AE5000-E2CN2刷Breed或openwrt求助

41257203 · 发表于 2017-5-26 10:56

seague 发表于 2017-5-25 12:14
新进展：
b. wifi power：好像5g和2.4g都只有199mw了，刚开始的那个5g 1000mw的找不到了
c. ap模式可以 ...

功率好像和选择的国家代码以及频段有关，你可以试试选US国家代码试试！

seague · 发表于 2017-5-27 10:54

seague 发表于 2017-5-25 12:14
新进展：
b. wifi power：好像5g和2.4g都只有199mw了，刚开始的那个5g 1000mw的找不到了
c. ap模式可以 ...

经hackpascal 大大提醒，换了breed-qca9558-ar8327n.bin 可以识别128M内存了
“
不能刷dw33d的breed，那个是针对128M*2的内存定制的
另外双flash必须定制，否则都是不支持的
”
16M flash应该也够用了，所以不折腾这个了：）

seague · 发表于 2017-5-27 11:02

本帖最后由 seague 于 2017-5-27 11:12 编辑

seague 发表于 2017-5-27 10:54
经hackpascal 大大提醒，换了breed-qca9558-ar8327n.bin 可以识别128M内存了
“
不能刷dw33d的breed， ...

发射功率问题：
2.4G：选择US, 可以有最大199mw（23db）选项，其他的最大是100mw（20db）
5g：149以上通道可以选择1000mw(30db)，其他的都是199mw（23db）

root@OpenWrt:/# iw list
Wiphy phy1
      max # scan SSIDs: 4
      max scan IEs length: 2257 bytes
      Retry short limit: 7
      Retry long limit: 4
      Coverage class: 0 (up to 0m)
      Device supports AP-side u-APSD.
      Device supports T-DLS.
      Available Antennas: TX 0x3 RX 0x3
      Configured Antennas: TX 0x3 RX 0x3
      Supported interface modes:
               * IBSS
               * managed
               * AP
               * AP/VLAN
               * WDS
               * monitor
               * mesh point
               * P2P-client
               * P2P-GO
      Band 1:
            Capabilities: 0x11ef
                     RX LDPC
                     HT20/HT40
                     SM Power Save disabled
                     RX HT20 SGI
                     RX HT40 SGI
                     TX STBC
                     RX STBC 1-stream
                     Max AMSDU length: 3839 bytes
                     DSSS/CCK HT40
            Maximum RX AMPDU length 65535 bytes (exponent: 0x003)
            Minimum RX AMPDU time spacing: 8 usec (0x06)
            HT TX/RX MCS rate indexes supported: 0-15
            Frequencies:
                     * 2412 MHz [1] (23.0 dBm)
                     * 2417 MHz [2] (23.0 dBm)
                     * 2422 MHz [3] (23.0 dBm)
                     * 2427 MHz [4] (23.0 dBm)
                     * 2432 MHz [5] (23.0 dBm)
                     * 2437 MHz [6] (23.0 dBm)
                     * 2442 MHz [7] (23.0 dBm)
                     * 2447 MHz [8] (23.0 dBm)
                     * 2452 MHz [9] (23.0 dBm)
                     * 2457 MHz [10] (23.0 dBm)
                     * 2462 MHz [11] (23.0 dBm)
                     * 2467 MHz [12] (disabled)
                     * 2472 MHz [13] (disabled)
                     * 2484 MHz [14] (disabled)
      valid interface combinations:
               * #{ managed } <= 2048, #{ AP, mesh point } <= 8, #{ P2P-client, P2P-GO } <= 1, #{ IBSS } <= 1,
               total <= 2048, #channels <= 1, STA/AP BI must match
               * #{ WDS } <= 2048,
               total <= 2048, #channels <= 1, STA/AP BI must match
               * #{ IBSS, AP, mesh point } <= 1,
               total <= 1, #channels <= 1, STA/AP BI must match, radar detect widths: { 20 MHz (no HT), 20 MHz, 40 MHz }

