|
|
U-Boot 1.1.4-ga354b4f2-dirty (Jun 26 2015 - 11:27:49)
ap143 - Honey Bee 1.0DRAM:
sri
Honey Bee 1.0
ath_ddr_initial_config(198): (16bit) ddr2 init
tap = 0x00000003
Tap (low, high) = (0x8, 0x32)
Tap values = (0x1d, 0x1d, 0x1d, 0x1d)
64 MB
Top of RAM usable for U-Boot at: 84000000
Reserving 198k for U-Boot at: 83fcc000
Reserving 192k for malloc() at: 83f9c000
Reserving 44 Bytes for Board Info at: 83f9bfd4
Reserving 36 Bytes for Global Data at: 83f9bfb0
Reserving 128k for boot params() at: 83f7bfb0
Stack Pointer at: 83f7bf98
Now running in RAM - U-Boot at: 83fcc000
Flash Manuf Id 0xc2, DeviceId0 0x20, DeviceId1 0x17
flash size 8MB, sector count = 128
Flash: 8 MB
*** Warning - bad CRC, using default environment
*** Warning *** : PCIe WLAN Module not found !!!
In: serial
Out: serial
Err: serial
Net: ath_gmac_enet_initialize...
No valid address in Flash. Using fixed address
No valid address in Flash. Using fixed address
ath_gmac_enet_initialize: reset mask:c02200
Scorpion ---->S27 PHY*
S27 reg init
: cfg1 0x800c0000 cfg2 0x7114
eth0: 00:03:7f:09:0b:ad
athrs27_phy_setup ATHR_PHY_CONTROL 4 :1000
athrs27_phy_setup ATHR_PHY_SPEC_STAUS 4 :10
eth0 up
Honey Bee ----> MAC 1 S27 PHY *
S27 reg init
ATHRS27: resetting s27
ATHRS27: s27 reset done
: cfg1 0x800c0000 cfg2 0x7214
eth1: 00:03:7f:09:0b:ad
athrs27_phy_setup ATHR_PHY_CONTROL 0 :1000
athrs27_phy_setup ATHR_PHY_SPEC_STAUS 0 :10
athrs27_phy_setup ATHR_PHY_CONTROL 1 :1000
athrs27_phy_setup ATHR_PHY_SPEC_STAUS 1 :50
athrs27_phy_setup ATHR_PHY_CONTROL 2 :1000
athrs27_phy_setup ATHR_PHY_SPEC_STAUS 2 :10
athrs27_phy_setup ATHR_PHY_CONTROL 3 :1000
athrs27_phy_setup ATHR_PHY_SPEC_STAUS 3 :10
eth1 up
eth0, eth1
Setting 0x181162c0 to 0x50a1a100
Hit any key to stop autoboot: 0
## Booting image at 9f050000 ...
Image Name: MIPS OpenWrt Linux-3.18.36
Created: 2016-11-28 14:41:05 UTC
Image Type: MIPS Linux Kernel Image (lzma compressed)
Data Size: 1161283 Bytes = 1.1 MB
Load Address: 80060000
Entry Point: 80060000
Verifying Checksum at 0x9f050040 ...OK
Uncompressing Kernel Image ... OK
No initrd
## Transferring control to Linux (at address 80060000) ...
## Giving linux memsize in bytes, 67108864
Starting kernel ...
[ 0.000000] Linux version 3.18.36 (luq@luq-nuc) (gcc version 4.8.3 (OpenWrt/L
inaro GCC 4.8-2014.04 r49404) ) #2 Mon Nov 28 22:40:30 CST 2016
[ 0.000000] bootconsole [early0] enabled
[ 0.000000] CPU0 revision is: 00019374 (MIPS 24Kc)
[ 0.000000] SoC: Qualcomm Atheros QCA9533 ver 2 rev 0
[ 0.000000] Determined physical RAM map:
[ 0.000000] memory: 04000000 @ 00000000 (usable)
[ 0.000000] Initrd not found or empty - disabling initrd
[ 0.000000] Zone ranges:
[ 0.000000] Normal [mem 0x00000000-0x03ffffff]
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x00000000-0x03ffffff]
[ 0.000000] Initmem setup node 0 [mem 0x00000000-0x03ffffff]
[ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
[ 0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32
bytes
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pag
es: 16256
[ 0.000000] Kernel command line: board=ALFA-WAPN32 console=ttyS0,115200 mtdp
arts=spi0.0:256k(u-boot)ro,64k(u-boot-env)ro,1536k(kernel),6272k(rootfs),64k(cal
data),7808k@0x50000(firmware) rootfstype=squashfs,jffs2 noinitrd
[ 0.000000] PID hash table entries: 256 (order: -2, 1024 bytes)
[ 0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
[ 0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.000000] Writing ErrCtl register=00000000
[ 0.000000] Readback ErrCtl register=00000000
[ 0.000000] Memory: 60880K/65536K available (2537K kernel code, 132K rwdata,
536K rodata, 240K init, 189K bss, 4656K reserved)
[ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[ 0.000000] NR_IRQS:51
[ 0.000000] Clocks: CPU:550.000MHz, DDR:400.000MHz, AHB:200.000MHz, Ref:25.00
0MHz
[ 0.000000] Calibrating delay loop... 366.18 BogoMIPS (lpj=1830912)
[ 0.060000] pid_max: default: 32768 minimum: 301
[ 0.060000] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.070000] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.080000] NET: Registered protocol family 16
[ 0.080000] MIPS: machine is ALFA Network WAPN32
[ 0.540000] Switched to clocksource MIPS
[ 0.550000] NET: Registered protocol family 2
[ 0.550000] TCP established hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.550000] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.560000] TCP: Hash tables configured (established 1024 bind 1024)
[ 0.570000] TCP: reno registered
[ 0.570000] UDP hash table entries: 256 (order: 0, 4096 bytes)
[ 0.580000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[ 0.580000] NET: Registered protocol family 1
[ 0.590000] futex hash table entries: 256 (order: -1, 3072 bytes)
[ 0.610000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.610000] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORIT
Y) (c) 2001-2006 Red Hat, Inc.
