|
|
本帖最后由 臭臭的包子 于 2017-4-12 09:59 编辑
把开机所有灯微亮成砖的HG255D救回来后，
网页进入192.168.1.1刷固件，重启后再次进入还是刚才的固件恢复界面，纳闷……也就是重启后，固件就没了……
1.TTL连接，secureCRT读取串口数据，显示到这就停下来了
ETH_STATE_ACTIVE!!
[Kernel]Enter Network Loop!
[LED]Thread started!!
2.无意间按了ctrl+C机器接着运行
[Kernel]Abort!
## Booting image at bf080000 ...
Image Name: PandoraBox Linux-3.10.60
Image Type: MIPS Linux Kernel Image (lzma compressed)
Data Size: 1058865 Bytes = 1 MB
Load Address: 80000000
Entry Point: 80000000
Verifying Checksum ... OK
Uncompressing Kernel Image ... OK
No initrd
## Transferring control to Linux (at address 80000000) ...
## Giving linux memsize in MB, 32
Starting kernel ...
PandoraBox For Ralink/MTK APSoC. Copyright 2013-2014 D-Team Technology SZ
LINUX started...
3.机器自检运行了！网页打开192.168.1.1，潘多拉界面可以出来了，但一重启就没了，还是刷机界面……
THIS IS ASIC
[ 0.000000] Linux version 3.10.60 (lintel@PandoraBox-Server) (gcc version 4.8.3 (PandoraBox/Linaro GCC 4.8-2014.04 svn-r208) ) #9 Thu Nov 27 16:25:37 CST 2014
[ 0.000000] CPU Running in Little-Endian Mode !
[ 0.000000] Ralink RT3052 CPU:384MHz, Bus:128MHz Uart:128MHz
[ 0.000000] Boot form:NOR FLASH
[ 0.000000] bootconsole [early0] enabled
[ 0.000000] CPU revision is: 0001964c (MIPS 24KEc)
[ 0.000000] Software DMA cache coherency
[ 0.000000] Determined physical RAM map:
[ 0.000000] memory: 02000000 @ 00000000 (usable)
[ 0.000000] Initrd not found or empty - disabling initrd
[ 0.000000] Zone ranges:
[ 0.000000] Normal [mem 0x00000000-0x01ffffff]
[ 0.000000] Movable zone start for each node
4我去，这是神马情况，原版的机器，硬件我哪里也没动，只是按照lintel大大的方法烙铁焊了个jtag，who 砍 give me a direction？总不能连着TTL线启动机器吧？
uboot和固件版本
http://downloads.openwrt.org.cn/PandoraBox/HuaWei_HG255D/u-boot/ 147K的release版uboot
http://downloads.openwrt.org.cn/PandoraBox/HuaWei_HG255D/firmware/testing/ PandoraBox-ralink-hg255d-r249-20141127.bin固件用的是这个
附：运行LOG（启动日志是很长，但重点地方用红色标记好了，可以慢点翻）
t^Hreboot
PandoraBox login: root
Password:
BusyBox v1.22.1 (2014-11-11 14:07:27 CST) built-in shell (ash)
Enter 'help' for a list of built-in commands.
_______________________________________________________________
| ____ _ ____ |
| | _ \ __ _ _ __ __| | ___ _ __ __ _| __ ) _____ __ |
| | |_) / _` | '_ \ / _` |/ _ \| '__/ _` | _ \ / _ \ \/ / |
| | __/ (_| | | | | (_| | (_) | | | (_| | |_) | (_) > < |
| |_| \__,_|_| |_|\__,_|\___/|_| \__,_|____/ \___/_/\_\ |
| |
| PandoraBox SDK Plantform |
| Copyright 2013-2014 |
| D-Team Technology Co.,Ltd. ShenZhen |
|______________________________________________________________|
Base on OpenWrt BARRIER BREAKER (14.09, r249)
[root@PandoraBox:/root]#reboot
procd: - shutdown -
[root@PandoraBox:/root]#procd: - reboot [ 549.030000] Stopped WatchDog Timer.
-
[ 549.040000] Restarting system.
U-Boot 1.1.3 (Dec 27 2014 - 15:31:12)
SoC:Ralink RT3052
DRAM: Found SDRAM.
