中国移动路由器 CMCC RM2-6 刷机成砖

ZCL13951508518

米酒醉 发表于 2025-5-17 17:03
你刷了uboot？那刷错了只能上编程器了。没别的办法了。

已经上编程器了，谢谢！

ZCL13951508518

ZCL13951508518 发表于 2025-5-17 17:53
已经上编程器了，谢谢！

没有刷过UBOOT,就是刷了官方OP

米酒醉

ZCL13951508518 发表于 2025-5-17 18:00
没有刷过UBOOT,就是刷了官方OP

那就行，不客气。

ZCL13951508518

IPQ807x#
IPQ807x#
Format: Log Type - Time(microsec) - Message - Optional Info
Log Type: B - Since Boot(Power On Reset),  D - Delta,  S - Statistic
S - QC_IMAGE_VERSION_STRING=BOOT.BF.3.3.1-00147
S - IMAGE_VARIANT_STRING=HAACANAZA
S - OEM_IMAGE_VERSION_STRING=CRM
S - Boot Config, 0x000002e5
B -       201 - PBL, Start
B -      2736 - bootable_media_detect_entry, Start
B -      4213 - bootable_media_detect_success, Start
B -      4217 - elf_loader_entry, Start
B -      6880 - auth_hash_seg_entry, Start
B -      7127 - auth_hash_seg_exit, Start
B -     69236 - elf_segs_hash_verify_entry, Start
B -    131933 - PBL, End
B -    222436 - SBL1, Start
B -    303078 - GCC [RstStat:0x10, RstDbg:0x600000] WDog Stat : 0x4
B -    313143 - pm_device_init, Start
B -    498278 - PM_SET_VAL:Skip
D -    182969 - pm_device_init, Delta
B -    500535 - pm_driver_init, Start
D -      5337 - pm_driver_init, Delta
B -    507062 - clock_init, Start
D -      2104 - clock_init, Delta
B -    511027 - boot_flash_init, Start
D -     13389 - boot_flash_init, Delta
B -    528199 - boot_config_data_table_init, Start
D -      3172 - boot_config_data_table_init, Delta - (575 Bytes)
B -    535732 - Boot Setting :  0x00000618
B -    539636 - CDT version:2,Platform ID:8,Major ID:1,Minor ID:0,Subtype:10
B -    546590 - sbl1_ddr_set_params, Start
B -    550403 - CPR configuration: 0x30c
B -    553880 - cpr_init, Start
B -    556686 - Rail:0 Mode: 5 Voltage: 832000
B -    561840 - CL CPR settled at 784000mV
B -    564646 - Rail:1 Mode: 5 Voltage: 896000
B -    568825 - Rail:1 Mode: 7 Voltage: 936000
D -     16470 - cpr_init, Delta
B -    575718 - Pre_DDR_clock_init, Start
B -    579744 - Pre_DDR_clock_init, End
B -    583129 - DDR Type : PCDDR3
B -    588741 - do ddr sanity test, Start
D -      1067 - do ddr sanity test, Delta
B -    593591 - DDR: Start of HAL DDR Boot Training
B -    598257 - DDR: End of HAL DDR Boot Training
B -    604022 - DDR: Checksum to be stored on flash is 10103965
B -    614148 - Image Load, Start
D -    223839 - QSEE Image Loaded, Delta - (1373936 Bytes)
B -    838079 - Image Load, Start
D -        61 - SEC Image Loaded, Delta - (0 Bytes)
B -    845734 - Image Load, Start
D -     10706 - DEVCFG Image Loaded, Delta - (26004 Bytes)
B -    856531 - Image Load, Start
D -     25254 - RPM Image Loaded, Delta - (105964 Bytes)
B -    881846 - Image Load, Start
D -     95465 - APPSBL Image Loaded, Delta - (583860 Bytes)
B -    977433 - QSEE Execution, Start
D -        61 - QSEE Execution, Delta
B -    983228 - USB D+ check, Start
D -         0 - USB D+ check, Delta
B -    989633 - SBL1, End
D -    769515 - SBL1, Delta
S - Flash Throughput, 6736 KB/s  (2091011 Bytes,  310422 us)
S - DDR Frequency, 466 MHz
S - Core 0 Frequency, 800 MHz


U-Boot 2016.01 (Dec 24 2019 - 18:51:11 +0800)

