[2019-03-05]改华硕[N14U N54U]5G 2G的7620老毛子Padavan固件(私人云储存 aria2 QOS)

lei***

再问一个问题，楼主怎么检测pdnsd+chinadns运行了？
看日志还是？
如果是日志什么样的日志就是成功了的标志，小白不懂。谢谢啦

玉树***

很多附加功能都是脚本命令实现的，如果觉得启用功能太多导致不稳定，可以不启用附加功能，这样就是原版固件了，也可以清空脚本。
长长的脚本看着头大，不知道启用Entware后安装Luci管理界面到U盘，再改一下80端口，这样就相当于加了OpenWRT系统了，安装管理软件方便些，不知是否可行。

axi***

hiboyhiboyhiboy 发表于 2015-12-1 11:23
是的，网页按钮等于启动对应脚本。

如果你设置实体按钮运行脚本也能执行脚本。

很好的设计，赞！这几日正在看剧，开启Adbybys,没有了不想看的内容真好。
今天开了Adbybylock,没有了不想关心的人的绯闻，太好了。

jn_c***

今天刚更新了。 这样的环境：硬件 newifi mini ，breed 791，固件 3.4.3.9-097-12-1。

在 breed 里面重启，或者 固件里面重启(路由器设置（NVRAM）回复出厂) 会导致路由器无限重启。只能断电插电源，才能正常启动起来。

------------------------------------------------

直接用 页面 右上角 的 重启 按钮 重启，则 路由器 重启后死机。

woai***

楼主你屌爆了。。。真牛逼，来膜拜一下

hiboyhi***

jn_child 发表于 2015-12-1 13:56
今天刚更新了。 这样的环境：硬件 newifi mini ，breed 791，固件 3.4.3.9-097-12-1。

在 breed 里面重 ...

一样是y1，breed777，没出现这样的情况。
换回breed777，再刷入试试吧

an***

换了32位Ubuntu还是会报错，用汉化文件覆盖了源码，是这里的问题吗？还是config配置出问题了？

1. ### Target Vendor/Product (support only Ralink RT3883/MT7620/MT7621)
   
2. CONFIG_VENDOR=Ralink
   
3. #CONFIG_PRODUCT=RT3883
   
4. CONFIG_PRODUCT=MT7620
   
5. 
   
6. ### Target ProductID (board select, max 12 symbols)
   
7. #CONFIG_FIRMWARE_PRODUCT_ID="RT-N14U"
   
8. #CONFIG_FIRMWARE_PRODUCT_ID="RT-N56U"
   
9. #CONFIG_FIRMWARE_PRODUCT_ID="RT-N65U"
   
10. #CONFIG_FIRMWARE_PRODUCT_ID="SWR1100"
    
11. #CONFIG_FIRMWARE_PRODUCT_ID="BN750DB"
    
12. CONFIG_FIRMWARE_PRODUCT_ID="NHNS"
    
13. 
    
14. ### Linux kernel and toolchain (only linux-3.0.x for "RT-N65U" target yet)
    
15. #CONFIG_LINUXDIR=linux-3.0.x
    
16. CONFIG_LINUXDIR=linux-3.4.x
    
17. CONFIG_TOOLCHAIN_DIR=/home/ano/rlab/ftmp/toolchain-mipsel
    
18. 
    
19. ############################################################
    
20. ### Linux kernel configuration
    
21. ############################################################
    
22. 
    
23. ### Build ROOTFS_IN_RAM firmware mode (kernel+initramfs).
    
24. ### Decreased firmware size, but more RAM used, slow boot.
    
25. ### Also allow build image for load w/o flash from UART console
    
26. #CONFIG_FIRMWARE_TYPE_ROOTFS_IN_RAM=y
    
27. 
    
28. ### Kernel driver select for WiFi AP 5GHz
    
29. ### 2.4 = RT3883/3662 v2.4.3.6
    
30. ### 2.7 = RT3883/3662 v2.7.2.0
    
31. CONFIG_FIRMWARE_WIFI5_DRIVER=2.7
    
32. 
    
33. ### Kernel driver select for WiFi AP 2.4GHz
    
34. ### 2.4 = RT3092 v2.4.0.5
    
35. ### 2.5 = RT3092 v2.5.0.11
    
36. ### 2.7 = RT3092 v2.7.1.5
    
37. CONFIG_FIRMWARE_WIFI2_DRIVER=2.7
    
38. 
    
39. ### Enable IPv6 support
    
40. CONFIG_FIRMWARE_ENABLE_IPV6=y
    
41. 
    
42. ### Enable USB support
    
43. CONFIG_FIRMWARE_ENABLE_USB=y
    
44. 
    
