTR | DMA_PTR | CPU_PTR
[ 20.590000] ----------------+---------+--------
[ 20.600000] 0xad100000 0x0D100000 0x0D100000
[ 20.600000]
[ 20.600000] phy_qrx_ring = 0x0d047000, qrx_ring = 0xad047000
[ 20.610000]
[ 20.610000] phy_rx_ring0 = 0x0d0e0000, rx_ring0 = 0xad0e0000
[ 20.640000] MT7530 Reset Completed!!
[ 20.650000] GMAC1_MAC_ADRH -- : 0x0000d4ee
[ 20.650000] GMAC1_MAC_ADRL -- : 0x07522fb2
[ 20.660000] device eth2 entered promiscuous mode
[ 20.660000] br-lan: port 1(eth2) entered forwarding state
[ 20.670000] br-lan: port 1(eth2) entered forwarding state
[ 20.690000] device eth2.3 entered promiscuous mode
[ 20.690000] br-lan1: port 1(eth2.3) entered forwarding state
[ 20.700000] br-lan1: port 1(eth2.3) entered forwarding state
[ 21.690000] UBI: attaching mtd12 to ubi1
[ 22.100000] device ra0 entered promiscuous mode
[ 22.100000] br-lan: port 2(ra0) entered forwarding state
[ 22.110000] br-lan: port 2(ra0) entered forwarding state
[ 22.140000] UBI: scanning is finished
[ 22.160000] UBI: attached mtd12 (name "opt", size 42 MiB) to ubi1
[ 22.170000] UBI: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
[ 22.180000] UBI: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
[ 22.180000] UBI: VID header offset: 2048 (aligned 2048), data offset: 4096
[ 22.190000] UBI: good PEBs: 342, bad PEBs: 0, corrupted PEBs: 0
[ 22.200000] UBI: user volume: 1, internal volumes: 1, max. volumes count: 128
[ 22.200000] UBI: max/mean erase counter: 3/2, WL threshold: 4096, image sequence number: 2926461731
[ 22.210000] UBI: available PEBs: 0, total reserved PEBs: 342, PEBs reserved for bad PEB handling: 20
[ 22.220000] UBI: background thread "ubi_bgt1d" started, PID 1888
[ 22.280000] UBIFS: background thread "ubifs_bgt1_0" started, PID 1898
[ 22.370000] UBIFS: mounted UBI device 1, volume 0, name "opt"
[ 22.370000] UBIFS: LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
[ 22.380000] UBIFS: FS size: 39108608 bytes (37 MiB, 308 LEBs), journal size 1904640 bytes (1 MiB, 15 LEBs)
[ 22.390000] UBIFS: reserved for root: 1847195 bytes (1803 KiB)
[ 22.400000] UBIFS: media format: w4/r0 (latest is w4/r0), UUID AC84C9D5-D3FF-4D0C-B391-CCE751A6BA11, small LPT model
[ 22.520000] device rai0 entered promiscuous mode
[ 22.530000] br-lan: port 3(rai0) entered forwarding state
[ 22.530000] br-lan: port 3(rai0) entered forwarding state
[ 22.670000] br-lan: port 1(eth2) entered forwarding state
[ 22.700000] br-lan1: port 1(eth2.3) entered forwarding state
[ 23.560000] ethernet: port3 linkup(interrupt)
[ 23.820000] Simple address matching list for Netfilter - HiWiFi
[ 24.110000] br-lan: port 2(ra0) entered forwarding state
[ 24.530000] br-lan: port 3(rai0) entered forwarding state
[ 25.910000] [NOTICE] <HWF-Kproxy> (hwf_kproxy_init:2227) kproxy hook prioriy -101
[ 25.920000] [NOTICE] <HWF-Kproxy> (hwf_kproxy_init:2241) Module is inserted
[ 31.010000] Welcome to ipstat_init eth3[ 35.860000] Started WatchDog Timer.
[ 35.860000] Started WatchDog Timer.
procd: - init complete -

复制代码

xiaojuzi · 发表于 2017-2-21 16:43

本帖最后由 xiaojuzi 于 2017-2-21 16:52 编辑

另外。根据飞哥给我的ttl定义图，我用我的设备没有输出。如图，后来我吧tx 和 rx 对调一下就好了。各位可以参考

下面是刷了

20170125-openwrt-kunteng-ramips-mt7621-nand-hc5962-squashfs-sysupgrade (1) (1).bin 这个固件的启动信息

