华为hg622 无线（未关联）求助！

xuhui0607

华为ＨＧ622

启动信息：

Flash boot Flag: MAINSS
Boot from main system!
LZMA: Prossible old LZMA format, trying to decompress..
Decompression OK!
Entry at 0x80a00000
Closing network.
Disabling Switch ports.
Flushing Receive Buffers...
54 buffers found.
Closing DMA Channels.
Starting program at 0x80a00000
[    0.000000] Linux version 4.9.120 (buildbot@builds-03.infra.lede-project.org) (gcc version 7.3.0 (OpenWrt GCC 7.3.0 r7102-3f3a2c9) ) #0 Wed Aug 15 20:42:39 2018
[    0.000000] Detected Broadcom 0x6368 CPU revision b2
[    0.000000] CPU frequency is 400 MHz
[    0.000000] 32MB of RAM installed
[    0.000000] board_bcm963xx: Boot address 0xb8000000
[    0.000000] board_bcm963xx: CFE version: 1.0.37-102.6
[    0.000000] bootconsole [early0] enabled
[    0.000000] CPU0 revision is: 0002a031 (Broadcom BMIPS4350)
[    0.000000] board: board name: 96368MVWG_hg622
[    0.000000] MIPS: machine is Huawei HG622
[    0.000000] Determined physical RAM map:
[    0.000000]  memory: 02000000 @ 00000000 (usable)
[    0.000000] Initrd not found or empty - disabling initrd
[    0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 16 bytes.
[    0.000000] Primary data cache 32kB, 2-way, VIPT, cache aliases, linesize 16 bytes
[    0.000000] Zone ranges:
[    0.000000]   Normal   [mem 0x0000000000000000-0x0000000001ffffff]
[    0.000000] Movable zone start for each node
[    0.000000] Early memory node ranges
[    0.000000]   node   0: [mem 0x0000000000000000-0x0000000001ffffff]
[    0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x0000000001ffffff]
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 8128
[    0.000000] Kernel command line: rootfstype=squashfs,jffs2 noinitrd console=ttyS0,115200
[    0.000000] PID hash table entries: 128 (order: -3, 512 bytes)
[    0.000000] Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)
[    0.000000] Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)
[    0.000000] Memory: 26608K/32768K available (3484K kernel code, 180K rwdata, 576K rodata, 1256K init, 217K bss, 6160K reserved, 0K cma-reserved)
[    0.000000] SLUB: HWalign=16, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[    0.000000] NR_IRQS:256
[    0.000000] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 9556302233 ns
[    0.000015] sched_clock: 32 bits at 200MHz, resolution 5ns, wraps every 10737418237ns
[    0.008103] Calibrating delay loop... 397.82 BogoMIPS (lpj=795648)
[    0.042733] pid_max: default: 32768 minimum: 301
[    0.047683] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.054445] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.070284] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns
[    0.080318] futex hash table entries: 256 (order: -1, 3072 bytes)
[    0.086679] pinctrl core: initialized pinctrl subsystem
[    0.094447] NET: Registered protocol family 16
[    0.102823] Can't analyze schedule() prologue at 80373764
[    0.108451] registering PCI controller with io_map_base unset
[    0.114319] registering PCI controller with io_map_base unset
[    0.146869] PCI host bridge to bus 0000:00
[    0.151105] pci_bus 0000:00: root bus resource [mem 0x30000000-0x37ffffff]
[    0.158142] pci_bus 0000:00: root bus resource [io  0x8000000-0x8007fff]
[    0.165038] pci_bus 0000:00: root bus resource [??? 0x00000000 flags 0x0]
[    0.172027] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]
