找回密码
 立即注册

QQ登录

只需一步,快速开始

搜索
广告投放联系QQ68610888
查看: 101597|回复: 850

【已有改善办法】Nanopi R2S总是过一两天就自己死机了,必须重启

 火... [复制链接]
发表于 2020-5-24 14:12 | 显示全部楼层 |阅读模式
本帖最后由 15416769 于 2020-7-31 08:44 编辑

Nanopi R2S总是过一两天就自己死机了,必须重启。现在刷的是https://github.com/klever1988/nanopi-openwrt/releases 的每日最新固件,是否设置有问题也搞不懂。

1.同样刷klever1988大神的固件的人,是否有同样的问题?是怎么解决的?
2.是否有其他稳定好用的固件推荐?核心诉求只有SS(v贰瑞),DDNS,微信推送,网易云音乐解锁。

基于各位热心网友的回复,做了一些调整之后,R2S已经持续稳定6天了,还有死机情况的朋友可以参考下:
===============================================================
基于各位热心网友的回复,做了一些调整之后,R2S已经持续稳定6天了,还有死机情况的朋友可以参考下
固件:https://github.com/klever1988/nanopi-openwrt
TF卡:老手机用的卡,没特别关注是Class几
电源:从光猫供电换成了华为手机的充电头5V2A
IPV6:彻底关闭,在LAN WAN口设置里面把所有和IPV6有关的选项能禁用的都禁用

===============================================================
贴一个可能的疑点:宽带WAN口的PPPOE隔一段时间就会被踢掉线,可能真的是之前有配置IPV6的情况下时,重拨过程死机。。。。