Enable NFI Clock
# MTK NAND # : Use HW ECC
NAND ID [C8 D1 80 95 40]
Device not found, ID: c8d1
Not Support this Device!
chip_mode=00000001
Support this Device in MTK table! c8d1
select_chip
[NAND]select ecc bit:4, sparesize :64 spare_per_sector=16
Signature matched and data read!
load_fact_bbt success 1023
load fact bbt success
[mtk_nand] probe successfully!
mtd->writesize=2048 mtd->oobsize=64, mtd->erasesize=131072 devinfo.iowidth=8
.*** Warning - bad CRC, using default environment
dcache: sets:256, ways:4, linesz:32 ,total:32768
##### The CPU freq = 880 MHZ ####
estimate memory size =256 Mbytes
#Reset_MT7530
set LAN/WAN LLLLW
0
firmware_backup is not equal to firmware!
=================================================
Check firmware_backup :
Header Magic Number --> Failed
=================================================
firmware_backup: broken!
3: System Boot system code via Flash.
## Booting image at bc140000 ...
Image Name: MIPS OpenWrt Linux-3.18.23
Image Type: MIPS Linux Kernel Image (lzma compressed)
Data Size: 1365289 Bytes = 1.3 MB
Load Address: 80001000
Entry Point: 80001000
..................... Verifying Checksum ... OK
Uncompressing Kernel Image ... OK
No initrd
## Transferring control to Linux (at address 80001000) ...
## Giving linux memsize in MB, 256
Starting kernel ...
[ 0.000000] Linux version 3.18.23 (zhangzf@ROM-DSS1500) (gcc version 4.8.3 (OpenWrt/Linaro GCC 4.8-2014.04 r47727) ) #33 SMP Wed Jan 25 18:27:24 CST 2017
[ 0.000000] SoC Type: MediaTek MT7621 ver:1 eco:3
[ 0.000000] bootconsole [early0] enabled
[ 0.000000] CPU0 revision is: 0001992f (MIPS 1004Kc)
[ 0.000000] MIPS: machine is HiWiFi HC5962
[ 0.000000] Determined physical RAM map:
[ 0.000000] memory: 10000000 @ 00000000 (usable)
[ 0.000000] Initrd not found or empty - disabling initrd
[ 0.000000] Zone ranges:
[ 0.000000] Normal [mem 0x00000000-0x0fffffff]
[ 0.000000] HighMem empty
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x00000000-0x0fffffff]
[ 0.000000] Initmem setup node 0 [mem 0x00000000-0x0fffffff]
[ 0.000000] Detected 3 available secondary CPU(s)
[ 0.000000] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
[ 0.000000] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
[ 0.000000] MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
[ 0.000000] PERCPU: Embedded 9 pages/cpu @8120b000 s5696 r8192 d22976 u36864
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 65024
[ 0.000000] Kernel command line: console=ttyS0,115200 rootfstype=squashfs,jffs2
[ 0.000000] PID hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
[ 0.000000] Writing ErrCtl register=00001087
[ 0.000000] Readback ErrCtl register=00001087
[ 0.000000] Memory: 255320K/262144K available (3089K kernel code, 171K rwdata, 612K rodata, 212K init, 241K bss, 6824K reserved, 0K highmem)
[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
[ 0.000000] Hierarchical RCU implementation.
[ 0.000000] NR_IRQS:256
[ 0.000000] gic: revision 3.0
[ 0.000000] CPU Clock: 880MHz
[ 0.000000] Calibrating delay loop... 577.53 BogoMIPS (lpj=2887680)
[ 0.050000] pid_max: default: 32768 minimum: 301
[ 0.050000] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.060000] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.060000] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
[ 0.060000] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
[ 0.060000] MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
[ 0.060000] CPU1 revision is: 0001992f (MIPS 1004Kc)
[ 0.150000] Synchronize counters for CPU 1: done.
[ 0.150000] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
[ 0.150000] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
[ 0.150000] MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
[ 0.150000] CPU2 revision is: 0001992f (MIPS 1004Kc)
[ 0.230000] Synchronize counters for CPU 2: done.
[ 0.240000] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
[ 0.240000] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
[ 0.240000] MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
[ 0.240000] CPU3 revision is: 0001992f (MIPS 1004Kc)
[ 0.320000] Synchronize counters for CPU 3: done.
[ 0.330000] Brought up 4 CPUs
[ 0.340000] pinctrl core: initialized pinctrl subsystem
