找回密码
 立即注册

QQ登录

只需一步,快速开始

搜索
广告投放联系QQ68610888
查看: 34873|回复: 44

闲来无事拆改水星MERCURY MAC2600R V1路由器刷PANDORABOX固件

[复制链接]
发表于 2017-10-22 20:31 | 显示全部楼层 |阅读模式
本帖最后由 vip2002 于 2017-10-22 21:13 编辑

闲鱼叼取一台MERCURY MAC2600R V1 路由器,成色很新



1、经有兄弟拆改过此机,这里不再累赘,具体可以见 简单测试水星MAC2600R+拆机 https://www.right.com.cn/forum/thread-200153-1-1.html

2、补充网上欠缺的部分拆机图



上图为背板PCB概貌



3、上图是借用的原拆改贴上注明的TTL接线方式。因为要拆散热片,本人手笨,TTL插座焊接普遍难伺候,索性就直接拿下8MB SPI FLASH上编程器改了

本帖子中包含更多资源

您需要 登录 才可以下载或查看,没有账号?立即注册

×
我的恩山、我的无线 The best wifi forum is right here.
 楼主| 发表于 2017-10-22 20:31 | 显示全部楼层
本帖最后由 vip2002 于 2017-10-22 21:15 编辑

第二楼,拼接制作固件过程

1、不熟悉MT7621A/AT编程器固件各分区,经朋友在线指导,截取保存了网卡和无线设置的EEPROM文件(类似于高通的art文件),长度64kB

2、Breed启动文件选取破费周折。没有专门的breed-mt7621-mac2600rv1 版本,把Hackpascal 9月21日发表的都试了个遍,选取了迅雷时光机适用版本breed-mt7621-xunlei-timeplug,按reset键能清除设置并复位启动



3、pandorabox固件的来源 http://downloads.pandorabox.com.cn/pandorabox/17.09/targets/ralink/mt7621/



4、选取固件版本,让我吃足苦头!最新的9月27日版本有很多问题,足足耗费了4-5小时反复调整才确认,暂采用最早的版本试验

5、最后拼接成的编程器固件另外提供,eeprom 点击此处下载

本帖子中包含更多资源

您需要 登录 才可以下载或查看,没有账号?立即注册

×

点评

你那2017的breed 上传一分。2018的不行,  详情 回复 发表于 2019-9-18 21:07
我的恩山、我的无线 The best wifi forum is right here.
回复

使用道具 举报

 楼主| 发表于 2017-10-22 20:32 | 显示全部楼层
本帖最后由 vip2002 于 2017-10-22 20:56 编辑

第三楼,测试结果

1、刷入后pandorabox概况画面



2、wifi 设置和无线网速



3、手机端接入速度(高通820芯片组,AC 2-streams )



4、手机端用ucweb浏览器测速,上海电信200M光纤接入


本帖子中包含更多资源

您需要 登录 才可以下载或查看,没有账号?立即注册

×
我的恩山、我的无线 The best wifi forum is right here.
回复

使用道具 举报

发表于 2017-10-22 20:37 | 显示全部楼层
8m真的太抠门了....

点评

暂时够用,关键是没有USB扩展接口情况下,只作为无线路由器、无线AP够用了  详情 回复 发表于 2017-10-22 21:22
我的恩山、我的无线 The best wifi forum is right here.
回复

使用道具 举报

 楼主| 发表于 2017-10-22 20:57 | 显示全部楼层
本帖最后由 vip2002 于 2017-10-22 21:20 编辑

第四楼,问题和讨论
1、9月27日pandorabox版本存在问题:
(1)默认IP为192.168.1.1,修改为192.168.1.x 或192.168.0.1,第2次启动恢复到默认IP
(2)2.4G/5.8G WIFI各项参数设置,重启失效
(3)其他待发现
开始在编程器刷写固件有读写错误,所以总怀疑是FLASHROM在有坏块无法保存参数,没怀疑最新版pandorabox固件存在问题,浪费了很多时间

2、功耗
MT7621A功耗较低,稳定功耗在4.5W左右,网络测速过程中约5.4-6.0W之间,厂家配的电源适配器是12V1.5A,没有USB接口耗电情况下裕度较充沛


