|
楼主 |
发表于 2014-7-16 18:16
|
显示全部楼层
U-Boot 1.1.3 (Nov 3 2011 - 09:59:01)
Board: Ralink APSoC DRAM: 32 MB
relocate_code Pointer at: 81fb0000
config usb..
Set info->start[0]=BF000000
flash_protect ON: from 0xBF000000 to 0xBF01E6D7
flash_protect ON: from 0xBF030000 to 0xBF030FFF
*** Warning - bad CRC, using default environment
============================================
Ralink UBoot Version: 3.5.0.0
--------------------------------------------
ASIC 3052_MP2 (Port5<->None)
DRAM component: 128 Mbits SDR
DRAM bus: 32 bit
Total memory: 32 MBytes
Flash component: NOR Flash
Date:Nov 3 2011 Time:09:59:01
============================================
icache: sets:256, ways:4, linesz:32 ,total:32768
dcache: sets:128, ways:4, linesz:32 ,total:16384
##### The CPU freq = 384 MHZ ####
estimate memory size =32 Mbytes
Please choose the operation:
1: Load system code to SDRAM via TFTP.
2: Load system code then write to Flash via TFTP.
3: Boot system code via Flash (default).
4: Entr boot command line interface.
7: Load Boot Loader code then write to Flash via Serial.
9: Load Boot Loader code then write to Flash via TFTP.
You choosed 2
0
2: System Load Linux Kernel then write to Flash via TFTP.
Warning!! Erase Linux in Flash then burn new one. Are you sure?(Y/N)
Please Input new ones /or Ctrl-C to discard
Input device IP (192.168.1.1) ==:192.168.1.1
Input server IP (192.168.1.2) ==:192.168.1.2
Input Linux Kernel filename () ==:111.bin
netboot_common, argc= 3
NetTxPacket = 0x81FE6980
KSEG1ADDR(NetTxPacket) = 0xA1FE6980
NetLoop,call eth_halt !
NetLoop,call eth_init !
Trying Eth0 (10/100-M)
Waitting for RX_DMA_BUSY status Start... done
Header Payload scatter function is Disable !!
ETH_STATE_ACTIVE!!
Using Eth0 (10/100-M) device
TFTP from server 192.168.1.2; our IP address is 192.168.1.1
Filename '111.bin'.
TIMEOUT_COUNT=10,Load address: 0x80100000
Loading: *
ArpTimeoutCheck
T Got ARP REQUEST, return our IP
T Got ARP REPLY, set server/gtwy eth addr (60:eb:69:ad:6a:d5)
Got it
checksum bad
Got ARP REQUEST, return our IP
checksum bad
checksum bad
Got ARP REQUEST, return our IP
Got ARP REQUEST, return our IP
checksum bad
Got ARP REQUEST, return our IP
checksum bad
checksum bad
Got ARP REQUEST, return our IP
T T Got ARP REQUEST, return our IP
Got ARP REQUEST, return our IP
Got ARP REQUEST, return our IP
T T Got ARP REQUEST, return our IP
T T Got ARP REQUEST, return our IP
T T Got ARP REQUEST, return our IP
Retry count exceeded; starting again
Trying Eth0 (10/100-M)
ETH_STATE_ACTIVE!!
Got ARP REQUEST, return our IP
Using Eth0 (10/100-M) device
TFTP from server 192.168.1.2; our IP address is 192.168.1.1
Filename '111.bin'.
TIMEOUT_COUNT=10,Load address: 0x80100000
Loading: Got ARP REPLY, set server/gtwy eth addr (60:eb:69:ad:6a:d5)
Got it
checksum bad
checksum bad
Got ARP REQUEST, return our IP
checksum bad
checksum bad
Got ARP REQUEST, return our IP
checksum bad
checksum bad
Got ARP REQUEST, return our IP
T T Got ARP REQUEST, return our IP |
|