下面是刚刚WAN口掉线后重拨的日志,很正常:
Sat May 30 20:47:33 2020 daemon.info pppd[28053]: LCP terminated by peer
Sat May 30 20:47:33 2020 daemon.info pppd[28053]: Connect time 2875.1 minutes.
Sat May 30 20:47:33 2020 daemon.info pppd[28053]: Sent 3283348001 bytes, received 1666918510 bytes.
Sat May 30 20:47:33 2020 daemon.notice netifd: Network device 'pppoe-wan' link is down
Sat May 30 20:47:33 2020 daemon.err miniupnpd[4448]: Failed to get IP for interface pppoe-wan
Sat May 30 20:47:33 2020 daemon.warn miniupnpd[4448]: SendNATPMPPublicAddressChangeNotification: cannot get public IP address, stopping
Sat May 30 20:47:33 2020 daemon.notice netifd: Interface 'wan' has lost the connection
Sat May 30 20:47:33 2020 daemon.notice pppd[28053]: Modem hangup
Sat May 30 20:47:33 2020 daemon.notice pppd[28053]: Connection terminated.
Sat May 30 20:47:33 2020 daemon.info pppd[28053]: Sent PADT
Sat May 30 20:47:33 2020 daemon.info pppd[28053]: Exit.
Sat May 30 20:47:33 2020 daemon.notice netifd: Interface 'wan' is now down
Sat May 30 20:47:33 2020 kern.info kernel: [517536.696621] rk_gmac-dwmac ff540000.ethernet eth0: Link is Down
Sat May 30 20:47:33 2020 daemon.notice netifd: Interface 'wan' is disabled
Sat May 30 20:47:33 2020 kern.info kernel: [517536.704321] rk_gmac-dwmac ff540000.ethernet eth0: PHY [stmmac-0:00] driver [RTL8211E Gigabit Ethernet]
Sat May 30 20:47:33 2020 daemon.notice netifd: Interface 'wan' is enabled
Sat May 30 20:47:33 2020 daemon.notice netifd: Interface 'wan' is setting up now
Sat May 30 20:47:33 2020 kern.info kernel: [517536.716590] rk_gmac-dwmac ff540000.ethernet eth0: No Safety Features support found
Sat May 30 20:47:33 2020 kern.warn kernel: [517536.717300] rk_gmac-dwmac ff540000.ethernet eth0: RX IPC Checksum Offload disabled
Sat May 30 20:47:33 2020 kern.warn kernel: [517536.717996] rk_gmac-dwmac ff540000.ethernet eth0: PTP not supported by HW
Sat May 30 20:47:33 2020 kern.info kernel: [517536.718620] rk_gmac-dwmac ff540000.ethernet eth0: configuring for phy/rgmii link mode
Sat May 30 20:47:33 2020 daemon.notice netifd: Network device 'eth0' link is down
Sat May 30 20:47:33 2020 daemon.notice netifd: Interface 'wan' has link connectivity loss
Sat May 30 20:47:33 2020 daemon.notice netifd: Interface 'wan' is now down
Sat May 30 20:47:33 2020 daemon.notice netifd: Interface 'wan' is disabled
Sat May 30 20:47:33 2020 kern.info kernel: [517536.773557] rk_gmac-dwmac ff540000.ethernet eth0: PHY [stmmac-0:00] driver [RTL8211E Gigabit Ethernet]
Sat May 30 20:47:33 2020 kern.info kernel: [517536.784615] rk_gmac-dwmac ff540000.ethernet eth0: No Safety Features support found
Sat May 30 20:47:33 2020 kern.warn kernel: [517536.785330] rk_gmac-dwmac ff540000.ethernet eth0: RX IPC Checksum Offload disabled
Sat May 30 20:47:33 2020 kern.warn kernel: [517536.786027] rk_gmac-dwmac ff540000.ethernet eth0: PTP not supported by HW
Sat May 30 20:47:33 2020 kern.info kernel: [517536.786651] rk_gmac-dwmac ff540000.ethernet eth0: configuring for phy/rgmii link mode
Sat May 30 20:47:33 2020 daemon.notice netifd: Interface 'wan' is enabled
Sat May 30 20:47:34 2020 user.notice ddns-scripts[31156]: myddns_ipv4: PID '31156' terminated by 'SIGTERM' at 2020-05-30 20:47
Sat May 30 20:47:38 2020 daemon.notice netifd: Network device 'eth0' link is up
Sat May 30 20:47:38 2020 daemon.notice netifd: Interface 'wan' has link connectivity
Sat May 30 20:47:38 2020 daemon.notice netifd: Interface 'wan' is setting up now
Sat May 30 20:47:38 2020 kern.info kernel: [517541.892973] rk_gmac-dwmac ff540000.ethernet eth0: Link is Up - 1Gbps/Full - flow control rx/tx
Sat May 30 20:47:38 2020 daemon.err insmod: module is already loaded - pppox
Sat May 30 20:47:39 2020 daemon.err insmod: module is already loaded - pppoe
Sat May 30 20:47:39 2020 daemon.notice netifd: wan (3011): uci: Entry not found
Sat May 30 20:47:39 2020 daemon.info pppd[3051]: Plugin rp-pppoe.so loaded.
Sat May 30 20:47:39 2020 daemon.info pppd[3051]: RP-PPPoE plugin version 3.8p compiled against pppd 2.4.8
Sat May 30 20:47:39 2020 daemon.notice pppd[3051]: pppd 2.4.8 started by root, uid 0
Sat May 30 20:47:44 2020 daemon.info pppd[3051]: PPP session is 52993
Sat May 30 20:47:44 2020 daemon.warn pppd[3051]: Connected to 70:62:0e:1c:ff:30 via interface eth0
Sat May 30 20:47:44 2020 kern.info kernel: [517547.100229] pppoe-wan: renamed from ppp0
Sat May 30 20:47:44 2020 daemon.info pppd[3051]: Renamed interface ppp0 to pppoe-wan
Sat May 30 20:47:44 2020 daemon.info pppd[3051]: Using interface pppoe-wan
Sat May 30 20:47:44 2020 daemon.notice pppd[3051]: Connect: pppoe-wan <--> eth0
Sat May 30 20:47:44 2020 daemon.info pppd[3051]: syncppp not active
Sat May 30 20:47:44 2020 daemon.info pppd[3051]: Remote message: Authentication Successful,Welcome!
Sat May 30 20:47:44 2020 daemon.notice pppd[3051]: PAP authentication succeeded
Sat May 30 20:47:44 2020 daemon.notice pppd[3051]: peer from calling number * authorized
Sat May 30 20:47:44 2020 daemon.err miniupnpd[4448]: Failed to get IP for interface pppoe-wan
Sat May 30 20:47:44 2020 daemon.warn miniupnpd[4448]: SendNATPMPPublicAddressChangeNotification: cannot get public IP address, stopping
Sat May 30 20:47:44 2020 daemon.err miniupnpd[4448]: Failed to get IP for interface pppoe-wan
Sat May 30 20:47:44 2020 daemon.warn miniupnpd[4448]: SendNATPMPPublicAddressChangeNotification: cannot get public IP address, stopping
Sat May 30 20:47:44 2020 daemon.notice pppd[3051]: local  IP address 61.***.***.**
Sat May 30 20:47:44 2020 daemon.notice pppd[3051]: remote IP address 61.***.***.*
Sat May 30 20:47:44 2020 daemon.notice pppd[3051]: primary   DNS address 202.**.***.**
Sat May 30 20:47:44 2020 daemon.notice pppd[3051]: secondary DNS address 202.**.***.**


