找回密码
 立即注册

QQ登录

只需一步,快速开始

搜索
广告投放联系QQ68610888
查看: 191981|回复: 902

[20120101] OpenWrt for AR9341 (841n v8/300r v3) 准完美版 灯完全正常/网口抽

 火... [复制链接]
发表于 2011-12-12 22:12 | 显示全部楼层 |阅读模式
本帖最后由 729650915 于 2012-1-1 14:56 编辑

RT

20120101

传送门https://www.right.com.cn/forum/thread-72486-1-1.html

修正网口灯 灯都正常了
新驱动似乎有些抽风 有时网口会抽 多重启几下才正常

20111215

下载地址
http://115.com/file/c2mttu62#
20111215-openwrt-ar71xx-generic-tl-wr841n-v8-squashfs-sysupgrade.7z
原厂系统的请先改机刷20111212的编程器固件再更新到此

修复reset按键 添加所有led  wan/lan led暂时只能自行设置显示状态
  1. root@TP-LINK:/sys/class/leds# ls
  2. ath9k-phy0            tp-link:green:lan3    tp-link:green:system
  3. tp-link:green:lan1    tp-link:green:lan4    tp-link:green:wan
  4. tp-link:green:lan2    tp-link:green:qss     tp-link:green:wlan
  5. root@TP-LINK:/sys/class/leds#
复制代码



20111212

下载地址
http://115.com/file/be3v766k#
20111212-ar9341.7z
包含4m/8m编程器固件(fullflash文件夹里) 4m/8m单独uboot(uboot文件夹里) 通用固件(firmware文件夹里) 无线分区(art文件夹里)
编程器刷只需根据你的flash大小刷fullflash文件夹里的文件即可
mac在0x1fc00 pin在0x1fe00

注: 需要把内存换到32M或更大 Flash换到4M或更大

已知bug:
1. 所有灯都抽风(开机后一直保持一个样)
2. reset按键无效

本帖子中包含更多资源

您需要 登录 才可以下载或查看,没有账号?立即注册

×

评分

参与人数 15恩山币 +19 收起 理由
hxjxyz + 1 神马都是浮云!
mury + 1 什么时候能整个1041n的8m uboot出来?
xp15g + 1 泥马,真给力!
ensky + 1 赞一个,你是我的呕像!
daols + 1 持续关注...
a291899192 + 1 强,支持
hhhjjj159 + 1 很好的固件,支持
test0x01 + 1 好东西
yy5409 + 1 希望继续更新
w506 + 1 希望更加完善,支持尽快破解。谢谢
icerol + 3 DYQ出品,必属精品!
leangjia + 1 很强!
99010 + 1 支持原创
coolslob + 1 原创内容
phantom-gy + 3 good

查看全部评分

我的恩山、我的无线 The best wifi forum is right here.
 楼主| 发表于 2011-12-12 22:12 | 显示全部楼层
启动信息(8m):
U-Boot 1.1.4 (Dec 10 2011 - 17:19:13)


made by dyq(QQ:729650915)
tested by ironcake(QQ:110782278)

U-boot AP123


DRAM:  64 MB
led turning on for 1s...
id read 0x100000ff
flash size 8MB, sector count = 128
Flash:  8 MB
Using default environment

In:    serial
Out:   serial
Err:   serial
Net:   ag934x_enet_initialize...
No valid address in Flash. Using fixed address
No valid address in Flash. Using fixed address
wasp  reset mask:c03300
WASP ----> S27 PHY
: cfg1 0x5 cfg2 0x7114
eth0: 00:03:7f:09:0b:ad
s27 reg init
athrs27_phy_setup ATHR_PHY_CONTROL 4 :1000
athrs27_phy_setup ATHR_PHY_SPEC_STAUS 4 :10
eth0 up
WASP ----> S27 PHY
: cfg1 0xf cfg2 0x7214
eth1: 00:03:7f:09:0b:ad
s27 reg init lan
ATHRS27: resetting s27
ATHRS27: s27 reset done
athrs27_phy_setup ATHR_PHY_CONTROL 0 :1000
athrs27_phy_setup ATHR_PHY_SPEC_STAUS 0 :10
athrs27_phy_setup ATHR_PHY_CONTROL 1 :1000
athrs27_phy_setup ATHR_PHY_SPEC_STAUS 1 :10
athrs27_phy_setup ATHR_PHY_CONTROL 2 :1000
athrs27_phy_setup ATHR_PHY_SPEC_STAUS 2 :50
athrs27_phy_setup ATHR_PHY_CONTROL 3 :1000
athrs27_phy_setup ATHR_PHY_SPEC_STAUS 3 :10
eth1 up
eth0, eth1
Autobooting in 1 seconds, press t to stop
## Booting image at 9f020000 ...
   Uncompressing Kernel Image ... OK