[ 0.340000] NET: Registered protocol family 16
[ 0.350000] pull PCIe RST: RALINK_RSTCTRL = 0
[ 0.650000] release PCIe RST: RALINK_RSTCTRL = 7000000
[ 0.650000] ***** Xtal 40MHz *****
[ 0.660000] release PCIe RST: RALINK_RSTCTRL = 7000000
[ 0.660000] Port 0 N_FTS = 1b105000
[ 0.660000] Port 1 N_FTS = 1b105000
[ 0.670000] Port 2 N_FTS = 1b102800
[ 1.800000] PCIE2 no card, disable it(RST&CLK)
[ 1.810000] -> 21007f2
[ 1.810000] PCIE0 enabled
[ 1.810000] PCIE1 enabled
[ 1.810000] PCI host bridge /pcie@1e140000 ranges:
[ 1.820000] MEM 0x0000000060000000..0x000000006fffffff
[ 1.820000] IO 0x000000001e160000..0x000000001e16ffff
[ 1.860000] mt7621_gpio 1e000600.gpio: registering 32 gpios
[ 1.860000] mt7621_gpio 1e000600.gpio: registering 32 gpios
[ 1.870000] mt7621_gpio 1e000600.gpio: registering 32 gpios
[ 1.870000] PCI host bridge to bus 0000:00
[ 1.880000] pci_bus 0000:00: root bus resource [mem 0x60000000-0x6fffffff]
[ 1.880000] pci_bus 0000:00: root bus resource [io 0xffffffff]
[ 1.890000] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]
[ 1.900000] pci 0000:00:00.0: BAR 0: no space for [mem size 0x80000000]
[ 1.910000] pci 0000:00:00.0: BAR 0: failed to assign [mem size 0x80000000]
[ 1.910000] pci 0000:00:01.0: BAR 0: no space for [mem size 0x80000000]
[ 1.920000] pci 0000:00:01.0: BAR 0: failed to assign [mem size 0x80000000]
[ 1.930000] pci 0000:00:00.0: BAR 8: assigned [mem 0x60000000-0x600fffff]
[ 1.930000] pci 0000:00:01.0: BAR 8: assigned [mem 0x60100000-0x601fffff]
[ 1.940000] pci 0000:00:01.0: BAR 9: assigned [mem 0x60200000-0x602fffff pref]
[ 1.950000] pci 0000:00:00.0: BAR 1: assigned [mem 0x60300000-0x6030ffff]
[ 1.950000] pci 0000:00:01.0: BAR 1: assigned [mem 0x60310000-0x6031ffff]
[ 1.960000] pci 0000:01:00.0: BAR 0: assigned [mem 0x60000000-0x600fffff]
[ 1.970000] pci 0000:00:00.0: PCI bridge to [bus 01]
[ 1.970000] pci 0000:00:00.0: bridge window [mem 0x60000000-0x600fffff]
[ 1.980000] pci 0000:02:00.0: BAR 0: assigned [mem 0x60100000-0x601fffff 64bit]
[ 1.990000] pci 0000:02:00.0: BAR 6: assigned [mem 0x60200000-0x6020ffff pref]
[ 1.990000] pci 0000:00:01.0: PCI bridge to [bus 02]
[ 2.000000] pci 0000:00:01.0: bridge window [mem 0x60100000-0x601fffff]
[ 2.010000] pci 0000:00:01.0: bridge window [mem 0x60200000-0x602fffff pref]
[ 2.010000] BAR0 at slot 0 = 0
[ 2.020000] bus=0x0, slot = 0x0
[ 2.020000] BAR0 at slot 1 = 0
[ 2.020000] bus=0x0, slot = 0x1
[ 2.030000] bus=0x1, slot = 0x0, irq=0xff
[ 2.030000] bus=0x2, slot = 0x1, irq=0xff
[ 2.030000] Switched to clocksource MIPS
[ 2.040000] NET: Registered protocol family 2
[ 2.050000] TCP established hash table entries: 2048 (order: 1, 8192 bytes)
[ 2.050000] TCP bind hash table entries: 2048 (order: 2, 16384 bytes)
[ 2.060000] TCP: Hash tables configured (established 2048 bind 2048)
[ 2.060000] TCP: reno registered
[ 2.070000] UDP hash table entries: 256 (order: 1, 8192 bytes)
[ 2.070000] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
[ 2.080000] NET: Registered protocol family 1
[ 2.090000] futex hash table entries: 1024 (order: 4, 65536 bytes)
[ 2.100000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 2.100000] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 2.120000] msgmni has been set to 498
[ 2.120000] io scheduler noop registered
[ 2.120000] io scheduler deadline registered (default)
[ 2.130000] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
[ 2.140000] console [ttyS0] disabled
[ 2.140000] 1e000c00.uartlite: ttyS0 at MMIO 0x1e000c00 (irq = 34, base_baud = 3125000) is a 16550A
[ 2.150000] console [ttyS0] enabled
[ 2.150000] console [ttyS0] enabled
[ 2.160000] bootconsole [early0] disabled
[ 2.160000] bootconsole [early0] disabled
[ 2.160000] MediaTek Nand driver init, version v2.1 Fix AHB virt2phys error
[ 2.170000] Allocate 16 byte aligned buffer: 80434370
[ 2.180000] Enable NFI Clock
[ 2.180000] # MTK NAND # : Use HW ECC
[ 2.180000] Device not found, ID: c8d1
[ 2.190000] Not Support this Device!
[ 2.190000] chip_mode=00000001
[ 2.190000] Support this Device in MTK table! c8d1
[ 2.200000] nand: device found, Manufacturer ID: 0xc8, Chip ID: 0xd1
[ 2.200000] nand: Unknown NAND 128MiB 3,3V 8-bit
