大亚db120-b1刷了db120-openwrt.org.cn-bt-0312.bin后ping不通192.168.1.1怎么解决？

gzccx

请教一下，大亚db120-b1刷了db120-openwrt.org.cn-bt-0312.bin后ping不通192.168.1.1怎么解决？
CFE>
CFE>

CFE version 1.0.37-10.3 for BCM96358 (32bit,SP,BE)
Build Date: Thu Feb 12 13:10:57 CST 2009 (root@localhost.localdomain)
Copyright (C) 2000-2006 Broadcom Corporation.

Boot Address 0xbe000000

Initializing Arena.
Initializing Devices.
Parallel flash device: name AM29LV320MT|S29GL128-A, id 0x2201, size 16384KB
Flash Layout: Boot[0,0xbe000000] Kern[1,0xbe020000]
              AuxFS[95,0xbebe0000] Misc[126,0xbefc0000] PSI[127,0xbefe0000]
Flash RootFS Partition Length: 12320768
CFE using EMAC 0
Auto-negotiation timed-out
10 MB Half-Duplex (assumed)
CPU type 0x2A010: 300MHz, Bus: 133MHz, Ref: 64MHz
CPU running TP0
Total memory: 33554432 bytes (32MB)

Total memory used by CFE:  0x80401000 - 0x805285D0 (1209808)
Initialized Data:          0x8041E210 - 0x8041FDF0 (7136)
BSS Area:                  0x8041FDF0 - 0x804265D0 (26592)
Local Heap:                0x804265D0 - 0x805265D0 (1048576)
Stack Area:                0x805265D0 - 0x805285D0 (8192)
Text (code) segment:       0x80401000 - 0x8041E210 (119312)
Boot area (physical):      0x00529000 - 0x00569000
Relocation Factor:         I:00000000 - D:00000000

Board IP address                  : 192.168.1.1:ffffff00  
Host IP address                   : 192.168.1.159  
Gateway IP address                :   
Run from flash/host (f/h)         : h  
Default host run file name        : 308nfs6358  
Default host flash file name      : bcm963xx_fs_kernel  
Boot delay (0-9 seconds)          : 1  
Board Id (0-2)                    : 96358VW2  
Number of MAC Addresses (1-32)    : 24  
Base MAC Address                  : 00:1e:40:6c:b4:c5  
PSI Size (1-64) KBytes            : 24  
Flash Block Size (1-128) in KBytes: 128  
Auxillary File System Size Percent: 25  
Main Thread Number [0|1]          : 0  

