|
本帖最后由 kyd12345 于 2013-7-22 21:33 编辑
TTL接法:左上GND,左下TX,右下RX
参考:1.http://foro.seguridadwireless.net/openwrt/openwrt-en-comtrend-5813n/
2.https://github.com/Noltari/openwrt
固件下载
http://pan.baidu.com/share/link?shareid=2901735555&uk=3791774029
官方固件
http://support.netcommwireless.com/product/3g/3g21wb133C版CFE
LED灯含义:
1.信号强度 HIGH
2.信号强度 MID
3.信号强度 LOW
4.2G
5.3G
6.LAN4
7.LAN3
8.LAN2
9.LAN1
10.INTERNET
11.WIFI
12.POWER
感谢@759851846提醒:注意刷固件之前要把Board Id改成96368MVWG
默认未开启无线,需手动编辑/etc/config/wireless文件,去掉option disable 1.然后执行wifi up即可开启无线,默认ssid为openwrt,无密码。
界面:
TTL信息见下方- CFE version 1.0.37-102.6-13 for BCM96368 (32bit,SP,BE)
- Build Date: Fri Dec 4 15:43:06 CST 2009 (wenxing@rd5-linux)
- Copyright (C) 2000-2008 Broadcom Corporation.
-
- Parallel flash device: name AM29DL800B, id 0x22cb, size 8192KB
- BCM53115 Fail !!!!
- CPU type 0x2A031: 400MHz, Bus: 160MHz, Ref: 64MHz
- CPU running TP0
- Total memory: 33554432 bytes (32MB)
- Boot Address 0xb8000000
-
-
- Board IP address : 192.168.1.1:ffffff00
- Host IP address : 192.168.1.100
- Gateway IP address :
- Run from flash/host (f/h) : f
- Default host run file name : vmlinux
- Default host flash file name : bcm963xx_fs_kernel
- Boot delay (0-9 seconds) : 1
- Board Id (0-13) : 96368MVWG
- Number of MAC Addresses (1-32) : 11
- Base MAC Address : 00:11:22:33:44:55
- PSI Size (1-64) KBytes : 24
- Main Thread Number [0|1] : 0
- Serial Number : xxxxxxxxxxxxxxx
-
- *** Press any key to stop auto run (1 seconds) ***
- Auto run second count down: 0
- Booting from only image (0xb8010000) ...
- Code Address: 0x80010000, Entry Address: 0x80010000
- LZMA: Prossible old LZMA format, trying to decompress..
- Decompression OK!
- Entry at 0x80010000
- Closing network.
- Disabling Switch ports.
- Flushing Receive Buffers...
- 0 buffers found.
- Closing DMA Channels.
- Starting program at 0x80010000
- [ 0.000000] Linux version 3.8.11 (Quella@Openwrt) (gcc version 4.6.4 (OpenWrt/Li
- naro GCC 4.6-2012.12 r36529) ) #1 Mon Jul 17 20:15:1 CST 2013
- [ 0.000000] Detected Broadcom 0x6368 CPU revision b1
- [ 0.000000] CPU frequency is 400 MHz
- [ 0.000000] 32MB of RAM installed
- [ 0.000000] registering 38 GPIOs
- [ 0.000000] board_bcm963xx: Boot address 0xb8000000
- [ 0.000000] board_bcm963xx: CFE version: 1.0.37-102.6
- [ 0.000000] bootconsole [early0] enabled
- [ 0.000000] CPU revision is: 0002a031 (Broadcom BMIPS4350)
- [ 0.000000] board_bcm963xx: board name: 96368MVWG
- [ 0.000000] Determined physical RAM map:
- [ 0.000000] memory: 02000000 @ 00000000 (usable)
- [ 0.000000] Initrd not found or empty - disabling initrd
- [ 0.000000] Zone ranges:
- [ 0.000000] Normal [mem 0x00000000-0x01ffffff]
- [ 0.000000] Movable zone start for each node
- [ 0.000000] Early memory node ranges
- [ 0.000000] node 0: [mem 0x00000000-0x01ffffff]
- [ 0.000000] Reserving 0MB of memory at 0MB for crashkernel
- [ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 16 bytes.