45. ### Enable NTFS filesystem support via Paragon "ufsd" driver. ~0.4MB
    
46. CONFIG_FIRMWARE_ENABLE_UFSD=y
    
47. 
    
48. ### Enable FAT/FAT32 filesystem support. ~0.1MB
    
49. CONFIG_FIRMWARE_ENABLE_FAT=y
    
50. 
    
51. ### Enable exFAT (FAT/FAT32 too) filesystem support. ~0.12MB
    
52. CONFIG_FIRMWARE_ENABLE_EXFAT=y
    
53. 
    
54. ### Enable EXT2 filesystem support. ~0.1MB
    
55. #CONFIG_FIRMWARE_ENABLE_EXT2=y
    
56. 
    
57. ### Enable EXT3 filesystem support. ~0.2MB
    
58. #CONFIG_FIRMWARE_ENABLE_EXT3=y
    
59. 
    
60. ### Enable EXT4 (EXT3/2 too) filesystem support. ~0.4MB
    
61. #CONFIG_FIRMWARE_ENABLE_EXT4=y
    
62. 
    
63. ### Enable XFS filesystem support. ~0.6MB
    
64. #CONFIG_FIRMWARE_ENABLE_XFS=y
    
65. 
    
66. ### Enable FUSE (filesystems in userspace) support. ~0.1MB
    
67. CONFIG_FIRMWARE_ENABLE_FUSE=y
    
68. 
    
69. ### Enable swap files/partitions support. ~0.05MB
    
70. #CONFIG_FIRMWARE_ENABLE_SWAP=y
    
71. 
    
72. ### Include UVC camera modules. ~0.2MB
    
73. #CONFIG_FIRMWARE_INCLUDE_UVC=y
    
74. 
    
75. ### Include USB-HID modules. ~0.2MB
    
76. #CONFIG_FIRMWARE_INCLUDE_HID=y
    
77. 
    
78. ### Include USB-Serial modules (e.g. pl2303). ~0.03MB
    
79. #CONFIG_FIRMWARE_INCLUDE_SERIAL=y
    
80. 
    
81. ### Include network QoS scheduling modules. ~0.2MB
    
82. #CONFIG_FIRMWARE_INCLUDE_QOS=y
    
83. 
    
84. ### Include IMQ module for shapers (a bit of performance degradation). ~0.02MB
    
85. #CONFIG_FIRMWARE_INCLUDE_IMQ=y
    
86. 
    
87. ### Include IFB module for shapers. ~0.03MB
    
88. #CONFIG_FIRMWARE_INCLUDE_IFB=y
    
89. 
    
90. ### Include IPSet utility and kernel modules. ~0.4MB
    
91. CONFIG_FIRMWARE_INCLUDE_IPSET=y
    
92. 
    
93. ### Include NFSv3 server. ~0.6MB
    
94. #CONFIG_FIRMWARE_INCLUDE_NFSD=y
    
95. 
    
96. ### Include NFSv3 client. ~0.5MB
    
97. #CONFIG_FIRMWARE_INCLUDE_NFSC=y
    
98. 
    
99. ### Include CIFS (SMB) client. ~0.2MB
    
100. #CONFIG_FIRMWARE_INCLUDE_CIFS=y
     
101. 
     
102. ############################################################
     
103. ### Userspace configuration
     
104. ############################################################
     
105. 
     
106. ### Include WebUI international resources. Increased firmware size
     
107. #CONFIG_FIRMWARE_INCLUDE_LANG_BR=y
     
108. #CONFIG_FIRMWARE_INCLUDE_LANG_CZ=y
     
109. #CONFIG_FIRMWARE_INCLUDE_LANG_DA=y
     
110. #CONFIG_FIRMWARE_INCLUDE_LANG_DE=y
     
111. #CONFIG_FIRMWARE_INCLUDE_LANG_ES=y
     
112. #CONFIG_FIRMWARE_INCLUDE_LANG_FI=y
     
113. #CONFIG_FIRMWARE_INCLUDE_LANG_FR=y
     
114. #CONFIG_FIRMWARE_INCLUDE_LANG_NO=y
     
115. #CONFIG_FIRMWARE_INCLUDE_LANG_PL=y
     
116. CONFIG_FIRMWARE_INCLUDE_LANG_RU=y
     
117. #CONFIG_FIRMWARE_INCLUDE_LANG_SV=y
     
118. #CONFIG_FIRMWARE_INCLUDE_LANG_UK=y
     
119. 
     
120. ### Include NTFS-3G FUSE driver (instead of Paragon "ufsd"). ~0.4MB
     
121. #CONFIG_FIRMWARE_INCLUDE_NTFS_3G=y
     
122. 
     