3、USB2.0扩展口的前途,烦劳大师们看看,是否有希望找到引出线
(1)MT7621AT背部PCB局部




(2)PCB局部再放大




4、最后附上启动顺序boot sequence ,供后续讨论和诸位参考用途

[    0.000000] Initializing cgroup subsys cpuset
[    0.000000] Initializing cgroup subsys cpu
[    0.000000] Linux version 3.14.79 (lintel@PandoraBox-Server) (gcc version 4.8.3 (PandoraBox/Linaro GCC 4.8-2014.04 2017-09-16-git-a9e035b) ) #0 SMP Sat Sep 16 15:00:56 2017
[    0.000000] MT7621: MPLL enabled.
[    0.000000] PandoraBox CPUID Module for Ralink/MTK SoC v1.1.
[    0.000000] MediaTek MT7621 pkg:BGA rev:1 eco:3 CPU:880MHz Bus:220MHz Uart:50MHz
[    0.000000] CPU running in Little Endian
[    0.000000] Board VLANLLLW
[    0.000000] Flash:SPI 3byte Size: 8MB
[    0.000000] DRAM: 128MB DDR3 16 bits
[    0.000000] Kernel Support [PCI] [USB]
[    0.000000] prom memory:128MB
[    0.000000] MT7621: PCIe reset
[    0.000000] GCMP present
[    0.000000] bootconsole [early0] enabled
[    0.000000] CPU0 revision is: 0001992f (MIPS 1004Kc)
[    0.000000] Software DMA cache coherency
[    0.000000] Determined physical RAM map:
[    0.000000]  memory: 08000000 @ 00000000 (usable)
[    0.000000] Zone ranges:
[    0.000000]   DMA      [mem 0x00000000-0x00ffffff]
[    0.000000]   Normal   [mem 0x01000000-0x07ffffff]
[    0.000000]   HighMem  empty
[    0.000000] Movable zone start for each node
[    0.000000] Early memory node ranges
[    0.000000]   node   0: [mem 0x00000000-0x07ffffff]
[    0.000000] On node 0 totalpages: 32768
[    0.000000] free_area_init_node: node 0, pgdat 80433960, node_mem_map 81000000
[    0.000000]   DMA zone: 32 pages used for memmap
[    0.000000]   DMA zone: 0 pages reserved
[    0.000000]   DMA zone: 4096 pages, LIFO batch:0
[    0.000000]   Normal zone: 224 pages used for memmap
[    0.000000]   Normal zone: 28672 pages, LIFO batch:7
[    0.000000] Detected 3 available secondary CPU(s)
[    0.000000] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
[    0.000000] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
[    0.000000] MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
[    0.000000] PERCPU: Embedded 7 pages/cpu @81103000 s5792 r8192 d14688 u32768
[    0.000000] pcpu-alloc: s5792 r8192 d14688 u32768 alloc=8*4096
[    0.000000] pcpu-alloc: [0] 0 [0] 1 [0] 2 [0] 3
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 32512
[    0.000000] Kernel command line: pause_on_oops=10 noresume  board=MAC2600R  console=ttyS1,115200 rootfstype=squashfs,jffs2
[    0.000000] PID hash table entries: 512 (order: -1, 2048 bytes)
[    0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
[    0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
[    0.000000] Writing ErrCtl register=00000040
[    0.000000] Readback ErrCtl register=00000040
[    0.000000] Memory: 124792K/131072K available (3453K kernel code, 221K rwdata, 768K rodata, 216K init, 314K bss, 6280K reserved, 0K highmem)
[    0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
[    0.000000] Hierarchical RCU implementation.
[    0.000000] NR_IRQS:256
[    0.000000] GIC: Revision 3.0
[    0.000000] Setup MT7621 IRQs...Done
[    0.000000] console [ttyS1] enabled
[    0.004000] bootconsole [early0] disabled
[    0.008000] Calibrating delay loop... 577.53 BogoMIPS (lpj=1155072)
[    0.036000] pid_max: default: 32768 minimum: 301
[    0.040000] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.044000] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.048000] Initializing cgroup subsys devices
[    0.052000] Initializing cgroup subsys freezer
[    0.056000] Initializing cgroup subsys net_cls
[    0.060000] Initializing cgroup subsys blkio
[    0.064000] Initializing cgroup subsys net_prio
[    0.068000] CPU1 :Booting up...done!
[    0.072000] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
[    0.072000] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
[    0.072000] MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
[    0.072000] CPU1 revision is: 0001992f (MIPS 1004Kc)
[    0.104000] Synchronize counters for CPU 1: done.
[    0.108000] CPU2 :Booting up...done!
[    0.112000] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
[    0.112000] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
[    0.112000] MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
[    0.112000] CPU2 revision is: 0001992f (MIPS 1004Kc)
[    0.144000] Synchronize counters for CPU 2: done.
[    0.148000] CPU3 :Booting up...done!
[    0.152000] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
[    0.152000] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
[    0.152000] MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
[    0.152000] CPU3 revision is: 0001992f (MIPS 1004Kc)
[    0.180000] Synchronize counters for CPU 3: done.
[    0.184000] Brought up 4 CPUs
[    0.188000] pinctrl core: initialized pinctrl subsystem
[    0.192000] NET: Registered protocol family 16
[    0.196000] Ralink/MTK BootROM maped.
[    0.200000] Ralink/MTK device hooks driver. (C) 2017 PandoraBox Team
[    0.204000] Generic Ralink/MTK Register Operation API (c) 2013-2015 PandoraBox Team
[    0.208000] SYSCTL maped at address:0xbe000000
[    0.212000] MEMCTRL maped at address:0xbe005000
[    0.216000] RFCTRL maped at address:0xbe180000
[    0.220000] Generic GPIO Driver for MediaTek MT7621 Board. (C) 2013-2015 PandoraBox Team
[    0.224000] MT7621-GPIO0:registering 32 irq handlers
[    0.228000] MT7621-GPIO1:registering 32 irq handlers
[    0.232000] MT7621-GPIO3:registering 32 irq handlers
[    0.236000] MIPS: machine is Mercury MAC2600R
[    0.240000] ralink_register_flash:SPI Flash.
[    0.244000] Ralink/MTK PinCtrl registered.
[    0.248000] MT762x PCIe PHY initialize
[    1.648000] PCIE2 no card, disable it(RST&CLK)
[    1.652000] PCIE0:link up
[    1.652000] PCIE1:link up
[    1.656000] PCIE2:link down
[    1.656000] mt762x-pcie:register pci controller
[    1.660000] FPU Affinity set after 4664 emulations
[    1.668000] bio: create slab <bio-0> at 0
[    1.672000] PCI host bridge to bus 0000:00
[    1.676000] pci_bus 0000:00: root bus resource [mem 0x60000000-0x6fffffff]
[    1.680000] pci_bus 0000:00: root bus resource [io  0x1e160000-0x1e16ffff]
[    1.684000] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]
[    1.688000] pci 0000:00:00.0: [0e8d:0801] type 01 class 0x060400
[    1.688000] pci 0000:00:00.0: reg 0x10: [mem 0x00000000-0x7fffffff]
[    1.688000] pci 0000:00:00.0: reg 0x14: [mem 0x60200000-0x6020ffff]
[    1.688000] pci 0000:00:00.0: supports D1
[    1.688000] pci 0000:00:00.0: PME# supported from D0 D1 D3hot
[    1.688000] pci 0000:00:01.0: [0e8d:0801] type 01 class 0x060400
[    1.688000] pci 0000:00:01.0: reg 0x10: [mem 0x00000000-0x7fffffff]
[    1.688000] pci 0000:00:01.0: reg 0x14: [mem 0x60210000-0x6021ffff]
[    1.688000] pci 0000:00:01.0: supports D1
