找回密码
 立即注册

QQ登录

只需一步,快速开始

搜索
广告投放联系QQ68610888
查看: 5840|回复: 6

EA6700 刷ATT奇怪的问题

[复制链接]
发表于 2017-8-23 11:24 | 显示全部楼层 |阅读模式
本帖最后由 smallfish001 于 2017-8-23 11:27 编辑

前两天按照教程刷了EA6700-AT-ARM-3.4-140-AIO-64K.trx这个固件,ATT官方的,设置了宽带和无线,使用正常,


因为CPU温度偏高,到75了,网上买了个小涡轮风扇,昨天拆机加好了,但是启动以后搜不到无线信号了,进入TT一看,只认出来5G网卡,2.4G的丢了
开始各种怀疑,焊风扇的时候把4331搞挂了?不对啊,电源口离4331那么远不应该啊,然后TT里清除NVRAM,重启后找到2.4G了,这是什么鬼?
再恢复设置(TT的设置备份过),重启后又找不到2.4G了,晕了,看TT里有个恢复出厂设置(清除NVRAM上面的选项),恢复了一下,起来后,有线能获得IP,但是网页访问不了,也PING不通,砖了?没办法,捅RESET试试,没用,断电后重启,恢复到官方固件了(应该是我当时刷的时候只刷了一遍,另一个还是官方固件),又重刷TT,再重新手动配置好。断电后,恢复路由盖子,


再通电,进入TT,还是只认出来5G网卡,再清除NVRAM,重新配置,恢复正常。


现在想来,TT配置好后就不能断电,只要断电就找不到2.4G网卡,像是NVRAM丢失,何解?硬件故障?有用这个固件的吗?


昨天晚上搞到1点多,等今天回家再换固件试试,还是怀疑固件问题,或者无线设置的BUG
我的恩山、我的无线 The best wifi forum is right here.
发表于 2017-8-23 11:52 | 显示全部楼层
折腾吧666666

点评

不帮忙分析问题,还偷着乐  详情 回复 发表于 2017-8-23 12:34
我的恩山、我的无线 The best wifi forum is right here.
回复

使用道具 举报

 楼主| 发表于 2017-8-23 12:34 | 显示全部楼层

不帮忙分析问题,还偷着乐
我的恩山、我的无线 The best wifi forum is right here.
回复

使用道具 举报

发表于 2017-8-23 22:07 | 显示全部楼层
这个问题在英文论坛上早就被讨论过了。Linksys EA6700/6900有个32k nvram的大bug,当配置文件大小超过32k后,重启时配置文件会随机丢失。最终解决方案刷CFE(相当于电脑主板的BIOS)。以下英文贴有详细介绍。
http://www.linksysinfo.org/index ... er-on-tomato.73655/
我的恩山、我的无线 The best wifi forum is right here.
回复

使用道具 举报

发表于 2017-8-24 09:50 | 显示全部楼层
32K NVRAM bug ,有个教程可以刷CFE解决,我已经搞定了
我的恩山、我的无线 The best wifi forum is right here.
回复

使用道具 举报

发表于 2017-8-24 09:52 | 显示全部楼层
我的恩山、我的无线 The best wifi forum is right here.
回复

使用道具 举报

发表于 2021-5-27 16:49 | 显示全部楼层
我EA6500V2刷死了,改了SPI,CFE进去是命令行模式,这个怎么刷机呀,还 是说EA6500不支持SPI进CFE或mini系统
CFE> help
Available commands:

et                  Broadcom Ethernet utility.
devinfo             devinfo utility.
nvram               NVRAM utility.
reboot              Reboot.
mfg                 Manufacture test
set console         Change the active console device
loop                Loop a command
flash               Update a flash memory device
memtest             Test memory.
f                   Fill contents of memory.
e                   Modify contents of memory.
d                   Dump memory.
u                   Disassemble instructions.
batch               Load a batch file into memory and execute it
go                  Verify and boot OS image.
boot                Load an executable file into memory and execute it
load                Load an executable file into memory without executing it
save                Save a region of memory to a remote file via TFTP
ping                Ping a remote IP host.
arp                 Display or modify the ARP Table
ifconfig            Configure the Ethernet interface
show clocks         Show current values of the clocks.
show heap           Display information about CFE's heap
show memory         Display the system physical memory map.
show devices        Display information about the installed devices.
unsetenv            Delete an environment variable.
printenv            Display the environment variables
setenv              Set an environment variable.
help                Obtain help for CFE commands

For more information about a command, enter 'help command-name'
*** command status = 0
CFE> show devices
Device Name          Description
-------------------  ---------------------------------------------------------
uart0                NS16550 UART at 0x18000300
uart1                NS16550 UART at 0x18000400
*** command status = 0
CFE> printenv
Variable Name        Value
-------------------- --------------------------------------------------
BOOT_CONSOLE         uart0
CFE_VERSION          1.0.37
CFE_BOARDNAME        BCM947XX
CFE_MEMORYSIZE       262144
STARTUP              go;
*** command status = 0
CFE> nvram show
pmon_ver=CFE 6.39.163.39 (r394801)
nvram_space=65536
sdram_config=0x0000
sdram_refresh=0x8040
sdram_ncdl=0x00000000
sdram_init=0x0419
size: 154 bytes (65382 left)
*** command status = 0
CFE> flash

     flash [options] filename [flashdevice]
     
     Copies data from a source file name or device to a flash memory device.
     The source device can be a disk file (FAT filesystem), a remote file
     (TFTP) or a flash device.  The destination device may be a flash or eeprom.
     If the destination device is your boot flash (usually flash0), the flash
     command will restart the firmware after the flash update is complete

     -noerase     Don't erase flash before writing
     -offset=*    Begin programming at this offset in the flash device
     -size=*      Size of source device when programming from flash to flash
     -noheader    Override header verification, flash binary without checking
     -forceflash  Dangerous Command, Don't use if you don't know what you do
     -erase       Erase the partition, can set the  offset and length
     -mem         Use memory as source instead of a device

*** command status = -2
CFE> flash -noerase -noheader 192.168.1.2:128.bin flash1.trx
flash1.trx: Device not found
*** command status = -6
CFE>
我的恩山、我的无线 The best wifi forum is right here.
回复

使用道具 举报

您需要登录后才可以回帖 登录 | 立即注册

本版积分规则

有疑问请添加管理员QQ86788181|手机版|小黑屋|Archiver|恩山无线论坛(常州市恩山计算机开发有限公司版权所有) ( 苏ICP备05084872号 )

GMT+8, 2024-3-29 06:56

Powered by Discuz! X3.5

© 2001-2024 Discuz! Team.

| 江苏省互联网有害信息举报中心 举报信箱:js12377 | @jischina.com.cn 举报电话:025-88802724 本站不良内容举报信箱:68610888@qq.com 举报电话:0519-86695797

快速回复 返回顶部 返回列表