TEST-32Bit-0 128M:
CFG0:0xD1825272
CFG1:0xA1220600
CFG2:0x00000000
CFG3:0x00000000
CFG4:0x00000000
TEST-32Bit-1 64M:
CFG0:0xD1825272
CFG1:0xA1120300
CFG2:0x00000000
CFG3:0x00000000
CFG4:0x00000000
TEST-32Bit-2 32M:
CFG0:0xD1825272
CFG1:0xA1110600
CFG2:0x00000000
CFG3:0x00000000
CFG4:0x00000000
Done,SDR is 32 MB
relocate_code Pointer at: 81fa4000
config usb..
******************************
Software System Reset Occurred
******************************
Flash JEDEC Info:
Manufacturer ID:0x00000001
Device ID:0x0000227E
Mode ID:0x00002221
Part ID:0x00002201
FLASH:S29GL128P/N, SIZE:16 MBytes SECTOR:128
S29GLXXX:set sect_size =0x20000
flash_protect ON: from 0xBF000000 to 0xBF024A53
flash_protect ON: from 0xBF040000 to 0xBF040FFF
*** Warning - bad CRC, using default environment
_______________________________________________________________
| ____ _ ____ |
| | _ \ __ _ _ __ __| | ___ _ __ __ _| __ ) _____ __ |
| | |_) / _` | '_ \ / _` |/ _ \| '__/ _` | _ \ / _ \ \/ / |
| | __/ (_| | | | | (_| | (_) | | | (_| | |_) | (_) > < |
| |_| \__,_|_| |_|\__,_|\___/|_| \__,_|____/ \___/_/\_\ |
| |
| PandoraBox Ralink/MTK Platform |
| Copyright 2014 D-Team Technology Co.,Ltd. SZ |
| Board:HuaWei HG255D |
| |
| lintel<lintel.huang@gmail.com> |
|______________________________________________________________|
===============Board Info==================
CPU Frequency:384MHz
Detected Memory:32MiB
Bootloader Version:4.3.0.0
icache: sets:256, ways:4, linesz:32 ,total:32KiB
dcache: sets:128, ways:4, linesz:32 ,total:16KiB
============================================
GSW VLAN:WLLL
GPIO_MODE init:
I2C:GPIO
SPI:GPIO
UART_F:GPIO
GPIO_MODE_REGs: 0x29f
READY_LED_BIT:8.
Please choose the operation:
1: Load system code to SDRAM via TFTP.
2: Load system code then write to Flash via TFTP.
3: Boot system code via Flash (default).
4: Entr boot command line interface.
7: Load Boot Loader code then write to Flash via Serial.
9: Load Boot Loader code then write to Flash via TFTP.
0
3: System Boot system code via Flash.
Press Reset button enter upgrade mode!
WPS button pressed!》》》》》》》》》》》》》》》》》》》》》》》我没有按WPS键，显示我按下了，这可能是DHCP网页刷固件的设置吧
______________________________________________________
| |
| Recovery Module v2.0 |
| |
| Note lease Use Web Browser Upgrade the Firmware ! |
| |
| Copyright 2014 D-Team Technology Co.,Ltd. SZ |
| lintel<lintel.huang@gmail.com> |
|____________________________________________________|
[Kernel]uOS Version: v1.1
[TCP/IP]ETH0 MAC:00:0C:43:30:52:77
[TCP/IP]IP:192.168.1.1
[TCP/IP]Netmask:255.255.255.0
[TCP/IP]Default Router:0.0.0.0
[DHCPD]Server IP:192.168.1.1
NetTxPacket = 0x81FE0100.
Trying Eth0 (10/100-M)
Waitting for RX_DMA_BUSY status Start... done
ETH_STATE_ACTIVE!!
[Kernel]Enter Network Loop!
[LED]Thread started!! 》》》》》》》》》》》》》》》》》》》》卡到这不动了！！！！！！！！！！！！！！！！！！
[DHCPD]Request from MAC:F0 E:F131:B1
[DHCPD]Request from MAC:F0E:F131:B1
[DHCPD]Request from MAC:F0E:F131:B1
[DHCPD][192.168.1.2] -> [F0E:F131:B1]
[DHCPD]Request from MAC:F0E:F131:B1
[Kernel]Abort!》》》》》》》》》》》》》》》》》》》》》》》》》》按CTRL+C后的显示
## Booting image at bf080000 ...
Image Name: PandoraBox Linux-3.10.60
Image Type: MIPS Linux Kernel Image (lzma compressed)
Data Size: 1058865 Bytes = 1 MB
Load Address: 80000000
Entry Point: 80000000
Verifying Checksum ... OK
Uncompressing Kernel Image ... OK
No initrd
## Transferring control to Linux (at address 80000000) ...
## Giving linux memsize in MB, 32
Starting kernel ...