Starting kernel ...
我的恩山、我的无线 The best wifi forum is right here.
回复

使用道具 举报

 楼主| 发表于 2011-12-12 22:13 | 显示全部楼层
[    0.000000] Linux version 2.6.39.4 (dyq@dyq-desktop) (gcc version 4.5.4 20110808 (prerelease) (Linaro GCC 4.5-2011.08) ) #1 Mon Dec 12 21:33:45 CST 2011
[    0.000000] bootconsole [early0] enabled
[    0.000000] CPU revision is: 0001974c (MIPS 74Kc)
[    0.000000] SoC: Atheros AR9341 rev 1
[    0.000000] Clocks: CPU:500.000MHz, DDR:400.000MHz, AHB:200.000MHz, Ref:25.000MHz
[    0.000000] Determined physical RAM map:
[    0.000000]  memory: 04000000 @ 00000000 (usable)
[    0.000000] Initrd not found or empty - disabling initrd
[    0.000000] Zone PFN ranges:
[    0.000000]   Normal   0x00000000 -> 0x00004000
[    0.000000] Movable zone start PFN for each node
[    0.000000] early_node_map[1] active PFN ranges
[    0.000000]     0: 0x00000000 -> 0x00004000
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 16256
[    0.000000] Kernel command line:  board=TL-WR841N-v8 console=ttyS0,115200 rootfstype=squashfs,jffs2 noinitrd
[    0.000000] PID hash table entries: 256 (order: -2, 1024 bytes)
[    0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
[    0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
[    0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
[    0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
[    0.000000] Writing ErrCtl register=00000000
[    0.000000] Readback ErrCtl register=00000000
[    0.000000] Memory: 61848k/65536k available (2013k kernel code, 3688k reserved, 393k data, 184k init, 0k highmem)
[    0.000000] SLUB: Genslabs=9, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[    0.000000] NR_IRQS:80
[    0.000000] Calibrating delay loop... 249.44 BogoMIPS (lpj=1247232)
[    0.070000] pid_max: default: 32768 minimum: 301
[    0.070000] Mount-cache hash table entries: 512
[    0.080000] NET: Registered protocol family 16
[    0.080000] MIPS: machine is TP-LINK TL-WR841N v8
[    0.090000] firmware by dyq (QQ:729650915)
[    0.500000] bio: create slab <bio-0> at 0
[    0.510000] Switching to clocksource MIPS
[    0.520000] NET: Registered protocol family 2
[    0.520000] IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.520000] TCP established hash table entries: 2048 (order: 2, 16384 bytes)
[    0.530000] TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
[    0.530000] TCP: Hash tables configured (established 2048 bind 2048)
[    0.540000] TCP reno registered
[    0.540000] UDP hash table entries: 256 (order: 0, 4096 bytes)
[    0.550000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[    0.560000] NET: Registered protocol family 1
[    0.580000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    0.580000] JFFS2 version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[    0.590000] msgmni has been set to 120
[    0.600000] io scheduler noop registered
[    0.600000] io scheduler deadline registered (default)
[    0.610000] Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled
[    0.630000] serial8250.0: ttyS0 at MMIO 0x18020000 (irq = 11) is a 16550A
[    0.640000] console [ttyS0] enabled, bootconsole disabled
[    0.640000] console [ttyS0] enabled, bootconsole disabled
[    0.650000] Atheros AR71xx SPI Controller driver version 0.2.4
[    0.660000] m25p80 spi0.0: found mx25l6405d, expected m25p80
[    0.670000] m25p80 spi0.0: mx25l6405d (8192 Kbytes)
[    0.680000] 6 tp-link partitions found on MTD device spi0.0
[    0.680000] Creating 6 MTD partitions on "spi0.0":
[    0.690000] 0x000000000000-0x000000020000 : "u-boot"
[    0.700000] 0x000000020000-0x000000100000 : "kernel"
[    0.700000] 0x000000100000-0x0000007f0000 : "rootfs"
[    0.710000] mtd: partition "rootfs" set to be root filesystem
[    0.720000] mtd: partition "rootfs_data" created automatically, ofs=260000, len=590000
[    0.730000] 0x000000260000-0x0000007f0000 : "rootfs_data"
[    0.730000] 0x0000007f0000-0x000000800000 : "art"
[    0.740000] 0x000000020000-0x0000007f0000 : "firmware"
[    0.750000] 0x000000000000-0x000000800000 : "fullflash"
[    1.100000] ag71xx_mdio: probed
[    1.100000] eth0: Atheros AG71xx at 0xba000000, irq 5
[    1.660000] eth1: Atheros AG71xx at 0xb9000000, irq 4
[    2.210000] Atheros AR71xx hardware watchdog driver version 0.1.0
[    2.220000] TCP westwood registered
[    2.220000] NET: Registered protocol family 17
[    2.230000] 802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
[    2.240000] All bugs added by David S. Miller <davem@redhat.com>
[    2.250000] VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
[    2.260000] Freeing unused kernel memory: 184k freed
[    4.410000] Button Hotplug driver version 0.4.1
[    4.440000] eth0: link up (1000Mbps/Full duplex)
- preinit -
[    4.560000] leds-gpio: probe of leds-gpio failed with error -22
Press the [f] key and hit [enter] to enter failsafe mode
- regular preinit -
[    7.890000] JFFS2 notice: (423) jffs2_build_xattr_subsystem: complete building xattr subsystem, 16 of xdatum (0 unchecked, 16 orphan) and 22 of xref (0 dead, 22 orphan) found.
switching to jffs2
- init -
[    8.040000] eth0: link down
[    8.550000] Compat-wireless backport release: compat-wireless-2011-11-29
[    8.560000] Backport based on wireless-testing.git master-2011-12-01
[    8.830000] cfg80211: Calling CRDA to update world regulatory domain
[    9.500000] cfg80211: World regulatory domain updated:
[    9.510000] cfg80211:     (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[    9.520000] cfg80211:     (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[    9.530000] cfg80211:     (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[    9.540000] cfg80211:     (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[    9.540000] cfg80211:     (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[    9.550000] cfg80211:     (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[   10.210000] ieee80211 phy0: Atheros AR9340 Rev:0 mem=0xb8100000, irq=78
[   10.220000] cfg80211: Calling CRDA for country: US
[   10.360000] PPP generic driver version 2.4.2
[   10.380000] cfg80211: Regulatory domain changed to country: US
[   10.390000] cfg80211:     (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[   10.400000] cfg80211:     (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2700 mBm)
[   10.410000] cfg80211:     (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 1700 mBm)
[   10.410000] cfg80211:     (5250000 KHz - 5330000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[   10.420000] cfg80211:     (5490000 KHz - 5600000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[   10.430000] cfg80211:     (5650000 KHz - 5710000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[   10.440000] cfg80211:     (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 3000 mBm)
[   10.630000] ip_tables: (C) 2000-2006 Netfilter Core Team
[   10.770000] NET: Registered protocol family 24
[   10.900000] nf_conntrack version 0.5.0 (969 buckets, 3876 max)

