|
楼主 |
发表于 2014-9-27 16:26
|
显示全部楼层
Openwrt 12.09:
Starting kernel ...
OpenWrt kernel loader for AR7XXX/AR9XXX
Copyright (C) 2011 Gabor Juhos <juhosg@openwrt.org>
Looking for OpenWrt image... found at 0xbf022000
Decompressing kernel... done!
Starting kernel at 80060000...
[ 0.000000] Linux version 3.3.8 (blogic@Debian-60-squeeze-64-minimal) (gcc version 4.6.3 20120201 (prerelease) (Linaro GCC 4.6-2012.02) ) #1 Sat Mar 23 16:49:30 UTC 2013
[ 0.000000] bootconsole [early0] enabled
[ 0.000000] CPU revision is: 00019374 (MIPS 24Kc)
[ 0.000000] SoC: Atheros AR9132 rev 1
[ 0.000000] Clocks: CPU:400.000MHz, DDR:400.000MHz, AHB:100.000MHz, Ref:5.000MHz
[ 0.000000] Determined physical RAM map:
[ 0.000000] memory: 02000000 @ 00000000 (usable)
[ 0.000000] Initrd not found or empty - disabling initrd
[ 0.000000] Zone PFN ranges:
[ 0.000000] Normal 0x00000000 -> 0x00002000
[ 0.000000] Movable zone start PFN for each node
[ 0.000000] Early memory PFN ranges
[ 0.000000] 0: 0x00000000 -> 0x00002000
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 8128
[ 0.000000] Kernel command line: board=TL-WR941ND console=ttyS0,115200 rootfstype=squashfs,jffs2 noinitrd
[ 0.000000] PID hash table entries: 128 (order: -3, 512 bytes)
[ 0.000000] Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.000000] Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
[ 0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
[ 0.000000] Writing ErrCtl register=00000000
[ 0.000000] Readback ErrCtl register=00000000
[ 0.000000] Memory: 29000k/32768k available (2211k kernel code, 3768k reserved, 418k data, 212k init, 0k highmem)
[ 0.000000] SLUB: Genslabs=9, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[ 0.000000] NR_IRQS:51
[ 0.000000] Calibrating delay loop... 265.42 BogoMIPS (lpj=1327104)
[ 0.080000] pid_max: default: 32768 minimum: 301
[ 0.080000] Mount-cache hash table entries: 512
[ 0.090000] NET: Registered protocol family 16
[ 0.090000] gpiochip_add: registered GPIOs 0 to 21 on device: ath79
[ 0.100000] MIPS: machine is TP-LINK TL-WR941ND
[ 0.330000] bio: create slab <bio-0> at 0
[ 0.340000] Switching to clocksource MIPS
[ 0.350000] NET: Registered protocol family 2
[ 0.350000] IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.350000] TCP established hash table entries: 1024 (order: 1, 8192 bytes)
[ 0.360000] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.360000] TCP: Hash tables configured (established 1024 bind 1024)
[ 0.370000] TCP reno registered
[ 0.370000] UDP hash table entries: 256 (order: 0, 4096 bytes)
[ 0.380000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[ 0.390000] NET: Registered protocol family 1
[ 0.410000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.410000] JFFS2 version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 0.420000] msgmni has been set to 56
[ 0.430000] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 254)
[ 0.440000] io scheduler noop registered
[ 0.440000] io scheduler deadline registered (default)
[ 0.440000] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled
[ 0.480000] serial8250.0: ttyS0 at MMIO 0x18020000 (irq = 11) is a 16550A
[ 0.480000] console [ttyS0] enabled, bootconsole disabled
[ 0.480000] console [ttyS0] enabled, bootconsole disabled
[ 0.500000] m25p80 spi0.0: found mx25l6405d, expected m25p80
[ 0.500000] m25p80 spi0.0: mx25l6405d (8192 Kbytes)
[ 0.510000] 5 tp-link partitions found on MTD device spi0.0
[ 0.510000] Creating 5 MTD partitions on "spi0.0":
[ 0.520000] 0x000000000000-0x000000020000 : "u-boot"
[ 0.530000] 0x000000020000-0x00000010bc00 : "kernel"
[ 0.530000] mtd: partition "kernel" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
[ 0.550000] 0x00000010bc00-0x0000007f0000 : "rootfs"
[ 0.550000] mtd: partition "rootfs" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
[ 0.560000] mtd: partition "rootfs" set to be root filesystem
[ 0.570000] mtd: partition "rootfs_data" created automatically, ofs=2E0000, len=510000
[ 0.580000] 0x0000002e0000-0x0000007f0000 : "rootfs_data"
[ 0.590000] 0x0000007f0000-0x000000800000 : "art"
[ 0.590000] 0x000000020000-0x0000007f0000 : "firmware"
[ 0.600000] ag71xx_mdio: probed
[ 0.610000] eth0: Atheros AG71xx at 0xb9000000, irq 4
[ 0.920000] TCP cubic registered