- [ 0.000000] Primary data cache 32kB, 2-way, VIPT, cache aliases, linesize 16
- bytes
- [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pag
- es: 8128
- [ 0.000000] Kernel command line: root=/dev/mtdblock2 rootfstype=squashfs,jff
- s2 noinitrd console=ttyS0,115200
- [ 0.000000] PID hash table entries: 128 (order: -3, 512 bytes)
- [ 0.000000] Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)
- [ 0.000000] Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)
- [ 0.000000] __ex_table already sorted, skipping sort
- [ 0.000000] Memory: 28912k/32768k available (2336k kernel code, 3856k reserve
- d, 607k data, 252k init, 0k highmem)
- [ 0.000000] NR_IRQS:128
- [ 0.000000] Calibrating delay loop... 397.82 BogoMIPS (lpj=795648)
- [ 0.032000] pid_max: default: 32768 minimum: 301
- [ 0.036000] Mount-cache hash table entries: 512
- [ 0.040000] NET: Registered protocol family 16
- [ 0.048000] registering PCI controller with io_map_base unset
- [ 0.060000] bio: create slab <bio-0> at 0
- [ 0.064000] PCI host bridge to bus 0000:00
- [ 0.068000] pci_bus 0000:00: root bus resource [mem 0x30000000-0x37ffffff]
- [ 0.072000] pci_bus 0000:00: root bus resource [io 0x8000000-0x800ffff]
- [ 0.076000] pci_bus 0000:00: No busn resource found for root bus, will use [b
- us 00-ff]
- [ 0.092000] pci 0000:00:01.0: BAR 0: assigned [mem 0x30000000-0x30003fff]
- [ 0.096000] Switching to clocksource MIPS
- [ 0.104000] PCI: Enabling device 0000:00:01.0 (0000 -> 0002)
- [ 0.132000] ssb: Found chip with id 0x4322, rev 0x01 and package 0x09
- [ 0.200000] ssb: Sonics Silicon Backplane found on PCI device 0000:00:01.0
- [ 0.208000] NET: Registered protocol family 2
- [ 0.216000] TCP established hash table entries: 512 (order: 0, 4096 bytes)
- [ 0.224000] TCP bind hash table entries: 512 (order: -1, 2048 bytes)
- [ 0.228000] TCP: Hash tables configured (established 512 bind 512)
- [ 0.236000] TCP: reno registered
- [ 0.240000] UDP hash table entries: 256 (order: 0, 4096 bytes)
- [ 0.244000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
- [ 0.252000] NET: Registered protocol family 1
- [ 0.260000] audit: initializing netlink socket (disabled)
- [ 0.264000] type=2000 audit(0.264:1): initialized
- [ 0.272000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
- [ 0.276000] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORIT
- Y) (c) 2001-2006 Red Hat, Inc.
- [ 0.288000] msgmni has been set to 56
- [ 0.292000] io scheduler noop registered
- [ 0.296000] io scheduler deadline registered (default)
- [ 0.304000] bcm63xx_uart.0: ttyS0 at MMIO 0xb0000100 (irq = 10) is a bcm63xx_
- uart
- [ 0.312000] console [ttyS0] enabled, bootconsole disabled
- [ 0.312000] console [ttyS0] enabled, bootconsole disabled
- [ 0.324000] bcm63xx-rng bcm63xx-rng: registered RNG driver
- [ 0.332000] physmap platform flash device: 08000000 at 18000000
- [ 0.336000] physmap-flash.0: Found 1 x16 devices at 0x0 in 16-bit bank. Manuf
- acturer ID 0x0000c2 Chip ID 0x0022cb
- [ 0.348000] Amd/Fujitsu Extended Query Table at 0x0040
- [ 0.352000] Amd/Fujitsu Extended Query version 1.1.