[    1.688000] pci 0000:00:01.0: PME# supported from D0 D1 D3hot
[    1.688000] pci 0000:01:00.0: [14c3:7615] type 00 class 0x000280
[    1.688000] pci 0000:01:00.0: reg 0x10: [mem 0x00000000-0x000fffff 64bit]
[    1.688000] pci_bus 0000:01: busn_res: [bus 01-ff] end is updated to 01
[    1.688000] pci 0000:02:00.0: [14c3:7615] type 00 class 0x000280
[    1.688000] pci 0000:02:00.0: reg 0x10: [mem 0x00000000-0x000fffff 64bit]
[    1.688000] pci_bus 0000:02: busn_res: [bus 02-ff] end is updated to 02
[    1.688000] pci_bus 0000:00: busn_res: [bus 00-ff] end is updated to 02
[    1.688000] pci 0000:00:00.0: BAR 0: can't assign mem (size 0x80000000)
[    1.692000] pci 0000:00:01.0: BAR 0: can't assign mem (size 0x80000000)
[    1.696000] pci 0000:00:00.0: BAR 8: assigned [mem 0x60000000-0x600fffff]
[    1.700000] pci 0000:00:01.0: BAR 8: assigned [mem 0x60100000-0x601fffff]
[    1.704000] pci 0000:00:00.0: BAR 1: assigned [mem 0x60200000-0x6020ffff]
[    1.708000] pci 0000:00:01.0: BAR 1: assigned [mem 0x60210000-0x6021ffff]
[    1.712000] pci 0000:01:00.0: BAR 0: assigned [mem 0x60000000-0x600fffff 64bit]
[    1.716000] pci 0000:00:00.0: PCI bridge to [bus 01]
[    1.720000] pci 0000:00:00.0:   bridge window [mem 0x60000000-0x600fffff]
[    1.724000] pci 0000:02:00.0: BAR 0: assigned [mem 0x60100000-0x601fffff 64bit]
[    1.728000] pci 0000:00:01.0: PCI bridge to [bus 02]
[    1.732000] pci 0000:00:01.0:   bridge window [mem 0x60100000-0x601fffff]
[    1.736000] PCI Bus 1 slot 0 mapping to IRQ4.
[    1.740000] PCI Bus 2 slot 1 mapping to IRQ24.
[    1.744000] Generic PinCtrl Driver for MediaTek MT7621 Board. (C) 2013-2015 PandoraBox Team
[    1.748000] PINCTRL:add 31 pins for MT7621-PINCTRL0.
[    1.752000] PINCTRL:add 31 pins for MT7621-PINCTRL1.
[    1.756000] PINCTRL:add 31 pins for MT7621-PINCTRL2.
[    1.760000] GPIO_MODE_REG:0x485AC
[    1.760000] Switched to clocksource Ralink/MTK 50kHz Systick timer
[    1.764000] PandoraBox SPLICE initialized. rcv 87db0000 (sz:384) kvec 87d60000 (sz:128) per 4 core
[    1.776000] NET: Registered protocol family 2
[    1.784000] TCP established hash table entries: 1024 (order: 0, 4096 bytes)
[    1.788000] TCP bind hash table entries: 1024 (order: 1, 8192 bytes)
[    1.796000] TCP: Hash tables configured (established 1024 bind 1024)
[    1.804000] TCP: reno registered
[    1.804000] UDP hash table entries: 256 (order: 1, 8192 bytes)
[    1.812000] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
[    1.816000] NET: Registered protocol family 1
[    1.824000] PCI: CLS 80 bytes, default 32
[    1.824000] Ralink SoC clocks api init.
[    1.828000] mips hpt frequency:440000000HZ
[    1.920000] 4 CPUs re-calibrate udelay(lpj = 1167360)
[    1.928000] Ralink/MTK APSoC GPIO Resource maped.
[    1.932000] Load Kernel WDG Timer Module
[    1.936000] Load Ralink Timer0 Module
[    1.940000] Load Ralink Timer2 Module
[    1.944000] xHCI host registered
[    1.952000] futex hash table entries: 1024 (order: 3, 32768 bytes)
[    1.976000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    1.980000] jffs2: version 2.2 (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[    1.992000] msgmni has been set to 243
[    1.996000] io scheduler noop registered (default)
[    2.004000] io scheduler deadline registered
[    2.008000] io scheduler cfq registered
[    2.012000] io scheduler bfq registered
[    2.016000] BFQ I/O-scheduler: v7r8
[    2.020000] Serial: 8250/16550 driver, 3 ports, IRQ sharing disabled
[    2.024000] serial8250: ttyS0 at MMIO 0x1e000d00 (irq = 27, base_baud = 3125000) is a 16550A
[    2.036000] serial8250: ttyS1 at MMIO 0x1e000c00 (irq = 26, base_baud = 3125000) is a 16550A
[    2.044000] serial8250: ttyS2 at MMIO 0x1e000e00 (irq = 28, base_baud = 3125000) is a 16550A
[    2.064000] brd: module loaded
[    2.072000] PandoraBox MT7621/28 SPI flash driver, SPI_ClK: 44MHz
[    2.076000] device id : ef 40 17 0 0 (40170000)
[    2.080000] SPI flash chip: W25Q64BV (ef 40170000) (8192 Kbytes)
[    2.088000] Creating 5 MTD partitions on "raspi":
[    2.092000] 0x000000000000-0x000000030000 : "u-boot"
[    2.100000] 0x000000030000-0x000000040000 : "u-boot-env"
[    2.108000] 0x000000040000-0x000000050000 : "Factory"
[    2.112000] 0x000000000000-0x000000800000 : "fullflash"
[    2.120000] 0x000000050000-0x000002000000 : "firmware"
[    2.124000] mtd: partition "firmware" extends beyond the end of device "raspi" -- size truncated to 0x7b0000
[    2.144000] 3 uimage-fw partitions found on MTD device firmware
[    2.152000] 0x000000050000-0x0000001c4960 : "kernel"
[    2.156000] mtd: partition "kernel" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
[    2.172000] 0x0000001c4960-0x0000007e0000 : "rootfs"
[    2.176000] mtd: partition "rootfs" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
[    2.188000] mtd: device 6 (rootfs) set to be root filesystem
[    2.196000] 1 squashfs-split partitions found on MTD device rootfs
[    2.200000] 0x000000760000-0x0000007e0000 : "rootfs_data"
[    2.208000] 0x0000007e0000-0x000000800000 : "panic_oops"
[    2.216000] mtdoops: ready 0, 1 (no erase)
[    2.216000] mtdoops: Attached to MTD device 8
[    2.220000] rdm_major = 250
[    2.224000] EEPROM:Read from [Factory] offset 0xe000,length 0x6.
[    2.236000] Ralink APSoC Ethernet Driver v3.2.4 (raeth)
[    2.244000] raeth: PDMA RX ring 512, QDMA TX pool 1024. Max packet size 1536
[    2.252000] raeth: NAPI & GRO support, weight 64
[    2.256000] raeth: Byte Queue Limits (BQL) support
[    2.260000] raeth: GMAC reset
[    2.264000] mt762x-gsw switch driver registered
[    2.268000] mt762x-gsw default vlans:wllll
[    2.280000] TCP: cubic registered
[    2.284000] TCP: westwood registered
[    2.288000] TCP: hybla registered
[    2.292000] TCP: htcp registered
[    2.292000] NET: Registered protocol family 17
[    2.296000] Bridge firewalling registered
[    2.300000] 8021q: 802.1Q VLAN Support v1.8
[    2.308000] PandoraBox Mass Storage accelerater v1.2
[    2.312000] Generic NVRAM Driver for MediaTek Board. (c) 2013-2015 PandoraBox Team.
[    2.320000] NVRAM driver (major 248) installed
[    2.324000] registered taskstats version 1
[    2.332000] UBIFS error (pid 1): ubifs_mount: cannot open "ubi0:rootfs", error -19
[    2.344000] VFS: Mounted root (squashfs filesystem) readonly on device 31:6.
[    2.352000] Freeing unused kernel memory: 216K (8045a000 - 80490000)
[    3.124000] init: Console is alive
[    3.572000] random: nonblocking pool is initialized
[    5.468000] PandoraBox Button Driver init
[    5.472000] Button [reset] mapped to GPIO8 and IRQ64
[    5.500000] init: - preinit -
[    6.692000] raeth: HW IP/TCP/UDP checksum RX/TX offload enabled
[    6.700000] raeth: HW Scatter/Gather TX offload enabled
[    6.704000] raeth: HW TCP segmentation offload (TSO) enabled