*** Press any key to stop auto run (1 seconds) ***
Auto run second count down: 0
Booting from only image (0xbe020000) ...
Code Address: 0x80010000, Entry Address: 0x80010000
Decompression OK!
Entry at 0x80010000
Closing network.
Starting program at 0x80010000
Linux version 2.6.32.9 (openwrtcn@fedora) (gcc version 4.3.3 (GCC) ) #18 Wed Mar 31 00:21:18 CST 2010
Detected Broadcom 0x6358 CPU revision a1
CPU frequency is 300 MHz
32MB of RAM installed
registering 40 GPIOs
board_bcm963xx: CFE version: 1.0.37-10.3
bootconsole [early0] enabled
CPU revision is: 0002a010 (Broadcom BCM6358)
board_bcm963xx: board name: 96358VW2
Determined physical RAM map:
memory: 02000000 @ 00000000 (usable)
Initrd not found or empty - disabling initrd
Zone PFN ranges:
  Normal   0x00000000 -> 0x00002000
Movable zone start PFN for each node
early_node_map[1] active PFN ranges
    0: 0x00000000 -> 0x00002000
Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 8128
Kernel command line: root=/dev/mtdblock2 rootfstype=squashfs,jffs2 noinitrd console=ttyS0,115200
PID hash table entries: 128 (order: -3, 512 bytes)
Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)
Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)
Primary instruction cache 32kB, VIPT, 2-way, linesize 16 bytes.
Primary data cache 16kB, 2-way, VIPT, cache aliases, linesize 16 bytes
Memory: 29680k/32768k available (2096k kernel code, 3088k reserved, 365k data, 136k init, 0k highmem)
Hierarchical RCU implementation.
NR_IRQS:128
Calibrating delay loop... 299.00 BogoMIPS (lpj=598016)
Mount-cache hash table entries: 512
NET: Registered protocol family 16
registering PCI controller with io_map_base unset
bio: create slab <bio-0> at 0
Switching to clocksource MIPS
PCI: Enabling device 0000:00:01.0 (0000 -> 0002)
ssb: Sonics Silicon Backplane found on PCI device 0000:00:01.0
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 1024 (order: 1, 8192 bytes)
TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
TCP: Hash tables configured (established 1024 bind 1024)
TCP reno registered
NET: Registered protocol family 1
audit: initializing netlink socket (disabled)
type=2000 audit(0.287:1): initialized
squashfs: version 4.0 (2009/01/31) Phillip Lougher
Registering mini_fo version $Id$
JFFS2 version 2.2. (NAND) (SUMMARY)  &#169; 2001-2006 Red Hat, Inc.
msgmni has been set to 57
io scheduler noop registered
io scheduler deadline registered (default)
gpiodev: gpio device registered with major 254
gpiodev: gpio platform device registered with access mask FFFFFFFF
bcm63xx_uart.0: ttyS0 at MMIO 0xfffe0100 (irq = 10) is a bcm63xx_uart
console [ttyS0] enabled, bootconsole disabled
console [ttyS0] enabled, bootconsole disabled
bcm963xx_flash: Flash phys=0x1e000000, size=0x02000000, virt= 0xbe000000
Number of erase regions: 1
Primary Vendor Command Set: 0002 (AMD/Fujitsu Standard)
Primary Algorithm Table at 0040
Alternative Vendor Command Set: 0000 (None)
No Alternate Algorithm Table
Vcc Minimum:  2.7 V
Vcc Maximum:  3.6 V
No Vpp line
Typical byte/word write timeout: 64 &#181;s
Maximum byte/word write timeout: 512 &#181;s
Typical full buffer write timeout: 64 &#181;s
Maximum full buffer write timeout: 2048 &#181;s
Typical block erase timeout: 512 ms
Maximum block erase timeout: 4096 ms
Typical chip erase timeout: 524288 ms
Maximum chip erase timeout: 2097152 ms
Device size: 0x1000000 bytes (16 MiB)
Flash Device Interface description: 0x0002
  - supports x8 and x16 via BYTE# with asynchronous interface
Max. bytes in buffer write: 0x40
Number of Erase Block Regions: 1
  Erase Region #0: BlockSize 0x20000 bytes, 128 blocks
bcm963xx: Found 1 x16 devices at 0x0 in 16-bit bank
Amd/Fujitsu Extended Query Table at 0x0040
bootloc=5, NumEraseRegions=1.
bcm963xx: CFI does not contain boot bank location. Assuming top.
cfi->addr_unlock1 = 0x555, cfi->addr_unlock2 = 0x2aa
number of CFI chips: 1
  0: offset=0x0,size=0x0,blocks=131072
cfi_cmdset_0002: Disabling erase-suspend-program due to code brokenness.
bcm963xx_flash: Read Signature value of CFE1CFE1
bcm963xx_flash: CFE bootloader detected
i=0, tagid='bc300',  matchtagid='bccfe', Not matched.
i=1, tagid='bc300',  matchtagid='bc300', Matched.
CRC ok.
bcm963xx_flash: CFE boot tag found with version 6, board type 96358VW2, and tagid bc300.
bcm963xx_flash: Partition 0 is CFE offset 0 and length 20000
bcm963xx_flash: Partition 1 is kernel offset 20100 and length dff00
bcm963xx_flash: Partition 2 is rootfs offset 100000 and length ee0000
bcm963xx_flash: Partition 3 is nvram offset fe0000 and length 20000
bcm963xx_flash: Partition 4 is linux offset 20000 and length fc0000
bcm963xx_flash: Spare partition is 840000 offset and length 7a0000
Creating 5 MTD partitions on "bcm963xx":
0x000000000000-0x000000020000 : "CFE"
0x000000020100-0x000000100000 : "kernel"
mtd: partition "kernel" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
0x000000100000-0x000000fe0000 : "rootfs"
mtd: partition "rootfs" set to be root filesystem
mtd: partition "rootfs_data" created automatically, ofs=840000, len=7A0000
0x000000840000-0x000000fe0000 : "rootfs_data"
0x000000fe0000-0x000001000000 : "nvram"
0x000000020000-0x000000fe0000 : "linux"
bcm63xx_enet MII bus: probed
bcm63xx_wdt started, timer margin: 30 sec
Registered led device: adsl
Registered led device: ppp-fail
Registered led device: power
Registered led device: stop
TCP westwood registered
NET: Registered protocol family 17
802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
All bugs added by David S. Miller <davem@redhat.com>
VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
Freeing unused kernel memory: 136k freed
Please be patient, while OpenWrt loads ...
- preinit -
Press f<ENTER> to enter failsafe mode
- regular preinit -
switching to jffs2
mini_fo: using base directory: /
mini_fo: using storage directory: /jffs
- init -