[ 0.920000] NET: Registered protocol family 17
[ 0.920000] Bridge firewalling registered
[ 0.930000] Distributed Switch Architecture driver version 0.1
[ 0.930000] eth0[0]: could not detect attached switch
[ 0.940000] eth0[0]: couldn't create dsa switch instance (error -22)
[ 0.940000] 8021q: 802.1Q VLAN Support v1.8
[ 0.960000] VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
[ 0.960000] Freeing unused kernel memory: 212k freed
[ 3.200000] eth0: link up (100Mbps/Full duplex)
- preinit -
Press the [f] key and hit [enter] to enter failsafe mode
- regular preinit -
[ 6.490000] jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00100000: 0x3b38 instead
[ 6.500000] jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00100004: 0x011c instead
[ 6.510000] jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00100008: 0x3b38 instead
[ 6.510000] jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x0010000c: 0x011c instead
[ 6.520000] jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00100010: 0x3a3d instead
[ 6.530000] jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00100014: 0x2004 instead
[ 6.540000] jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00100018: 0x3a3d instead
[ 6.550000] jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x0010001c: 0x2004 instead
[ 6.560000] jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00100020: 0x8a3d instead
[ 6.570000] jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00100024: 0xa91c instead
[ 6.580000] Further such events for this erase block will not be printed
[ 6.710000] JFFS2 notice: (420) jffs2_build_xattr_subsystem: complete building xattr subsystem, 1 of xdatum (0 unchecked, 0 orphan) and 12 of xref (0 dead, 2 orphan) found.
switching to jffs2
- init -
[ 6.910000] eth0: link down
Please press Enter to activate this console. [ 8.730000] Compat-drivers backport release: compat-drivers-2012-09-04-2-gddac993
[ 8.740000] Backport based on wireless-testing.git master-2012-09-07
[ 8.750000] compat.git: wireless-testing.git
[ 8.770000] cfg80211: Calling CRDA to update world regulatory domain
[ 8.780000] cfg80211: World regulatory domain updated:
[ 8.790000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[ 8.790000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 8.800000] cfg80211: (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[ 8.810000] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[ 8.820000] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 8.820000] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 9.190000] usbcore: registered new interface driver usbfs
[ 9.200000] usbcore: registered new interface driver hub
[ 9.200000] usbcore: registered new device driver usb
[ 9.830000] ieee80211 phy0: Atheros AR9100 MAC/BB Rev:7 AR5133 RF Rev:a1 mem=0xb80c0000, irq=2
[ 9.840000] cfg80211: Calling CRDA for country: US
[ 9.840000] cfg80211: Regulatory domain changed to country: US
[ 9.850000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[ 9.860000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2700 mBm)
[ 9.860000] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 1700 mBm)
[ 9.870000] cfg80211: (5250000 KHz - 5330000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 9.880000] cfg80211: (5490000 KHz - 5600000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 9.890000] cfg80211: (5650000 KHz - 5710000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 9.890000] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 3000 mBm)
[ 9.950000] PPP generic driver version 2.4.2
[ 10.190000] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 10.400000] NET: Registered protocol family 24
[ 10.420000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 10.440000] nf_conntrack version 0.5.0 (456 buckets, 1824 max)
[ 10.650000] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 37.360000] Newly-erased block contained word 0x3b38a81c at offset 0x00100000
[ 39.630000] eth0: link up (100Mbps/Full duplex)
[ 45.100000] device wlan0 entered promiscuous mode
[ 45.150000] br-lan: port 1(wlan0) entered forwarding state
[ 45.160000] br-lan: port 1(wlan0) entered forwarding state
[ 47.160000] br-lan: port 1(wlan0) entered forwarding state |
|