[ 2.210000] nand: 128MiB, SLC, page size: 2048, OOB size: 64
[ 2.220000] [NAND]select ecc bit:4, sparesize :64 spare_per_sector=16
[ 2.220000] Scanning device for bad blocks
[ 2.370000] 13 ofpart partitions found on MTD device MT7621-NAND
[ 2.380000] Creating 13 MTD partitions on "MT7621-NAND":
[ 2.380000] 0x000000000000-0x000000080000 : "u-boot"
[ 2.390000] 0x000000080000-0x000000100000 : "debug"
[ 2.390000] 0x000000100000-0x000000140000 : "factory"
[ 2.400000] 0x000000140000-0x000000340000 : "kernel"
[ 2.400000] 0x000000140000-0x000002140000 : "firmware"
[ 3.000000] 0x000000340000-0x000002140000 : "ubi"
[ 3.000000] 0x000002140000-0x0000021c0000 : "hw_panic"
[ 3.010000] 0x0000021c0000-0x000002240000 : "bdinfo"
[ 3.010000] 0x000002240000-0x0000022c0000 : "backup"
[ 3.020000] 0x0000022c0000-0x0000032c0000 : "overly"
[ 3.020000] 0x0000032c0000-0x0000052c0000 : "firmware_backup"
[ 3.030000] 0x0000052c0000-0x0000054c0000 : "oem"
[ 3.040000] 0x0000054c0000-0x000007f80000 : "opt"
[ 3.040000] [mtk_nand] probe successfully!
[ 3.050000] Signature matched and data read!
[ 3.050000] load_fact_bbt success 1023
[ 3.050000] netif_napi_add() called with weight 128 on device eth%d
[ 3.070000] change HW-TRAP to 0x17ccf
[ 3.080000] ralink_soc_eth 1e100000.ethernet: generated random MAC address 8e:ac:e0:12:30:2a
[ 3.090000] libphy: mdio: probed
[ 3.100000] ralink_soc_eth 1e100000.ethernet: loaded mt7530 driver
[ 3.110000] ralink_soc_eth 1e100000.ethernet eth0: ralink at 0xbe100000, irq 11
[ 3.120000] mt7621_wdt 1e000100.wdt: Initialized
[ 3.120000] TCP: cubic registered
[ 3.120000] NET: Registered protocol family 17
[ 3.130000] bridge: automatic filtering via arp/ip/ip6tables has been deprecated. Update your scripts to load br_netfilter if you need this.
[ 3.140000] 8021q: 802.1Q VLAN Support v1.8
[ 3.150000] UBI: auto-attach mtd5
[ 3.150000] UBI: attaching mtd5 to ubi0
[ 3.260000] UBI: EOF marker found, PEBs from 90 will be erased
[ 3.270000] UBI: scanning is finished
[ 3.310000] UBI: volume 1 ("rootfs_data") re-sized from 9 to 128 LEBs
[ 3.320000] UBI: attached mtd5 (name "ubi", size 30 MiB) to ubi0
[ 3.320000] UBI: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
[ 3.330000] UBI: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
[ 3.340000] UBI: VID header offset: 2048 (aligned 2048), data offset: 4096
[ 3.350000] UBI: good PEBs: 240, bad PEBs: 0, corrupted PEBs: 0
[ 3.350000] UBI: user volume: 2, internal volumes: 1, max. volumes count: 128
[ 3.360000] UBI: max/mean erase counter: 1/0, WL threshold: 4096, image sequence number: 1825856685
[ 3.370000] UBI: available PEBs: 0, total reserved PEBs: 240, PEBs reserved for bad PEB handling: 20
[ 3.380000] UBI: background thread "ubi_bgt0d" started, PID 299
[ 3.380000] UBI: ubiblock0_0 created from ubi0:0(rootfs)
[ 3.380000] ubiblock: device ubiblock0_0 (rootfs) set to be root filesystem
[ 3.420000] VFS: Mounted root (squashfs filesystem) readonly on device 254:0.
[ 3.420000] Freeing unused kernel memory: 212K (803cb000 - 80400000)
[ 4.540000] init: Console is alive
[ 4.540000] init: - watchdog -
[ 4.670000] ralink_soc_eth 1e100000.ethernet eth0: port 4 link up
[ 6.150000] usbcore: registered new interface driver usbfs
[ 6.150000] usbcore: registered new interface driver hub
[ 6.160000] usbcore: registered new device driver usb
[ 6.190000] SCSI subsystem initialized
[ 6.190000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 6.200000] ehci-platform: EHCI generic platform driver
[ 6.220000] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 6.230000] ohci-platform: OHCI generic platform driver
[ 6.270000] FM_OUT value: u4FmOut = 0(0x00000000)
[ 6.290000] FM_OUT value: u4FmOut = 0(0x00000000)
[ 6.310000] FM_OUT value: u4FmOut = 0(0x00000000)
[ 6.330000] FM_OUT value: u4FmOut = 0(0x00000000)
[ 6.350000] FM_OUT value: u4FmOut = 0(0x00000000)
[ 6.370000] FM_OUT value: u4FmOut = 0(0x00000000)
[ 6.390000] FM_OUT value: u4FmOut = 0(0x00000000)
[ 6.410000] FM_OUT value: u4FmOut = 0(0x00000000)
[ 6.430000] FM_OUT value: u4FmOut = 0(0x00000000)
[ 6.450000] FM_OUT value: u4FmOut = 0(0x00000000)
[ 6.510000] FM_OUT value: u4FmOut = 0(0x00000000)
[ 6.530000] FM_OUT value: u4FmOut = 0(0x00000000)