[    0.188486] pci 0000:00:01.0: BAR 0: assigned [mem 0x30000000-0x3000ffff]
[    0.196161] PCI host bridge to bus 0000:01
[    0.200351] pci_bus 0000:01: root bus resource [mem 0x38000000-0x3fffffff]
[    0.207411] pci_bus 0000:01: root bus resource [io  0x8008000-0x800ffff]
[    0.214310] pci_bus 0000:01: root bus resource [??? 0x00000000 flags 0x0]
[    0.221297] pci_bus 0000:01: No busn resource found for root bus, will use [bus 01-ff]
[    0.229842] pci 0000:01:1e.0: bridge configuration invalid ([bus 00-00]), reconfiguring
[    0.238327] pci 0000:01:1e.0: BAR 10: assigned [mem 0x38000000-0x3fffffff]
[    0.245387] pci 0000:01:1e.0: BAR 7: assigned [io  0x8008000-0x80080ff]
[    0.252178] pci 0000:01:1e.0: BAR 8: assigned [io  0x8008400-0x80084ff]
[    0.258986] pci 0000:01:1e.0: CardBus bridge to [bus 02-05]
[    0.264718] pci 0000:01:1e.0:   bridge window [io  0x8008000-0x80080ff]
[    0.271527] pci 0000:01:1e.0:   bridge window [io  0x8008400-0x80084ff]
[    0.278336] pci 0000:01:1e.0:   bridge window [mem 0x38000000-0x3fffffff]
[    0.292011] clocksource: Switched to clocksource MIPS
[    0.299383] NET: Registered protocol family 2
[    0.305520] TCP established hash table entries: 1024 (order: 0, 4096 bytes)
[    0.312762] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
[    0.319312] TCP: Hash tables configured (established 1024 bind 1024)
[    0.326211] UDP hash table entries: 256 (order: 0, 4096 bytes)
[    0.332267] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[    0.339113] NET: Registered protocol family 1
[    0.350161] Crashlog allocated RAM at address 0x1f00000
[    0.357969] workingset: timestamp_bits=30 max_order=13 bucket_order=0
[    0.377516] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    0.383517] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[    0.414346] io scheduler noop registered
[    0.418385] io scheduler deadline registered (default)
[    0.426268] bcm6368-pinctrl 10000080.pin-controller: registered at mmio b0000080
▒[    0.444652] console [ttyS0] enabledt MMIO 0x10000100 (irq = 10, base_baud = 1562500) is a bcm63xx_uart
[    0.444652] console [ttyS0] enabled
[    0.451775] bootconsole [early0] disabled
[    0.451775] bootconsole [early0] disabled
[    0.460737] bcm63xx-rng bcm63xx-rng: registered RNG driver
[    0.467397] 18000000.nor: Found 1 x16 devices at 0x0 in 16-bit bank. Manufacturer ID 0x0000c2 Chip ID 0x00227e
[    0.477740] Amd/Fujitsu Extended Query Table at 0x0040
[    0.483003]   Amd/Fujitsu Extended Query version 1.3.
[    0.488181] number of CFI chips: 1
[    0.499913] bcm63xxpart: Partition 0 is CFE offset 0 and length 20000
[    0.506544] bcm63xxpart: Partition 1 is nvram offset fe0000 and length 20000
[    0.513759] bcm63xxpart: Partition 2 is linux offset 20000 and length fc0000
[    0.521078] 3 bcm63xxpart partitions found on MTD device 18000000.nor
[    0.527684] Creating 3 MTD partitions on "18000000.nor":
[    0.533142] 0x000000000000-0x000000020000 : "CFE"
[    0.540534] 0x000000fe0000-0x000001000000 : "nvram"
[    0.548650] 0x000000020000-0x000000fe0000 : "linux"
[    0.557415] parser_imagetag: rootfs: CFE image tag found at 0x0 with version 7, board type 96368MVWG_hg622
[    0.567379] parser_imagetag: Partition 0 is kernel offset 100 and length 15b3f8
[    0.574860] parser_imagetag: Partition 1 is rootfs offset 15b4f8 and length e64b08