- [ 0.360000] number of CFI chips: 1
- [ 0.364000] bcm63xxpart: CFE boot tag found with version 6 and board type 963
- 69R-1231N
- [ 0.372000] bcm63xxpart: Partition 0 is CFE offset 0 and length 10000
- [ 0.376000] bcm63xxpart: Partition 1 is kernel offset 10100 and length 10ff00
- [ 0.384000] bcm63xxpart: Partition 2 is rootfs offset 120000 and length 6d000
- 0
- [ 0.392000] bcm63xxpart: Partition 3 is nvram offset 7f0000 and length 10000
- [ 0.400000] bcm63xxpart: Partition 4 is linux offset 10000 and length 7e0000
- [ 0.408000] bcm63xxpart: Spare partition is offset 370004 and length 47fffc
- [ 0.412000] 5 bcm63xxpart partitions found on MTD device physmap-flash.0
- [ 0.420000] Creating 5 MTD partitions on "physmap-flash.0":
- [ 0.428000] 0x000000000000-0x000000010000 : "CFE"
- [ 0.432000] 0x000000010100-0x000000120000 : "kernel"
- [ 0.440000] mtd: partition "kernel" must either start or end on erase block b
- oundary or be smaller than an erase block -- forcing read-only
- [ 0.452000] 0x000000120000-0x0000007f0000 : "rootfs"
- [ 0.460000] mtd: partition "rootfs" set to be root filesystem
- [ 0.468000] mtd: partition "rootfs_data" created automatically, ofs=370000, l
- en=480000
- [ 0.476000] 0x000000370000-0x0000007f0000 : "rootfs_data"
- [ 0.484000] 0x0000007f0000-0x000000800000 : "nvram"
- [ 0.488000] 0x000000010000-0x0000007f0000 : "linux"
- [ 0.496000] bcm63xx-spi bcm63xx-spi: at 0xb0000800 (irq 9, FIFOs size 542)
- [ 0.544000] b53_common: found switch: BCM63xx, rev 0
- [ 0.548000] bcm63xx-wdt bcm63xx-wdt: started, timer margin: 30 sec
- [ 0.560000] TCP: cubic registered
- [ 0.564000] NET: Registered protocol family 17
- [ 0.568000] 8021q: 802.1Q VLAN Support v1.8
- [ 0.580000] VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
- [ 0.592000] Freeing unused kernel memory: 252k freed
- - preinit -
- Press the [f] key and hit [enter] to enter failsafe mode
- - regular preinit -
- [ 6.484000] jffs2: notice: (321) jffs2_build_xattr_subsystem: complete buildi
- ng xattr subsystem, 1 of xdatum (0 unchecked, 0 orphan) and 10 of xref (0 dead,
- 2 orphan) found.
- switching to jffs2
- - init -
-
- Please press Enter to activate this console. [ 8.920000] compat-drivers backp
- ort release: compat-drivers-2013-03-28-5
- [ 8.924000] Backport based on wireless-testing.git master-2013-04-16
- [ 8.932000] compat.git: wireless-testing.git
- [ 8.984000] cfg80211: Calling CRDA to update world regulatory domain
- [ 8.988000] cfg80211: World regulatory domain updated:
- [ 8.992000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gai
- n, max_eirp)
- [ 9.004000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 20
- 00 mBm)
- [ 9.012000] cfg80211: (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 20
- 00 mBm)
- [ 9.020000] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 20
- 00 mBm)
- [ 9.028000] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 20
- 00 mBm)
- [ 9.036000] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 20
- 00 mBm)
- [ 9.372000] NET: Registered protocol family 10
- [ 9.732000] SCSI subsystem initialized
- [ 9.984000] usbcore: registered new interface driver usbfs
- [ 9.988000] usbcore: registered new interface driver hub
- [ 9.996000] usbcore: registered new device driver usb
- [ 10.716000] b43-phy0: Broadcom 4322 WLAN found (core revision 16)
- [ 10.768000] b43-phy0: Found PHY: Analog 8, Type 4 (N), Revision 4
- [ 10.796000] Broadcom 43xx driver loaded [ Features: PNL ]
- [ 11.172000] Button Hotplug driver version 0.4.1
- [ 12.076000] PPP generic driver version 2.4.2
- [ 12.160000] ip_tables: (C) 2000-2006 Netfilter Core Team
- [ 12.448000] NET: Registered protocol family 24
- [ 12.616000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
- [ 12.640000] ehci-platform: EHCI generic platform driver
- [ 12.748000] ehci-platform ehci-platform: EHCI Host Controller
- [ 12.752000] ehci-platform ehci-platform: new USB bus registered, assigned bus
- number 1
- [ 12.760000] ehci-platform ehci-platform: irq 15, io mem 0xb0001500
- [ 12.780000] ehci-platform ehci-platform: USB 2.0 started, EHCI 1.00, overcurr
- ent ignored
- [ 12.788000] hub 1-0:1.0: USB hub found
- [ 12.792000] hub 1-0:1.0: 2 ports detected
- [ 12.828000] nf_conntrack version 0.5.0 (455 buckets, 1820 max)
- [ 13.388000] usb 1-1: new high-speed USB device number 2 using ehci-platform
- [ 13.608000] hub 1-1:1.0: USB hub found
- [ 13.624000] hub 1-1:1.0: 4 ports detected
- [ 13.664000] ip6_tables: (C) 2000-2006 Netfilter Core Team
- [ 13.896000] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
- [ 13.904000] ohci-platform ohci-platform: Generic Platform OHCI Controller
- [ 13.908000] ohci-platform ohci-platform: new USB bus registered, assigned bus
- number 2
- [ 13.916000] ohci-platform ohci-platform: irq 13, io mem 0xb0001600
- [ 13.984000] hub 2-0:1.0: USB hub found
- [ 13.988000] hub 2-0:1.0: 1 port detected
- [ 14.084000] Initializing USB Mass Storage driver...