Please press Enter to activate this console. [   12.690000] eth0: link up (1000Mbps/Full duplex)
[   12.890000] device eth0 entered promiscuous mode
[   12.930000] br-lan: port 1(eth0) entering forwarding state
[   12.940000] br-lan: port 1(eth0) entering forwarding state
[   13.120000] eth1: link up (100Mbps/Full duplex)
[   14.580000] cfg80211: Calling CRDA for country: CN
[   14.750000] cfg80211: Regulatory domain changed to country: CN
[   14.750000] cfg80211:     (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[   14.760000] cfg80211:     (2402000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm)
[   14.770000] cfg80211:     (5735000 KHz - 5835000 KHz @ 40000 KHz), (N/A, 3000 mBm)
[   16.300000] device wlan0 entered promiscuous mode
[   16.300000] br-lan: port 2(wlan0) entering forwarding state
[   16.310000] br-lan: port 2(wlan0) entering forwarding state
[   18.460000] device wlan0 left promiscuous mode
[   18.470000] br-lan: port 2(wlan0) entering forwarding state
[   18.590000] device wlan0 entered promiscuous mode
[   18.600000] br-lan: port 2(wlan0) entering forwarding state
[   18.600000] br-lan: port 2(wlan0) entering forwarding state



BusyBox v1.19.3 (2011-12-11 03:51:37 CST) built-in shell (ash)
Enter 'help' for a list of built-in commands.

  _______                     ________        __
|       |.-----.-----.-----.|  |  |  |.----.|  |_
|   -   ||  _  |  -__|     ||  |  |  ||   _||   _|
|_______||   __|_____|__|__||________||__|  |____|
          |__| W I R E L E S S   F R E E D O M
ATTITUDE ADJUSTMENT (bleeding edge, r29486, mod by dyq) --
  * 1/4 oz Vodka      Pour all ingredients into mixing
  * 1/4 oz Gin        tin with ice, strain into glass.
  * 1/4 oz Amaretto
  * 1/4 oz Triple sec
  * 1/4 oz Peach schnapps
  * 1/4 oz Sour mix
  * 1 splash Cranberry juice
-----------------------------------------------------
root@TP-LINK:/# cat /proc/cpuinfo
system type             : Atheros AR9341 rev 1
machine                 : TP-LINK TL-WR841N v8
processor               : 0
cpu model               : MIPS 74Kc V4.12
BogoMIPS                : 249.44
wait instruction        : yes
microsecond timers      : yes
tlb_entries             : 32
extra interrupt vector  : yes
hardware watchpoint     : yes, count: 4, address/irw mask: [0x0000, 0x0ff8, 0x0ff8, 0x0ff8]
ASEs implemented        : mips16
shadow register sets    : 1
kscratch registers      : 0
core                    : 0
VCED exceptions         : not available
VCEI exceptions         : not available