gzccx

Please press Enter to activate this console. bcm63xx_enet bcm63xx_enet.0: attached PHY at address 1 [Broadcom BCM63XX (2)]
eth1: link forced UP - 100/full - flow control off/off
device eth1 entered promiscuous mode
br-lan: port 1(eth1) entering forwarding state
Generic kernel compatibility enabled based on linux-next next-20100113
cfg80211: Calling CRDA to update world regulatory domain
cfg80211: World regulatory domain updated:
    (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
    (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
    (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
    (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
    (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
    (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
SCSI subsystem initialized
roboswitch: Probing device eth0: Failed to enable switch
roboswitch: Probing device eth1: found a 5325! It's a 5350.
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
b43-phy0: Broadcom 4318 WLAN found (core revision 9)
Registered led device: b43-phy0::tx
Registered led device: b43-phy0::rx
Registered led device: b43-phy0::radio
Broadcom 43xx driver loaded [ Features: PNL, Firmware-ID: FW13 ]
NTFS driver 2.1.29 [Flags: R/O MODULE].
PPP generic driver version 2.4.2
ip_tables: (C) 2000-2006 Netfilter Core Team
NET: Registered protocol family 24
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
bcm63xx_ehci bcm63xx_ehci.0: BCM63XX integrated EHCI controller
bcm63xx_ehci bcm63xx_ehci.0: new USB bus registered, assigned bus number 1
bcm63xx_ehci bcm63xx_ehci.0: irq 18, io mem 0xfffe1300
bcm63xx_ehci bcm63xx_ehci.0: USB 2.0 started, EHCI 1.00
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
nf_conntrack version 0.5.0 (465 buckets, 1860 max)
CONFIG_NF_CT_ACCT is deprecated and will be removed soon. Please use
nf_conntrack.acct=1 kernel parameter, acct=1 nf_conntrack module option or
sysctl net.netfilter.nf_conntrack_acct=1 to enable it.
usb 1-2: new high speed USB device using bcm63xx_ehci and address 2
usb 1-2: configuration #1 chosen from 1 choice
IMQ driver loaded successfully.
        Hooking IMQ before NAT on PREROUTING.
        Hooking IMQ after NAT on POSTROUTING.
xt_time: kernel timezone is -0000
ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
bcm63xx_ohci bcm63xx_ohci.0: BCM63XX integrated OHCI controller
bcm63xx_ohci bcm63xx_ohci.0: new USB bus registered, assigned bus number 2
bcm63xx_ohci bcm63xx_ohci.0: irq 13, io mem 0xfffe1400
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 1 port detected
uhci_hcd: USB Universal Host Controller Interface driver
usbcore: registered new interface driver usblp
Initializing USB Mass Storage driver...
scsi0 : SCSI emulation for USB Mass Storage devices
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
fuse init (API version 7.13)
scsi 0:0:0:0: Direct-Access     SanDisk  Cruzer Crossfire 0.1  PQ: 0 ANSI: 2
sd 0:0:0:0: [sda] 2001888 512-byte logical blocks: (1.02 GB/977 MiB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Assuming drive cache: write through
sd 0:0:0:0: [sda] Assuming drive cache: write through
sda: sda1
sd 0:0:0:0: [sda] Assuming drive cache: write through
sd 0:0:0:0: [sda] Attached SCSI removable disk
FAT: utf8 is not a recommended IO charset for FAT filesystems, filesystem will be case sensitive!



BusyBox v1.15.3 (2010-03-04 11:05:33 CST) built-in shell (ash)
Enter 'help' for a list of built-in commands.

  _______                     ________        __
|       |.-----.-----.-----.|  |  |  |.----.|  |_
|   -   ||  _  |  -__|     ||  |  |  ||   _||   _|
|_______||   __|_____|__|__||________||__|  |____|
          |__| W I R E L E S S   F R E E D O M
KAMIKAZE (bleeding edge, r19957) ------------------
  * 10 oz Vodka       Shake well with ice and strain
  * 10 oz Triple sec  mixture into 10 shot glasses.
  * 10 oz lime juice  Salute!
---------------------------------------------------
root@OpenWrt:/#

gzccx

已经好了，不知道为什么LAN4是PING不通的。LAN1，2，3都可以PING通。
但是无线不能用呀！一打开无线就不能上网，一关闭无线就可以上网！真奇怪。。

meiyunjie

DB120的LAN4刷OPENWRT后是wan口，当然ping不通

gzccx

无线的问题怎么解决？

exition

你看一下wlan的位置 要和lan捆在一起 否则就是wan

i15916

楼主能帮我看看我的  要怎么弄不?

m29的到这里就不动了

Boot Address 0xbe000000

Initializing Arena.
Initializing Devices.
Parallel flash device id 0279 is not supported.