[    6.708000] raeth: NAPI mode enabled
[    6.712000] raeth: NAPI GRO offload enabled
[    6.716000] raeth: Frame Engine reset
[    6.720000] raeth: QDMA init
[    6.724000] raeth: MT7530 GSW initializing
[    9.004000] raeth: port 0 link up (1000Mbps/Full duplex)
[    9.956000] jffs2: notice: (447) jffs2_build_xattr_subsystem: complete building xattr subsystem, 2 of xdatum (1 unchecked, 1 orphan) and 40 of xref (0 dead, 4 orphan) found.
[    9.972000] mount_root: switching to jffs2 overlay
[    9.980000] urandom-seed: Seed file not found (/etc/urandom.seed)
[   10.056000] raeth: port 0 link down
[   10.096000] procd: - early -
[   10.188000] procd: cannot set group tty for /dev/ttyS0
[   10.196000] procd: cannot set group tty for /dev/ttyS1
[   10.200000] procd: cannot set group tty for /dev/ttyS2
[   10.724000] procd: - ubus -
[   10.784000] procd: - init -
[   11.068000] NET: Registered protocol family 10
[   11.080000] zram: Created 1 device(s) ...
[   11.092000] NET: Registered protocol family 8
[   11.096000] NET: Registered protocol family 20
[   11.116000] loop: module loaded
[   11.120000] tun: Universal TUN/TAP device driver, 1.6
[   11.128000] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
[   11.136000] l2tp_core: L2TP core driver, V2.0
[   11.144000] l2tp_netlink: L2TP netlink interface
[   11.156000] gre: GRE over IPv4 demultiplexor driver
[   11.164000] ip_gre: GRE over IPv4 tunneling driver
[   11.172000] gpiodev: gpio device registered with major 247
[   11.184000] PPP generic driver version 2.4.2
[   11.200000] nf_conntrack version 0.5.0 (1953 buckets, 7812 max)
[   11.212000] ip6_tables: (C) 2000-2006 Netfilter Core Team
[   11.224000] Netfilter messages via NETLINK v0.30.
[   11.232000] ip_set: protocol 6
[   11.272000] i2c /dev entries driver
[   11.284000] u32 classifier
[   11.288000]     input device check on
[   11.292000]     Actions configured
[   11.296000] Mirror/redirect action on
[   11.332000] PandoraBox IP Bandwidth load.
[   11.536000] register mt_drv
[   11.552000]
[   11.552000]
[   11.552000] === pAd = c0981000, size = 3616856 ===
[   11.552000]
[   11.564000] <-- RTMPAllocAdapterBlock, Status=0
[   11.568000] pAd->ciHif.CSRBaseAddress =0xc0880000, csr_addr=0xc0880000!
[   11.576000] RTMPInitPCIeDevice():device_id=0x7615
[   11.580000] DriverOwn()::Try to Clear FW Own...
[   11.916000] DriverOwn()::Success to clear FW Own
[   11.920000] mt_pci_chip_cfg(): HWVer=0x8a10, FWVer=0x8a10, pAd->ChipID=0x7615
[   11.928000] mt_pci_chip_cfg(): HIF_SYS_REV=0x76150001
[   11.932000] RtmpChipOpsHook(492): Not support for HIF_MT yet! MACVersion=0x0
[   11.940000] mt7615_init()-->
[   11.940000] Use 1st ePAeLNA default bin.
[   11.944000] <--mt7615_init()
[   11.948000] ChipOpsMCUHook
[   11.956000] cut_through_token_list_init(): TokenList inited done!id_head/tail=0/4096
[   11.964000] cut_through_token_list_init(): 85f50108,85f50108
[   11.972000] cut_through_token_list_init(): TokenList inited done!id_head/tail=0/4096
[   11.980000] cut_through_token_list_init(): 85f50118,85f50118
[   11.984000] <-- RTMPAllocTxRxRingMemory, Status=0
[   12.008000]
[   12.008000]
[   12.008000] === pAd = c0e01000, size = 3616856 ===
[   12.008000]
[   12.020000] <-- RTMPAllocAdapterBlock, Status=0
[   12.024000] pAd->ciHif.CSRBaseAddress =0xc0d00000, csr_addr=0xc0d00000!
[   12.032000] RTMPInitPCIeDevice():device_id=0x7615
[   12.036000] DriverOwn()::Try to Clear FW Own...
[   12.364000] DriverOwn()::Success to clear FW Own
[   12.368000] mt_pci_chip_cfg(): HWVer=0x8a10, FWVer=0x8a10, pAd->ChipID=0x7615
[   12.376000] mt_pci_chip_cfg(): HIF_SYS_REV=0x76150001
[   12.380000] RtmpChipOpsHook(492): Not support for HIF_MT yet! MACVersion=0x0
[   12.388000] mt7615_init()-->
[   12.392000] Use 2nd ePAeLNA default bin.
[   12.396000] <--mt7615_init()
[   12.396000] ChipOpsMCUHook
[   12.408000] cut_through_token_list_init(): TokenList inited done!id_head/tail=0/4096
[   12.416000] cut_through_token_list_init(): 807b8708,807b8708
[   12.424000] cut_through_token_list_init(): TokenList inited done!id_head/tail=0/4096
[   12.432000] cut_through_token_list_init(): 807b8718,807b8718
[   12.436000] <-- RTMPAllocTxRxRingMemory, Status=0
[   12.456000] ip_tables: (C) 2000-2006 Netfilter Core Team, NAT Type:Symmetric Cone
[   12.508000] ctnetlink v0.93: registering with nfnetlink.
[   12.580000] PPP MPPE Compression module registered
[   12.588000] NET: Registered protocol family 24
[   12.596000] p p t p driver version 0.8.5
[   12.656000] xt_time: kernel timezone is -0000
[   12.668000] l2tp_ppp: PPPoL2TP kernel driver, V2.0
[   15.904000] raeth: HW IP/TCP/UDP checksum RX/TX offload enabled
[   15.908000] raeth: HW Scatter/Gather TX offload enabled
[   15.912000] raeth: HW TCP segmentation offload (TSO) enabled
[   15.920000] raeth: NAPI mode enabled
[   15.924000] raeth: NAPI GRO offload enabled
[   15.928000] raeth: Frame Engine reset
[   15.932000] raeth: QDMA init
[   15.936000] raeth: MT7530 GSW initializing
[   15.944000] device eth0 entered promiscuous mode
[   15.952000] br-lan: port 1(eth0) entered forwarding state
[   15.956000] br-lan: port 1(eth0) entered forwarding state
[   15.980000] device eth0.1 entered promiscuous mode
[   15.984000] br-lan: port 2(eth0.1) entered forwarding state
[   15.992000] br-lan: port 2(eth0.1) entered forwarding state
[   16.008000] device eth0.2 entered promiscuous mode
[   16.012000] br-lan: port 3(eth0.2) entered forwarding state
[   16.020000] br-lan: port 3(eth0.2) entered forwarding state
[   16.032000] IPv6: ADDRCONF(NETDEV_UP): teql0: link is not ready
[   16.088000] PandoraBox HW-NAT v2.52.0 Module Enabled, FoE Size: 16384
[   16.092000] PPE:IPv4 NAT offload for TCP proto default enabled
[   16.100000] PPE:IPv4 NAT offload for UDP proto enabled
[   16.104000] PPE:IPv4 NAT offload for WiFi/ExtIf enabled
[   16.108000] PPE:IPv6 routes offload enabled
[   16.112000] PPE:WAN_ID:2 LAN_ID:1
[   16.148000] IPv6: ADDRCONF(NETDEV_UP): teql0: link is not ready
[   16.488000] DriverOwn()::Return since already in Driver Own...
[   16.508000] SSID[0]=78a, EdcaIdx=0
[   16.516000] cfg_mode=14
[   16.520000] cfg_mode=14
[   16.520000] wmode_band_equal(): Band Equal!
[   16.528000] APEdca0
[   16.532000] APEdca1
[   16.536000] APEdca2
[   16.536000] APEdca3
[   16.540000] APSDCapable[0]=0
[   16.544000] APSDCapable[1]=0
[   16.548000] APSDCapable[2]=0
[   16.552000] APSDCapable[3]=0
[   16.552000] APSDCapable[4]=0
[   16.556000] APSDCapable[5]=0
[   16.560000] APSDCapable[6]=0
[   16.564000] APSDCapable[7]=0
[   16.564000] APSDCapable[8]=0
[   16.568000] APSDCapable[9]=0
[   16.572000] APSDCapable[10]=0
[   16.576000] APSDCapable[11]=0
[   16.576000] APSDCapable[12]=0
[   16.580000] APSDCapable[13]=0
[   16.584000] APSDCapable[14]=0