PandoraBox For Ralink/MTK APSoC. Copyright 2013-2014 D-Team Technology SZ
LINUX started...
THIS IS ASIC
[ 0.000000] Linux version 3.10.60 (lintel@PandoraBox-Server) (gcc version 4.8.3 (PandoraBox/Linaro GCC 4.8-2014.04 svn-r208) ) #9 Thu Nov 27 16:25:37 CST 2014
[ 0.000000] CPU Running in Little-Endian Mode !
[ 0.000000] Ralink RT3052 CPU:384MHz, Bus:128MHz Uart:128MHz
[ 0.000000] Boot form:NOR FLASH
[ 0.000000] bootconsole [early0] enabled
[ 0.000000] CPU revision is: 0001964c (MIPS 24KEc)
[ 0.000000] Software DMA cache coherency
[ 0.000000] Determined physical RAM map:
[ 0.000000] memory: 02000000 @ 00000000 (usable)
[ 0.000000] Initrd not found or empty - disabling initrd
[ 0.000000] Zone ranges:
[ 0.000000] Normal [mem 0x00000000-0x01ffffff]
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x00000000-0x01ffffff]
[ 0.000000] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
[ 0.000000] Primary data cache 16kB, 4-way, VIPT, no aliases, linesize 32 bytes
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 8128
[ 0.000000] Kernel command line: console=ttyS1,115200n8 board=HG255D rootfstype=squashfs,jffs2
[ 0.000000] PID hash table entries: 128 (order: -3, 512 bytes)
[ 0.000000] Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.000000] Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.000000] Writing ErrCtl register=00076386
[ 0.000000] Readback ErrCtl register=00076386
[ 0.000000] Memory: 29108k/32768k available (2338k kernel code, 3660k reserved, 552k data, 180k init, 0k highmem)
[ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[ 0.000000] NR_IRQS:128
[ 0.000000] console [ttyS1] enabled, bootconsole disabled
[ 0.000000] console [ttyS1] enabled, bootconsole disabled
[ 0.010000] Calibrating delay loop... 255.59 BogoMIPS (lpj=1277952)
[ 0.090000] pid_max: default: 32768 minimum: 301
[ 0.090000] Mount-cache hash table entries: 512
[ 0.100000] pinctrl core: initialized pinctrl subsystem
[ 0.100000] NET: Registered protocol family 16
[ 0.110000] Ralink/MTK BootROM maped.
[ 0.110000] General GPIO Driver for Ralink RT3052 Board. Copyright lintel 2005-2013
[ 0.120000] RT305X-GPIO0:registering 24 irq handlers
[ 0.120000] RT305X-GPIO1:registering 16 irq handlers
[ 0.130000] RT305X-GPIO2:registering 12 irq handlers
[ 0.130000] MIPS: machine is HuaWei HG255D
[ 0.140000] ralink_register_flash:NOR Flash.
[ 0.140000] Ralink/MTK Pinctrl registered.
[ 0.150000] General PINCRTL Driver for Ralink RT3052 Board. Copyright lintel 2005-2014
[ 0.150000] PINCTRL:add 24 pins for RT305X-PINCTRL0.
[ 0.160000] PINCTRL:add 16 pins for RT305X-PINCTRL1.
[ 0.160000] PINCTRL:add 12 pins for RT305X-PINCTRL2.
[ 0.160000] GPIO_MODE_REG:0x2DF
[ 0.180000] bio: create slab <bio-0> at 0
[ 0.190000] Switching to clocksource MIPS
[ 0.200000] NET: Registered protocol family 2
[ 0.210000] TCP established hash table entries: 512 (order: 0, 4096 bytes)
[ 0.210000] TCP bind hash table entries: 512 (order: -1, 2048 bytes)
[ 0.220000] TCP: Hash tables configured (established 512 bind 512)
[ 0.230000] TCP: reno registered
[ 0.230000] UDP hash table entries: 256 (order: 0, 4096 bytes)
[ 0.240000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[ 0.240000] NET: Registered protocol family 1
[ 0.250000] Ralink SoC clocks api init.
