LINKSYS E2000 TTL线修复出现以下单词该怎么办呢
各位大侠，linksys e2000砖了，修复过程出现以下字母。帮忙看看该怎么办啊CFE version 5.10.56.51 based on BBP 1.0.37 for BCM947XX (32bit,SP,LE)
Build Date: Fri Oct8 08:52:14 HKT 2010 (hue@sw1)
Copyright (C) 2000-2008 Broadcom Corporation.
Init Arena
Init Devs.
No DPN
This is a Serial Flash
Boot partition size = 262144(0x40000)
Found a 8MB ST compatible serial flash
Partition information:
boot #00 00000000 -> 0003FFFF(262144)
trx #01 00040000 -> 0004001B(28)
os #02 0004001C -> 007F0FFF(8064996)
nvram #03 007F1000 -> 007FFFFF(61440)
Partition information:
boot #00 00000000 -> 0003FFFF(262144)
trx #01 00040000 -> 007F0FFF(8065024)
nvram #02 007F1000 -> 007FFFFF(61440)
BCM47XX_GMAC_ID
et0: Broadcom BCM47XX 10/100/1000 Mbps Ethernet Controller 5.10.56.51
CPU type 0x19740: 354MHz
Tot mem: 32768 KBytes
CFE mem: 0x80700000 - 0x807A1350 (660304)
Data: 0x80733430 - 0x807366F0 (12992)
BSS: 0x807366F0 - 0x8073B350 (19552)
Heap: 0x8073B350 - 0x8079F350 (409600)
Stack: 0x8079F350 - 0x807A1350 (8192)
Text: 0x80700000 - 0x80733428 (209960)
Boot version: v5.4
The boot is CFE
Nothing...
### CLKDIV= 0x80a082c, SFlashClkDiv=8 clkdivsf=2 ###
### Change it to 0x20a082c (2) ###
CMD:
Device eth0:hwaddr C0-C1-C0-47-6D-58, ipaddr 192.168.1.1, mask 255.255.255.0
gateway not set, nameserver not set
CMD:
Check CRC of image1
Len: 0x6CD000 (7131136) (0xBC040000)
Offset0: 0x1C (28) (0xBC04001C)
Offset1: 0xAD8 (2776)(0xBC040AD8)
Offset2: 0xE4800 (935936) (0xBC124800)
Header CRC: 0x6B4CE854
Calculate CRC: 0x6B4CE854
Image 1 is OK
Try to load image 1.
Waiting for 5 seconds to upgrade ...
CMD:
Loader:raw Filesys:tftp Dev:eth0 File:: Options:(null)
Loading: _tftpd_open(): retries=0/5
_tftpd_open(): retries=1/5
_tftpd_open(): retries=2/5
_tftpd_open(): retries=3/5
_tftpd_open(): retries=4/5
### Start=464638215 E=1426043705 Delta=961405490 ###
Failed.
Could not load :: Timeout occured
CMD:
Loader:raw Filesys:raw Dev:flash0.os File: Options:(null)
Loading: .. 5192 bytes read
### Start=1432385781 E=1435449418 Delta=3063637 ###
Entry at 0x80001000
Closing network.
Starting program at 0x80001000
1，设定网关为192.168.1.1，IP地址192.168.1.100-149（随便选个），子网掩码：192.168.1.1；
2，按住ctrl键和c键，接通路由器电源；
3，进入cfe，
4，输入命令flash后回车；
5，TFTP正确的固件就行了，最好先刷原产固件。
这个机器修复和linksys系列路由步骤一样，CFE核心还是以前的。
不清楚的话Q我：547362435 不懂帮顶
页:
[1]