[   16.588000] APSDCapable[15]=0
[   16.588000] default ApCliAPSDCapable[0]=0
[   16.592000] default ApCliAPSDCapable[1]=0
[   16.600000] DfsZeroWait Support=0/0
[   16.604000] DfsZeroWaitCacTime=255/255
[   16.612000] [RTMPSetProfileParameters]Disable DFS/Zero wait=0/0
[   16.644000] [PMF]Set_PMFMFPC_Proc:: apidx=0, Desired MFPC=0
[   16.648000] [PMF]Set_PMFMFPR_Proc:: apidx=0, Desired MFPR=0
[   16.656000] [PMF]Set_PMFSHA256_Proc:: apidx=0, Desired PMFSHA256=0
[   16.680000] HT: Ext Channel = ABOVE
[   16.684000] HT: greenap_cap = 0
[   16.732000] WtcSetMaxStaNum: MaxStaNum:88, BssidNum:4, WdsNum:0, ApcliNum:2, MaxNumChipRept:32, MinMcastWcid:122
[   16.744000] Top Init Done!
[   16.748000] Use dev_alloc_skb
[   16.752000] RX[0] DESC a5730000 size = 8192
[   16.756000] RX[1] DESC a506a000 size = 8192
[   16.764000] Hif Init Done!
[   16.764000] ctl->txq = c116ffa0
[   16.768000] ctl->rxq = c116ffac
[   16.772000] ctl->ackq = c116ffb8
[   16.776000] ctl->kickq = c116ffc4
[   16.780000] ctl->tx_doneq = c116ffd0
[   16.784000] ctl->rx_doneq = c116ffdc
[   16.788000] mt7615_fw_prepare():FW(8a10), HW(8a10), CHIPID(7615))
[   16.792000] mt7615_fw_prepare(2356): MT7615_E3, USE E3 patch and ram code binary image
[   16.800000] AndesMTLoadRomMethodFwDlRing(1035), cap->rom_patch_len(10206)
[   16.808000] AndesRestartCheck: Current TOP_MISC2(0x1)
[   16.812000] AndesRestartCheck: (TOP_MISC2 = 1), ready to continue...RET(0)
[   16.820000] 20161013140927a
[   16.824000]
[   16.824000] platform =
[   16.828000] ALPS
[   16.828000] hw/sw version =
[   16.832000] 8a108a10
[   16.832000] patch version =
[   16.836000] 00000010
[   16.840000] Patch SEM Status=2
[   16.844000] MtCmdPatchSemGetret = 0)
[   16.844000]
[   16.844000] Patch is not ready && get semaphore success, SemStatus(2)
[   16.856000] EventGenericEventHandler: CMD Success
[   16.860000] MtCmdAddressLenReqret = 0)
[   16.864000] MtCmdPatchFinishReq
[   16.876000] EventGenericEventHandler: CMD Success
[   16.884000] Send checksum req..
[   16.884000] Patch SEM Status=3
[   16.888000] MtCmdPatchSemGetret = 0)
[   16.892000]
[   16.892000] Release patch semaphore, SemStatus(3)
[   16.900000] AndesMTEraseRomPatch
[   16.904000] WfMcuHwInit: Before NICLoadFirmware, check IcapMode=0
[   16.908000] AndesMTLoadFwMethodFwDlRing(809), cap->fw_len(460056)
[   16.916000] Build Date:_201702151653
[   16.920000] Build Date:_201702151653
[   16.924000] AndesRestartCheck: Current TOP_MISC2(0x1)
[   16.928000] AndesRestartCheck: (TOP_MISC2 = 1), ready to continue...RET(0)
[   16.936000] EventGenericEventHandler: CMD Success
[   16.940000] MtCmdAddressLenReqret = 0)
[   16.952000] EventGenericEventHandler: CMD Success
[   16.956000] MtCmdAddressLenReqret = 0)
[   16.960000] MtCmdFwStartReq: override = 1, address = 540672
[   16.972000] EventGenericEventHandler: CMD Success
[   16.976000] Build Date:_201612301011
[   16.980000] EventGenericEventHandler: CMD Success
[   16.984000] MtCmdAddressLenReqret = 0)
[   16.992000] MtCmdFwStartReq: override = 4, address = 0
[   17.060000] EventGenericEventHandler: CMD Success
[   17.100000] WfMcuHwInit: NICLoadFirmware OK, Check IcapMode=0
[   17.104000] MCU Init Done!
[   17.108000] efuse_probe: efuse = 10000212
[   17.112000] RtmpChipOpsEepromHook::e2p_type=2, inf_Type=5
[   17.120000] RtmpEepromGetDefault::e2p_dafault=1
[   17.124000] RtmpChipOpsEepromHook: E2P type(2), E2pAccessMode = 2, E2P default = 1
[   17.132000] NVM is FLASH mode. dev_idx [1] FLASH OFFSET [0x8000]
[   17.136000] EEPROM:Read from [Factory] offset 0x8000,length 0x400.
[   17.144000] EEPROM:Read from [Factory] offset 0x8400,length 0x2400.
[   17.152000] EEPROM:Read from [Factory] offset 0xa600,length 0x2400.
[   17.160000] EEPROM:Read from [Factory] offset 0xc460,length 0x2400.
[   17.336000] PandoraBox HW NAT v2.52.0 Module Disabled
[   17.380000] PandoraBox HW-NAT v2.52.0 Module Enabled, FoE Size: 16384
[   17.384000] PPE:IPv4 NAT offload for TCP proto default enabled
[   17.392000] PPE:IPv4 NAT offload for UDP proto enabled
[   17.396000] PPE:IPv4 NAT offload for WiFi/ExtIf enabled
[   17.400000] PPE:IPv6 routes offload enabled
[   17.404000] PPE:WAN_ID:2 LAN_ID:1
[   17.960000] br-lan: port 1(eth0) entered forwarding state
[   17.996000] br-lan: port 2(eth0.1) entered forwarding state
[   18.024000] br-lan: port 3(eth0.2) entered forwarding state
[   18.288000] raeth: port 0 link up (1000Mbps/Full duplex)
[   25.416000] Country Region from e2p = 1
[   25.420000] mt7615_antenna_default_reset(): TxPath = 4, RxPath = 4
[   25.424000] rtmp_read_txpwr_from_eeprom(224): Don't Support this now!
[   25.432000] RTMPReadTxPwrPerRate(1385): Don't Support this now!
[   25.436000] RcRadioInit(): DbdcMode=0, ConcurrentBand=1
[   25.444000] RcRadioInit(): pRadioCtrl=87d1c448,Band=0,rfcap=3,channel=1,PhyMode=2
[   25.448000] MtCmdSetDbdcCtrlret = 0)
[   25.452000] Band Rf: 1, Phy Mode: 2
[   25.456000] AntCfgInit(2616): Not support for HIF_MT yet!
[   25.464000] MtSingleSkuLoadParam: RF_LOCKDOWN Feature OFF !!!
[   25.468000] RtmpOSFileOpen(): Error 2 opening /etc/Wireless/SingleSKU_5G.dat
[   25.476000] --> Error opening /etc/Wireless/SingleSKU_2G.dat
[   25.480000] MtBfBackOffLoadTable: RF_LOCKDOWN Feature OFF !!!
[   25.488000] RtmpOSFileOpen(): Error 2 opening /etc/Wireless/SingleSKU_BF.dat
[   25.496000] EEPROM Init Done!
[   25.496000] mt_mac_init()-->
[   25.500000] mt_mac_pse_init(2715): Don't Support this now!
[   25.504000] mt7615_init_mac_cr()-->
[   25.508000] mt7615_init_mac_cr(): TMAC_TRCR0=0x82783c8c
[   25.516000] mt7615_init_mac_cr(): TMAC_TRCR1=0x82783c8c
[   25.520000] MtAsicSetMacMaxLen(1288): Not finish Yet!
[   25.524000] <--mt_mac_init()
[   25.532000] CmdRxHdrTransBLUpdateRsp::EventExtCmdResult.u4Status = 0x0
[   25.536000] CmdRxHdrTransBLUpdateRsp::EventExtCmdResult.u4Status = 0x0
[   25.544000] CmdRxHdrTransBLUpdateRsp::EventExtCmdResult.u4Status = 0x0
[   25.552000] MAC Init Done!
[   25.552000] MT7615BBPInit():BBP Initialization.....
[   25.560000]     Band 0: valid=1, isDBDC=0, Band=2, CBW=1, CentCh/PrimCh=1/1, prim_ch_idx=0, txStream=2
[   25.568000]     Band 1: valid=0, isDBDC=0, Band=0, CBW=0, CentCh/PrimCh=0/0, prim_ch_idx=0, txStream=0
[   25.576000] MT7615BBPInit() todo
[   25.580000] PHY Init Done!
[   25.584000] tx_pwr_comp_init():NotSupportYet!
[   25.588000] wdev_attr_update(): wdevId0 = 00:0c:43:26:60:28
[   25.596000] MtCmdSetDbdcCtrlret = 0)
[   25.600000] CountryCode(2.4G/5G)=1/0, RFIC=25, PHY mode(2.4G/5G)=49/49, support 13 channels
[   25.608000] ApAutoChannelAtBootUp----------------->
[   25.612000] ApAutoChannelAtBootUp<-----------------
[   25.616000] Current Channel is 149. DfsZeroWaitSupport=0
[   25.624000] MtAsicSetChBusyStat(840): Not support for HIF_MT yet!
[   25.628000] [PMF]APPMFInit:: apidx=0, MFPC=0, MFPR=0, SHA256=0