DRAM:  smem ram ptable found: ver: 1 len: 4
512 MiB
NAND:  ONFI device found
ID = 1590aa2c
Vendor = 2c
Device = aa
qpic_nand: changing oobsize to 80 from 128 bytes
SF: Unsupported flash IDs: manuf ff, jedec ffff, ext_jedec ffff
ipq_spi: SPI Flash not found (bus/cs/speed/mode) = (0/0/48000000/0)
256 MiB
MMC:   sdhci: Node Not found, skipping initialization

*** Warning - bad CRC, using default environment

PCI1 is not defined in the device tree
In:    serial@78B3000
Out:   serial@78B3000
Err:   serial@78B3000
machid: 801000a
MMC Device 0 not found
eth5 MAC Address from ART is not valid
Hit any key to stop autoboot:  0
ubi0: attaching mtd1
ubi0: scanning is finished
ubi0: attached mtd1 (name "mtd=0", size 46 MiB)
ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096
ubi0: good PEBs: 368, bad PEBs: 0, corrupted PEBs: 0
ubi0: user volume: 2, internal volumes: 1, max. volumes count: 128
ubi0: max/mean erase counter: 5/2, WL threshold: 4096, image sequence number: 1574188133
ubi0: available PEBs: 0, total reserved PEBs: 368, PEBs reserved for bad PEB handling: 40
Read 0 bytes from volume kernel to 44000000
No size specified -> Using max size (13713408)
Could not find PCI in device tree
Config not availabale

Net:   MAC0 addr:f8:48:fd:fc:5a:e1
PHY ID1: 0x4d
PHY ID2: 0xd0b1
EDMA ver 1 hw init
Num rings - TxDesc:1 (0-0) TxCmpl:1 (7-7)
RxDesc:1 (15-15) RxFill:1 (7-7)
ipq807x_edma_alloc_rings: successfull
ipq807x_edma_setup_ring_resources: successfull
ipq807x_edma_configure_rings: successfull
ipq807x_edma_hw_init: successfull
eth0

Net:   MAC0 addr:f8:48:fd:fc:5a:e1
EDMA ver 1 hw init
Num rings - TxDesc:1 (0-0) TxCmpl:1 (7-7)
RxDesc:1 (15-15) RxFill:1 (7-7)
ipq807x_edma_alloc_rings: successfull
ipq807x_edma_setup_ring_resources: successfull
ipq807x_edma_configure_rings: successfull
ipq807x_edma_hw_init: successfull
, eth0
Warning: eth0 MAC addresses don't match:
Address in SROM is         f8:48:fd:fc:5a:e1
Address in environment is  f8:48:fd:fc:5a:e0

IPQ807x# help
?       - alias for 'help'
aq_load_fw- LOAD aq-fw-binary
aq_phy_restart- Restart Aquantia phy
base    - print or set address offset
bdinfo  - print Board Info structure
bootipq - bootipq from flash device
bootm   - boot application image from memory
bootp   - boot image via network using BOOTP/TFTP protocol
bootz   - boot Linux zImage image from memory
chpart  - change active partition
cmp     - memory compare
cp      - memory copy
crc32   - checksum calculation
dcache  - enable or disable data cache
dhcp    - boot image via network using DHCP/TFTP protocol
dm      - Driver model low level access
echo    - echo args to console
env     - environment handling commands
erase   - erase FLASH memory
exectzt - execute TZT

exit    - exit script
false   - do nothing, unsuccessfully
fdt     - flattened device tree utility commands
flash   - flash part_name
        flash part_name load_addr file_size

flasherase- flerase part_name

flinfo  - print FLASH memory information
fuseipq - fuse QFPROM registers from memory

go      - start application at address 'addr'
help    - print command description/usage
i2c     - I2C sub-system
icache  - enable or disable instruction cache
imxtract- extract a part of a multi-image
ipq_mdio- IPQ mdio utility commands
is_sec_boot_enabled- check secure boot fuse is enabled or not

itest   - return true/false on integer compare
loop    - infinite loop on address range
md      - memory display
mii     - MII utility commands
mm      - memory modify (auto-incrementing address)
mmc     - MMC sub system
mmcinfo - display MMC info
mtdparts- define flash/nand partitions
mtest   - simple RAM read/write test
mw      - memory write (fill)
nand    - NAND sub-system
nboot   - boot from NAND device
nm      - memory modify (constant address)
pci     - list and access PCI Configuration Space
ping    - send ICMP ECHO_REQUEST to network host
printenv- print environment variables
protect - enable or disable FLASH write protection
reset   - Perform RESET of the CPU
run     - run commands in an environment variable
runmulticore- Enable and schedule secondary cores
saveenv - save environment variables to persistent storage
secure_authenticate- authenticate the signed image