本帖子中包含更多资源

您需要 登录 才可以下载或查看,没有账号?立即注册

×

点评

r2s也是一老死机,做主路由可能还是不太行,可能是跟固件有关系,而且有ipv6需求做主路由还不能关掉  发表于 2024-4-18 19:36
这个小东西问题太多,没大神更近固件,也不知道是哪里的问题,我已经准备出了,还是换回软路由j1900  发表于 2020-6-24 05:59

评分

参与人数 1恩山币 +2 收起 理由
todayfff + 2 已经按照帖子成功运行9d 21h 0m 49s

查看全部评分

我的恩山、我的无线 The best wifi forum is right here.
发表于 2020-5-24 14:16 | 显示全部楼层
检查tf卡

点评

怎么检查?老哥?有什么标准或者有什么要求?  详情 回复 发表于 2020-5-24 14:17
我的恩山、我的无线 The best wifi forum is right here.
回复

使用道具 举报

 楼主| 发表于 2020-5-24 14:17 | 显示全部楼层

怎么检查?老哥?有什么标准或者有什么要求?

点评

tf卡一定要圈10以上的,越高速越好不然会有各种问题出现!!!!  详情 回复 发表于 2020-5-25 20:20
我的恩山、我的无线 The best wifi forum is right here.
回复

使用道具 举报

发表于 2020-5-24 14:25 | 显示全部楼层
我x86遇到过一些玄学的问题,无缘无故死机,无响应,等待时间级长。最后发现固态硬盘使用时间长加上老硬盘主控没有均匀磨损技术,导致一些区块速度只有几十kb,其他区块80多m,后来换了个硬盘就好了。你写入系统的时候注意一下会不会有突然的掉速情况

点评

所以我首先怀疑是内存卡质量差的问题  详情 回复 发表于 2020-9-30 01:32
我的恩山、我的无线 The best wifi forum is right here.
回复

使用道具 举报

发表于 2020-5-24 14:27 | 显示全部楼层
做一下全盘写入,全盘读取
我的恩山、我的无线 The best wifi forum is right here.
回复

使用道具 举报

发表于 2020-5-24 14:53 | 显示全部楼层
我也是一样的状况  等待新的固件吧  
我用的是铝壳    应该不是温度导致的
看看有没有大神出好的固件
我的恩山、我的无线 The best wifi forum is right here.
回复

