OpenWrt/LEDE 4M精简迷你固件-Luci界面-SFE加速-SQM分配-UPNP-IPv6-VLAN支持-WIFI计划

阿*** · 发表于 2018-6-23 13:46

非常给力，准备试试

tzw*** · 发表于 2018-6-24 17:45

本帖最后由 tzwjkl 于 2018-6-24 17:50 编辑

大神，请教一下。我的840N V2在原厂固件的软件升级里通过TFTPD升级会报错，请问该怎么做才能刷第三方固件？要硬改吗？

附路由器图，网上查了wr840n有几个外观的...但是我的拆开和
http://forum.anywlan.com/thread-268174-1-1.html
里的v2是一样的，应该是WR840N V2没错吧？

zhz*** · 发表于 2018-6-24 23:51

我现在就用LEDE 17.0.1.0.4

zhz*** · 发表于 2018-6-25 00:55

刚刚刷了，但没有软件包选项。

程式*** · 发表于 2018-6-25 14:42

请教H大的941 V7代码，也遇上了无限重启情况，后面是怎么解决的，问题在哪？非常感谢！

程式*** · 发表于 2018-6-25 19:46

AndyX 发表于 2018-1-31 02:05
正在找问题，你可以先尝试用881N V1代替一下，除了LED有些不正常之外其他都好。

老大，找到问题了吗？我这用H大代码遇上同样问题，无限重启，请赐教，谢谢！

程式*** · 发表于 2018-6-26 10:22

Boot and Recovery Environment for Embedded Devices
Copyright (C) 2018 HackPascal <hackpascal@gmail.com>
Build date 2018-06-12 [git-b25d73d]
Version 1.1 (r1220)

DRAM: 64MB
Platform: Qualcomm Atheros QCA9558 rev 0
Board: TP-LINK TL-WR2041N v2
Clocks: CPU: 720MHz, DDR: 400MHz, AHB: 200MHz, Ref: 40MHz
Flash: Winbond W25Q64 (8MB) on ath79-spi
ag71xx-eth: Using MAC address 9c:21:6a:2a:2a:dc
Waiting for auto-negotiation complete ... Timed out
eth0: Atheros AR8236 rev 1

Network started on eth0, inet addr 192.168.1.1, netmask 255.255.255.0

Press any key to interrupt autoboot ... 0

Trying to boot firmware from 0x9f020000 ...
TP-LINK firmware image header detected.
Image Name: 09410007
Data Size: 1301958 Bytes
Load Address: 80060000
Entry Point:  80060000
Uncompressing data (LZMA) ... done.
Flushing cache ... done.

Starting kernel at 0x80060000...