setenv  - set environment variables
sf      - SPI flash sub-system
showvar - print local hushshell variables
sleep   - delay execution for some time
smeminfo- print SMEM FLASH information
source  - run script from memory
test    - minimal test like /bin/sh
tftpboot- boot image via network using TFTP protocol
tftpput - TFTP put command, for uploading files to a server
true    - do nothing, successfully
uart    - UART sub-system
ubi     - ubi commands
usb     - USB sub-system
usbboot - boot from USB device
version - print monitor, compiler and linker version
IPQ807x# tftpboot
ipq807x_eth_halt: done
eth0 PHY0 Down Speed :10 Half duplex
eth0 PHY1 Down Speed :10 Half duplex
eth0 PHY2 Down Speed :10 Half duplex
eth0 PHY3 up Speed :1000 Full duplex
eth0 PHY4 up Speed :1000 Full duplex
eth0 PHY5 up Speed :1000 Full duplex
ipq807x_eth_init: done
*** Warning: no boot file name; using 'C0A80A0A.img'
Using eth0 device
TFTP from server 192.168.10.1; our IP address is 192.168.10.10
Filename 'C0A80A0A.img'.
Load address: 0x44000000
Loading: *
TFTP error: 'File not found' (1)
Not retrying...
ipq807x_eth_halt: done
ipq807x_eth_halt: done
IPQ807x#

ZCL13951508518

连不上呢？

ZCL13951508518

IPQ807x# help
?       - alias for 'help'
aq_load_fw- LOAD aq-fw-binary
aq_phy_restart- Restart Aquantia phy
base    - print or set address offset
bdinfo  - print Board Info structure
bootipq - bootipq from flash device
bootm   - boot application image from memory
bootp   - boot image via network using BOOTP/TFTP protocol
bootz   - boot Linux zImage image from memory
chpart  - change active partition
cmp     - memory compare
cp      - memory copy
crc32   - checksum calculation
dcache  - enable or disable data cache
dhcp    - boot image via network using DHCP/TFTP protocol
dm      - Driver model low level access
echo    - echo args to console
env     - environment handling commands
erase   - erase FLASH memory
exectzt - execute TZT

exit    - exit script
false   - do nothing, unsuccessfully
fdt     - flattened device tree utility commands
flash   - flash part_name
        flash part_name load_addr file_size

flasherase- flerase part_name

flinfo  - print FLASH memory information
fuseipq - fuse QFPROM registers from memory

go      - start application at address 'addr'
help    - print command description/usage
i2c     - I2C sub-system
icache  - enable or disable instruction cache
imxtract- extract a part of a multi-image
ipq_mdio- IPQ mdio utility commands
is_sec_boot_enabled- check secure boot fuse is enabled or not

itest   - return true/false on integer compare
loop    - infinite loop on address range
md      - memory display
mii     - MII utility commands
mm      - memory modify (auto-incrementing address)
mmc     - MMC sub system
mmcinfo - display MMC info
mtdparts- define flash/nand partitions
mtest   - simple RAM read/write test
mw      - memory write (fill)
nand    - NAND sub-system
nboot   - boot from NAND device
nm      - memory modify (constant address)
pci     - list and access PCI Configuration Space
ping    - send ICMP ECHO_REQUEST to network host
printenv- print environment variables
protect - enable or disable FLASH write protection
reset   - Perform RESET of the CPU
run     - run commands in an environment variable
runmulticore- Enable and schedule secondary cores
saveenv - save environment variables to persistent storage
secure_authenticate- authenticate the signed image

setenv  - set environment variables
sf      - SPI flash sub-system
showvar - print local hushshell variables
sleep   - delay execution for some time
smeminfo- print SMEM FLASH information
source  - run script from memory
test    - minimal test like /bin/sh
tftpboot- boot image via network using TFTP protocol
tftpput - TFTP put command, for uploading files to a server
true    - do nothing, successfully
uart    - UART sub-system
ubi     - ubi commands
usb     - USB sub-system
usbboot - boot from USB device
version - print monitor, compiler and linker version
IPQ807x# reset
resetting ...