123. ### Include LPR printer daemon. ~0.12MB
     
124. #CONFIG_FIRMWARE_INCLUDE_LPRD=y
     
125. 
     
126. ### Include USB-over-Ethernet printer daemon. ~0.05MB
     
127. #CONFIG_FIRMWARE_INCLUDE_U2EC=y
     
128. 
     
129. ### Include "tcpdump" utility. ~0.6MB
     
130. #CONFIG_FIRMWARE_INCLUDE_TCPDUMP=y
     
131. 
     
132. ### Include "hdparm" utility (allow set HDD spindown timeout and APM). ~0.1MB
     
133. CONFIG_FIRMWARE_INCLUDE_HDPARM=y
     
134. 
     
135. ### Include "parted" utility (allow make GPT partitions). ~0.3MB
     
136. #CONFIG_FIRMWARE_INCLUDE_PARTED=y
     
137. 
     
138. ### Include SMB (and WINS) server. ~1.5MB
     
139. CONFIG_FIRMWARE_INCLUDE_SMBD=y
     
140. 
     
141. ### Include WINS server only. ~0.4MB
     
142. CONFIG_FIRMWARE_INCLUDE_WINS=y
     
143. 
     
144. ### Include syslog for SMB and WINS server. ~0.3MB
     
145. CONFIG_FIRMWARE_INCLUDE_SMBD_SYSLOG=y
     
146. 
     
147. ### Include FTP server. ~0.2MB
     
148. CONFIG_FIRMWARE_INCLUDE_FTPD=y
     
149. 
     
150. ### Include EAP-TTLS and EAP-PEAP authentication support. openssl ~1.2MB, wpa_supplicant +0.04MB
     
151. CONFIG_FIRMWARE_INCLUDE_EAP_PEAP=y
     
152. 
     
153. ### Include HTTPS support for DDNS client. openssl ~1.2MB
     
154. CONFIG_FIRMWARE_INCLUDE_DDNS_SSL=y
     
155. 
     
156. ### Include HTTPS support. openssl ~1.2MB
     
157. CONFIG_FIRMWARE_INCLUDE_HTTPS=y
     
158. 
     
159. ### Include sftp-server. openssl ~1.2MB, sftp-server ~0.06MB
     
160. CONFIG_FIRMWARE_INCLUDE_SFTP=y
     
161. 
     
162. ### Include dropbear SSH. ~0.3MB
     
163. CONFIG_FIRMWARE_INCLUDE_DROPBEAR=y
     
164. 
     
165. ### Make the dropbear symmetrical ciphers and hashes faster. ~0.06MB
     
166. CONFIG_FIRMWARE_INCLUDE_DROPBEAR_FAST_CODE=y
     
167. 
     
168. ### Include OpenSSH instead of dropbear. openssl ~1.2MB, openssh ~1.0MB
     
169. #CONFIG_FIRMWARE_INCLUDE_OPENSSH=y
     
170. 
     
171. ### Include Openvirtual**. IPv6 required. openssl ~1.2MB, openvirtual** ~0.4MB
     
172. CONFIG_FIRMWARE_INCLUDE_OPENvirtual**=y
     
173. 
     
174. ### Include Elliptic Curves (EC) to openssl library. ~0.1MB
     
175. #CONFIG_FIRMWARE_INCLUDE_OPENSSL_EC=y
     
176. 
     
177. ### Include "openssl" executable for generate certificates. ~0.4MB
     
178. CONFIG_FIRMWARE_INCLUDE_OPENSSL_EXE=y
     
179. 
     
180. ### Include xUPNPd IPTV mediaserver. ~0.3MB
     
181. CONFIG_FIRMWARE_INCLUDE_XUPNPD=y
     
182. 
     
183. ### Include Minidlna UPnP mediaserver. ~1.6MB
     
184. CONFIG_FIRMWARE_INCLUDE_MINIDLNA=y
     
185. 
     
186. ### Include Firefly iTunes mediaserver. ~1.0MB
     
187. #CONFIG_FIRMWARE_INCLUDE_FIREFLY=y
     
188. 
     
189. ### Include ffmpeg 0.11.x instead of 0.6.x for Minidlna and Firefly. ~0.1MB
     
190. #CONFIG_FIRMWARE_INCLUDE_FFMPEG_NEW=y
     
191. 
     
192. ### Include Transmission torrent. openssl ~1.2MB, transmission ~1.5MB
     
193. #CONFIG_FIRMWARE_INCLUDE_TRANSMISSION=y
     
194. 
     
195. ### Include Transmission-Web-Control (advanced WebUI). ~0.8MB
     
196. #CONFIG_FIRMWARE_INCLUDE_TRANSMISSION_WEB_CONTROL=y
     
197. 
     
