有个问题请教下高手，root密码一直不对怎么办？

甜菜包子

淘了个WNR3000v3，root用户密码不知道，找到论坛里的固件又刷了一遍，然后密码还是不对。就是这个贴https://www.right.com.cn/forum/thread-139515-1-1.html，最后大神建议我ttl读下启动信息，我自己也看不懂，就想着贴到这里，各位高手看看能不能给个建议

U-Boot 1.1.4-g98735ae5 (Mar 24 2011 - 15:19:45)

WNR2000v3 (ar7241) U-boot dni17 V1.3
DRAM:  
sri
ar7240_ddr_initial_config(138): virian ddr1 init
#### TAP VALUE 1 = 0x2, 2 = 0x2 [0xed5c2dd5: 0x5bad59e3]
32 MB
Top of RAM usable for U-Boot at: 82000000
Reserving 283k for U-Boot at: 81fb8000
Reserving 192k for malloc() at: 81f88000
Reserving 44 Bytes for Board Info at: 81f87fd4
Reserving 36 Bytes for Global Data at: 81f87fb0
Reserving 128k for boot params() at: 81f67fb0
Stack Pointer at: 81f67f98
Now running in RAM - U-Boot at: 81fb8000
id read 0x100000ff
sector count = 64
Flash:  4 MB
In:    serial
Out:   serial
Err:   serial
Misc:  force GPIO1 output high
Net:   ag7240_enet_initialize...
Fetching MAC Address from 0x81fea470
Fetching MAC Address from 0x81fea470
Virian MDC CFG Value ==> 4
: cfg1 0xf cfg2 0x7014
eth0: 4c:60:de:dd:86:1d
eth0 up
Virian MDC CFG Value ==> 4
: cfg1 0xf cfg2 0x7214
eth1: 4c:60:de:dd:86:1c
ATHRS26: resetting s26
ATHRS26: s26 reset done
eth1 up
eth0, eth1
Trying eth1
eth1 link down
FAIL
Trying eth0
eth0 link down
FAIL

Client starts...[Listening] for ADVERTISE...TTT
Retry count exceeded; boot the image as usual

nmrp server is stopped or failed !
Hit any key to stop autoboot:  0
   Verifying Checksum ... OK
### SQUASHFS loading 'image/uImage' to 0x80800000
### SQUASHFS load complete: 937475 bytes loaded to 0x80800000
## Booting image at 80800000 ...
   Image Name:   MIPS OpenWrt Linux-3.3.8
   Created:      2014-04-13   3:37:38 UTC
   Image Type:   MIPS Linux Kernel Image (lzma compressed)
   Data Size:    937411 Bytes = 915.4 kB
   Load Address: 80060000
   Entry Point:  80060000
   Verifying Checksum ... OK
   Uncompressing Kernel Image ... OK
No initrd
## Transferring control to Linux (at address 80060000) ...
## Giving linux memsize in bytes, 33554432

Starting kernel ...