Format: Log Type - Time(microsec) - Message - Optional Info
Log Type: B - Since Boot(Power On Reset),  D - Delta,  S - Statistic
S - QC_IMAGE_VERSION_STRING=BOOT.BF.3.3.1-00147
S - IMAGE_VARIANT_STRING=HAACANAZA
S - OEM_IMAGE_VERSION_STRING=CRM
S - Boot Config, 0x000002e5
B -       203 - PBL, Start
B -      2739 - bootable_media_detect_entry, Start
B -      4218 - bootable_media_detect_success, Start
B -      4222 - elf_loader_entry, Start
B -      6892 - auth_hash_seg_entry, Start
B -      7139 - auth_hash_seg_exit, Start
B -     69384 - elf_segs_hash_verify_entry, Start
B -    132079 - PBL, End
B -    221735 - SBL1, Start
B -    302072 - GCC [RstStat:0x10, RstDbg:0x600000] WDog Stat : 0x4
B -    312076 - pm_device_init, Start
B -    497516 - PM_SET_VAL:Skip
D -    183305 - pm_device_init, Delta
B -    499803 - pm_driver_init, Start
D -      5368 - pm_driver_init, Delta
B -    506269 - clock_init, Start
D -      2135 - clock_init, Delta
B -    510326 - boot_flash_init, Start
D -     13389 - boot_flash_init, Delta
B -    527406 - boot_config_data_table_init, Start
D -      3172 - boot_config_data_table_init, Delta - (575 Bytes)
B -    534939 - Boot Setting :  0x00000618
B -    538874 - CDT version:2,Platform ID:8,Major ID:1,Minor ID:0,Subtype:10
B -    545797 - sbl1_ddr_set_params, Start
B -    549640 - CPR configuration: 0x30c
B -    553026 - cpr_init, Start
B -    555893 - Rail:0 Mode: 5 Voltage: 832000
B -    561047 - CL CPR settled at 784000mV
B -    563853 - Rail:1 Mode: 5 Voltage: 896000
B -    568062 - Rail:1 Mode: 7 Voltage: 936000
D -     16439 - cpr_init, Delta
B -    574925 - Pre_DDR_clock_init, Start
B -    578951 - Pre_DDR_clock_init, End
B -    582336 - DDR Type : PCDDR3
B -    587979 - do ddr sanity test, Start
D -      1067 - do ddr sanity test, Delta
B -    592828 - DDR: Start of HAL DDR Boot Training
B -    597464 - DDR: End of HAL DDR Boot Training
B -    603229 - DDR: Checksum to be stored on flash is 10103965
B -    613385 - Image Load, Start
D -    223809 - QSEE Image Loaded, Delta - (1373936 Bytes)
B -    837286 - Image Load, Start
D -        61 - SEC Image Loaded, Delta - (0 Bytes)
B -    844972 - Image Load, Start
D -     10705 - DEVCFG Image Loaded, Delta - (26004 Bytes)
B -    855769 - Image Load, Start
D -     25223 - RPM Image Loaded, Delta - (105964 Bytes)
B -    881084 - Image Load, Start
D -     95434 - APPSBL Image Loaded, Delta - (583860 Bytes)
B -    976640 - QSEE Execution, Start
D -        91 - QSEE Execution, Delta
B -    982435 - USB D+ check, Start
D -        30 - USB D+ check, Delta
B -    988840 - SBL1, End
D -    769393 - SBL1, Delta
S - Flash Throughput, 6738 KB/s  (2091011 Bytes,  310330 us)
S - DDR Frequency, 466 MHz
S - Core 0 Frequency, 800 MHz


U-Boot 2016.01 (Dec 24 2019 - 18:51:11 +0800)

DRAM:  smem ram ptable found: ver: 1 len: 4
512 MiB
NAND:  ONFI device found
ID = 1590aa2c
Vendor = 2c
Device = aa
qpic_nand: changing oobsize to 80 from 128 bytes
SF: Unsupported flash IDs: manuf ff, jedec ffff, ext_jedec ffff
ipq_spi: SPI Flash not found (bus/cs/speed/mode) = (0/0/48000000/0)
256 MiB
MMC:   sdhci: Node Not found, skipping initialization

*** Warning - bad CRC, using default environment

PCI1 is not defined in the device tree
In:    serial@78B3000
Out:   serial@78B3000
Err:   serial@78B3000
machid: 801000a
MMC Device 0 not found
eth5 MAC Address from ART is not valid
Hit any key to stop autoboot:  0
ubi0: attaching mtd1
ubi0: scanning is finished
ubi0: attached mtd1 (name "mtd=0", size 46 MiB)
ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096
ubi0: good PEBs: 368, bad PEBs: 0, corrupted PEBs: 0
ubi0: user volume: 2, internal volumes: 1, max. volumes count: 128
ubi0: max/mean erase counter: 5/2, WL threshold: 4096, image sequence number: 1574188133
ubi0: available PEBs: 0, total reserved PEBs: 368, PEBs reserved for bad PEB handling: 40
Read 0 bytes from volume kernel to 44000000
No size specified -> Using max size (13713408)
Could not find PCI in device tree
Config not availabale