[    0.582651] parser_imagetag: Spare partition is offset 3a0004 and length c1fffc
[    0.590238] 2 bcm963xx-imagetag partitions found on MTD device linux
[    0.596759] Creating 2 MTD partitions on "linux":
[    0.601589] 0x000000000100-0x00000015b4f8 : "kernel"
[    0.609478] 0x00000015b4f8-0x000000fc0000 : "rootfs"
[    0.617701] mtd: device 4 (rootfs) set to be root filesystem
[    0.623562] 1 squashfs-split partitions found on MTD device rootfs
[    0.629887] 0x0000003a0000-0x000000fc0000 : "rootfs_data"
[    0.641363] bcm63xx-spi 10000800.spi: at [mem 0x10000800-0x10000f0b flags 0x200] (irq 9, FIFOs size 542)
[    0.652794] libphy: Fixed MDIO Bus: probed
[    0.700780] b53_common: found switch: BCM63xx, rev 0
[    0.706264] bcm63xx-wdt bcm63xx-wdt:  started, timer margin: 30 sec
[    0.715634] NET: Registered protocol family 10
[    0.728697] NET: Registered protocol family 17
[    0.733333] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this.
[    0.746649] 8021q: 802.1Q VLAN Support v1.8
[    0.760618] VFS: Mounted root (squashfs filesystem) readonly on device 31:4.
[    0.781592] Freeing unused kernel memory: 1256K
[    0.786234] This architecture does not have kernel memory protection.
[    1.240024] random: fast init done
[    1.572348] init: Console is alive
[    1.576078] init: - watchdog -
[    2.661962] kmodloader: loading kernel modules from /etc/modules-boot.d/*
[    2.793102] usbcore: registered new interface driver usbfs
[    2.798909] usbcore: registered new interface driver hub
[    2.804516] usbcore: registered new device driver usb
[    2.820502] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    2.829762] ehci-platform: EHCI generic platform driver
[    2.940052] ehci-platform ehci-platform: EHCI Host Controller
[    2.945995] ehci-platform ehci-platform: new USB bus registered, assigned bus number 1
[    2.954406] ehci-platform ehci-platform: irq 15, io mem 0xb0001500
[    2.976024] ehci-platform ehci-platform: USB 2.0 started, EHCI 1.00, overcurrent ignored
[    2.985792] hub 1-0:1.0: USB hub found
[    2.990201] hub 1-0:1.0: 2 ports detected
[    2.999782] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[    3.008325] ohci-platform: OHCI generic platform driver
[    3.013884] ohci-platform ohci-platform: Generic Platform OHCI controller
[    3.020893] ohci-platform ohci-platform: new USB bus registered, assigned bus number 2
[    3.029132] ohci-platform ohci-platform: irq 13, io mem 0xb0001600
[    3.097569] hub 2-0:1.0: USB hub found
[    3.101976] hub 2-0:1.0: 2 ports detected
[    3.107514] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
[    3.116813] init: - preinit -
[    4.380871] random: jshn: uninitialized urandom read (4 bytes read)
[    4.570999] random: jshn: uninitialized urandom read (4 bytes read)
[    4.757577] random: jshn: uninitialized urandom read (4 bytes read)
[    5.325615] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[    5.331845] bcm63xx_enetsw bcm63xx_enetsw.0: link UP on port1, 100Mbps, full-duplex
[    5.332280] bcm63xx_enetsw bcm63xx_enetsw.0: link UP on port4, 100Mbps, full-duplex
[    5.348130] IPv6: ADDRCONF(NETDEV_UP): eth0.1: link is not ready
[    5.354684] IPv6: ADDRCONF(NETDEV_CHANGE): eth0.1: link becomes ready
Press the [f] key and hit [enter] to enter failsafe mode
Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level
