求助救砖HG255d

zwjwjz

今天刷HG255d最新UBOOT，死活刷不上。教程是：https://www.right.com.cn/forum/f ... ght=HG255D%2B%CB%A2
刷机过程显示如下：
U-Boot 1.1.3 (May 31 2012 - 20:54:08)

SoC:Ralink APSoC(RT305x)
Memory Testing.......32768K OK.
DRAM:  32 MB
relocate_code Pointer at: 81168000
config usb..

The Flash ID =0000227E

FLASH:S29GL128N, SIZE:16 MBytes SECTOR:128
S29GL128N:Set sect_size = 0x00020000
flash_protect ON: from 0xBF000000 to 0xBF023873
flash_protect ON: from 0xBF040000 to 0xBF040FFF
*** Warning - bad CRC, using default environment

______________________________________________________
|   ____                           ____              |
|  |  _ \ _ __ ___  __ _ _ __ ___ | __ )  _____  __  |
|  | | | | '__/ _ \/ _` | '_ ` _ \|  _ \ / _ \ \/ /  |
|  | |_| | | |  __/ (_| | | | | | | |_) | (_) >  <   |
|  |____/|_|  \___|\__,_|_| |_| |_|____/ \___/_/\_\  |
|                                                    |
|           http://www.openwrt.org.cn                |
|              Board:HuaWei HG255D                   |
|                                                    |
|         lintel<linte@openwrt.org.cn>               |
|____________________________________________________|

ASIC 3052_MP2 (Port5<->Phy)
Flash component: NOR Flash
Build Date:May 31 2012  Time:20:54:08
icache: sets:256, ways:4, linesz:32 ,total:32768
dcache: sets:128, ways:4, linesz:32 ,total:16384

##### The CPU freq = 384 MHZ ####
estimate memory size =32 Mbytes

GPIO Init:
        UARTF_SHARE_MODE:GPIO
        SPI_GPIO_MODE:GPIO

GPIO_MODE_REG status:0x1e

Please choose the operation:
   1: Load system code to SDRAM via TFTP.
   2: Load system code then write to Flash via TFTP.
   3: Boot system code via Flash (default).
   4: Entr boot command line interface.
   7: Load Boot Loader code then write to Flash via Serial.
   9: Load Boot Loader code then write to Flash via TFTP.

You choosed 4

0

eth_register  
Eth0 (10/100-M)
enetvar=ethaddr,Eth addr:00:0C:43:09:26:BB

eth_current->name = Eth0 (10/100-M)


4: System Enter Boot Command Line Interface.

U-Boot 1.1.3 (May 31 2012 - 20:54:08)
RT3052 # setenv serverip 192.168.1.100
RT3052 # tftpboot 0x80100000 tftpd-uboot.bin

netboot_common, argc= 3
*************buf = 0x8118ba20
**********NexTxPacket = 811a3bc0

NetTxPacket = 0x811A3BC0

NetRxPackets[0] = 0x811A41C0

NetRxPackets[1] = 0x811A47C0

NetRxPackets[2] = 0x811A4DC0

NetRxPackets[3] = 0x811A53C0

NetRxPackets[4] = 0x811A59C0

NetRxPackets[5] = 0x811A5FC0

NetRxPackets[6] = 0x811A65C0

NetRxPackets[7] = 0x811A6BC0

NetRxPackets[8] = 0x811A71C0

NetRxPackets[9] = 0x811A77C0

NetRxPackets[10] = 0x811A7DC0

NetRxPackets[11] = 0x811A83C0

NetRxPackets[12] = 0x811A89C0

NetRxPackets[13] = 0x811A8FC0

NetRxPackets[14] = 0x811A95C0

NetRxPackets[15] = 0x811A9BC0

NetRxPackets[16] = 0x811AA1C0

NetRxPackets[17] = 0x811AA7C0

NetRxPackets[18] = 0x811AADC0

NetRxPackets[19] = 0x811AB3C0

NetRxPackets[20] = 0x811AB9C0

NetRxPackets[21] = 0x811ABFC0

NetRxPackets[22] = 0x811AC5C0

NetRxPackets[23] = 0x811ACBC0

KSEG1ADDR(NetTxPacket) = 0xA11A3BC0

NetLoop,call eth_halt !

NetLoop,call eth_init !
Trying Eth0 (10/100-M)

Waitting for RX_DMA_BUSY status Start... done


Header Payload scatter function is Disable !!

ETH_STATE_ACTIVE!!
Using Eth0 (10/100-M) device
TFTP from server 192.168.1.100; our IP address is 192.168.1.1
Filename 'tftpd-uboot.bin'.

TIMEOUT_COUNT=10,Load address: 0x80100000
Loading: T T T T T T T T T T
Retry count exceeded; starting again
Trying Eth0 (10/100-M)

ETH_STATE_ACTIVE!!

ArpTimeoutCheck

ArpTimeoutCheck
Got ARP REQUEST, return our IP
test print
192.168.1.1test print NetServerIP
192.168.1.100checksum bad
checksum bad
Using Eth0 (10/100-M) device
TFTP from server 192.168.1.100; our IP address is 192.168.1.1
Filename 'tftpd-uboot.bin'.

TIMEOUT_COUNT=10,Load address: 0x80100000
Loading: checksum bad
checksum bad
checksum bad
T T Got ARP REQUEST, return our IP
test print
192.168.1.1test print NetServerIP
192.168.1.100T T T T Got ARP REQUEST, return our IP
test print
192.168.1.1test print NetServerIP
192.168.1.100T T T T
Retry count exceeded; starting again
Trying Eth0 (10/100-M)

ETH_STATE_ACTIVE!!

zwjwjz

本机IP：192.168.1.100   255.255.255.0，未设置网关，按教程来的啊