[ 0.620000] msgmni has been set to 118
[ 0.630000] io scheduler noop registered
[ 0.630000] io scheduler deadline registered (default)
[ 0.640000] Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled
[ 0.640000] console [ttyS0] disabled
[ 0.670000] serial8250.0: ttyS0 at MMIO 0x18020000 (irq = 11, base_baud = 156
2500) is a 16550A
[ 0.680000] console [ttyS0] enabled
[ 0.680000] console [ttyS0] enabled
[ 0.680000] bootconsole [early0] disabled
[ 0.680000] bootconsole [early0] disabled
[ 0.700000] m25p80 spi0.0: found mx25l6405d, expected m25p80
[ 0.700000] m25p80 spi0.0: mx25l6405d (8192 Kbytes)
[ 0.710000] 6 cmdlinepart partitions found on MTD device spi0.0
[ 0.710000] Creating 6 MTD partitions on "spi0.0":
[ 0.720000] 0x000000000000-0x000000040000 : "u-boot"
[ 0.720000] 0x000000040000-0x000000050000 : "u-boot-env"
[ 0.730000] 0x000000050000-0x0000001d0000 : "kernel"
[ 0.740000] 0x0000001d0000-0x0000007f0000 : "rootfs"
[ 0.740000] mtd: device 3 (rootfs) set to be root filesystem
[ 0.750000] 1 squashfs-split partitions found on MTD device rootfs
[ 0.760000] 0x0000005f0000-0x0000007f0000 : "rootfs_data"
[ 0.760000] 0x0000007f0000-0x000000800000 : "caldata"
[ 0.770000] 0x000000050000-0x0000007f0000 : "firmware"
[ 0.810000] libphy: ag71xx_mdio: probed
[ 1.400000] ag71xx-mdio.1: Found an AR934X built-in switch
[ 1.440000] eth0: Atheros AG71xx at 0xba000000, irq 5, mode:GMII
[ 2.040000] ag71xx ag71xx.0: connected to PHY at ag71xx-mdio.1:04 [uid=004dd0
42, driver=Generic PHY]
[ 2.050000] eth1: Atheros AG71xx at 0xb9000000, irq 4, mode:MII
[ 2.060000] TCP: cubic registered
[ 2.060000] NET: Registered protocol family 17
[ 2.060000] bridge: automatic filtering via arp/ip/ip6tables has been depreca
ted. Update your scripts to load br_netfilter if you need this.
[ 2.080000] 8021q: 802.1Q VLAN Support v1.8
[ 2.090000] VFS: Mounted root (squashfs filesystem) readonly on device 31:3.
[ 2.100000] Freeing unused kernel memory: 240K (80384000 - 803c0000)
[ 3.390000] init: Console is alive
[ 3.390000] init: - watchdog -
[ 5.170000] usbcore: registered new interface driver usbfs
[ 5.170000] usbcore: registered new interface driver hub
[ 5.180000] usbcore: registered new device driver usb
[ 5.190000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 5.200000] ehci-platform: EHCI generic platform driver
[ 5.200000] ehci-platform ehci-platform: EHCI Host Controller
[ 5.210000] ehci-platform ehci-platform: new USB bus registered, assigned bus
number 1
[ 5.220000] ehci-platform ehci-platform: irq 3, io mem 0x1b000000
[ 5.240000] ehci-platform ehci-platform: USB 2.0 started, EHCI 1.00
[ 5.240000] hub 1-0:1.0: USB hub found
[ 5.250000] hub 1-0:1.0: 1 port detected
[ 5.400000] init: - preinit -
[ 5.960000] random: mktemp urandom read with 9 bits of entropy available
Press the [f] key and hit [enter] to enter failsafe mode
Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level
[ 7.510000] eth0: link up (1000Mbps/Full duplex)
[ 9.300000] jffs2: notice: (318) jffs2_build_xattr_subsystem: complete buildi
ng xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0
orphan) found.
[ 9.310000] mount_root: overlay filesystem has not been fully initialized yet
[ 9.330000] mount_root: switching to jffs2 overlay
[ 9.640000] eth0: link down
[ 9.650000] procd: - early -
[ 9.650000] procd: - watchdog -
[ 10.580000] procd: - ubus -
[ 11.590000] procd: - init -
Please press Enter to activate this console.