[    6.336445] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[    8.858881] jffs2: notice: (364) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found.
[    8.876687] mount_root: switching to jffs2 overlay
[    8.921110] urandom-seed: Seeding with /etc/urandom.seed
[    9.111168] procd: - early -
[    9.114327] procd: - watchdog -
[    9.796155] procd: - watchdog -
[    9.799633] procd: - ubus -
[    9.925515] urandom_read: 3 callbacks suppressed
[    9.925526] random: ubusd: uninitialized urandom read (4 bytes read)
[    9.939150] random: ubusd: uninitialized urandom read (4 bytes read)
[    9.946248] random: ubusd: uninitialized urandom read (4 bytes read)
[    9.953932] procd: - init -
Please press Enter to activate this console.
[   10.578404] kmodloader: loading kernel modules from /etc/modules.d/*
[   10.594967] ip6_tables: (C) 2000-2006 Netfilter Core Team
[   10.620115] Loading modules backported from Linux version wt-2017-11-01-0-gfe248fc2c180
[   10.628348] Backport generated by backports.git v4.14-rc2-1-31-g86cf0e5d
[   10.641406] ip_tables: (C) 2000-2006 Netfilter Core Team
[   10.662388] nf_conntrack version 0.5.0 (1024 buckets, 4096 max)
[   10.756752] xt_time: kernel timezone is -0000
[   10.867745] PPP generic driver version 2.4.2
[   10.885369] NET: Registered protocol family 24
[   10.928904] PCI: Enabling device 0000:00:01.0 (0000 -> 0002)
[   10.937507] ieee80211 phy0: rt2x00lib_request_eeprom_file: Info - Loading EEPROM data from 'rt2x00.eeprom'.
[   10.947665] rt2800pci 0000:00:01.0: Direct firmware load for rt2x00.eeprom failed with error -2
[   10.956599] rt2800pci 0000:00:01.0: Falling back to user helper
[   11.062115] firmware rt2x00.eeprom: firmware_loading_store: map pages failed
[   11.069613] ieee80211 phy0: rt2x00lib_request_eeprom_file: Error - Failed to request EEPROM.
[   11.079471] rt2800pci: probe of 0000:00:01.0 failed with error -11
[   11.104276] kmodloader: done loading kernel modules from /etc/modules.d/*
[   20.940289] bcm63xx_enetsw bcm63xx_enetsw.0: link UP on port1, 100Mbps, full-duplex
[   20.948559] bcm63xx_enetsw bcm63xx_enetsw.0: link UP on port4, 100Mbps, full-duplex
[   20.963554] br-lan: port 1(eth0.1) entered blocking state
[   20.969125] br-lan: port 1(eth0.1) entered disabled state
[   20.975211] device eth0.1 entered promiscuous mode
[   20.980138] device eth0 entered promiscuous mode
[   21.001699] br-lan: port 1(eth0.1) entered blocking state
[   21.007258] br-lan: port 1(eth0.1) entered forwarding state
[   21.013190] IPv6: ADDRCONF(NETDEV_UP): br-lan: link is not ready
[   21.336528] br-wan: port 1(eth0.2) entered blocking state
[   21.342083] br-wan: port 1(eth0.2) entered disabled state
[   21.348233] device eth0.2 entered promiscuous mode
[   21.448161] br-wan: port 1(eth0.2) entered blocking state
[   21.453695] br-wan: port 1(eth0.2) entered forwarding state
[   21.952473] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
[   52.260098] random: crng init done
[   52.263540] random: 1 urandom warning(s) missed due to ratelimiting

状态系统主机名
OpenWrt

主机型号
Huawei HG622

架构
bcm63xx/96368MVWG_hg622 (0x6368/0xB2)

固件版本
OpenWrt 18.06.1 r7258-5eb055306f / LuCI openwrt-18.06 branch (git-18.228.31946-f64b152)

内核版本
4.9.120

本地时间
Sat Oct 13 05:25:34 2018

运行时间
1h 4m 0s

平均负载
1.24, 0.40, 0.19



内存可用数

3476 kB / 27864 kB (12%)

空闲数

1852 kB / 27864 kB (6%)

已缓冲

1624 kB / 27864 kB (5%)