[ 0.000000] Linux version 4.9.107 (user@user-virtual-machine) (gcc version 7.3.0 (OpenWrt GCC 7.3.0 r493-4785e97) ) #0 Sun Jun 17 04:45:06 2018
[ 0.000000] bootconsole [early0] enabled
[ 0.000000] CPU0 revision is: 00019750 (MIPS 74Kc)
[ 0.000000] SoC: Qualcomm Atheros QCA9558 ver 1 rev 0
[ 0.000000] Determined physical RAM map:
[ 0.000000]  memory: 04000000 @ 00000000 (usable)
[ 0.000000] Initrd not found or empty - disabling initrd
[ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
[ 0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
[ 0.000000] Zone ranges:
[ 0.000000] Normal [mem 0x0000000000000000-0x0000000003ffffff]
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x0000000000000000-0x0000000003ffffff]
[ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x0000000003ffffff]
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 16256
[ 0.000000] Kernel command line:  board=TL-WR941N-v7  console=ttyS0,115200 rootfstype=squashfs noinitrd
[ 0.000000] MIPS: no machine found for id 'TL-WR941N-v7', supported machines:
[ 0.000000] id                      name
[ 0.000000] Generic                Generic AR71XX/AR724X/AR913X based board
[ 0.000000] DIR-615-E4             D-Link DIR-615 rev. E4
[ 0.000000] DIR-615-E1             D-Link DIR-615 rev. E1
[ 0.000000] EBR-2310-C1             D-Link EBR-2310 rev. C1
[ 0.000000] DIR-600-A1             D-Link DIR-600 rev. A1
[ 0.000000] DIR-615-C1             D-Link DIR-615 rev. C1
[ 0.000000] DIR-615-I1             D-Link DIR-615 rev. I1
[ 0.000000] NBG460N                Zyxel NBG460N/550N/550NH
[ 0.000000] TEW-632BRP             TRENDnet TEW-632BRP
[ 0.000000] TEW-712BR             TRENDnet TEW-712BR
[ 0.000000] TL-MR3040-v2          TP-LINK TL-MR3040 v2
[ 0.000000] TL-MR3040             TP-LINK TL-MR3040
[ 0.000000] TL-MR11U                TP-LINK TL-MR11U
[ 0.000000] TL-MR13U                TP-LINK TL-MR13U v1
[ 0.000000] TL-MR3020             TP-LINK TL-MR3020
[ 0.000000] TL-WR841N-v7          TP-LINK TL-WR841N/ND v7
[ 0.000000] TL-MR3420             TP-LINK TL-MR3420
[ 0.000000] TL-MR3220             TP-LINK TL-MR3220
[ 0.000000] TL-WA701ND-v2          TP-LINK TL-WA701ND v2
[ 0.000000] TL-WA7210N-v2          TP-LINK TL-WA7210N v2
[ 0.000000] TL-WA801ND-v3          TP-LINK TL-WA801ND v3
[ 0.000000] TL-WA830RE-v2          TP-LINK TL-WA830RE v2
[ 0.000000] TL-WA901ND-v3          TP-LINK TL-WA901ND v3
[ 0.000000] TL-WA860RE             TP-LINK TL-WA860RE
[ 0.000000] TL-WA855RE-v1          TP-LINK TL-WA855RE v1
[ 0.000000] TL-WA850RE-V2          TP-LINK TL-WA850RE v2
[ 0.000000] TL-WA850RE             TP-LINK TL-WA850RE
[ 0.000000] TL-WA801ND-v2          TP-LINK TL-WA801ND v2
[ 0.000000] TL-WA750RE             TP-LINK TL-WA750RE
[ 0.000000] TL-WA7510N             TP-LINK TL-WA7510N v1
[ 0.000000] TL-WA901ND             TP-LINK TL-WA901ND
[ 0.000000] TL-WA901ND-v2          TP-LINK TL-WA901ND v2
[ 0.000000] TL-WA901ND-v5          TP-LINK TL-WA901ND v5
[ 0.000000] TL-WA901ND-v4          TP-LINK TL-WA901ND v4
[ 0.000000] TL-WDR3320-v2          TP-LINK TL-WDR3320 v2
[ 0.000000] TL-WDR3500             TP-LINK TL-WDR3500
[ 0.000000] TL-WR1041N-v2          TP-LINK TL-WR1041N v2
[ 0.000000] TL-WR710N             TP-LINK TL-WR710N v1
[ 0.000000] TL-WR703N             TP-LINK TL-WR703N v1
[ 0.000000] TL-MR10U                TP-LINK TL-MR10U
[ 0.000000] TL-WR720N-v3          TP-LINK TL-WR720N v3/v4
[ 0.000000] TL-WR741ND             TP-LINK TL-WR741ND
[ 0.000000] TL-MR3220-v2          TP-LINK TL-MR3220 v2
[ 0.000000] TL-WR741ND-v4          TP-LINK TL-WR741ND v4
[ 0.000000] TL-WR802N-v2          TP-LINK TL-WR802N v2
[ 0.000000] TL-WR802N-v1          TP-LINK TL-WR802N v1
[ 0.000000] TL-WR740N-v6          TP-LINK TL-WR740N/ND v6
[ 0.000000] TL-WR842N-v3          TP-LINK TL-WR842N/ND v3
[ 0.000000] TL-WR841N-v11          TP-LINK TL-WR841N/ND v11
[ 0.000000] TL-WR841N-v9          TP-LINK TL-WR841N/ND v9
[ 0.000000] TL-WR840N-v3          TP-LINK TL-WR840N v3
[ 0.000000] TL-WR840N-v2          TP-LINK TL-WR840N v2
[ 0.000000] TL-WR841N-v1.5          TP-LINK TL-WR841N v1
[ 0.000000] TL-WR941ND-v5          TP-LINK TL-WR941N/ND v5
[ 0.000000] TL-MR3420-v2          TP-LINK TL-MR3420 v2
[ 0.000000] TL-WR842N-v2          TP-LINK TL-WR842N/ND v2
[ 0.000000] TL-WR841N-v8          TP-LINK TL-WR841N/ND v8
[ 0.000000] TL-WR941ND             TP-LINK TL-WR941ND
[ 0.000000] TL-WR941ND-v6          TP-LINK TL-WR941N/ND v6
[ 0.000000] TL-WR940N-v6          TP-LINK TL-WR940N v6
[ 0.000000] TL-WR940N-v4          TP-LINK TL-WR940N v4
[ 0.000000] WHR-HP-GN             Buffalo WHR-HP-GN
[ 0.000000] WHR-G301N             Buffalo WHR-G301N
[ 0.000000] WHR-HP-G300N          Buffalo WHR-HP-G300N
[ 0.000000] WLAE-AG300N             Buffalo WLAE-AG300N
[ 0.000000] WNR2000                NETGEAR WNR2000
[ 0.000000] WPN824N                NETGEAR WPN824N
[ 0.000000] WNR1000V2             NETGEAR WNR1000 V2
[ 0.000000] WNR612V2                NETGEAR WNR612 V2
[ 0.000000] WNR2000V3             NETGEAR WNR2000 V3
[ 0.000000] WNR2000V4             NETGEAR WNR2000 V4
[ 0.000000] WP543                   Compex WP543
[ 0.000000] WPE72                   Compex WPE72
[ 0.000000] PID hash table entries: 256 (order: -2, 1024 bytes)
[ 0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
[ 0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.000000] Writing ErrCtl register=00000000
[ 0.000000] Readback ErrCtl register=00000000
[ 0.000000] Memory: 60280K/65536K available (3236K kernel code, 155K rwdata, 408K rodata, 224K init, 213K bss, 5256K reserved, 0K cma-reserved)
[ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[ 0.000000] NR_IRQS:51
[ 0.000000] Clocks: CPU:720.000MHz, DDR:400.000MHz, AHB:200.000MHz, Ref:40.000MHz
[ 0.000000] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 5309056796 ns
[ 0.000008] sched_clock: 32 bits at 360MHz, resolution 2ns, wraps every 5965232126ns
[ 0.008709] Calibrating delay loop... 358.80 BogoMIPS (lpj=1794048)
[ 0.071734] pid_max: default: 32768 minimum: 301
[ 0.076982] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.084362] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.094807] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[ 0.105805] futex hash table entries: 256 (order: -1, 3072 bytes)
[ 0.113190] NET: Registered protocol family 16
[ 0.119625] MIPS: machine is Generic AR71XX/AR724X/AR913X based board
[ 0.126809] Can't analyze schedule() prologue at 80385a24
[ 0.145173] clocksource: Switched to clocksource MIPS
[ 0.151858] NET: Registered protocol family 2
[ 0.157703] TCP established hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.165541] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.172639] TCP: Hash tables configured (established 1024 bind 1024)
[ 0.179839] UDP hash table entries: 256 (order: 0, 4096 bytes)
[ 0.186401] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[ 0.193660] NET: Registered protocol family 1
[ 0.202648] Crashlog allocated RAM at address 0x3f00000
[ 0.209498] workingset: timestamp_bits=30 max_order=14 bucket_order=0
[ 0.223182] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.229732] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 0.249454] io scheduler noop registered
[ 0.253825] io scheduler deadline registered (default)
[ 0.259954] Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled
[ 0.267483] console [ttyS0] disabled
[ 0.291566] serial8250.0: ttyS0 at MMIO 0x18020000 (irq = 11, base_baud = 2500000) is a 16550A
[ 0.301201] console [ttyS0] enabled
[ 0.301201] console [ttyS0] enabled
[ 0.308619] bootconsole [early0] disabled
[ 0.308619] bootconsole [early0] disabled
[ 0.318751] libphy: Fixed MDIO Bus: probed
[ 0.326152] NET: Registered protocol family 10
[ 0.340980] NET: Registered protocol family 17
[ 0.345724] 8021q: 802.1Q VLAN Support v1.8
[ 0.352257] VFS: Cannot open root device "(null)" or unknown-block(0,0): error -6
[ 0.359904] Please append a correct "root=" boot option; here are the available partitions:
[ 0.368386] Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(0,0)
[ 0.377795] Rebooting in 1 seconds..