Net:   MAC0 addr:f8:48:fd:fc:5a:e1
PHY ID1: 0x4d
PHY ID2: 0xd0b1
EDMA ver 1 hw init
Num rings - TxDesc:1 (0-0) TxCmpl:1 (7-7)
RxDesc:1 (15-15) RxFill:1 (7-7)
ipq807x_edma_alloc_rings: successfull
ipq807x_edma_setup_ring_resources: successfull
ipq807x_edma_configure_rings: successfull
ipq807x_edma_hw_init: successfull
eth0

Net:   MAC0 addr:f8:48:fd:fc:5a:e1
EDMA ver 1 hw init
Num rings - TxDesc:1 (0-0) TxCmpl:1 (7-7)
RxDesc:1 (15-15) RxFill:1 (7-7)
ipq807x_edma_alloc_rings: successfull
ipq807x_edma_setup_ring_resources: successfull
ipq807x_edma_configure_rings: successfull
ipq807x_edma_hw_init: successfull
, eth0
Warning: eth0 MAC addresses don't match:
Address in SROM is         f8:48:fd:fc:5a:e1
Address in environment is  f8:48:fd:fc:5a:e0

IPQ807x# help
?       - alias for 'help'
aq_load_fw- LOAD aq-fw-binary
aq_phy_restart- Restart Aquantia phy
base    - print or set address offset
bdinfo  - print Board Info structure
bootipq - bootipq from flash device
bootm   - boot application image from memory
bootp   - boot image via network using BOOTP/TFTP protocol
bootz   - boot Linux zImage image from memory
chpart  - change active partition
cmp     - memory compare
cp      - memory copy
crc32   - checksum calculation
dcache  - enable or disable data cache
dhcp    - boot image via network using DHCP/TFTP protocol
dm      - Driver model low level access
echo    - echo args to console
env     - environment handling commands
erase   - erase FLASH memory
exectzt - execute TZT

exit    - exit script
false   - do nothing, unsuccessfully
fdt     - flattened device tree utility commands
flash   - flash part_name
        flash part_name load_addr file_size

flasherase- flerase part_name

flinfo  - print FLASH memory information
fuseipq - fuse QFPROM registers from memory

go      - start application at address 'addr'
help    - print command description/usage
i2c     - I2C sub-system
icache  - enable or disable instruction cache
imxtract- extract a part of a multi-image
ipq_mdio- IPQ mdio utility commands
is_sec_boot_enabled- check secure boot fuse is enabled or not

itest   - return true/false on integer compare
loop    - infinite loop on address range
md      - memory display
mii     - MII utility commands
mm      - memory modify (auto-incrementing address)
mmc     - MMC sub system
mmcinfo - display MMC info
mtdparts- define flash/nand partitions
mtest   - simple RAM read/write test
mw      - memory write (fill)
nand    - NAND sub-system
nboot   - boot from NAND device
nm      - memory modify (constant address)
pci     - list and access PCI Configuration Space
ping    - send ICMP ECHO_REQUEST to network host
printenv- print environment variables
protect - enable or disable FLASH write protection
reset   - Perform RESET of the CPU
run     - run commands in an environment variable
runmulticore- Enable and schedule secondary cores
saveenv - save environment variables to persistent storage
secure_authenticate- authenticate the signed image

setenv  - set environment variables
sf      - SPI flash sub-system
showvar - print local hushshell variables
sleep   - delay execution for some time
smeminfo- print SMEM FLASH information
source  - run script from memory
test    - minimal test like /bin/sh
tftpboot- boot image via network using TFTP protocol
tftpput - TFTP put command, for uploading files to a server
true    - do nothing, successfully
uart    - UART sub-system
ubi     - ubi commands
usb     - USB sub-system
usbboot - boot from USB device
version - print monitor, compiler and linker version
IPQ807x#

米酒醉

ZCL13951508518 发表于 2025-5-18 16:02
IPQ807x# help
?       - alias for 'help'
aq_load_fw- LOAD aq-fw-binary

*** Warning: no boot file name; using 'C0A80A0A.img'
没有刷对固件，无法引导启动系统。

ZCL13951508518

米酒醉 发表于 2025-5-18 22:04
*** Warning: no boot file name; using 'C0A80A0A.img'
没有刷对固件，无法引导启动系统。 ...