[   25.636000] [PMF]WPAMakeRsnIeCap: RSNIE Capability MFPC=0, MFPR=0
[   25.640000] HcUpdatePhyMode(): Update PhyMode for all wdev for this band PhyMode:49,Channel=149
[   25.648000] CountryCode(2.4G/5G)=1/0, RFIC=25, PHY mode(2.4G/5G)=49/49, support 13 channels
[   25.656000] wtc_acquire_groupkey_wcid: Found a non-occupied wtbl_idx:127 for WDEV_TYPE:1
[   25.656000]  LinkToOmacIdx = 0, LinkToWdevType = 1
[   25.688000] bssUpdateBmcMngRate (BSS_INFO_BROADCAST_INFO),                 CmdBssInfoBmcRate.u2BcTransmit= 8192,                 CmdBssInfoBmcRate.u2McTransmit = 8192
[   25.704000] LeadTimeForBcn, OmacIdx = 0, WDEV_WITH_BCN_ABILITY
[   25.808000] [RadarStateCheck]Set into RD_NORMAL_MODE
[   25.824000] MtCmdTxPowerSKUCtrl: fgTxPowerSKUEn = 1
[   25.832000] MtCmdTxPowerPercentCtrl: fgTxPowerPercentEn = 0
[   25.836000] MtCmdTxBfBackoffCtrl: fgTxBFBackoffEn = 0
[   25.840000] mt7615_bbp_adjust():rf_bw=2, ext_ch=1, PrimCh=149, HT-CentCh=151, VHT-CentCh=155
[   25.848000] mt7615_apply_cal_data() : eeprom 0x52 bit 1 is 0, do runtime cal , skip RX reload
[   25.860000] mt7615_apply_cal_data() : eeprom 0x52 bit 0 is 0, do runtime cal , skip TX reload
[   25.868000] MtCmdChannelSwitch: control_chl = 149,control_ch2=0, central_chl = 155 DBDCIdx= 0, Band= 0
[   25.876000] BW = 2,TXStream = 4, RXStream = 4, scan(0)
[   26.968000] :MtCmdPktBudgetCtrl: bssid(255),wcid(65535),type(0)
[   26.980000] ap_phy_rrm_init_byRf(): AP Set CentralFreq at 155(Prim=149, HT-CentCh=151, VHT-CentCh=155, BBP_BW=2)
[   26.992000] [WrapDfsRadarDetectStart]: Band0Ch is 149[WrapDfsRadarDetectStart]: Band1Ch is 0MtAsicSetRalinkBurstMode(2594): Not support for HIF_MT yet!
[   27.004000] MtAsicSetPiggyBack(777): Not support for HIF_MT yet!
[   27.012000] MtAsicSetTxPreamble(2573): Not support for HIF_MT yet!
[   27.016000] RTMPSetLEDStatus: before AndesLedEnhanceOP , status=1, LED_CMD=2!
[   27.024000] AndesLedEnhanceOP: Success!
[   27.028000] Main bssid = 00:0c:43:26:60:28
[   27.032000] AsicRadioOnOffCtrl(): DbdcIdx=0 RadioOn
[   27.036000] MtCmdSetMacTxRxret = 0)
[   27.040000] MCS Set = ff ff ff ff 01
[   27.044000] MtCmdSetMacTxRxret = 0)
[   27.048000] <==== mt_wifi_init, Status=0
[   27.052000] MtCmdEDCCACtrl: BandIdx: 0, EDCCACtrl: 1
[   27.056000] MtCmdEDCCACtrl: BandIdx: 1, EDCCACtrl: 1
[   27.072000] WtcSetMaxStaNum: MaxStaNum:88, BssidNum:4, WdsNum:0, ApcliNum:2, MaxNumChipRept:32, MinMcastWcid:122
[   27.128000] cp_support_is_enabled: set CR4 CP_SUPPORT to Mode 2.
[   27.136000] Generate UUID for apidx(0)
[   27.140000] UUID: c0e33274, len = 16
[   27.140000] 0x0000 : 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
[   27.148000]
[   27.288000] device rai0 entered promiscuous mode
[   27.296000] br-lan: port 4(rai0) entered forwarding state
[   27.300000] br-lan: port 4(rai0) entered forwarding state
[   27.340000] PandoraBox HW NAT v2.52.0 Module Disabled
[   27.396000] PandoraBox HW-NAT v2.52.0 Module Enabled, FoE Size: 16384
[   27.404000] PPE:IPv4 NAT offload for TCP proto default enabled
[   27.408000] PPE:IPv4 NAT offload for UDP proto enabled
[   27.416000] PPE:IPv4 NAT offload for WiFi/ExtIf enabled
[   27.420000] PPE:IPv6 routes offload enabled
[   27.424000] PPE:WAN_ID:2 LAN_ID:1
[   27.464000] DriverOwn()::Return since already in Driver Own...
[   27.476000] SSID[0]=78, EdcaIdx=0
[   27.484000] cfg_mode=9
[   27.484000] cfg_mode=9
[   27.488000] wmode_band_equal(): Band Equal!
[   27.492000] APEdca0
[   27.496000] APEdca1
[   27.496000] APEdca2
[   27.500000] APEdca3
[   27.504000] APSDCapable[0]=0
[   27.508000] APSDCapable[1]=0
[   27.512000] APSDCapable[2]=0
[   27.512000] APSDCapable[3]=0
[   27.516000] APSDCapable[4]=0
[   27.520000] APSDCapable[5]=0
[   27.520000] APSDCapable[6]=0
[   27.524000] APSDCapable[7]=0
[   27.528000] APSDCapable[8]=0
[   27.532000] APSDCapable[9]=0
[   27.532000] APSDCapable[10]=0
[   27.536000] APSDCapable[11]=0
[   27.540000] APSDCapable[12]=0
[   27.540000] APSDCapable[13]=0
[   27.544000] APSDCapable[14]=0
[   27.548000] APSDCapable[15]=0
[   27.552000] default ApCliAPSDCapable[0]=0
[   27.556000] default ApCliAPSDCapable[1]=0
[   27.560000] DfsZeroWait Support=0/0
[   27.564000] DfsZeroWaitCacTime=255/255
[   27.568000] [RTMPSetProfileParameters]Disable DFS/Zero wait=0/0
[   27.596000] [PMF]Set_PMFMFPC_Proc:: apidx=0, Desired MFPC=0
[   27.604000] [PMF]Set_PMFMFPR_Proc:: apidx=0, Desired MFPR=0
[   27.608000] [PMF]Set_PMFSHA256_Proc:: apidx=0, Desired PMFSHA256=0
[   27.628000] HT: Ext Channel = BELOW
[   27.632000] HT: greenap_cap = 0
[   27.668000] WtcSetMaxStaNum: MaxStaNum:88, BssidNum:4, WdsNum:0, ApcliNum:2, MaxNumChipRept:32, MinMcastWcid:122
[   27.680000] Top Init Done!
[   27.684000] Use dev_alloc_skb
[   27.688000] RX[0] DESC a66f4000 size = 8192
[   27.692000] RX[1] DESC a66f6000 size = 8192
[   27.700000] Hif Init Done!
[   27.700000] ctl->txq = c0ceffa0
[   27.704000] ctl->rxq = c0ceffac
[   27.708000] ctl->ackq = c0ceffb8
[   27.712000] ctl->kickq = c0ceffc4
[   27.716000] ctl->tx_doneq = c0ceffd0
[   27.716000] ctl->rx_doneq = c0ceffdc
[   27.724000] mt7615_fw_prepare():FW(8a10), HW(8a10), CHIPID(7615))
[   27.728000] mt7615_fw_prepare(2356): MT7615_E3, USE E3 patch and ram code binary image
[   27.736000] AndesMTLoadRomMethodFwDlRing(1035), cap->rom_patch_len(10206)
[   27.744000] AndesRestartCheck: Current TOP_MISC2(0x1)
[   27.748000] AndesRestartCheck: (TOP_MISC2 = 1), ready to continue...RET(0)
[   27.756000] 20161013140927a
[   27.756000]
[   27.760000] platform =
[   27.760000] ALPS
[   27.764000] hw/sw version =
[   27.768000] 8a108a10
[   27.768000] patch version =
[   27.772000] 00000010
[   27.772000] Patch SEM Status=2
[   27.776000] MtCmdPatchSemGetret = 0)
[   27.780000]
[   27.780000] Patch is not ready && get semaphore success, SemStatus(2)
[   27.788000] EventGenericEventHandler: CMD Success
[   27.792000] MtCmdAddressLenReqret = 0)
[   27.796000] MtCmdPatchFinishReq
[   27.812000] EventGenericEventHandler: CMD Success
[   27.816000] Send checksum req..
[   27.820000] Patch SEM Status=3
[   27.824000] MtCmdPatchSemGetret = 0)
[   27.828000]
[   27.828000] Release patch semaphore, SemStatus(3)
[   27.832000] AndesMTEraseRomPatch
[   27.836000] WfMcuHwInit: Before NICLoadFirmware, check IcapMode=0
[   27.844000] AndesMTLoadFwMethodFwDlRing(809), cap->fw_len(460056)
[   27.848000] Build Date:_201702151653
[   27.852000] Build Date:_201702151653
[   27.856000] AndesRestartCheck: Current TOP_MISC2(0x1)
[   27.860000] AndesRestartCheck: (TOP_MISC2 = 1), ready to continue...RET(0)
[   27.868000] EventGenericEventHandler: CMD Success
[   27.872000] MtCmdAddressLenReqret = 0)
[   27.880000] EventGenericEventHandler: CMD Success
[   27.884000] MtCmdAddressLenReqret = 0)