[ 0.250000] mips hpt frequency:192000000HZ
[ 0.260000] Ralink/MTK APSoC GPIO Resource maped.
[ 0.260000] Load Ralink Timer0 Module
[ 0.270000] Load Ralink Timer1 Module
[ 0.270000] Ralink DWC_OTG Host register.
[ 0.310000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.320000] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 0.330000] msgmni has been set to 56
[ 0.340000] io scheduler noop registered
[ 0.340000] io scheduler deadline registered (default)
[ 0.350000] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
[ 0.350000] serial8250: ttyS0 at MMIO 0x10000500 (irq = 37) is a 16550A
[ 0.360000] serial8250: ttyS1 at MMIO 0x10000c00 (irq = 12) is a 16550A
[ 0.370000] Enable Ralink GDMA Controller Module
[ 0.400000] brd: module loaded
[ 0.400000] physmap platform flash device: 01000000 at bf000000
[ 0.410000] physmap-flash: Found 1 x16 devices at 0x0 in 16-bit bank. Manufacturer ID 0x000001 Chip ID 0x002101
[ 0.420000] Amd/Fujitsu Extended Query Table at 0x0040
[ 0.420000] Amd/Fujitsu Extended Query version 1.3.
[ 0.430000] number of CFI chips: 1
[ 0.430000] Creating 5 MTD partitions on "physmap-flash":
[ 0.440000] 0x000000000000-0x000000040000 : "U-Boot"
[ 0.450000] 0x000000040000-0x000000060000 : "U-Boot-Env"
[ 0.450000] 0x000000060000-0x000000080000 : "Factory"
[ 0.460000] 0x000000000000-0x000001000000 : "fullflash"
[ 0.470000] 0x000000080000-0x000001000000 : "firmware"
[ 0.480000] PandoraBox OOPS is ready!
[ 0.480000] 3 uimage-fw partitions found on MTD device firmware
[ 0.490000] 0x000000080000-0x0000001a0000 : "kernel"
[ 0.500000] 0x0000001a0000-0x000000fc0000 : "rootfs"
[ 0.510000] mtd: device 6 (rootfs) set to be root filesystem
[ 0.510000] 1 squashfs-split partitions found on MTD device rootfs
[ 0.520000] 0x000000880000-0x000000fc0000 : "rootfs_data"
[ 0.530000] 0x000000fc0000-0x000001000000 : "panic_oops"
[ 0.530000] mtdoops: Attached to MTD device 8
[ 0.550000] rdm_major = 253
[ 0.550000] EEPROM:Read from [Factory] offset 0x28,length 0x6.
[ 0.560000] warning: ra_mtd_read_nm: rdlen is not equal to len
[ 0.560000] GMAC1_MAC_ADRH -- : 0x0000000c
[ 0.570000] GMAC1_MAC_ADRL -- : 0x43305277
[ 0.570000] Ralink APSoC Ethernet Driver Initilization. v3.1 512 rx/tx descriptors allocated, mtu = 1500!
[ 0.580000] Feature:{HW_CSO} {HW_VLAN_TX} {SKB_RECYCLE_2K}
[ 0.590000] EEPROM:Read from [Factory] offset 0x28,length 0x6.
[ 0.590000] warning: ra_mtd_read_nm: rdlen is not equal to len
[ 0.600000] GMAC1_MAC_ADRH -- : 0x0000000c
[ 0.600000] GMAC1_MAC_ADRL -- : 0x43305277
[ 0.610000] PROC INIT OK!
[ 0.610000] rt305x switch driver registered.
[ 0.620000] TCP: cubic registered
[ 0.620000] NET: Registered protocol family 17
[ 0.620000] 8021q: 802.1Q VLAN Support v1.8
[ 0.630000] PandoraBox Samba accelerater.
[ 0.640000] VFS: Mounted root (squashfs filesystem) readonly on device 31:6.