Boot and Recovery Environment for Embedded Devices
Copyright (C) 2018 HackPascal <hackpascal@gmail.com>
Build date 2018-06-12 [git-b25d73d]
Version 1.1 (r1220)

DRAM: 64MB
Platform: Qualcomm Atheros QCA9558 rev 0
Board: TP-LINK TL-WR2041N v2
Clocks: CPU: 720MHz, DDR: 400MHz, AHB: 200MHz, Ref: 40MHz
Flash: Winbond W25Q64 (8MB) on ath79-spi
ag71xx-eth: Using MAC address 9c:21:6a:2a:2a:dc
Waiting for auto-negotiation complete ... Timed out
eth0: Atheros AR8236 rev 1

Network started on eth0, inet addr 192.168.1.1, netmask 255.255.255.0

Press any key to interrupt autoboot ... 0

Trying to boot firmware from 0x9f020000 ...
TP-LINK firmware image header detected.
Image Name: 09410007
Data Size: 1301958 Bytes
Load Address: 80060000
Entry Point:  80060000
Uncompressing data (LZMA) ... done.
Flushing cache ... done.

Starting kernel at 0x80060000...
循环。。。无限重启。。。

这个是分区地址有问题吗？只补了H大代码，其他都没改

wangh*** · 发表于 2018-6-26 14:06

能否加入去广告插件？adbyby

Abas*** · 发表于 2018-6-27 07:35

想请问楼主能不能发一下CONFIG文件呢

zhz*** · 发表于 2018-6-29 19:24

谢谢楼主分享！

zhz*** · 发表于 2018-6-30 23:30

楼主你这固件能支持一线多拔吗？

wangh*** · 发表于 2018-8-5 16:34

有7620的固件吗？

mor*** · 发表于 2018-10-5 13:59

跟着楼主学习一下试试

parke*** · 发表于 2018-10-5 17:16

请问一下大神NETGEAR WNR2000 v4 支持嘛谢谢！感谢！

WILS*** · 发表于 2018-11-6 12:40

请问刷这个，可以实现S-S R兲朝上网吗？

账号		自动登录	找回密码
密码			立即注册

OpenWrt/LEDE 4M精简迷你固件-Luci界面-SFE加速-SQM分配-UPNP-IPv6-VLAN支持-WIFI计划

本帖子中包含更多资源