[   27.888000] MtCmdFwStartReq: override = 1, address = 540672
[   27.896000] EventGenericEventHandler: CMD Success
[   27.900000] Build Date:_201612301011
[   27.904000] EventGenericEventHandler: CMD Success
[   27.908000] MtCmdAddressLenReqret = 0)
[   27.912000] MtCmdFwStartReq: override = 4, address = 0
[   27.984000] EventGenericEventHandler: CMD Success
[   28.024000] WfMcuHwInit: NICLoadFirmware OK, Check IcapMode=0
[   28.028000] MCU Init Done!
[   28.032000] efuse_probe: efuse = 10000212
[   28.036000] RtmpChipOpsEepromHook::e2p_type=2, inf_Type=5
[   28.040000] RtmpEepromGetDefault::e2p_dafault=1
[   28.044000] RtmpChipOpsEepromHook: E2P type(2), E2pAccessMode = 2, E2P default = 1
[   28.052000] NVM is FLASH mode. dev_idx [0] FLASH OFFSET [0x0]
[   28.060000] EEPROM:Read from [Factory] offset 0x0,length 0x400.
[   28.064000] EEPROM:Read from [Factory] offset 0x400,length 0x2400.
[   28.076000] EEPROM:Read from [Factory] offset 0x2600,length 0x2400.
[   28.084000] EEPROM:Read from [Factory] offset 0x4460,length 0x2400.
[   29.304000] br-lan: port 4(rai0) entered forwarding state
[   36.352000] Country Region from e2p = 1
[   36.356000] mt7615_antenna_default_reset(): TxPath = 4, RxPath = 4
[   36.364000] rtmp_read_txpwr_from_eeprom(224): Don't Support this now!
[   36.368000] RTMPReadTxPwrPerRate(1385): Don't Support this now!
[   36.376000] RcRadioInit(): DbdcMode=0, ConcurrentBand=1
[   36.380000] RcRadioInit(): pRadioCtrl=87d1a448,Band=0,rfcap=3,channel=1,PhyMode=2
[   36.388000] MtCmdSetDbdcCtrlret = 0)
[   36.392000] Band Rf: 1, Phy Mode: 2
[   36.396000] AntCfgInit(2616): Not support for HIF_MT yet!
[   36.400000] MtSingleSkuLoadParam: RF_LOCKDOWN Feature OFF !!!
[   36.408000] RtmpOSFileOpen(): Error 2 opening /etc/Wireless/SingleSKU_2G.dat
[   36.412000] --> Error opening /etc/Wireless/SingleSKU_2G.dat
[   36.420000] MtBfBackOffLoadTable: RF_LOCKDOWN Feature OFF !!!
[   36.424000] RtmpOSFileOpen(): Error 2 opening /etc/Wireless/SingleSKU_BF.dat
[   36.432000] EEPROM Init Done!
[   36.436000] mt_mac_init()-->
[   36.436000] mt_mac_pse_init(2715): Don't Support this now!
[   36.444000] mt7615_init_mac_cr()-->
[   36.448000] mt7615_init_mac_cr(): TMAC_TRCR0=0x82783c8c
[   36.452000] mt7615_init_mac_cr(): TMAC_TRCR1=0x82783c8c
[   36.456000] MtAsicSetMacMaxLen(1288): Not finish Yet!
[   36.464000] <--mt_mac_init()
[   36.468000] CmdRxHdrTransBLUpdateRsp::EventExtCmdResult.u4Status = 0x0
[   36.476000] CmdRxHdrTransBLUpdateRsp::EventExtCmdResult.u4Status = 0x0
[   36.484000] CmdRxHdrTransBLUpdateRsp::EventExtCmdResult.u4Status = 0x0
[   36.488000] MAC Init Done!
[   36.492000] MT7615BBPInit():BBP Initialization.....
[   36.496000]     Band 0: valid=1, isDBDC=0, Band=2, CBW=1, CentCh/PrimCh=1/1, prim_ch_idx=0, txStream=2
[   36.504000]     Band 1: valid=0, isDBDC=0, Band=0, CBW=0, CentCh/PrimCh=0/0, prim_ch_idx=0, txStream=0
[   36.516000] MT7615BBPInit() todo
[   36.516000] PHY Init Done!
[   36.524000] tx_pwr_comp_init():NotSupportYet!
[   36.528000] wdev_attr_update(): wdevId0 = 00:0c:43:26:60:78
[   36.532000] MtCmdSetDbdcCtrlret = 0)
[   36.536000] CountryCode(2.4G/5G)=5/7, RFIC=25, PHY mode(2.4G/5G)=14/14, support 14 channels
[   36.544000] ApAutoChannelAtBootUp----------------->
[   36.548000] ApAutoChannelAtBootUp<-----------------
[   36.556000] Current Channel is 8. DfsZeroWaitSupport=0
[   36.560000] MtAsicSetChBusyStat(840): Not support for HIF_MT yet!
[   36.564000] [PMF]APPMFInit:: apidx=0, MFPC=0, MFPR=0, SHA256=0
[   36.572000] [PMF]WPAMakeRsnIeCap: RSNIE Capability MFPC=0, MFPR=0
[   36.576000] HcUpdatePhyMode(): Update PhyMode for all wdev for this band PhyMode:14,Channel=8
[   36.588000] CountryCode(2.4G/5G)=5/7, RFIC=25, PHY mode(2.4G/5G)=14/14, support 14 channels
[   36.596000] wtc_acquire_groupkey_wcid: Found a non-occupied wtbl_idx:127 for WDEV_TYPE:1
[   36.596000]  LinkToOmacIdx = 0, LinkToWdevType = 1
[   36.612000] bssUpdateBmcMngRate (BSS_INFO_BROADCAST_INFO),                 CmdBssInfoBmcRate.u2BcTransmit= 0,                 CmdBssInfoBmcRate.u2McTransmit = 0
[   36.628000] LeadTimeForBcn, OmacIdx = 0, WDEV_WITH_BCN_ABILITY
[   36.736000] [RadarStateCheck]Set into RD_NORMAL_MODE
[   36.756000] MtCmdTxPowerSKUCtrl: fgTxPowerSKUEn = 1
[   36.760000] MtCmdTxPowerPercentCtrl: fgTxPowerPercentEn = 0
[   36.764000] MtCmdTxBfBackoffCtrl: fgTxBFBackoffEn = 0
[   36.772000] mt7615_bbp_adjust():rf_bw=1, ext_ch=3, PrimCh=8, HT-CentCh=6, VHT-CentCh=0
[   36.780000] mt7615_apply_cal_data() : eeprom 0x52 bit 1 is 0, do runtime cal , skip RX reload
[   36.788000] mt7615_apply_cal_data() : eeprom 0x52 bit 0 is 0, do runtime cal , skip TX reload
[   36.796000] MtCmdChannelSwitch: control_chl = 8,control_ch2=0, central_chl = 6 DBDCIdx= 0, Band= 0
[   36.804000] BW = 1,TXStream = 4, RXStream = 4, scan(0)
[   37.332000] ap_phy_rrm_init_byRf(): AP Set CentralFreq at 6(Prim=8, HT-CentCh=6, VHT-CentCh=0, BBP_BW=1)
[   37.340000] [WrapDfsRadarDetectStart]: Band0Ch is 8[WrapDfsRadarDetectStart]: Band1Ch is 0MtAsicSetRalinkBurstMode(2594): Not support for HIF_MT yet!
[   37.352000] MtAsicSetPiggyBack(777): Not support for HIF_MT yet!
[   37.360000] MtAsicSetTxPreamble(2573): Not support for HIF_MT yet!
[   37.368000] RTMPSetLEDStatus: before AndesLedEnhanceOP , status=1, LED_CMD=2!
[   37.372000] AndesLedEnhanceOP: Success!
[   37.376000] Main bssid = 00:0c:43:26:60:78
[   37.380000] AsicRadioOnOffCtrl(): DbdcIdx=0 RadioOn
[   37.388000] MtCmdSetMacTxRxret = 0)
[   37.392000] MCS Set = ff ff ff ff 01
[   37.396000] MtCmdSetMacTxRxret = 0)
[   37.400000] <==== mt_wifi_init, Status=0
[   37.404000] MtCmdEDCCACtrl: BandIdx: 0, EDCCACtrl: 1
[   37.408000] MtCmdEDCCACtrl: BandIdx: 1, EDCCACtrl: 1
[   37.420000] WtcSetMaxStaNum: MaxStaNum:88, BssidNum:4, WdsNum:0, ApcliNum:2, MaxNumChipRept:32, MinMcastWcid:122
[   37.484000] cp_support_is_enabled: set CR4 CP_SUPPORT to Mode 2.
[   37.488000] Generate UUID for apidx(0)
[   37.492000] UUID: c09b3274, len = 16
[   37.496000] 0x0000 : bc 32 9e 00 1d d8 11 b2 86 01 00 0c 43 26 60 78
[   37.504000]
[   37.580000] device ra0 entered promiscuous mode
[   37.588000] br-lan: port 5(ra0) entered forwarding state
[   37.592000] br-lan: port 5(ra0) entered forwarding state
[   37.636000] PandoraBox HW NAT v2.52.0 Module Disabled
[   37.708000] PandoraBox HW-NAT v2.52.0 Module Enabled, FoE Size: 16384
[   37.712000] PPE:IPv4 NAT offload for TCP proto default enabled
[   37.720000] PPE:IPv4 NAT offload for UDP proto enabled
[   37.724000] PPE:IPv4 NAT offload for WiFi/ExtIf enabled
[   37.732000] PPE:IPv6 routes offload enabled
[   37.736000] PPE:WAN_ID:2 LAN_ID:1
[   38.320000] :MtCmdPktBudgetCtrl: bssid(255),wcid(65535),type(0)
[   39.596000] br-lan: port 5(ra0) entered forwarding state
[   80.780000] TxPowerPercentage = 3
[   80.792000] TxPowerPercentage = 3