root@TP-LINK:/#
我的恩山、我的无线 The best wifi forum is right here.
回复

使用道具 举报

发表于 2011-12-12 22:14 | 显示全部楼层
抢个板凳!赞!
我的恩山、我的无线 The best wifi forum is right here.
回复

使用道具 举报

发表于 2011-12-12 22:16 | 显示全部楼层
本帖最后由 cjzzz 于 2011-12-12 23:46 编辑







本帖子中包含更多资源

您需要 登录 才可以下载或查看,没有账号?立即注册

×
我的恩山、我的无线 The best wifi forum is right here.
回复

使用道具 举报

发表于 2011-12-12 22:40 | 显示全部楼层
多谢分享 看来又要出神机了 哈哈
我的恩山、我的无线 The best wifi forum is right here.
回复

使用道具 举报

发表于 2011-12-12 23:10 | 显示全部楼层
不错,找个机会开源一下把
我的恩山、我的无线 The best wifi forum is right here.
回复

使用道具 举报

发表于 2011-12-13 14:12 | 显示全部楼层
我的FW300R V3之前已经刷过OP了,现在再刷这个固件可以在WEB下刷吗,刷好后可以安装NWAN吗?
我的恩山、我的无线 The best wifi forum is right here.
回复

使用道具 举报

发表于 2011-12-13 15:43 | 显示全部楼层
这个牛逼的,一定要顶
我的恩山、我的无线 The best wifi forum is right here.
回复

使用道具 举报

发表于 2011-12-13 19:37 | 显示全部楼层
缩水的也能刷吗》?


         ________  ________             __      __  ____   _  __   ___
        |________||   ___  |           |  |    |  ||    \ | ||  | /  /
           |  |   |  |___| |   __ __   |  |    |  ||     \| ||  |/  /
           |  |   |   _____|  |__ __|  |  |___ |  || |\     ||      \
           |__|   |__|                 |______||__||_| \____||__|\___\


                            Software Platform for MIPS
Creation date: Jul  5 2011, 09:13:06 (huangqingjia@tp-link.net)
Copyright(C) 2001-2012 by TP-LINK TECHNOLOGIES CO., LTD.
CPU: AR9341: AP123 Board
CPU freq: 500 MHZ
SDRAM size: 16 MB
ipaddr:192.168.1.1
serverip:192.168.1.100
file:vxWorks.img

"
Press Ctrl+C to stop auto-boot...
0
auto-booting...
Uncompressing...done
Starting at 0x80001000...
我的恩山、我的无线 The best wifi forum is right here.
回复

使用道具 举报

发表于 2011-12-14 12:18 | 显示全部楼层
300r v3要改硬件吗?改了刷了好用不
我的恩山、我的无线 The best wifi forum is right here.
回复

使用道具 举报

发表于 2011-12-14 14:02 | 显示全部楼层
不错呀。等完善结果的。
我的恩山、我的无线 The best wifi forum is right here.
回复

使用道具 举报

发表于 2011-12-14 14:21 | 显示全部楼层
顶一下牛人!顶完再加分。
我的恩山、我的无线 The best wifi forum is right here.
回复

使用道具 举报

发表于 2011-12-14 23:05 | 显示全部楼层
看看
我的恩山、我的无线 The best wifi forum is right here.
回复

使用道具 举报

发表于 2011-12-15 09:25 | 显示全部楼层
感谢分享!
我的恩山、我的无线 The best wifi forum is right here.
回复

使用道具 举报

您需要登录后才可以回帖 登录 | 立即注册

本版积分规则

有疑问请添加管理员QQ86788181|手机版|小黑屋|Archiver|恩山无线论坛(常州市恩山计算机开发有限公司版权所有) ( 苏ICP备05084872号 )

GMT+8, 2024-3-29 02:21

Powered by Discuz! X3.5

© 2001-2024 Discuz! Team.

| 江苏省互联网有害信息举报中心 举报信箱:js12377 | @jischina.com.cn 举报电话:025-88802724 本站不良内容举报信箱:68610888@qq.com 举报电话:0519-86695797

快速回复 返回顶部 返回列表