|
|
本帖最后由 lang007008 于 2019-6-22 23:04 编辑
随便找了2个 S805播放器的固件刷,可惜不匹配 能启动 能接鼠标控制 有线网卡不能用.遥控器没去弄(班的正面中间那3个点是接红外线遥控接收头的,我只想刷LINUX系统弄服务器玩)
播放器固件的 bootloader UBOOT 应该不匹配 网卡不正常
有谁有 玩客云匹配的bootloader UBOOT吗?
QA5:B;SVN:B72 OC:1FF;STS:0;BOOT:0;INIT:0;READ:0;CHECK:0ASS:0;
no sdio debug board detected
TE : 221322
BT : 11:41:09 Dec 3 2015
PMU:NONE
##### VDDEE voltage = 0x044c
CPU clock is 792MHz
DDR mode: 32 bit mode (auto)
DDR size: 1GB (auto)
DDR check: Pass!
DDR clock: 636MHz with 2T mode
DDR pll bypass: Disabled
DDR init use : 15461 us
HHH
Boot From SDIO C
SD_boot_type: 00000002
card_type: 00000003
0x0000009f
ucl decompress...pass
0x12345678
Boot from internal device 1st eMMC on SDIO C
TE : 444225
System Started
U-boot-00000-gfcb95b0-dirty(m8b_m201_v1@fcb95b0d) (Dec 03 2015 - 11:40:38)
clr h-ram
DRAM: 1 GiB
relocation Offset is: 2fec8000
show partition table:
part: 0, name : logo, size : 2000000
part: 1, name : recovery, size : 2000000
part: 2, name : misc, size : 2000000
part: 3, name : boot, size : 2000000
part: 4, name : system, size : 40000000
part: 5, name : private, size : 2000000
part: 6, name : cache, size : 20000000
part: 7, name : data, size : end
aml_card_type=0x100
MMC: [mmc_register] add mmc dev_num=0, port=1, if_type=6
[mmc_register] add mmc dev_num=1, port=2, if_type=6
SDIO Port B: 0, SDIO Port C: 1
The osc_clk is not running now!
power init
out reg=c110804c,value=dfffffff
IR init done!
register usb cfg[0][1] = 3ff73b38
register usb cfg[2][0] = 3ff766d8
The osc_clk is not running now!
init 32k clock
out reg=c8100024,value=bffb3fff
out reg=c8100024,value=bffb3ffb
NAND: EMMC BOOT: not init nand
do not init nand : cause boot_device_flag without nand
get_boot_device_flag: init_ret -1
get_boot_device_flag EMMC BOOT:
Emmckey: Access range is illegal!
[mmc_init] SDIO Port C:1, if_type=6, initialized OK!
[mmc_get_partition_table] skip cache partition.
Partition table get from SPL is :
name offset size flag
===================================================================================
0: bootloader 0 400000 0
1: reserved 2400000 4000000 0
2: cache 6c00000 20000000 2
3: env 27400000 800000 0
4: logo 28400000 2000000 1
5: recovery 2ac00000 2000000 1
6: misc 2d400000 2000000 1
7: boot 2fc00000 2000000 1
8: system 32400000 40000000 1
9: private 72c00000 2000000 1
10: data 75400000 15cc00000 4
mmc read lba=0x12000, blocks=0x1
mmc read lba=0x12001, blocks=0x1
mmc_read_partition_tbl: mmc read partition OK!
eMMC/TSD partition table have been checked OK!
i=0,register --- emmc_key
MMC BOOT, emmc_env_relocate_spec : env_relocate_spec 59
set_storage_device_flag: store 2
hdmimode env value is 720p
mem size is 1024
The osc_clk is running now!
checked platform is costdown,use costdown dtd
aml_dt: m8b_m201C_1G
aml_dt is: m8b_m201C_1G
Multi dtb tool version: v2 .
Multi dtb detected, support 4 dtbs.