*** Board is not initialized properly ***

Press:  <enter> to use current value
        '-' to go previous parameter
        '.' to clear the current value
        'x' to exit this command
96358VW2         ------- 0
96358VW          ------- 1
96358GWVG        ------- 2
96358MV2G        ------- 3
96358M           ------- 4
96358B           ------- 5
96358BGWE_OEM1   ------- 6
96359PONG        ------- 7
96358SV          ------- 8
96358VW2_b20     ------- 9
Board Id (0-9)                    :  

要我选一个   网口都不通.  无法进升级页面

  选那个  都不可以  还是一开就回到这里

i15916

CFE version 1.0.37-10.3 for BCM96358 (32bit,SP,BE)
Build Date: 二  1月 29 07:41:15 CST 2008 (root@ZTJ)
Copyright (C) 2000-2006 Broadcom Corporation.

Boot Address 0xbe000000

Initializing Arena.
Initializing Devices.
Parallel flash device id 0279 is not supported.

*** Board is not initialized properly ***

Press:  <enter> to use current value
        '-' to go previous parameter
        '.' to clear the current value
        'x' to exit this command
96358VW2         ------- 0
96358VW          ------- 1
96358GWVG        ------- 2
96358MV2G        ------- 3
96358M           ------- 4
96358B           ------- 5
96358BGWE_OEM1   ------- 6
96359PONG        ------- 7
96358SV          ------- 8
96358VW2_b20     ------- 9
Board Id (0-9)                    :  0
Number of MAC Addresses (1-32)    :  0  24
Base MAC Address                  :  00:00:00:00:00:00  00:25:10:c1:12:e3
PSI Size (1-64) KBytes            :  24  24
Flash Block Size (1-128) in KBytes:  0  128
Auxillary File System Size Percent:  0  25
Main Thread Number [0|1]          :  0  0
Flash layout changed. Need to erase all flash except bootrom
Invalid command: "e"
Available commands:

Flash Layout: Boot[0,0x00000000] Kern[-1,0xbdffffff]
              AuxFS[-1,0x00000000] Misc[-1,0x00000000] PSI[-1,0x00000000]
Flash RootFS Partition Length: 1107296257
Auto-negotiation timed-out
10 MB Half-Duplex (assumed)
CPU type 0x2A010: 300MHz, Bus: 133MHz, Ref: 64MHz
CPU running TP0
Total memory: 33554432 bytes (32MB)

Total memory used by CFE:  0x80401000 - 0x805285A0 (1209760)
Initialized Data:          0x8041DD30 - 0x8041FDC0 (8336)
BSS Area:                  0x8041FDC0 - 0x804265A0 (26592)
Local Heap:                0x804265A0 - 0x805265A0 (1048576)
Stack Area:                0x805265A0 - 0x805285A0 (8192)
Text (code) segment:       0x80401000 - 0x8041DD30 (118064)
Boot area (physical):      0x00529000 - 0x00569000
Relocation Factor:         I:00000000 - D:00000000

Use default boot line parameters: e=192.168.1.1:ffffff00 h=192.168.1.159 g= r=h f=308nfs6358 i=bcm963xx_fs_kernel d=1 p=0
Board IP address                  : 192.168.1.1:ffffff00  
Host IP address                   : 192.168.1.159  
Gateway IP address                :   
Run from flash/host (f/h)         : h  
Default host run file name        : 308nfs6358  
Default host flash file name      : bcm963xx_fs_kernel  
Boot delay (0-9 seconds)          : 1  
Board Id (0-9)                    :   
Number of MAC Addresses (1-32)    : 0  
Base MAC Address                  : 00:00:00:00:00:00  
PSI Size (1-64) KBytes            : 24  
Flash Block Size (1-128) in KBytes: 0  
Auxillary File System Size Percent: 0  
Main Thread Number [0|1]          : 0  

*** Press any key to stop auto run (1 seconds) ***
Auto run second count down: 1
web info: Waiting for connection on socket 0.
CFE>