[    0.000000] Linux version 3.3.8 (z@z-VirtualBox) (gcc version 4.6.3 20120201 (prerelease) (Linaro GCC 4.6-2012.02) ) #1 Sun Apr 13 11:37:20 CST 2014
[    0.000000] bootconsole [early0] enabled
[    0.000000] CPU revision is: 00019374 (MIPS 24Kc)
[    0.000000] SoC: Atheros AR7241 rev 1
[    0.000000] Clocks: CPU:360.000MHz, DDR:360.000MHz, AHB:180.000MHz, Ref:5.000MHz
[    0.000000] Determined physical RAM map:
[    0.000000]  memory: 02000000 @ 00000000 (usable)
[    0.000000] Initrd not found or empty - disabling initrd
[    0.000000] Zone PFN ranges:
[    0.000000]   Normal   0x00000000 -> 0x00002000
[    0.000000] Movable zone start PFN for each node
[    0.000000] Early memory PFN ranges
[    0.000000]     0: 0x00000000 -> 0x00002000
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 8128
[    0.000000] Kernel command line:  board=WNR2000V3 console=ttyS0,115200 mtdparts=spi0.0:256k(u-boot)ro,64k(u-boot-env)ro,960k(kernel),2752k(rootfs),64k(art)ro,3712k@0x50000(firmware) rootfstype=squashfs,jffs2 noinitrd
[    0.000000] PID hash table entries: 128 (order: -3, 512 bytes)
[    0.000000] Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)
[    0.000000] Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)
[    0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
[    0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
[    0.000000] Writing ErrCtl register=00000000
[    0.000000] Readback ErrCtl register=00000000
[    0.000000] Memory: 29088k/32768k available (2139k kernel code, 3680k reserved, 407k data, 212k init, 0k highmem)
[    0.000000] SLUB: Genslabs=9, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[    0.000000] NR_IRQS:51
[    0.000000] Calibrating delay loop... 239.61 BogoMIPS (lpj=1198080)
[    0.070000] pid_max: default: 32768 minimum: 301
[    0.070000] Mount-cache hash table entries: 512
[    0.080000] NET: Registered protocol family 16
[    0.080000] gpiochip_add: registered GPIOs 0 to 17 on device: ath79
[    0.090000] MIPS: machine is NETGEAR WNR2000 V3
[    0.520000] registering PCI controller with io_map_base unset
[    0.530000] bio: create slab <bio-0> at 0
[    0.540000] PCI host bridge to bus 0000:00
[    0.540000] pci_bus 0000:00: root bus resource [mem 0x10000000-0x13ffffff]
[    0.550000] pci_bus 0000:00: root bus resource [io  0x0000]
[    0.550000] pci 0000:00:00.0: fixup device configuration
[    0.560000] pci 0000:00:00.0: BAR 0: assigned [mem 0x10000000-0x1000ffff 64bit]
[    0.560000] pci 0000:00:00.0: using irq 40 for pin 1
[    0.570000] Switching to clocksource MIPS
[    0.570000] NET: Registered protocol family 2
[    0.580000] IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.580000] TCP established hash table entries: 1024 (order: 1, 8192 bytes)
[    0.590000] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
[    0.590000] TCP: Hash tables configured (established 1024 bind 1024)
[    0.600000] TCP reno registered
[    0.600000] UDP hash table entries: 256 (order: 0, 4096 bytes)
[    0.610000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[    0.620000] NET: Registered protocol family 1
[    0.640000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    0.650000] JFFS2 version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[    0.660000] msgmni has been set to 56
[    0.660000] io scheduler noop registered
[    0.670000] io scheduler deadline registered (default)
[    0.670000] Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled
[    0.700000] serial8250.0: ttyS0 at MMIO 0x18020000 (irq = 11) is a 16550A
[    0.710000] console [ttyS0] enabled, bootconsole disabled
[    0.710000] console [ttyS0] enabled, bootconsole disabled
[    0.720000] m25p80 spi0.0: found mx25l3205d, expected m25p80
[    0.730000] m25p80 spi0.0: mx25l3205d (4096 Kbytes)
[    0.730000] 6 cmdlinepart partitions found on MTD device spi0.0
[    0.740000] Creating 6 MTD partitions on "spi0.0":
[    0.740000] 0x000000000000-0x000000040000 : "u-boot"
[    0.750000] 0x000000040000-0x000000050000 : "u-boot-env"
[    0.760000] 0x000000050000-0x000000140000 : "kernel"
[    0.760000] 0x000000140000-0x0000003f0000 : "rootfs"
[    0.770000] mtd: partition "rootfs" set to be root filesystem
[    0.780000] mtd: partition "rootfs_data" created automatically, ofs=390000, len=60000
[    0.780000] 0x000000390000-0x0000003f0000 : "rootfs_data"
[    0.790000] 0x0000003f0000-0x000000400000 : "art"
[    0.800000] 0x000000050000-0x0000003f0000 : "firmware"
[    0.830000] ag71xx_mdio: probed
[    0.830000] eth0: Atheros AG71xx at 0xb9000000, irq 4
[    1.390000] ag71xx ag71xx.0: eth0: connected to PHY at ag71xx-mdio.1:04 [uid=004dd041, driver=Generic PHY]
[    1.400000] eth1: Atheros AG71xx at 0xba000000, irq 5
[    1.950000] eth1: Found an AR7240/AR9330 built-in switch
[    2.990000] TCP cubic registered
[    2.990000] NET: Registered protocol family 17
[    2.990000] Bridge firewalling registered
[    3.000000] 8021q: 802.1Q VLAN Support v1.8
[    3.010000] VFS: Mounted root (squashfs filesystem) readonly on device 31:3.
[    3.020000] Freeing unused kernel memory: 212k freed
- preinit -
Press the [f] key and hit [enter] to enter failsafe mode
- regular preinit -
[    7.840000] JFFS2 notice: (418) jffs2_build_xattr_subsystem: complete building xattr subsystem, 1 of xdatum (1 unchecked, 0 orphan) and 65 of xref (0 dead, 52 orphan) found.
switching to jffs2
- init -