[ 6.550000] FM_OUT value: u4FmOut = 0(0x00000000)
[ 6.570000] FM_OUT value: u4FmOut = 0(0x00000000)
[ 6.590000] FM_OUT value: u4FmOut = 0(0x00000000)
[ 6.610000] FM_OUT value: u4FmOut = 0(0x00000000)
[ 6.630000] FM_OUT value: u4FmOut = 0(0x00000000)
[ 6.650000] FM_OUT value: u4FmOut = 0(0x00000000)
[ 6.670000] FM_OUT value: u4FmOut = 0(0x00000000)
[ 6.690000] FM_OUT value: u4FmOut = 0(0x00000000)
[ 6.840000] xhci-hcd xhci-hcd: xHCI Host Controller
[ 6.840000] xhci-hcd xhci-hcd: new USB bus registered, assigned bus number 1
[ 6.850000] xhci-hcd xhci-hcd: irq 30, io mem 0x1e1c0000
[ 6.860000] hub 1-0:1.0: USB hub found
[ 6.860000] hub 1-0:1.0: 2 ports detected
[ 6.870000] xhci-hcd xhci-hcd: xHCI Host Controller
[ 6.870000] xhci-hcd xhci-hcd: new USB bus registered, assigned bus number 2
[ 6.870000] ralink_soc_eth 1e100000.ethernet eth0: port 3 link up
[ 6.880000] hub 2-0:1.0: USB hub found
[ 6.890000] hub 2-0:1.0: 1 port detected
[ 6.900000] usbcore: registered new interface driver usb-storage
[ 7.350000] random: nonblocking pool is initialized
[ 7.540000] init: - preinit -
Press the [f] key and hit [enter] to enter failsafe mode
Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level
[ 11.070000] mount_root: loading kmods from internal overlay
[ 11.450000] UBIFS: default file-system created
[ 11.460000] UBIFS: background thread "ubifs_bgt0_1" started, PID 411
[ 11.570000] UBIFS: mounted UBI device 0, volume 1, name "rootfs_data"
[ 11.580000] UBIFS: LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
[ 11.590000] UBIFS: FS size: 14983168 bytes (14 MiB, 118 LEBs), journal size 1015809 bytes (0 MiB, 6 LEBs)
[ 11.590000] UBIFS: reserved for root: 707691 bytes (691 KiB)
[ 11.600000] UBIFS: media format: w4/r0 (latest is w4/r0), UUID 30CACBB9-0163-4B55-9EE3-1367883FBE53, small LPT model
[ 11.610000] block: attempting to load /tmp/ubifs_cfg/upper/etc/config/fstab
[ 11.620000] block: unable to load configuration (fstab: Entry not found)
[ 11.630000] block: attempting to load /tmp/ubifs_cfg/etc/config/fstab
[ 11.630000] block: unable to load configuration (fstab: Entry not found)
[ 11.640000] block: attempting to load /etc/config/fstab
[ 11.640000] block: unable to load configuration (fstab: Entry not found)
[ 11.650000] block: no usable configuration
[ 11.690000] UBIFS: un-mount UBI device 0, volume 1
[ 11.690000] UBIFS: background thread "ubifs_bgt0_1" stops
[ 11.710000] UBIFS: background thread "ubifs_bgt0_1" started, PID 414
[ 11.820000] UBIFS: mounted UBI device 0, volume 1, name "rootfs_data"
[ 11.820000] UBIFS: LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
[ 11.830000] UBIFS: FS size: 14983168 bytes (14 MiB, 118 LEBs), journal size 1015809 bytes (0 MiB, 6 LEBs)
[ 11.840000] UBIFS: reserved for root: 707691 bytes (691 KiB)
[ 11.850000] UBIFS: media format: w4/r0 (latest is w4/r0), UUID 30CACBB9-0163-4B55-9EE3-1367883FBE53, small LPT model
[ 12.110000] block: attempting to load /tmp/ubifs_cfg/upper/etc/config/fstab
[ 12.120000] block: unable to load configuration (fstab: Entry not found)
[ 12.120000] block: attempting to load /tmp/ubifs_cfg/etc/config/fstab
[ 12.130000] block: unable to load configuration (fstab: Entry not found)
[ 12.140000] block: attempting to load /etc/config/fstab
[ 12.140000] block: unable to load configuration (fstab: Entry not found)
[ 12.150000] block: no usable configuration
[ 12.210000] mount_root: overlay filesystem has not been fully initialized yet
[ 12.210000] mount_root: switching to jffs2 overlay
[ 12.330000] UBI: attaching mtd12 to ubi1
[ 12.740000] UBI: scanning is finished
[ 12.760000] UBI: attached mtd12 (name "opt", size 42 MiB) to ubi1
[ 12.770000] UBI: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
[ 12.780000] UBI: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
[ 12.780000] UBI: VID header offset: 2048 (aligned 2048), data offset: 4096
[ 12.790000] UBI: good PEBs: 342, bad PEBs: 0, corrupted PEBs: 0
[ 12.800000] UBI: user volume: 1, internal volumes: 1, max. volumes count: 128
[ 12.800000] UBI: max/mean erase counter: 3/2, WL threshold: 4096, image sequence number: 2926461731
[ 12.810000] UBI: available PEBs: 0, total reserved PEBs: 342, PEBs reserved for bad PEB handling: 20
