这才是841N V8 TTL正确接法，15楼。。。。。。。。。。。。。。。。。。。！！！
本帖最后由 lph1216 于 2013-6-25 22:50 编辑好像是错了。。。 RXTX接反了吗 本帖最后由 lph1216 于 2013-1-8 20:30 编辑
zy900114 发表于 2013-1-8 20:26 static/image/common/back.gif
RXTX接反了吗
没有啊，换一下RX和TX。。。TTL板上的RX灯和TX灯还都不亮。。。再交换一下，至少RX灯亮了。。。同样接法，另一条TTL线（以前的旧线），乱码。。。 lph1216 发表于 2013-1-8 20:28 static/image/common/back.gif
没有啊，换一下RX和TX。。。TTL板上的RX灯和TX灯还都不亮。。。再交换一下，至少RX灯亮了。。。同样接法， ...
PL2303的TTL？貌似灯要拆掉 zy900114 发表于 2013-1-8 20:29 static/image/common/back.gif
PL2303的TTL？貌似灯要拆掉
对，新买的TTL是PL2303。。。灯拆掉？？？？我觉得先不考虑灯。。。。我的旧TTL线能显示，但乱码。。问题还是在841N的主板上 lph1216 发表于 2013-1-8 20:31 static/image/common/back.gif
对，新买的TTL是PL2303。。。灯拆掉？？？？我觉得先不考虑灯。。。。我的旧TTL线能显示，但乱码。。问题 ...
旧TTL有灯吗？ zy900114 发表于 2013-1-8 20:36 static/image/common/back.gif
旧TTL有灯吗？
没有。。。 lph1216 发表于 2013-1-8 20:43 static/image/common/back.gif
没有。。。
我记得有个帖子说灯拉低了信号，我的就是PL2303，拆了灯，输出没问题 zy900114 发表于 2013-1-8 20:47 static/image/common/back.gif
我记得有个帖子说灯拉低了信号，我的就是PL2303，拆了灯，输出没问题
连接时，RX灯是亮的，TX灯不亮，拆掉TX灯？铜线短接？ 俩灯直接拆掉
本帖最后由 lph1216 于 2013-1-8 21:09 编辑
zy900114 发表于 2013-1-8 20:53 static/image/common/back.gif
俩灯直接拆掉
灯拆了。。。能显示了。。。但乱码啊。。。跟我另一条旧的不带灯TTL 一样结果
你的V8跟我的一样？没有动主板上的电容、电阻或什么的？
115200设置无误。。。。。。。。 没有动QQ181062572
哎。。。搞不定啊。。。。。。。。 本帖最后由 lph1216 于 2013-1-9 21:55 编辑
经过多日研究。。。841N V8终于不乱码了。。。这些信息对吗？我的841N原装4M FLASH，16M内存被我改成了64M。。。图中“TP6”为TX，但接这儿会乱码，把TTL的TX接到图中右侧的“R89”的“右侧点”。。。就不乱码了。。。这些信息对不对啊？如果正确，我就做下一步了。。。
以下是SECURECRT的输出信息
U-Boot 1.1.4 (Aug 27 2012 - 00:43:10)
U-boot AP123
DRAM:64 MB
Top of RAM usable for U-Boot at: 84000000
Reserving 138k for U-Boot at: 83fdc000
Reserving 192k for malloc() at: 83fac000
Reserving 44 Bytes for Board Info at: 83fabfd4
Reserving 36 Bytes for Global Data at: 83fabfb0
Reserving 128k for boot params() at: 83f8bfb0
Stack Pointer at: 83f8bf98
Now running in RAM - U-Boot at: 83fdc000
Flash Manuf Id 0x1, DeviceId0 0x2, DeviceId1 0x15
flash size 4MB, sector count = 64
Flash:4 MB
Using default environment
In: serial
Out: serial
Err: serial
Net: ag934x_enet_initialize...