      HT Capability overrides:
               * MCS: ff ff ff ff ff ff ff ff ff ff
               * maximum A-MSDU length
               * supported channel width
               * short GI for 40 MHz
               * max A-MPDU length exponent
               * min MPDU start spacing
Wiphy phy0
      max # scan SSIDs: 16
      max scan IEs length: 199 bytes
      Retry short limit: 7
      Retry long limit: 4
      Coverage class: 0 (up to 0m)
      Device supports AP-side u-APSD.
      Available Antennas: TX 0x3 RX 0x3
      Configured Antennas: TX 0x3 RX 0x3
      Supported interface modes:
               * managed
               * AP
               * AP/VLAN
               * monitor
      Band 2:
            Capabilities: 0x19e3
                     RX LDPC
                     HT20/HT40
                     Static SM Power Save
                     RX HT20 SGI
                     RX HT40 SGI
                     TX STBC
                     RX STBC 1-stream
                     Max AMSDU length: 7935 bytes
                     DSSS/CCK HT40
            Maximum RX AMPDU length 65535 bytes (exponent: 0x003)
            Minimum RX AMPDU time spacing: 8 usec (0x06)
            HT TX/RX MCS rate indexes supported: 0-15
            VHT Capabilities (0x338001b2):
                     Max MPDU length: 11454
                     Supported Channel Width: neither 160 nor 80+80
                     RX LDPC
                     short GI (80 MHz)
                     TX STBC
                     RX antenna pattern consistency
                     TX antenna pattern consistency
            VHT RX MCS set:
                     1 streams: MCS 0-9
                     2 streams: MCS 0-9
                     3 streams: not supported
                     4 streams: not supported
                     5 streams: not supported
                     6 streams: not supported
                     7 streams: not supported
                     8 streams: not supported
            VHT RX highest supported: 0 Mbps
            VHT TX MCS set:
                     1 streams: MCS 0-9
                     2 streams: MCS 0-9
                     3 streams: not supported
                     4 streams: not supported
                     5 streams: not supported
                     6 streams: not supported
                     7 streams: not supported
                     8 streams: not supported
            VHT TX highest supported: 0 Mbps
            Frequencies:
                     * 5180 MHz [36] (23.0 dBm)
                     * 5200 MHz [40] (23.0 dBm)
                     * 5220 MHz [44] (23.0 dBm)
                     * 5240 MHz [48] (23.0 dBm)
                     * 5260 MHz [52] (23.0 dBm) (no IR, radar detection)
                        DFS state: usable (for 86 sec)
                        DFS CAC time: 60000 ms
                     * 5280 MHz [56] (23.0 dBm) (no IR, radar detection)
                        DFS state: usable (for 86 sec)
                        DFS CAC time: 60000 ms
                     * 5300 MHz [60] (23.0 dBm) (no IR, radar detection)
                        DFS state: usable (for 86 sec)
                        DFS CAC time: 60000 ms
                     * 5320 MHz [64] (23.0 dBm) (no IR, radar detection)
                        DFS state: usable (for 86 sec)
                        DFS CAC time: 60000 ms
                     * 5500 MHz [100] (23.0 dBm) (no IR, radar detection)
                        DFS state: usable (for 86 sec)
                        DFS CAC time: 60000 ms
                     * 5520 MHz [104] (23.0 dBm) (no IR, radar detection)
                        DFS state: usable (for 86 sec)
                        DFS CAC time: 60000 ms
                     * 5540 MHz [108] (23.0 dBm) (no IR, radar detection)
                        DFS state: usable (for 86 sec)
                        DFS CAC time: 60000 ms
                     * 5560 MHz [112] (23.0 dBm) (no IR, radar detection)
                        DFS state: usable (for 86 sec)
                        DFS CAC time: 60000 ms
                     * 5580 MHz [116] (23.0 dBm) (no IR, radar detection)
                        DFS state: usable (for 86 sec)
                        DFS CAC time: 60000 ms
                     * 5600 MHz [120] (23.0 dBm) (no IR, radar detection)
                        DFS state: usable (for 86 sec)
                        DFS CAC time: 60000 ms
                     * 5620 MHz [124] (23.0 dBm) (no IR, radar detection)
                        DFS state: usable (for 86 sec)
                        DFS CAC time: 60000 ms
                     * 5640 MHz [128] (23.0 dBm) (no IR, radar detection)
                        DFS state: usable (for 86 sec)
                        DFS CAC time: 60000 ms
                     * 5660 MHz [132] (23.0 dBm) (no IR, radar detection)
                        DFS state: usable (for 86 sec)
                        DFS CAC time: 60000 ms
                     * 5680 MHz [136] (23.0 dBm) (no IR, radar detection)
                        DFS state: usable (for 86 sec)
                        DFS CAC time: 60000 ms
                     * 5700 MHz [140] (23.0 dBm) (no IR, radar detection)
                        DFS state: usable (for 86 sec)
                        DFS CAC time: 60000 ms
                     * 5745 MHz [149] (30.0 dBm)
                     * 5765 MHz [153] (30.0 dBm)
                     * 5785 MHz [157] (30.0 dBm)
                     * 5805 MHz [161] (30.0 dBm)
                     * 5825 MHz [165] (30.0 dBm)
      valid interface combinations:
               * #{ AP } <= 8,
               total <= 8, #channels <= 1, STA/AP BI must match, radar detect widths: { 20 MHz (no HT), 20 MHz, 40 MHz, 80 MHz }