[ 12.820000] UBI: background thread "ubi_bgt1d" started, PID 433
UBI device number 1, total 342 LEBs (43425792 bytes, 41.4 MiB), available 0 LEBs (0 bytes), LEB size 126976 bytes (124.0 KiB)
[ 12.890000] UBIFS: background thread "ubifs_bgt1_0" started, PID 451
[ 13.010000] UBIFS: mounted UBI device 1, volume 0, name "opt"
[ 13.010000] UBIFS: LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
[ 13.020000] UBIFS: FS size: 39108608 bytes (37 MiB, 308 LEBs), journal size 1904640 bytes (1 MiB, 15 LEBs)
[ 13.030000] UBIFS: reserved for root: 1847195 bytes (1803 KiB)
[ 13.040000] UBIFS: media format: w4/r0 (latest is w4/r0), UUID AC84C9D5-D3FF-4D0C-B391-CCE751A6BA11, small LPT model
[ 13.070000] procd: - early -
[ 13.070000] procd: - watchdog -
[ 13.760000] procd: - ubus -
[ 14.770000] procd: - init -
Please press Enter to activate this console.
[ 16.290000] NET: Registered protocol family 10
[ 16.310000] ntfs: driver 2.1.31 [Flags: R/O MODULE].
[ 16.310000] nls_base: exports duplicate symbol __register_nls (owned by kernel)
[ 16.360000] nls_base: exports duplicate symbol __register_nls (owned by kernel)
[ 16.390000] loop: module loaded
[ 16.400000] nls_base: exports duplicate symbol __register_nls (owned by kernel)
[ 16.460000] nls_base: exports duplicate symbol __register_nls (owned by kernel)
[ 16.510000] nls_base: exports duplicate symbol __register_nls (owned by kernel)
[ 16.570000] tun: Universal TUN/TAP device driver, 1.6
[ 16.570000] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
[ 16.580000] nls_base: exports duplicate symbol __register_nls (owned by kernel)
[ 16.640000] nls_base: exports duplicate symbol __register_nls (owned by kernel)
[ 16.680000] ip6_tables: (C) 2000-2006 Netfilter Core Team
[ 16.680000] nls_base: exports duplicate symbol __register_nls (owned by kernel)
[ 16.750000] nls_base: exports duplicate symbol __register_nls (owned by kernel)
[ 16.780000] nls_base: exports duplicate symbol __register_nls (owned by kernel)
[ 16.810000] nls_base: exports duplicate symbol __register_nls (owned by kernel)
[ 16.850000] nls_base: exports duplicate symbol __register_nls (owned by kernel)
[ 16.880000] nls_base: exports duplicate symbol __register_nls (owned by kernel)
[ 16.910000] nls_base: exports duplicate symbol __register_nls (owned by kernel)
[ 16.940000] nls_base: exports duplicate symbol __register_nls (owned by kernel)
[ 16.970000] nls_base: exports duplicate symbol __register_nls (owned by kernel)
[ 17.000000] nls_base: exports duplicate symbol __register_nls (owned by kernel)
[ 17.030000] nls_base: exports duplicate symbol __register_nls (owned by kernel)
[ 17.080000] Netfilter messages via NETLINK v0.30.
[ 17.080000] nls_base: exports duplicate symbol __register_nls (owned by kernel)
[ 17.130000] ip_set: protocol 6
[ 17.130000] nls_base: exports duplicate symbol __register_nls (owned by kernel)
[ 17.250000] nls_base: exports duplicate symbol __register_nls (owned by kernel)
[ 17.340000] nls_base: exports duplicate symbol __register_nls (owned by kernel)
[ 17.430000] nls_base: exports duplicate symbol __register_nls (owned by kernel)
[ 17.480000] nls_base: exports duplicate symbol __register_nls (owned by kernel)
[ 17.580000] nls_base: exports duplicate symbol __register_nls (owned by kernel)
[ 17.660000] nls_base: exports duplicate symbol __register_nls (owned by kernel)
[ 17.730000] nls_base: exports duplicate symbol __register_nls (owned by kernel)
[ 17.800000] nls_base: exports duplicate symbol __register_nls (owned by kernel)
[ 17.850000] nls_base: exports duplicate symbol __register_nls (owned by kernel)
[ 17.900000] nls_base: exports duplicate symbol __register_nls (owned by kernel)
[ 18.020000] nls_base: exports duplicate symbol __register_nls (owned by kernel)
[ 18.070000] nls_base: exports duplicate symbol __register_nls (owned by kernel)
[ 18.100000] nls_base: exports duplicate symbol __register_nls (owned by kernel)
[ 18.140000] nls_base: exports duplicate symbol __register_nls (owned by kernel)
[ 18.180000] nls_base: exports duplicate symbol __register_nls (owned by kernel)
[ 18.220000] nls_base: exports duplicate symbol __register_nls (owned by kernel)