waspreset mask:c03300
WASP ----> S27 PHY
: cfg1 0x80000000 cfg2 0x7114
eth0: 14:e6:e4:4c:df:19
s27 reg init
athrs27_phy_setup ATHR_PHY_CONTROL 4 :1000
athrs27_phy_setup ATHR_PHY_SPEC_STAUS 4 :10
tpltpltpleth0 up
WASP ----> S27 PHY
: cfg1 0xf cfg2 0x7214
eth1: 14:e6:e4:4c:df:18
s27 reg init lan
ATHRS27: resetting s27
ATHRS27: s27 reset done
athrs27_phy_setup ATHR_PHY_CONTROL 0 :1000
athrs27_phy_setup ATHR_PHY_SPEC_STAUS 0 :10
athrs27_phy_setup ATHR_PHY_CONTROL 1 :1000
athrs27_phy_setup ATHR_PHY_SPEC_STAUS 1 :10
athrs27_phy_setup ATHR_PHY_CONTROL 2 :1000
athrs27_phy_setup ATHR_PHY_SPEC_STAUS 2 :10
athrs27_phy_setup ATHR_PHY_CONTROL 3 :1000
athrs27_phy_setup ATHR_PHY_SPEC_STAUS 3 :10
tplteth1 up
eth0, eth1
Load Default Boot Params.
Autobooting in 1 seconds
pltUncompressing...pltdone
pAttaching interface lo0... done
Rx clbufs 2048 each of size 1756
eth_rx_netpool_init: allocated, pDmaBuf=0x80b78850, buffend = 80eea854
lATHRS27: resetting s27
ATHRS27: s27 reset done
teth_rx_netpool_init: done already!
pltpltpltpAttached IPv4 interface to mirror unit 0
lusrAppInitEx: 112: GPIO_OE = 30310
usrAppInitEx: 113: CP0 CONFIG = 80208483
usrAppInitEx: 114: CP0 CONFIG1 = bee3519e
-->starting wireless...
APCFG task id 80996b10
sysWlanInit ...
Create WLAN event task tWLANEventTask
Create mem partion 0x809752e0 for size 86016
AH_CAL_IN_FLASH_AHB
Boostrap clock 25MHz
ar9300RadioAttach: Need analog access recipe!!
Restoring Cal data from Flash
ath_get_caps rx chainmask mismatch actual 3 sc_chainmak 0
ath_get_caps tx chainmask mismatch actual 3 sc_chainmak 0
Create OS_MESGQ Successfully at 0x80954070
osifp->queue_head = 0x80954370
ag7240MemInit: allocated, dmabuf=0x80660650, buffend = 80922854
Entering Task Loop
Entering WLAN event Task Loop
tpltplERROR:wireless OR ACL disable
sending message 806364d0,24
sending message 806364d0,24
TDDP: Now listening client request.
tddp is running.
httpInit: System File Registry successfully initialized.
httpInit: System File Manager successfully initialized.
httpInit: File System RPM successfully initialized.
httpInit: RPM dispatcher successfully initialized.
httpInit: MIME type guessing RPM successfully initialized.
httpInit: http Password Checking successfully initialized.
httpInit: http Access Control successfully initialized.
Software Platform for MIPS
Copyright(C) 2001-2010 by TP-LINK TECHNOLOGIES CO., LTD.
Starting WLAN !!Creation date: !! Sep7 2012, 09:41:35
# AP_STARTMODE=standard
AP_ENABLE=1
ATH_COUNTRYCODE=156
wlan_vap_create : enter. devhandle=0x80458a70, opmode=IEEE80211_M_HOSTAP, flags=0x1
wlan_vap_create : exit. devhandle=0x80458a70, opmode=IEEE80211_M_HOSTAP, flags=0x1.