- [ 14.092000] usbcore: registered new interface driver usb-storage
- [ 14.096000] USB Mass Storage support registered.
- [ 14.124000] usbcore: registered new interface driver ums-alauda
- [ 14.148000] usbcore: registered new interface driver ums-cypress
- [ 14.172000] usbcore: registered new interface driver ums-datafab
- [ 14.200000] usbcore: registered new interface driver ums-freecom
- [ 14.224000] usbcore: registered new interface driver ums-isd200
- [ 14.252000] usbcore: registered new interface driver ums-jumpshot
- [ 14.276000] usbcore: registered new interface driver ums-karma
- [ 14.304000] usbcore: registered new interface driver ums-sddr09
- [ 14.332000] usbcore: registered new interface driver ums-sddr55
- [ 14.356000] usbcore: registered new interface driver ums-usbat
- [ 19.364000] device eth0.1 entered promiscuous mode
- [ 19.368000] device eth0 entered promiscuous mode
- [ 19.380000] br-lan: port 1(eth0.1) entered forwarding state
- [ 19.384000] br-lan: port 1(eth0.1) entered forwarding state
- [ 20.356000] IPv6: ADDRCONF(NETDEV_CHANGE): eth0.1: link becomes ready
- [ 21.388000] br-lan: port 1(eth0.1) entered forwarding state
- [ 25.096000] b43-phy0: Loading firmware version 666.2 (2011-02-23 01:15:07)
- [ 25.196000] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
- [ 25.248000] device wlan0 entered promiscuous mode
- [ 25.456000] b43-phy0: Loading firmware version 666.2 (2011-02-23 01:15:07)
- [ 25.548000] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
- [ 25.576000] br-lan: port 2(wlan0) entered forwarding state
- [ 25.580000] br-lan: port 2(wlan0) entered forwarding state
- [ 25.588000] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
- [ 27.584000] br-lan: port 2(wlan0) entered forwarding state
-
-
-
- BusyBox v1.19.4 (2013-07-17 20:15:40 CST) built-in shell (ash)
- Enter 'help' for a list of built-in commands.
-
- _______ ________ __
- | |.-----.-----.-----.| | | |.----.| |_
- | - || _ | -__| || | | || _|| _|
- |_______|| __|_____|__|__||________||__| |____|
- |__| W I R E L E S S F R E E D O M
- -----------------------------------------------------
- BARRIER BREAKER (Bleeding Edge, r36529)
- -----------------------------------------------------
- * 1/2 oz Galliano Pour all ingredients into
- * 4 oz cold Coffee an irish coffee mug filled
- * 1 1/2 oz Dark Rum with crushed ice. Stir.
- * 2 tsp. Creme de Cacao
- -----------------------------------------------------
- root@OpenWrt:/# df -h
- Filesystem Size Used Available Use% Mounted on
- rootfs 4.5M 276.0K 4.2M 6% /
- /dev/root 2.5M 2.5M 0 100% /rom
- tmpfs 14.2M 64.0K 14.2M 0% /tmp
- tmpfs 512.0K 0 512.0K 0% /dev
- /dev/mtdblock3 4.5M 276.0K 4.2M 6% /overlay
- overlayfs:/overlay 4.5M 276.0K 4.2M 6% /
- root@OpenWrt:/# free
- total used free shared buffers
- Mem: 29164 19832 9332 0 2228
- -/+ buffers: 17604 11560
- Swap: 0 0 0
- root@OpenWrt:/# cat /proc/cpuinfo
- system type : bcm63xx/96368MVWG (0x6368/0xB1)
- processor : 0
- cpu model : Broadcom BMIPS4350 V3.1
- BogoMIPS : 397.82
- wait instruction : yes
- microsecond timers : yes
- tlb_entries : 32
- extra interrupt vector : yes
- hardware watchpoint : no
- ASEs implemented :
- shadow register sets : 1
- kscratch registers : 0
- core : 0
- VCED exceptions : not available
- VCEI exceptions : not available
-
- root@OpenWrt:/#
复制代码 |
本帖子中包含更多资源
您需要 登录 才可以下载或查看,没有账号?立即注册
×
|