[ 18.280000] nls_base: exports duplicate symbol __register_nls (owned by kernel)
[ 18.310000] nls_base: exports duplicate symbol __register_nls (owned by kernel)
[ 18.340000] nls_base: exports duplicate symbol __register_nls (owned by kernel)
[ 18.380000] nls_base: exports duplicate symbol __register_nls (owned by kernel)
[ 18.420000] nls_base: exports duplicate symbol __register_nls (owned by kernel)
[ 18.460000] nls_base: exports duplicate symbol __register_nls (owned by kernel)
[ 18.500000] nls_base: exports duplicate symbol __register_nls (owned by kernel)
[ 18.540000] nls_base: exports duplicate symbol __register_nls (owned by kernel)
[ 18.580000] nls_base: exports duplicate symbol __register_nls (owned by kernel)
[ 18.620000] nls_base: exports duplicate symbol __register_nls (owned by kernel)
[ 18.660000] nls_base: exports duplicate symbol __register_nls (owned by kernel)
[ 18.700000] nls_base: exports duplicate symbol __register_nls (owned by kernel)
[ 18.740000] nls_base: exports duplicate symbol __register_nls (owned by kernel)
[ 18.780000] nls_base: exports duplicate symbol __register_nls (owned by kernel)
[ 18.830000] nls_base: exports duplicate symbol __register_nls (owned by kernel)
[ 18.860000] nls_base: exports duplicate symbol __register_nls (owned by kernel)
[ 18.890000] nls_base: exports duplicate symbol __register_nls (owned by kernel)
[ 18.960000] nls_base: exports duplicate symbol __register_nls (owned by kernel)
[ 19.010000] nls_base: exports duplicate symbol __register_nls (owned by kernel)
[ 19.180000] nls_base: exports duplicate symbol __register_nls (owned by kernel)
[ 19.280000] nls_base: exports duplicate symbol __register_nls (owned by kernel)
[ 19.470000] nls_base: exports duplicate symbol __register_nls (owned by kernel)
[ 19.520000] nls_base: exports duplicate symbol __register_nls (owned by kernel)
[ 19.590000] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 19.600000] nf_conntrack version 0.5.0 (3992 buckets, 15968 max)
[ 19.610000] ctnetlink v0.93: registering with nfnetlink.
[ 19.740000] nls_base: exports duplicate symbol __register_nls (owned by kernel)
[ 19.770000] usbcore: registered new interface driver ums-alauda
[ 19.770000] usbcore: registered new interface driver ums-cypress
[ 19.780000] usbcore: registered new interface driver ums-datafab
[ 19.790000] usbcore: registered new interface driver ums-freecom
[ 19.800000] usbcore: registered new interface driver ums-isd200
[ 19.800000] usbcore: registered new interface driver ums-jumpshot
[ 19.810000] usbcore: registered new interface driver ums-karma
[ 19.820000] usbcore: registered new interface driver ums-sddr09
[ 19.820000] usbcore: registered new interface driver ums-sddr55
[ 19.830000] usbcore: registered new interface driver ums-usbat
[ 19.860000] xt_time: kernel timezone is -0000
[ 19.870000] nls_base: exports duplicate symbol __register_nls (owned by kernel)
[ 19.920000] PPP generic driver version 2.4.2
[ 19.920000] NET: Registered protocol family 24
[ 19.930000] nls_base: exports duplicate symbol __register_nls (owned by kernel)
[ 19.980000] nls_base: exports duplicate symbol __register_nls (owned by kernel)
[ 24.240000] device eth0.1 entered promiscuous mode
[ 24.250000] device eth0 entered promiscuous mode
[ 24.260000] br-lan: port 1(eth0.1) entered forwarding state
[ 24.260000] br-lan: port 1(eth0.1) entered forwarding state
[ 25.790000] efuse_probe: efuse = 10000002
[ 25.970000] tssi_1_target_pwr_g_band = 12
[ 25.970000] netlink kernel mscan init......
[ 26.260000] br-lan: port 1(eth0.1) entered forwarding state
[ 29.210000] device ra0 entered promiscuous mode
[ 29.210000] br-lan: port 2(ra0) entered forwarding state
[ 29.220000] br-lan: port 2(ra0) entered forwarding state
[ 29.610000] 62,76, 1, 0,fc
[ 29.680000] 62,76, 1, 0,fc
[ 29.680000] netlink kernel mscan init......
[ 30.800000] device rai0 entered promiscuous mode
[ 30.810000] br-lan: port 3(rai0) entered forwarding state
[ 30.810000] br-lan: port 3(rai0) entered forwarding state
[ 31.220000] br-lan: port 2(ra0) entered forwarding state
first startup
[ 32.810000] br-lan: port 3(rai0) entered forwarding state