本帖子中包含更多资源

您需要 登录 才可以下载或查看,没有账号?立即注册

×
我的恩山、我的无线 The best wifi forum is right here.
回复

使用道具 举报

 楼主| 发表于 2017-10-22 21:22 | 显示全部楼层
zhengxinhn 发表于 2017-10-22 20:37
8m真的太抠门了....

暂时够用,关键是没有USB扩展接口情况下,只作为无线路由器、无线AP够用了
我的恩山、我的无线 The best wifi forum is right here.
回复

使用道具 举报

发表于 2017-10-22 21:44 | 显示全部楼层
据说mt7615芯片的频率可以自定义、不知是否可以发射两个5G频率!?、1733+1733=3466!!??

点评

7615只能单工,要么5。8,要么2。4,同时存在是不可能的。  详情 回复 发表于 2018-10-20 21:58
如果按照传统无线电L/C元器件匹配的话,把2.4G频段完全通过软件改换到5.8G,这是不可能的  详情 回复 发表于 2017-10-22 21:46
我的恩山、我的无线 The best wifi forum is right here.
回复

使用道具 举报

 楼主| 发表于 2017-10-22 21:46 | 显示全部楼层
aaaaa89897 发表于 2017-10-22 21:44
据说mt7615芯片的频率可以自定义、不知是否可以发射两个5G频率!?、1733+1733=3466!!??

如果按照传统无线电L/C元器件匹配的话,把2.4G频段完全通过软件改换到5.8G,这是不可能的
我的恩山、我的无线 The best wifi forum is right here.
回复

使用道具 举报

发表于 2017-10-22 21:58 | 显示全部楼层
水星MAC2600R (800 + 1733)
MT7621A
128MB RAM
8 MiB SPI  flash
2G: MT7615N 4x4 (天线:4外置, FEM:无)
5G: MT7615N 4x4 (天线:4外置, FEM:无)
1 WAN 4LAN
USB: 无
我的恩山、我的无线 The best wifi forum is right here.
回复

使用道具 举报

发表于 2017-11-27 22:58 | 显示全部楼层
求教楼主,我的两台mac2600r刷上潘多拉之后,每3-4分钟就会重启,而且mac地址都不正确,原厂固件就没问题,请问大概是怎么造成的?另外求您的编程器固件

点评

能给个刷机教程吗?  详情 回复 发表于 2018-12-5 11:08
我的恩山、我的无线 The best wifi forum is right here.
回复

使用道具 举报

发表于 2018-4-29 08:24 来自手机 | 显示全部楼层
您好,您之前mac2600r的breed和pandorabox固件还在吗?可否发我一份!网上下载不了了!谢谢
我的恩山、我的无线 The best wifi forum is right here.
回复

使用道具 举报

发表于 2018-5-9 18:06 | 显示全部楼层
我也需要你以前的固件啊。
我的恩山、我的无线 The best wifi forum is right here.
回复

使用道具 举报

发表于 2018-5-10 12:31 | 显示全部楼层
怎么这货淘宝上标的是1G内存?7621不是最大512么?
我的恩山、我的无线 The best wifi forum is right here.
回复

使用道具 举报

 楼主| 发表于 2018-6-22 07:49 | 显示全部楼层
统一回复,好久好久没来这里,感谢弟兄们信任,分享编程器固件和Pandora固件
链接:https://pan.baidu.com/s/1BOodZe4JwX5-87TS9A05Mw 密码:rcq1
我的恩山、我的无线 The best wifi forum is right here.
回复

使用道具 举报

发表于 2018-10-20 21:58 | 显示全部楼层
aaaaa89897 发表于 2017-10-22 21:44
据说mt7615芯片的频率可以自定义、不知是否可以发射两个5G频率!?、1733+1733=3466!!??

7615只能单工,要么5。8,要么2。4,同时存在是不可能的。
我的恩山、我的无线 The best wifi forum is right here.
回复

使用道具 举报

您需要登录后才可以回帖 登录 | 立即注册

本版积分规则

有疑问请添加管理员QQ86788181|手机版|小黑屋|Archiver|恩山无线论坛(常州市恩山计算机开发有限公司版权所有) ( 苏ICP备05084872号 )

GMT+8, 2024-4-26 01:32

Powered by Discuz! X3.5

© 2001-2024 Discuz! Team.

| 江苏省互联网有害信息举报中心 举报信箱:js12377 | @jischina.com.cn 举报电话:025-88802724 本站不良内容举报信箱:68610888@qq.com 举报电话:0519-86695797

快速回复 返回顶部 返回列表