我的恩山,帮帮我吧!
我现在想修改NEC WL5400AP的国家标准,我发现有一台5400设备已被人修改成美国标准了,不知道为什么set country没有反应,高手请帮我看看下列哪个命令是修改频率的????AP login: admin
Password:
Atheros Access Point Rev 3.0.1.5
wlan1 -> get power
TransmitPower: full
Current Transmit Output Power 18.0 dBm
wlan1 -> set country
Invalid parameter: country
Type "help" for a list of valid commands.
wlan1 -> set
set 11gonly disable -- Disable 11g only allowed
set 11gonly enable -- Enable 11g only allowed
set 11goptimize -- Set 11g Optimization Level
set 11goverlapbss disable -- Disable Overlapping BSS protection
set 11goverlapbss enable -- Enable Overlapping BSS protection
set abolt --
set acl allow -- Add MAC address to the ACL
set acl enable -- Select Restricted Access
set acl deny -- Add MAC address to the disabled ACL
set acl disable -- Select Unrestrict Access
set acl keymap -- Add Encryption key mapping for MAC addres
s
set acl strict -- Select Restricted (w/ACL match) Access
set aging -- Set Aging Interval
set antenna best -- Enable antenna diversity
set antenna 1 -- Select antenna 1
set antenna 2 -- Select antenna 2
set authentication open-system -- Select Open-System Authentication Type
set authentication shared-key -- Select Shared-Key Authentication Type
set authentication auto -- Select auto Authentication Type
set authentication WPA -- Select Authentication WPA Type
set authentication WPA-PSK -- Select Authentication WPA-PSK Type
set autochannelselect disable -- Disable Automatic Channel Selection
set autochannelselect enable -- Enable Automatic Channel Selection
set beaconinterval -- Modify Beacon Interval
set burstSeqThreshold -- Set Max Number of frames in a Burst
set burstTime -- Set Burst Time
set channel -- Set Radio Channel
set cipher wep -- Select wep
set cipher aes -- Select aes
set cipher tkip -- Select tkip
set cipher auto -- Select cipher through negotiation
set ctsmode -- Set CTS Mode
set ctsrate -- Set CTS Rate
set ctstype -- Set CTS Type
set domainsuffix -- Set Domain Name Server Suffix
set dtim -- Set Data Beacon Rate (DTIM)
set encryption disable -- Disable Encryption
set encryption enable -- Enable Encryption
set extendedchanmode disable -- Disable Extended Channel Mode
set extendedchanmode enable -- Enable Extended Channel Mode
set factorydefault -- Restore to Default Factory Settings
set fragmentthreshold -- Set Fragment Threshold
set frequency -- Set Radio Frequency (MHz)
set gateway -- Set Gateway IP Address
set groupkeyupdate -- Set Group Key Update Interval (in Seconds
)
set hostipaddr -- Set Host IP address
set ipaddr -- Set IP Address
set ipconfig dhcp -- get ip from dhcp
set ipconfig Manual -- get ip by manual
set ipmask -- Set IP Subnet Mask
set key default -- Set Default Encryption Key
set key 40 -- Set 40-bit Encryption Key
set key 104 -- Set 104-bit Encryption Key
set key 128 -- Set 128-bit Encryption Key
set keyentrymethod hexadecimal -- Key contains (0 - 9, A - F)
set keyentrymethod asciitext -- Key contains keyboard characters
set keysource flash -- All keys will be read from flash (no key
derivation)
set keysource server -- All keys will be derived from authenticat
ion server
set keysource mixed -- Keys read from flash or derived from auth
entication server
set login -- Modify Login User Name
set mac -- Set Ethernet & Wireless Mac
set maxstation -- Set Max STA number
set nameaddress -- Set Name Server IP address
set operationMode ap -- Operating as Access Point
set operationMode sta -- Operating as Wireless Client
set operationMode ppt -- Operating as Wireless Bridge
set operationMode mpt -- Operating as Multi-point Bridge
set operationMode repeater -- Operating as Wireless Repeater
set password -- Modify Password
set passphrase -- Modify Passphrase
set power full -- Set maximum (normal) transmit power
set power half -- Set fractional (1/2) transmit power
set power quarter -- Set fractional (1/4) transmit power
set power eighth -- Set fractional (1/8) transmit power
set power min -- Set minimum transmit power
set radiusname -- Set RADIUS name or IP address
set radiusport -- Set RADIUS port number
set radiussecret -- Set RADIUS shared secret
set rate best -- Select best data rate
set rate 1 -- Select 1 Mbps
set rate 2 -- Select 2 Mbps
set rate 5.5 -- Select 5.5 Mbps
set rate 11 -- Select 11 Mbps
set rate 6 -- Select 6 Mbps
set rate 9 -- Select 9 Mbps
set rate 12 -- Select 12 Mbps
set rate 18 -- Select 18 Mbps
set rate 24 -- Select 24 Mbps
set rate 36 -- Select 36 Mbps
set rate 48 -- Select 48 Mbps
set rate 54 -- Select 54 Mbps
set remoteAP -- Set Remote AP's Mac Address
set rtsthreshold -- Set RTS/CTS Threshold
set shortpreamble disable -- Disable Short Preamble (use only long)
set shortpreamble enable -- Enable Short and Long Preamble
set shortslottime disable -- Disable Short Slot Time (use only long)
set shortslottime enable -- Enable Short Slot Time
set sntpserver -- Set SNTP/NTP Server IP Address
set ssid -- Set Service Set ID
set ssidsuppress enable -- Enable SSID suppress mode
set ssidsuppress disable -- Disable SSID suppress mode
set SuperG enable -- Enable SuperG Features
set SuperG disable -- Disable SuperG Features
set systemname -- Set Access Point System Name
set telnet disable -- Disable Telnet access
set telnet enable -- Enable Telnet access
set timeout -- Set Telnet Timeout
set tzone -- Set Time Zone Setting
set wlanstate disable -- Disable wlan
set wlanstate enable -- Enable wlan
set wirelessmode 11a -- 802.11a
set wirelessmode 11b -- 802.11b
set wirelessmode 11g -- 802.11g
set wirelessmode 108g -- 802.11g Turbo
set wirelessmode turbo -- 802.11a Turbo
Not enough parameters!
wlan1 -> set factorydefault
页:
[1]