aml_dt soc: m8b platform: m201C variant: 1G
dtb 0 soc: m8b plat: m201 vari: 1G
dtb 1 soc: m8b plat: m201 vari: 512M
dtb 2 soc: m8b plat: m201C vari: 1G
dtb 3 soc: m8b plat: m201C vari: 512M
Find match dtb: 2
vpu clk_level in dts: 3
set vpu clk: 182150000Hz, readback: 182150000Hz(0x701)
Net: Meson_Ethernet
init suspend firmware done. (ret:0)
cvbs trimming.1.v5: 0xa0, 0x0
hdmi tx power init
vdac open.1 = 0x1, 0x0
mode is: 4
viu chan = 1
config HPLL
config HPLL done
-->reboot_mode:0x0
-->powerkey:0x0
reboot_mode=charging
Hit Enter key to stop autoboot -- : 1 tstc enter
exit abortboot: 1
m8b_m201C_512M#<INTERRUPT>
m8b_m201C_512M#help
? - alias for 'help'
adc - M6 ADC test
amlnf - AMLPHYNAND sub-system
amlnf_test- AMLPHYNAND sub-system
autoping- do auto ping test
autoscr - run script from memory
base - print or set address offset
bdinfo - print Board Info structure
bmp - manipulate BMP image data
board_dt_id_process- Get the board ddr size
boardid_prefetch- boardid sub-system
bootm - boot application image from memory
bootp - boot image via network using BOOTP/TFTP protocol
cali - configure clock phare
calinfo - calinfo print the chip calibration info
cbusreg - cbus register read/write
clear_rebootmode- clear rebootmode
clkmsr - measure PLL clock
cmp - memory compare
coninfo - print console devices and information
cp - memory copy
crc32 - checksum calculation
dcache - enable or disable data cache
defenv - default environment
defenv_reserve_env- reserve env
defenv_without- defenv without environment variables
dhcp - boot image via network using DHCP/TFTP protocol
dtbinit - init some env by reading dtb file
dtbload - load binary dtb file from a dos filesystem
echo - echo args to console
editenv - edit environment variable
efuse - efuse version/licence/mac/hdcp/usid read/write or dump raw efuse data commands or info(display chip efuse info)
env - environment handling commands
ethchk - check ethernet status
ethdbg - set ethernet debug level
ethmode - set ethernet mac mode
ethrst - reset ethernet phy
exit - exit script
ext2load- load binary file from a Ext2 filesystem
ext2ls - list files in a directory (default /)
false - do nothing, unsuccessfully
fatexist- find the file from a dos filesystem
fatinfo - print information about filesystem
fatload - load binary file from a dos filesystem
fatls - list files in a directory (default /)
fdt - flattened device tree utility commands
get_img_size- get img size and save the result as a environment variable
get_rebootmode- get reboot mode
go - start application at address 'addr'
gset - gpio commands
help - print command description/usage
icache - enable or disable instruction cache
imgread - Read the image from internal flash with actual size
imxtract- extract a part of a multi-image
irdetect- Detect IR Key to start recovery system
irkey - irkey key_value time_value
itest - return true/false on integer compare
keyunify- key unify sub-system
kgdb - enter gdb remote debug mode
loadb - load binary file over serial line (kermit mode)
loadenv - load environment at address 'addr'
loads - load S-Record file over serial line
loadx - load binary file over serial line (xmodem mode)
loady - load binary file over serial line (ymodem mode)
logo - logo sub-system
loop - infinite loop on address range
macreg - ethernet mac register read/write/dump
md - memory display
mdc_clk - do mdc clock
mm - memory modify (auto-incrementing address)
mmc - MMC sub system
mmcinfo - mmcinfo <dev num>-- display MMC info
msleep - delay execution for some time
msr - Meson msr sub-system
mtest - simple RAM read/write test
mw - memory write (fill)
netspd_f- enforce eth speed
nm - memory modify (constant address)
phyreg - ethernet phy register read/write/dump
ping - send ICMP ECHO_REQUEST to network host
printenv- print environment variables
put - put storage
pwm - pwm sub-system
rarpboot- boot image via network using RARP/TFTP protocol
reset - Perform RESET of the CPU
run - run commands in an environment variable
saradc - saradc sub-system
saveenv - save environment variables to persistent storage
sdc_burn- Burning with amlogic format package in sdmmc
sdc_update- Burning a partition with image file in sdmmc card
secukey - security KEY sub-system
setenv - set environment variables
sf - SPI flash sub-system
showvar - print local hushshell variables
sleep - delay execution for some time
source - run script from memory
ssecukey- NAND KEY sub-system
store - STORE sub-system
suspend - suspend
test - minimal test like /bin/sh
tftpboot- boot image via network using TFTP protocol
true - do nothing, successfully
unifykey- unifykey read/write based on the driver keymanage
unpackimg- unpack imgpack to single
update - Enter v2 usbburning mode
usb - USB sub-system
usbbc - test usb bc
usbboot - boot from USB device
usid_prefetch- usid sub-system
uuid_prefetch- uuid sub-system
version - print monitor, compiler and linker version
video - video sub-system
m8b_m201C_512M# |
|
/1 
简体中文
繁體中文
English
日本語
Deutsch
한국 사람
بالعربية
TÜRKÇE
português
คนไทย
IP卡
狗仔卡
置顶卡
沉默卡
喧嚣卡
顶贴卡
显身卡