[ 0.650000] Freeing unused kernel memory: 180K (802d3000 - 80300000)
procd: Console is alive
[ 5.520000] usbcore: registered new interface driver usbfs
[ 5.530000] usbcore: registered new interface driver hub
[ 5.540000] usbcore: registered new device driver usb
[ 5.550000] exFAT: Version 1.2.9
[ 5.630000] ufsd: module license 'Commercial product' taints kernel.
[ 5.630000] Disabling lock debugging due to kernel taint
[ 5.650000] ufsd: driver (8.6, Nov 27 2014 14:11:59, LBD=ON, delalloc, ioctl, bdi) loaded at 80880000
[ 5.650000] NTFS (with native replay) support included
[ 5.650000] optimized: speed
[ 5.650000] Built for PandoraBox 2013-12-27
[ 5.650000]
[ 5.740000] SGI XFS with security attributes, large block/inode numbers, no debug enabled
[ 5.770000] SCSI subsystem initialized
[ 6.640000] dwc2 dwc2.0: DWC OTG Controller
[ 6.640000] dwc2 dwc2.0: new USB bus registered, assigned bus number 1
[ 6.650000] dwc2 dwc2.0: irq 18, io mem 0x00000000
[ 6.650000] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[ 6.660000] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 6.670000] usb usb1: Product: DWC OTG Controller
[ 6.670000] usb usb1: Manufacturer: Linux 3.10.60 dwc2_hsotg
[ 6.680000] usb usb1: SerialNumber: dwc2.0
[ 6.680000] hub 1-0:1.0: USB hub found
[ 6.690000] hub 1-0:1.0: 1 port detected
[ 6.690000] leds-gpio leds-gpio: pins are not configured from the driver
[ 6.710000] usbcore: registered new interface driver usb-storage
procd: - preinit -
Press the [f] key and hit [enter] to enter failsafe mode
Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level
kmod: ran 1 iterations
[ 11.240000] jffs2: notice: (361) jffs2_build_xattr_subsystem: complete building xattr subsystem, 1 of xdatum (0 unchecked, 0 orphan) and 20 of xref (0 dead, 0
orphan) found.
block: extroot: no root or overlay mount defined
jffs2 is ready
jffs2 is ready
[ 11.280000] jffs2: notice: (358) jffs2_build_xattr_subsystem: complete building xattr subsystem, 1 of xdatum (0 unchecked, 0 orphan) and 20 of xref (0 dead, 0
orphan) found.
switching to overlay
procd: - early -
procd: - ubus -
procd: - init -
Please press Enter to activate this console.
[ 16.650000] NET: Registered protocol family 10
[ 16.700000] RPC: Registered named UNIX socket transport module.
[ 16.700000] RPC: Registered udp transport module.
[ 16.710000] RPC: Registered tcp transport module.
[ 16.710000] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 16.790000] tun: Universal TUN/TAP device driver, 1.6
[ 16.790000] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
[ 16.810000] sit: IPv6 over IPv4 tunneling driver
[ 16.830000] gre: GRE over IPv4 demultiplexor driver
[ 16.850000] ip_gre: GRE over IPv4 tunneling driver
[ 17.410000] gpiodev: gpio device registered with major 252
[ 17.440000] nf_conntrack version 0.5.0 (457 buckets, 1828 max)
[ 17.490000] ip6_tables: (C) 2000-2006 Netfilter Core Team
[ 17.520000] Ralink APSoC Hardware Watchdog Timer
[ 17.550000] hidraw: raw HID events driver (C) Jiri Kosina
[ 17.570000] u32 classifier
[ 17.570000] input device check on
[ 17.570000] Actions configured
[ 17.580000] Mirror/redirect action on
[ 17.600000] fuse init (API version 7.22)
[ 18.120000]
[ 18.120000]
[ 18.120000] === pAd = c1770000, size = 1241408 ===
[ 18.120000]
[ 18.130000] <-- RTMPAllocAdapterBlock, Status=0
[ 18.130000] PandoraBox RT2860v2 AP Driver version-3.0.3.2(Nov 27 2014 16:23:52).
