lele_fj 发表于 2011-4-29 20:26

求助，cisco ap 无法正常使用！！！

借用一下别人的图片，就是这款，新手，不知道怎么弄，求助高手指导！
https://www.right.com.cn/forum/attachment.php?aid=34503&k=ec8ed14a9c7e14e958b90c36cfca0501&t=1304008070&nothumb=yes&sid=46f3EiiXHLKVTzd4Ti3E6tcorccYz9daeBj7iUhgYJvsK5k

下面是 rs 232 读取的信息。补充一下，在 倒计时 4秒 哪里按 “esc”无法停止引导，这里的 “esc”到底要如何输入啊？

POST...

Memory test                   : passed
Ethernet MAC register test    : passed
Ethernet PHY register test    : passed
Ethernet interrupt test       : passed
enet mac address
Pl










                            VxWorks System Boot


Copyright 1984-1998Wind River Systems, Inc.





CPU: AP-1200
Version: 5.4.2
BSP version: 1.0/0
Creation date: Jul 23 2003, 10:21:32



AP-1200 version 2.3.0.70



Press Esc key to stop auto-boot...
04auto-booting...

Attaching to TFFS... done.
Loading /fl/vxWorks...1482384
tarting at 0x480000...

xfffcf8 (tRootTask): bsn-i2c write retry written 0x2a read 0xff
Reading AP Configuration from the flash
enet mac address
dp0 loaded
dp83815Start
Ckeck Cable
dp0: link=down
eth0: Warning PHY setup did not complete. Check cable.
Load String = 0:0x00:0x00:0:0:0:0
Base address = 88000000, irq 3, idx = 0, devno = 0
Attach AR5212 0x13 0xe7b1e8
wlan0 revisions: mac 5.6 phy 4.1 analog 1.7 eeprom 3.4
ar0 loaded
Load String = 1:0x00:0x00:0:0:0:0
Base address = 88020000, irq 4, idx = 1, devno = 1
Attach AR5212 0x13 0xd09e98
wlan1 revisions: mac 5.6 phy 4.1 analog 1.7 eeprom 3.4
ar1 loaded
apInit: Initialize Access Point.
wlan0 added STA: 00:0b:85:01:3c:30 (8727)
wlan1 added STA: 00:0b:85:01:3c:30 (8744)
Attached TCP/IP interface to dp unit 0
Attaching interface lo0...done
Invalid device "tffs:0"

Adding 8676 symbols for standalone.


               VxWorks

Copyright 1984-1998Wind River Systems, Inc.

            CPU: AP-1200
      VxWorks: 5.4.2
    BSP version: 1.0/0
Creation date: Oct8 2006
            WDB: Ready.

Ready
0xfffcf8 (tRootTask): Can't attach unknown device mirror (unit 0).

jimm2m 发表于 2011-5-6 16:52

你进去复位了就可以用WEP进去配置了，俺都是用思科AP1231G的

lanzl 发表于 2011-5-6 20:10

这可不是ap1231g, 这是瘦ap

xtfox 发表于 2011-5-8 16:29

重灌IOS就行了

知鱼之乐 发表于 2014-10-26 18:55

jimm2m 发表于 2011-5-6 16:52
你进去复位了就可以用WEP进去配置了，俺都是用思科AP1231G的

wep怎么进去呢？

知鱼之乐 发表于 2014-10-26 18:55

jimm2m 发表于 2011-5-6 16:52
你进去复位了就可以用WEP进去配置了，俺都是用思科AP1231G的

wep怎么进去呢？
页: [1]
查看完整版本: 求助，cisco ap 无法正常使用！！！