使用道具 举报

发表于 2020-5-24 15:04 | 显示全部楼层
电源稳么?
我的恩山、我的无线 The best wifi forum is right here.
回复

使用道具 举报

 楼主| 发表于 2020-5-24 15:40 | 显示全部楼层
这玩意还是太小众了,遇到问题无处查不说,固件也没几个,官方的固件也不说合入openwrt的官方一起维护。考虑还是便宜出了算了
我的恩山、我的无线 The best wifi forum is right here.
回复

使用道具 举报

发表于 2020-5-24 20:02 | 显示全部楼层
klever1988的固件在我这里还是挺稳得
建议检查电源,我目前用的是2A的电源

如果想换固件可以试试下面两个
https://github.com/songchenwen/nanopi-r2s
https://github.com/QiuSimons/R2S-OpenWrt

点评

请问这个网址怎么下载固件  详情 回复 发表于 2021-2-1 21:45
你现在用哪个固件?  详情 回复 发表于 2020-6-16 14:38
你是做主路由用吗?一直不重启连续工作多日也很稳定是吗?是不是那个mini的版本?  详情 回复 发表于 2020-5-24 20:59
我的恩山、我的无线 The best wifi forum is right here.
回复

使用道具 举报

 楼主| 发表于 2020-5-24 20:59 来自手机 | 显示全部楼层
kingrose 发表于 2020-5-24 20:02
klever1988的固件在我这里还是挺稳得
建议检查电源,我目前用的是2A的电源


你是做主路由用吗?一直不重启连续工作多日也很稳定是吗?是不是那个mini的版本?
我的恩山、我的无线 The best wifi forum is right here.
回复

使用道具 举报

发表于 2020-5-24 21:23 | 显示全部楼层
表示也是用的minimal版,半个月都不用重启一次,我是当主路由用的 ,只开了低调上网

点评

能分享下固件吗  详情 回复 发表于 2021-2-1 21:46
老哥,是哪天的版本?  详情 回复 发表于 2020-5-24 21:31
我的恩山、我的无线 The best wifi forum is right here.
回复

使用道具 举报

 楼主| 发表于 2020-5-24 21:31 来自手机 | 显示全部楼层
y456123 发表于 2020-5-24 21:23
表示也是用的minimal版,半个月都不用重启一次,我是当主路由用的 ,只开了低调上网

老哥,是哪天的版本?
我的恩山、我的无线 The best wifi forum is right here.
回复

使用道具 举报

发表于 2020-5-24 22:25 | 显示全部楼层
我的也出现死机的问题了,总是要重启,不知道是不是固件是问题
我的恩山、我的无线 The best wifi forum is right here.
回复

使用道具 举报

发表于 2020-5-24 22:48 | 显示全部楼层
换个卡试试。现在用minimal很稳定。不考虑噪音的话散热用风扇要比铝合金壳子强。
我的恩山、我的无线 The best wifi forum is right here.
回复

使用道具 举报

 楼主| 发表于 2020-5-24 23:29 来自手机 | 显示全部楼层
先把电源从光猫的usb转成老手机的5v2a电源了,不行再换个tf卡看看
我的恩山、我的无线 The best wifi forum is right here.
回复

使用道具 举报

您需要登录后才可以回帖 登录 | 立即注册

本版积分规则

有疑问请添加管理员QQ86788181|手机版|小黑屋|Archiver|恩山无线论坛(常州市恩山计算机开发有限公司版权所有) ( 苏ICP备05084872号 )

GMT+8, 2024-4-20 05:41

Powered by Discuz! X3.5

© 2001-2024 Discuz! Team.

| 江苏省互联网有害信息举报中心 举报信箱:js12377 | @jischina.com.cn 举报电话:025-88802724 本站不良内容举报信箱:68610888@qq.com 举报电话:0519-86695797

快速回复 返回顶部 返回列表