[ 18.140000] RT305x_ChipSpecInit: CHIP_SPEC_ID_NUM(3)
[ 18.200000] cm109: Keymap for Komunikate KIP1000 phone loaded
[ 18.220000] usbcore: registered new interface driver cm109
[ 18.220000] cm109: CM109 phone driver: 20080805 (C) Alfred E. Heggestad
[ 18.230000] Loading modules backported from Linux version master-2014-05-22-0-gf2032ea
[ 18.240000] Backport generated by backports.git backports-20140320-37-g5c33da0
[ 18.260000] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 18.360000] usbcore: registered new interface driver usbhid
[ 18.360000] usbhid: USB HID core driver
[ 18.370000] usbcore: registered new interface driver usblp
[ 18.440000] xt_time: kernel timezone is -0000
[ 18.500000] cfg80211: Calling CRDA to update world regulatory domain
[ 18.500000] cfg80211: World regulatory domain updated:
[ 18.510000] cfg80211: DFS Master region: unset
[ 18.510000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time)
[ 18.520000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
[ 18.530000] cfg80211: (2457000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
[ 18.540000] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (N/A, 2000 mBm), (N/A)
[ 18.550000] cfg80211: (5170000 KHz - 5250000 KHz @ 160000 KHz), (N/A, 2000 mBm), (N/A)
[ 18.550000] cfg80211: (5250000 KHz - 5330000 KHz @ 160000 KHz), (N/A, 2000 mBm), (0 s)
[ 18.560000] cfg80211: (5490000 KHz - 5730000 KHz @ 160000 KHz), (N/A, 2000 mBm), (0 s)
[ 18.570000] cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A)
[ 18.580000] cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 0 mBm), (N/A)
[ 18.700000] usbcore: registered new interface driver p54usb
[ 18.720000] PPP generic driver version 2.4.2
[ 18.720000] NET: Registered protocol family 24
[ 18.760000] usbcore: registered new interface driver rt73usb
[ 18.770000] usbcore: registered new interface driver rtl8187
[ 18.800000] usbcore: registered new interface driver snd-usb-audio
[ 18.840000] usbcore: registered new interface driver rt2800usb
[ 27.950000] RtmpOSNetDevDetach(): RtmpOSNetDeviceDetach(), dev->name=ra0!
[ 28.460000]
[ 28.460000]
[ 28.460000] === pAd = c1e3d000, size = 1241408 ===
[ 28.460000]
[ 28.480000] <-- RTMPAllocAdapterBlock, Status=0
[ 28.480000] PandoraBox RT2860v2 AP Driver version-3.0.3.2(Nov 27 2014 16:23:52).
[ 28.490000] RT305x_ChipSpecInit: CHIP_SPEC_ID_NUM(3)
[ 29.480000] RX DESC a0bd3000 size = 2048
[ 29.490000] <-- RTMPAllocTxRxRingMemory, Status=0
[ 30.010000] APSDCapable[0]=0
[ 30.020000] APSDCapable[1]=0
[ 30.020000] APSDCapable[2]=0
[ 30.020000] APSDCapable[3]=0
[ 30.030000] APSDCapable[4]=0
[ 30.030000] APSDCapable[5]=0
[ 30.030000] APSDCapable[6]=0
[ 30.030000] APSDCapable[7]=0
[ 30.040000] APSDCapable[8]=0
[ 30.040000] APSDCapable[9]=0
[ 30.040000] APSDCapable[10]=0
[ 30.050000] APSDCapable[11]=0
[ 30.050000] APSDCapable[12]=0
[ 30.050000] APSDCapable[13]=0
[ 30.060000] APSDCapable[14]=0
[ 30.060000] APSDCapable[15]=0
[ 30.060000] default ApCliAPSDCapable[0]=0
[ 30.360000] Key1Str is Invalid key length(0) or Type(0)
[ 30.360000] Key2Str is Invalid key length(0) or Type(0)
[ 30.370000] Key3Str is Invalid key length(0) or Type(0)
[ 30.370000] Key4Str is Invalid key length(0) or Type(0)
[ 30.450000] 1. Phy Mode = 9
[ 30.460000] 2. Phy Mode = 9
[ 30.460000] EEPROM:Read from [Factory] offset 0x0,length 0x200.
[ 30.460000] warning: ra_mtd_read_nm: rdlen is not equal to len
[ 30.470000] 3. Phy Mode = 9
[ 30.470000] AntCfgInit: primary/secondary ant 0/1
MCS Set = ff ff 00 00 01
[ 30.480000] SYNC - BBP R4 to 20MHz.l
[ 34.260000] PandoraBox Smart Channel Sniffer started.