复制代码

AIRSHAPE · 发表于 2017-2-21 17:16

已经下车，垃圾路由卡的一b

恩五 · 发表于 2017-2-21 22:11

支持折腾。

newscat · 发表于 2017-2-21 22:29

B70还可以。估计后面折腾的人多了，特别是不死UBOOT如果出来了后，就有救了。

75543255 · 发表于 2017-2-22 10:54

ttl连接参数是多少，用的什么工具？？我的一直会有乱码，隐约有一些字符是正确的

xiaojuzi · 发表于 2017-2-22 16:14

75543255 发表于 2017-2-22 10:54
ttl连接参数是多少，用的什么工具？？我的一直会有乱码，隐约有一些字符是正确的

如图

lily339 · 发表于 2017-2-25 21:42

谢谢分享，原厂固件刚开机很快，然后就有点慢了，每天重启没啥用，看op出来以后能不能好点

zsth · 发表于 2017-3-27 19:33

支持研究！！！！！！！

得到的都是侥幸 · 发表于 2020-3-11 12:41

楼主你刷这个固件 20170324-kunteng-ramips-mt7621-nand-hc5962-squashfs-sysupgrade.bin 密码是多少我都进不去

xiaojuzi · 发表于 2020-3-11 23:35

得到的都是侥幸发表于 2020-3-11 12:41
楼主你刷这个固件 20170324-kunteng-ramips-mt7621-nand-hc5962-squashfs-sysupgrade.bin 密码是多少 ...

时间长远密码都忘记了

得到的都是侥幸 · 发表于 2020-3-12 09:05

xiaojuzi 发表于 2020-3-11 23:35
时间长远密码都忘记了

这个帖子还找到的嘛

zc123 · 发表于 2021-1-1 17:36

马克

感谢分享

ljty214 · 发表于 2021-1-26 20:52

有ttl信息又怎么样呢？能ttl刷机吗？

得到的都是侥幸 · 发表于 2021-2-4 16:18

得到的都是侥幸发表于 2020-3-12 09:05
这个帖子还找到的嘛

没找到找了好几个都没找到

账号		自动登录	找回密码
密码			立即注册

现有 B70 极路由 ttl 启动信息发出来。大家一起研究

本帖子中包含更多资源

点评

本帖子中包含更多资源

点评

点评

点评