      HT Capability overrides:
               * MCS: ff ff ff ff ff ff ff ff ff ff
               * maximum A-MSDU length
               * supported channel width
               * short GI for 40 MHz
               * max A-MPDU length exponent
               * min MPDU start spacing
root@OpenWrt:/# [ 1086.850000] device wla

seague · 发表于 2017-5-27 11:15

目前是官方标准版的openwrt，未加其它程序，看看是否需要加上adbyby和S-S R

seague · 发表于 2017-5-27 11:47

本帖最后由 seague 于 2017-5-27 11:50 编辑

目前主要问题：
breed-qca9558-ar8327n.bin  GPIO是16，实际reset GPIO是17，导致
1. reset不起作用, 看了下说明，没找到怎么从16改到17的
2. 指示灯没了，breed下面还在闪烁的，进了openwrt就灭了3. USB插拔不起作用
这三个问题是否只能找hackpascal大侠了？
breed> gpio
GPIO direction status  name
0    in       lo
1    in       lo
2    out       lo
3    in       lo
4    out       lo
5    out       hi
6    out       lo
7    out       lo
8    in       lo
9    in       hi
10    out       lo
11    out       lo
12    out       lo    wlan2g
13    in       lo
14    out       hi    sys
15    out       lo    qss
16    in       hi    reset
17    out       hi    wlan5g
18    out       hi    usb1
19    out       hi    usb2
20    in       hi
21    in       lo
22    in       lo
23    in       lo
24    out       lo

41257203 · 发表于 2017-6-4 22:11

我的已经挂了，正准备编程器，结果发现这货有2颗FLASH，这下都不知道刷哪颗了

三胖无线 · 发表于 2017-6-4 22:25

41257203 发表于 2017-6-4 22:11
我的已经挂了，正准备编程器，结果发现这货有2颗FLASH，这下都不知道刷哪颗了

拆掉一个即可，我已经拆了，保留一个即可

seague · 发表于 2017-6-6 08:05

41257203 发表于 2017-6-4 22:11
我的已经挂了，正准备编程器，结果发现这货有2颗FLASH，这下都不知道刷哪颗了

怎么弄的？为撒会挂啊

seague · 发表于 2017-6-6 09:02

41257203 发表于 2017-6-4 22:11
我的已经挂了，正准备编程器，结果发现这货有2颗FLASH，这下都不知道刷哪颗了

没有console刷breed？

41257203 · 发表于 2017-6-6 15:42

seague 发表于 2017-6-6 08:05
怎么弄的？为撒会挂啊

输错指令了，现在已经上编程器了，就是还没焊回去

seague · 发表于 2017-6-6 17:23

41257203 发表于 2017-6-6 15:42
输错指令了，现在已经上编程器了，就是还没焊回去

汗
找到合适好用的固件分享一下

41257203 · 发表于 2017-9-3 12:29

三胖无线发表于 2017-6-4 22:25
拆掉一个即可，我已经拆了，保留一个即可

你好，闲来无事又开始折腾这个路由现在有编程器刷入openwrt焊接回去依然不启动
请教下可以拆掉哪一个

41257203 · 发表于 2017-9-16 22:52

seague 发表于 2017-5-24 12:50
简单刷了一下，步骤如下：
1. 刷breed
如taobao那个哥们提示，刷了大麦dw33的breed，下载地址

你好，能否提供一份这个机器的编程器固件，也就是进入BREED下备份一个，我的用编程器刷入BREED没法启动，估计是引导不了！

jensun · 发表于 2018-2-26 14:57

我昨晚刷了一下 archer c7 v2 DD-WRT 功能正常，不过感觉5.8G的功率很低，墙2墙只有2格了。。。。比K2P 5G要差

jensun · 发表于 2018-2-26 14:57

seague 发表于 2017-5-24 12:50
简单刷了一下，步骤如下：
1. 刷breed
如taobao那个哥们提示，刷了大麦dw33的breed，下载地址

我昨晚刷了一下 archer c7 v2 DD-WRT 功能正常，不过感觉5.8G的功率很低，墙2墙只有2格了。。。。比K2P 5G要差

账号		自动登录	找回密码
密码			立即注册

AE5000-E2CN2刷Breed或openwrt求助

点评

点评

点评

点评

点评