TFTP连不上，没办法刷其它固件了。

米酒醉

ZCL13951508518 发表于 2025-5-18 13:23
IPQ807x#
IPQ807x#
Format: Log Type - Time(microsec) - Message - Optional Info

printenv命令查看是否有serverip？
如果没有请执行：
setenv serverip xxx.xxx.xxx.xxx
saveenv
再次尝试tftp刷机。

ZCL13951508518

米酒醉 发表于 2025-5-19 21:53
printenv命令查看是否有serverip？
如果没有请执行：
setenv serverip xxx.xxx.xxx.xxx

谢谢！

ZCL13951508518

ZCL13951508518 发表于 2025-5-19 22:16
谢谢！

就是连不上网络，也ping不通。

ZCL13951508518

ZCL13951508518 发表于 2025-5-18 16:02
IPQ807x# help
?       - alias for 'help'
aq_load_fw- LOAD aq-fw-binary

Format: Log Type - Time(microsec) - Message - Optional Info
Log Type: B - Since Boot(Power On Reset),  D - Delta,  S - Statistic
S - QC_IMAGE_VERSION_STRING=BOOT.BF.3.3.1-00147
S - IMAGE_VARIANT_STRING=HAACANAZA
S - OEM_IMAGE_VERSION_STRING=CRM
S - Boot Config, 0x000002e5
B -       201 - PBL, Start
B -      2734 - bootable_media_detect_entry, Start
B -      4210 - bootable_media_detect_success, Start
B -      4214 - elf_loader_entry, Start
B -      6877 - auth_hash_seg_entry, Start
B -      7124 - auth_hash_seg_exit, Start
B -     69232 - elf_segs_hash_verify_entry, Start
B -    131929 - PBL, End
B -    222955 - SBL1, Start
B -    303810 - GCC [RstStat:0x10, RstDbg:0x600000] WDog Stat : 0x4
B -    313875 - pm_device_init, Start
B -    499407 - PM_SET_VAL:Skip
D -    183335 - pm_device_init, Delta
B -    501664 - pm_driver_init, Start
D -      5337 - pm_driver_init, Delta
B -    508191 - clock_init, Start
D -      2104 - clock_init, Delta
B -    512156 - boot_flash_init, Start
D -     13389 - boot_flash_init, Delta
B -    529327 - boot_config_data_table_init, Start
D -      3172 - boot_config_data_table_init, Delta - (575 Bytes)
B -    536861 - Boot Setting :  0x00000618
B -    540795 - CDT version:2,Platform ID:8,Major ID:1,Minor ID:0,Subtype:10
B -    547719 - sbl1_ddr_set_params, Start
B -    551562 - CPR configuration: 0x30c
B -    554947 - cpr_init, Start
B -    557814 - Rail:0 Mode: 5 Voltage: 832000
B -    562969 - CL CPR settled at 784000mV
B -    565775 - Rail:1 Mode: 5 Voltage: 896000
B -    569984 - Rail:1 Mode: 7 Voltage: 936000
D -     16439 - cpr_init, Delta
B -    576846 - Pre_DDR_clock_init, Start
B -    580872 - Pre_DDR_clock_init, End
B -    584258 - DDR Type : PCDDR3
B -    589900 - do ddr sanity test, Start
D -      1067 - do ddr sanity test, Delta
B -    594750 - DDR: Start of HAL DDR Boot Training
B -    599386 - DDR: End of HAL DDR Boot Training
B -    605150 - DDR: Checksum to be stored on flash is 10103965
B -    615276 - Image Load, Start
D -    223809 - QSEE Image Loaded, Delta - (1373936 Bytes)
B -    839177 - Image Load, Start
D -        61 - SEC Image Loaded, Delta - (0 Bytes)
B -    846863 - Image Load, Start
D -     10705 - DEVCFG Image Loaded, Delta - (26004 Bytes)
B -    857660 - Image Load, Start
D -     25223 - RPM Image Loaded, Delta - (105964 Bytes)
B -    882975 - Image Load, Start
D -     95465 - APPSBL Image Loaded, Delta - (583860 Bytes)
B -    978562 - QSEE Execution, Start
D -        61 - QSEE Execution, Delta
B -    984357 - USB D+ check, Start
D -         0 - USB D+ check, Delta
B -    990762 - SBL1, End
D -    770125 - SBL1, Delta
S - Flash Throughput, 6734 KB/s  (2091011 Bytes,  310513 us)
S - DDR Frequency, 466 MHz
S - Core 0 Frequency, 800 MHz


U-Boot 2016.01 (Dec 24 2019 - 18:51:11 +0800)