Please press Enter to activate this console. [   10.030000] Loading modules backported from Linux version master-2014-01-23-0-g62c147d
[   10.040000] Backport generated by backports.git backports-20140124-0-g1256d3e
[   10.230000] cfg80211: Calling CRDA to update world regulatory domain
[   10.240000] cfg80211: World regulatory domain updated:
[   10.240000] cfg80211:  DFS Master region: unset
[   10.250000] cfg80211:   (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[   10.260000] cfg80211:   (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[   10.260000] cfg80211:   (2457000 KHz - 2482000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[   10.270000] cfg80211:   (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[   10.280000] cfg80211:   (5170000 KHz - 5250000 KHz @ 80000 KHz), (300 mBi, 2000 mBm)
[   10.290000] cfg80211:   (5735000 KHz - 5835000 KHz @ 80000 KHz), (300 mBi, 2000 mBm)
[   10.290000] cfg80211:   (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 0 mBm)
[   11.280000] PCI: Enabling device 0000:00:00.0 (0000 -> 0002)
[   11.290000] ath: phy0: eeprom contains invalid mac address: ff:ff:ff:ff:ff:ff
[   11.300000] ath: phy0: random mac address will be used: 8e:ed:45:99:8f:43
[   11.330000] ieee80211 phy0: Atheros AR9287 Rev:2 mem=0xb0000000, irq=40
[   11.340000] cfg80211: Calling CRDA for country: US
[   11.340000] cfg80211: Regulatory domain changed to country: US
[   11.350000] cfg80211:  DFS Master region: FCC
[   11.350000] cfg80211:   (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[   11.360000] cfg80211:   (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2700 mBm)
[   11.370000] cfg80211:   (5170000 KHz - 5250000 KHz @ 80000 KHz), (300 mBi, 1700 mBm)
[   11.380000] cfg80211:   (5250000 KHz - 5330000 KHz @ 80000 KHz), (300 mBi, 2400 mBm)
[   11.380000] cfg80211:   (5490000 KHz - 5600000 KHz @ 80000 KHz), (300 mBi, 2400 mBm)
[   11.390000] cfg80211:   (5650000 KHz - 5710000 KHz @ 40000 KHz), (300 mBi, 2400 mBm)
[   11.400000] cfg80211:   (5735000 KHz - 5835000 KHz @ 80000 KHz), (300 mBi, 3000 mBm)
[   11.410000] cfg80211:   (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 4000 mBm)
[   11.480000] PPP generic driver version 2.4.2
[   11.660000] tun: Universal TUN/TAP device driver, 1.6
[   11.670000] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
[   11.780000] GRE over IPv4 demultiplexor driver
[   11.810000] GRE over IPv4 tunneling driver
[   12.020000] ip_tables: (C) 2000-2006 Netfilter Core Team
[   12.200000] NET: Registered protocol family 24
[   12.320000] nf_conntrack version 0.5.0 (457 buckets, 1828 max)
[   12.670000] p p t p driver version 0.8.5
[   13.470000] xt_time: kernel timezone is -0000
[   14.140000]  Hooked IMQ after mangle on PREROUTING
[   14.150000]  Hooked IMQ after nat on POSTROUTING
[   14.150000] IMQ driver loaded successfully. (numdevs = 2, numqueues = 1)
[   14.300000] Ebtables v2.0 registered
[   30.470000] device eth1 entered promiscuous mode
Sep 16 20:10:01 crond[944]: user root: parse error at etc

Sep 16 20:10:01 crond[944]: user root: parse error at lib

^C
Please press Enter to activate this console. Sep 16 20:40:01 crond[944]: user root: parse error at etc

Sep 16 20:40:01 crond[944]: user root: parse error at lib

99010

http://downloads.openwrt.org/bar ... quashfs-factory.img

qfnuzlr

密码不对 真没办法 重刷个固件