[ 12.890000] NET: Registered protocol family 10
[ 12.910000] Initializing XFRM netlink socket
[ 12.910000] NET: Registered protocol family 15
[ 12.950000] ip6_tables: (C) 2000-2006 Netfilter Core Team
[ 12.970000] Loading modules backported from Linux version v4.4-rc5-1913-gc8fd
f68
[ 12.980000] Backport generated by backports.git backports-20151218-0-g2f58d9d
[ 12.990000] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 13.010000] nf_conntrack version 0.5.0 (955 buckets, 3820 max)
[ 13.050000] usbcore: registered new interface driver usbserial
[ 13.050000] usbcore: registered new interface driver usbserial_generic
[ 13.060000] usbserial: USB Serial support registered for generic
[ 13.090000] xt_time: kernel timezone is -0000
[ 13.210000] PPP generic driver version 2.4.2
[ 13.220000] NET: Registered protocol family 24
[ 13.280000] usbcore: registered new interface driver option
[ 13.290000] usbserial: USB Serial support registered for GSM modem (1-port)
[ 13.310000] usbcore: registered new interface driver rt2800usb
[ 13.340000] ath9k: ath9k patched 2016-08-18
[ 13.360000] ieee80211 phy0: Atheros AR9531 Rev:2 mem=0xb8100000, irq=47
[ 32.380000] device eth0 entered promiscuous mode
[ 32.380000] IPv6: ADDRCONF(NETDEV_UP): br-lan: link is not ready
[ 32.480000] IPv6: ADDRCONF(NETDEV_UP): eth1: link is not ready
[ 34.040000] eth0: link up (1000Mbps/Full duplex)
[ 34.040000] br-lan: port 1(eth0) entered forwarding state
[ 34.050000] br-lan: port 1(eth0) entered forwarding state
[ 34.070000] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
[ 35.230000] eth1: link up (100Mbps/Full duplex)
[ 35.230000] IPv6: ADDRCONF(NETDEV_CHANGE): eth1: link becomes ready
[ 36.050000] br-lan: port 1(eth0) entered forwarding state
[ 37.910000] lp_rxdp freezed:0
[ 37.910000] HW RX hang detected, schedule chip reset
[ 38.910000] lp_rxdp freezed:0
[ 38.910000] HW RX hang detected, schedule chip reset
[ 39.430000] lp_rxdp freezed:0
[ 39.430000] HW RX hang detected, schedule chip reset
[ 40.430000] lp_rxdp freezed:0
[ 40.430000] HW RX hang detected, schedule chip reset
[ 41.430000] lp_rxdp freezed:0
[ 41.430000] HW RX hang detected, schedule chip reset
[ 42.430000] lp_rxdp freezed:0
[ 42.430000] HW RX hang detected, schedule chip reset
[ 43.430000] lp_rxdp freezed:0
[ 43.430000] HW RX hang detected, schedule chip reset
[ 43.570000] device wlan0 entered promiscuous mode
[ 66.880000] random: nonblocking pool is initialized
[ 83.430000] lp_rxdp freezed:0
[ 83.430000] HW RX hang detected, schedule chip reset
[ 98.430000] lp_rxdp freezed:0
[ 98.430000] HW RX hang detected, schedule chip reset
[ 114.430000] lp_rxdp freezed:0
[ 114.430000] HW RX hang detected, schedule chip reset
[ 129.430000] lp_rxdp freezed:0
[ 129.430000] HW RX hang detected, schedule chip reset
[ 150.430000] lp_rxdp freezed:0
[ 150.430000] HW RX hang detected, schedule chip reset
[ 154.430000] lp_rxdp freezed:0
[ 154.430000] HW RX hang detected, schedule chip reset
[ 166.430000] lp_rxdp freezed:0
[ 166.430000] HW RX hang detected, schedule chip reset
[ 187.430000] lp_rxdp freezed:0
[ 187.430000] HW RX hang detected, schedule chip reset
[ 191.430000] lp_rxdp freezed:0
[ 191.430000] HW RX hang detected, schedule chip reset
[ 206.430000] lp_rxdp freezed:0
[ 206.430000] HW RX hang detected, schedule chip reset
[ 218.430000] lp_rxdp freezed:0
[ 218.430000] HW RX hang detected, schedule chip reset
[ 233.430000] lp_rxdp freezed:0
[ 233.430000] HW RX hang detected, schedule chip reset
[ 254.430000] lp_rxdp freezed:0
[ 254.430000] HW RX hang detected, schedule chip reset
[ 258.440000] lp_rxdp freezed:0
[ 258.440000] HW RX hang detected, schedule chip reset
[ 279.440000] lp_rxdp freezed:0
[ 279.440000] HW RX hang detected, schedule chip reset |
|
简体中文
繁體中文
English
日本語
Deutsch
한국 사람
بالعربية
TÜRKÇE
português
คนไทย
IP卡
狗仔卡
发表于 2019-4-13 17:08
置顶卡
沉默卡
喧嚣卡
顶贴卡
显身卡