DRAM:  smem ram ptable found: ver: 1 len: 4
512 MiB
NAND:  ONFI device found
ID = 1590aa2c
Vendor = 2c
Device = aa
qpic_nand: changing oobsize to 80 from 128 bytes
SF: Unsupported flash IDs: manuf ff, jedec ffff, ext_jedec ffff
ipq_spi: SPI Flash not found (bus/cs/speed/mode) = (0/0/48000000/0)
256 MiB
MMC:   sdhci: Node Not found, skipping initialization

*** Warning - bad CRC, using default environment

PCI1 is not defined in the device tree
In:    serial@78B3000
Out:   serial@78B3000
Err:   serial@78B3000
machid: 801000a
MMC Device 0 not found
eth5 MAC Address from ART is not valid
Hit any key to stop autoboot:  0
ubi0: attaching mtd1
ubi0: scanning is finished
ubi0: attached mtd1 (name "mtd=0", size 46 MiB)
ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096
ubi0: good PEBs: 368, bad PEBs: 0, corrupted PEBs: 0
ubi0: user volume: 2, internal volumes: 1, max. volumes count: 128
ubi0: max/mean erase counter: 5/2, WL threshold: 4096, image sequence number: 1574188133
ubi0: available PEBs: 0, total reserved PEBs: 368, PEBs reserved for bad PEB handling: 40
Read 0 bytes from volume kernel to 44000000
No size specified -> Using max size (13713408)
Could not find PCI in device tree
Config not availabale

Net:   MAC0 addr:f8:48:fd:fc:5a:e1
PHY ID1: 0x4d
PHY ID2: 0xd0b1
EDMA ver 1 hw init
Num rings - TxDesc:1 (0-0) TxCmpl:1 (7-7)
RxDesc:1 (15-15) RxFill:1 (7-7)
ipq807x_edma_alloc_rings: successfull
ipq807x_edma_setup_ring_resources: successfull
ipq807x_edma_configure_rings: successfull
ipq807x_edma_hw_init: successfull
eth0

Net:   MAC0 addr:f8:48:fd:fc:5a:e1
EDMA ver 1 hw init
Num rings - TxDesc:1 (0-0) TxCmpl:1 (7-7)
RxDesc:1 (15-15) RxFill:1 (7-7)
ipq807x_edma_alloc_rings: successfull
ipq807x_edma_setup_ring_resources: successfull
ipq807x_edma_configure_rings: successfull
ipq807x_edma_hw_init: successfull
, eth0
Warning: eth0 MAC addresses don't match:
Address in SROM is         f8:48:fd:fc:5a:e1
Address in environment is  f8:48:fd:fc:5a:e0

IPQ807x# reset
resetting ...

Format: Log Type - Time(microsec) - Message - Optional Info
Log Type: B - Since Boot(Power On Reset),  D - Delta,  S - Statistic
S - QC_IMAGE_VERSION_STRING=BOOT.BF.3.3.1-00147
S - IMAGE_VARIANT_STRING=HAACANAZA
S - OEM_IMAGE_VERSION_STRING=CRM
S - Boot Config, 0x000002e5
B -       201 - PBL, Start
B -      2736 - bootable_media_detect_entry, Start
B -      4215 - bootable_media_detect_success, Start
B -      4219 - elf_loader_entry, Start
B -      6888 - auth_hash_seg_entry, Start
B -      7137 - auth_hash_seg_exit, Start
B -     69382 - elf_segs_hash_verify_entry, Start
B -    132079 - PBL, End
B -    223931 - SBL1, Start
B -    305061 - GCC [RstStat:0x10, RstDbg:0x600000] WDog Stat : 0x4
B -    315156 - pm_device_init, Start
B -    502335 - PM_SET_VAL:Skip
D -    185013 - pm_device_init, Delta
B -    504622 - pm_driver_init, Start
D -      5368 - pm_driver_init, Delta
B -    511088 - clock_init, Start
D -      2135 - clock_init, Delta
B -    515145 - boot_flash_init, Start
D -     13389 - boot_flash_init, Delta
B -    532225 - boot_config_data_table_init, Start
D -      3202 - boot_config_data_table_init, Delta - (575 Bytes)
B -    539758 - Boot Setting :  0x00000618
B -    543693 - CDT version:2,Platform ID:8,Major ID:1,Minor ID:0,Subtype:10
B -    550616 - sbl1_ddr_set_params, Start
B -    554429 - CPR configuration: 0x30c
B -    557906 - cpr_init, Start
B -    560712 - Rail:0 Mode: 5 Voltage: 832000
B -    565836 - CL CPR settled at 784000mV
B -    568672 - Rail:1 Mode: 5 Voltage: 896000
B -    572942 - Rail:1 Mode: 7 Voltage: 936000
D -     16470 - cpr_init, Delta
B -    579744 - Pre_DDR_clock_init, Start
B -    583770 - Pre_DDR_clock_init, End
B -    587155 - DDR Type : PCDDR3
B -    592828 - do ddr sanity test, Start
D -      1067 - do ddr sanity test, Delta
B -    597586 - DDR: Start of HAL DDR Boot Training
B -    602344 - DDR: End of HAL DDR Boot Training
B -    608017 - DDR: Checksum to be stored on flash is 10103965
B -    618235 - Image Load, Start
D -    223809 - QSEE Image Loaded, Delta - (1373936 Bytes)
B -    842135 - Image Load, Start
D -        61 - SEC Image Loaded, Delta - (0 Bytes)
B -    849821 - Image Load, Start
D -     10706 - DEVCFG Image Loaded, Delta - (26004 Bytes)
B -    860618 - Image Load, Start
D -     25224 - RPM Image Loaded, Delta - (105964 Bytes)
B -    885933 - Image Load, Start
D -     95435 - APPSBL Image Loaded, Delta - (583860 Bytes)
B -    981490 - QSEE Execution, Start
D -        61 - QSEE Execution, Delta
B -    987315 - USB D+ check, Start
D -         0 - USB D+ check, Delta
B -    993690 - SBL1, End
D -    772077 - SBL1, Delta
S - Flash Throughput, 6734 KB/s  (2091011 Bytes,  310485 us)
S - DDR Frequency, 466 MHz
S - Core 0 Frequency, 800 MHz