198. ### Include Aria2 download manager. openssl ~1.2MB, aria2 ~3.5MB
     
199. #CONFIG_FIRMWARE_INCLUDE_ARIA=y
     

复制代码

In file included from include/linux/irq.h:27,
                 from include/asm-generic/hardirq.h:12,
                 from include/asm/hardirq.h:16,
                 from include/linux/hardirq.h:7,
                 from include/linux/interrupt.h:12,
                 from arch/mips/kernel/asm-offsets.c:15:
include/asm/irq.h:18:17: error: irq.h: No such file or directory
In file included from include/linux/irq.h:364,
                 from include/asm-generic/hardirq.h:12,
                 from include/asm/hardirq.h:16,
                 from include/linux/hardirq.h:7,
                 from include/linux/interrupt.h:12,
                 from arch/mips/kernel/asm-offsets.c:15:
include/linux/irqdesc.h: At top level:
include/linux/irqdesc.h:79: error: 'NR_IRQS' undeclared here (not in a function)
make[2]: *** [arch/mips/kernel/asm-offsets.s] Error 1
make[1]: *** [prepare0] Error 2
make[1]: *** Waiting for unfinished jobs....
  HOSTLD  scripts/mod/modpost
make[1]: Leaving directory `/home/ano/rlab/ftmp/trunk/linux-3.4.x'
make: *** [linux] Error 1

an***

有把config下的board的Y1S重命名成NHNS

hiboyhi***

anoid 发表于 2015-12-1 15:35
换了32位Ubuntu还是会报错，用汉化文件覆盖了源码，是这里的问题吗？还是config配置出问题了？
In file in ...

不能直接覆盖，只做参考
毕竟经过这么多版本更新

hiboyhi***

anoid 发表于 2015-12-1 15:35
换了32位Ubuntu还是会报错，用汉化文件覆盖了源码，是这里的问题吗？还是config配置出问题了？
In file in ...

不能直接覆盖，只做参考
毕竟经过这么多版本更新

Love4***

hiboyhiboyhiboy 发表于 2015-12-1 09:43
今晚编译一个

thanks 麻烦了

ded***

Dec  1 17:40:30 pdnsd: restart
Dec  1 17:40:30 dnsmasq[6225]: using nameserver 216.6.200.139#53
Dec  1 17:40:30 dnsmasq[6225]: using nameserver 61.139.2.69#53
Dec  1 17:40:30 admin: Failed to start pdnsd from .
Dec  1 17:41:37 pdnsd: restart
Dec  1 17:41:38 admin: Failed to start pdnsd from .
Dec  1 17:41:38 SS: 找不到pdnsd进程92，重启pdnsd
Dec  1 17:41:58 dnsmasq[6225]: exiting on receipt of SIGTERM
Dec  1 17:41:58 dnsmasq[6848]: started, version 2.75 cachesize 1024
Dec  1 17:41:58 dnsmasq[6848]: compile time options: IPv6 GNU-getopt no-RTC no-DBus no-i18n no-IDN DHCP DHCPv6 no-scripts TFTP no-conntrack ipset no-auth no-DNSSEC no-loop-detect no-inotify
Dec  1 17:41:58 dnsmasq-dhcp[6848]: DHCP, IP range 192.168.2.2 -- 192.168.2.244, lease time 1d
Dec  1 17:41:58 dnsmasq-dhcp[6848]: DHCP, sockets bound exclusively to interface br0
Dec  1 17:41:58 dnsmasq[6848]: read /etc/hosts - 3 addresses
Dec  1 17:41:58 dnsmasq[6848]: read /etc/storage/dnsmasq/hosts - 1 addresses
Dec  1 17:41:58 dnsmasq-dhcp[6848]: read /etc/dnsmasq/dhcp/dhcp-hosts.rc
Dec  1 17:41:58 dnsmasq[6848]: using nameserver 216.6.200.139#53
Dec  1 17:41:58 dnsmasq[6848]: using nameserver 61.139.2.69#53

SS一直无法连接，不知道哪里没设置好。另外，11.15版还能下载吗

iSk***

迅雷快鸟支持定时重启了？

woai***

Dec  1 17:55:38 pdnsd: restart
Dec  1 17:55:38 dnsmasq[1601]: using nameserver 210.21.196.6#53
Dec  1 17:55:38 dnsmasq[1601]: using nameserver 221.5.88.88#53
Dec  1 17:55:38 admin: Failed to start pdnsd from .

老大，为什么我pdnsd一直启动失败，ss也连不上。。哪里还要设置吗？

ulw***

支持，支持，再支持！