osif_ioctl_create_vap: vap 0x80ffe970 vap->iv_unit 0
ieee80211_end_load: load done
ath0 end flag = 0x00028802
default
default
default
IEE80211-FREQ IOCTL vap 0x80ffe970 0,0,0
AP_CHMODE=11NGHT40PLUS
WLAN IOCTL AP_CHMODE=11NGHT40PLUS=11NGHT20=11NGHT40PLUS=1003
IEE80211-MODE IOCTL 1,11NGHT40PLUS,13
set mode 11,-2130709132,6
set mode retv 0
WLAN IOCTL AP_PRIMARY_CH=auto=6=auto=1002
IEE80211-FREQ IOCTL vap 0x80ffe970 0,0,11
WLAN IOCTL PUREG=0=0=0=1004
IEEE80211-SETPURGE IOCTL 0
WLAN IOCTL AP_HIDE_SSID=0=0=0=1005
IEEE80211-SETHIDESSIDIOCTL 0
WLAN IOCTL AP_ISOLATION=0=0=0=1034
IEE80211-setparam-nobridge 0
WLAN IOCTL AP_TX11NRATE==0x0=0x0=1041
set auto rate
WLAN IOCTL AP_11G_PROTECTION==0=0=1042
WLAN IOCTL AP_BEACON_INTERVAL=100=100=100=1043
WLAN IOCTL AP_FRAGMENT_THRESHOLD=2346=2346=2346=1044
WLAN IOCTL AP_RTS_THRESHOLD=2346=2347=2346=1046
WLAN IOCTL AP_DTIM_PERIOD=1=1=1=1045
WLAN IOCTL AP_WMM_ENABLE=1=1=1=1051
ieee80211_vap_wme_set
WLAN IOCTL AP_WMM_NOACK==0=0=1052
IOCTL set wmm noack 0
WLAN IOCTL AP_CYPHER_2==CCMP=CCMP=1000
Get EIOCGADDR
WLAN IOCTL AP_NO_EDGE_CH==0=0=1056
WLAN IOCTL AP_MCASTRATE==0=0=1018
WLAN IOCTL AP_MACFILTER_MODE==0=0=1038
WLAN IOCTL AP_MACFILTER_LIST====1000
Get EIOCGADDR
WLAN IOCTL AP_SHORT_GI=1=1=1=1055
WLAN IOCTL AP_DISABLECOEXT=1=0=1=1075
WLAN IOCTL AP_SSID=TP-LINK_4CDF18=Ath_AP123ng=TP-LINK_4CDF18=1001
IEE80211-ESSID IOCTL 1,TP-LINK_4CDF18,15
AP_CHMODE=11NGHT40PLUS
AP_CWMMODE=1
IEE80211-CWMMODE IOCTL 1
AP_AMPDU=0
AP_PURE_N=0
AP_TX_CHAINMASK=3
AP_RX_CHAINMASK=3
AP_SECMODE=None
WPS_ENABLE=1
AP_MACFILTER_MODE=0
ieee80211_open
tpltpl
WLAN IOCTL AP_BASICRATES==0=0=1039
WLAN IOCTL AP_DEBUG=0=0=0=1062
WLAN IOCTL AP_TX_POWER==0=0=1073
Starting Hostapd
AP_SSID=TP-LINK_4CDF18
AP_HOSTAPD_DEBUG=0
AP_IPADDR=192.168.1.2
AP_SECMODE=None
WPS BSS init
WPS_ENABLE=1
WPS_PIN=42383550
WPS_STATE=1
1136073605.416667: wps_led_init: LED state UNCONFIGURED
AP_SECMODE=None
WPS OPEN BSS init
starting hostapd ...
Hostapd task Created 80ffa4a0
Task details
tplAdding ath0 in bridge ...
default
Set EIOCGMIB2
default
tplEntering Hostapd Main
default
Set EIOCGMIB2
attached backend socket .
Attached backend socket for eth0
Attached backend socket for eth1
Attached backend socket for mirror 0
@@@@ kris-hostapd vapid=0 @@@@@ wiface=ath0 @@@@
**** ****
Just before eloop_run()
*** setup interface1 started **** 重要：接14楼再研究后，得到结论。。。。无需改任何电容、电阻等
841N V8的TTL正确接法是：主板上的TP1是TX，TP5是RX