U-Boot 2016.01 (Dec 24 2019 - 18:51:11 +0800)

DRAM:  smem ram ptable found: ver: 1 len: 4
512 MiB
NAND:  ONFI device found
ID = 1590aa2c
Vendor = 2c
Device = aa
qpic_nand: changing oobsize to 80 from 128 bytes
SF: Unsupported flash IDs: manuf ff, jedec ffff, ext_jedec ffff
ipq_spi: SPI Flash not found (bus/cs/speed/mode) = (0/0/48000000/0)
256 MiB
MMC:   sdhci: Node Not found, skipping initialization

*** Warning - bad CRC, using default environment

PCI1 is not defined in the device tree
In:    serial@78B3000
Out:   serial@78B3000
Err:   serial@78B3000
machid: 801000a
MMC Device 0 not found
eth5 MAC Address from ART is not valid
Hit any key to stop autoboot:  0
ubi0: attaching mtd1
ubi0: scanning is finished
ubi0: attached mtd1 (name "mtd=0", size 46 MiB)
ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096
ubi0: good PEBs: 368, bad PEBs: 0, corrupted PEBs: 0
ubi0: user volume: 2, internal volumes: 1, max. volumes count: 128
ubi0: max/mean erase counter: 5/2, WL threshold: 4096, image sequence number: 1574188133
ubi0: available PEBs: 0, total reserved PEBs: 368, PEBs reserved for bad PEB handling: 40
Read 0 bytes from volume kernel to 44000000
No size specified -> Using max size (13713408)
Could not find PCI in device tree
Config not availabale

Net:   MAC0 addr:f8:48:fd:fc:5a:e1
PHY ID1: 0x4d
PHY ID2: 0xd0b1
EDMA ver 1 hw init
Num rings - TxDesc:1 (0-0) TxCmpl:1 (7-7)
RxDesc:1 (15-15) RxFill:1 (7-7)
ipq807x_edma_alloc_rings: successfull
ipq807x_edma_setup_ring_resources: successfull
ipq807x_edma_configure_rings: successfull
ipq807x_edma_hw_init: successfull
eth0

Net:   MAC0 addr:f8:48:fd:fc:5a:e1
EDMA ver 1 hw init
Num rings - TxDesc:1 (0-0) TxCmpl:1 (7-7)
RxDesc:1 (15-15) RxFill:1 (7-7)
ipq807x_edma_alloc_rings: successfull
ipq807x_edma_setup_ring_resources: successfull
ipq807x_edma_configure_rings: successfull
ipq807x_edma_hw_init: successfull
, eth0
Warning: eth0 MAC addresses don't match:
Address in SROM is         f8:48:fd:fc:5a:e1
Address in environment is  f8:48:fd:fc:5a:e0

IPQ807x#

ZCL13951508518

ZCL13951508518 发表于 2025-6-4 20:48
Format: Log Type - Time(microsec) - Message - Optional Info
Log Type: B - Since Boot(Power On Rese ...

不知道怎么进UBOOT