[ 34.260000] ===============================================================
[ 34.270000] Scanned BSSID list:
[ 34.270000] ch1 bssid:20:f1:7c:6b:28:1c
[ 34.270000] ch1 bssid:00:6b:8e:ac:29:47
[ 34.280000] ch4 bssid:20:f1:7c:6b:28:40
[ 34.280000] ch6 bssid:08:10:78:d7:fe:10
[ 34.290000] ch9 bssid:c8:3a:35:3a:70:28
[ 34.290000] ch11 bssid:20:f1:7c:6a:f4:90
[ 34.290000] ch11 bssid:c8:0e:77:51:93:23
[ 34.300000] ch11 bssid:10:fe:ed:c8:c5:20
[ 34.300000] Channel status:
[ 34.310000] CH1 Dirty:164 CCA:47 Time:8142 Skip:NO
[ 34.310000] CH2 Dirty:112 CCA:47 Time:4234 Skip:NO
[ 34.320000] CH3 Dirty:112 CCA:0 Time:1151 Skip:NO
[ 34.320000] CH4 Dirty:146 CCA:260 Time:44687 Skip:NO
[ 34.330000] CH5 Dirty:124 CCA:131 Time:6025 Skip:NO
[ 34.330000] CH6 Dirty:122 CCA:110 Time:10869 Skip:NO
[ 34.340000] CH7 Dirty:144 CCA:111 Time:17093 Skip:NO
[ 34.340000] CH8 Dirty:152 CCA:2 Time:4558 Skip:NO
[ 34.350000] CH9 Dirty:178 CCA:9 Time:966 Skip:NO
[ 34.350000] CH10 Dirty:148 CCA:55 Time:3614 Skip:NO
[ 34.360000] CH11 Dirty:238 CCA:30 Time:4740 Skip:NO
[ 34.360000] Channel Analysis:
[ 34.360000] Rule 1, CCA value : Min Dirtiness ==> Select Channel 2
[ 34.370000] Min Dirty = 234
[ 34.370000] ExChannel = 6 , 0
[ 34.380000] BW = 40
[ 34.380000] ===============================================================
[ 34.390000] Main bssid = 72:54:99:d1:73:d8
[ 34.390000] <==== rt28xx_init, Status=0
[ 34.450000] 0x1300 = 00064380
[ 35.510000] Raeth v3.1 (Tasklet,SkbRecycle)
[ 35.510000]
[ 35.510000] phy_tx_ring = 0x01da8000, tx_ring = 0xa1da8000
[ 35.520000]
[ 35.520000] phy_rx_ring0 = 0x01daa000, rx_ring0 = 0xa1daa000
[ 35.530000] GMAC1_MAC_ADRH -- : 0x0000000c
[ 35.540000] GMAC1_MAC_ADRL -- : 0x43305277
[ 35.540000] RT305x_ESW: Link Status Changed
[ 35.550000] CDMA_CSG_CFG = 81000007
[ 35.550000] GDMA1_FWD_CFG = 710000
[ 35.590000] device eth0.1 entered promiscuous mode
[ 35.590000] device eth0 entered promiscuous mode
[ 35.620000] br-lan: port 1(eth0.1) entered forwarding state
[ 35.620000] br-lan: port 1(eth0.1) entered forwarding state
[ 37.460000] RT305x_ESW: Link Status Changed
[ 37.620000] br-lan: port 1(eth0.1) entered forwarding state
[ 38.220000] device ra0 entered promiscuous mode
[ 38.230000] br-lan: port 2(ra0) entered forwarding state
[ 38.230000] br-lan: port 2(ra0) entered forwarding state
[ 40.230000] br-lan: port 2(ra0) entered forwarding state
procd: - init complete -》》》》》》》》》》》》》》》》》》》》》》完成，打开192.168.1.1，显示正常了，但一重启就是恢复界面
|
|
简体中文
繁體中文
English
日本語
Deutsch
한국 사람
بالعربية
TÜRKÇE
português
คนไทย
IP卡
狗仔卡
发表于 2017-4-12 00:58
置顶卡
沉默卡
喧嚣卡
顶贴卡
显身卡