NAP840+编程器固件
本帖最后由 PerNet 于 2022-8-6 16:45 编辑固件下载地址： https://2018-1251233090.cos.ap-s ... %98%E8%AE%A4MAC.zip
瑞昱（Realtek）RTL8196D+8192ER 方案，知道的有360P1同款
收了几个anp840+用磊科286管理AP挺不错，有一个发现固件坏了。直接备份好的编程器固件写入正常使用，用winhex搜mac地址修改后自动重置为081011000304，记录一下，有需要的可以下载研究，希望有大佬解惑。
下面是修改mac后启动报错的ttl输出，第一次开机发现有个error报错然后自动重启，mac就变081011000304了，报错代码：
[*]ERROR: Invalid checksum of current setting! for HW from /dev/mtdblock2, offset:6, len:5522,
[*]
发现好像和factory_args.sh 这个有关，用binwalk 解压后看不懂，已上传有兴趣的可以研究研究。
MAC在007c001f处修改。经过几次测试发现只要是修改007c0000到007c1597 这一部分任意数据，用编程器刷回就会报错mac地址变默认。
Booting...
@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@
@
@ chip__no chip__id mfr___id dev___id cap___id size_sft dev_size chipSize
@ 0000000h 0ef4017h 00000efh 0000040h 0000017h 0000000h 0000017h 0800000h
@ blk_size blk__cnt sec_size sec__cnt pageSize page_cnt chip_clk chipName
@ 0010000h 0000080h 0001000h 0000800h 0000100h 0000010h 000003eh W25Q64
@
@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@
---RealTek(RTL8196D)at 2018.04.03-10:30+0800 v1.6b (579MHz)
====no sys signature at 00010000!cs6c
ret=0sys signature at 00010000!
====no sys signature at 00020000!cs6c
ret=0sys signature at 00020000!
ret=2sys signature at 00030000!
checksum sum 0, p_kernel_img 80500000, 00117882
no rootfs signature at 000E0000!
no rootfs signature at 000F0000!
no rootfs signature at 00130000!
no rootfs signature at 000E1000!
no rootfs signature at 000E2000!
no rootfs signature at 000E3000!
no rootfs signature at 000E4000!
no rootfs signature at 000E5000!
no rootfs signature at 000E6000!
no rootfs signature at 000E7000!
no rootfs signature at 000E8000!
no rootfs signature at 000E9000!
no rootfs signature at 000EA000!
no rootfs signature at 000EB000!
no rootfs signature at 000EC000!
no rootfs signature at 000ED000!
no rootfs signature at 000EE000!
no rootfs signature at 000EF000!
no rootfs signature at 000F1000!
no rootfs signature at 000F2000!
no rootfs signature at 000F3000!
no rootfs signature at 000F4000!
no rootfs signature at 000F5000!
no rootfs signature at 000F6000!
no rootfs signature at 000F7000!
no rootfs signature at 000F8000!
no rootfs signature at 000F9000!
no rootfs signature at 000FA000!
no rootfs signature at 000FB000!
no rootfs signature at 000FC000!
no rootfs signature at 000FD000!
no rootfs signature at 000FE000!
no rootfs signature at 000FF000!
no rootfs signature at 00100000!
no rootfs signature at 00101000!
no rootfs signature at 00102000!
no rootfs signature at 00103000!
no rootfs signature at 00104000!
no rootfs signature at 00105000!
no rootfs signature at 00106000!
no rootfs signature at 00107000!
no rootfs signature at 00108000!
no rootfs signature at 00109000!
no rootfs signature at 0010A000!
no rootfs signature at 0010B000!
no rootfs signature at 0010C000!
no rootfs signature at 0010D000!
no rootfs signature at 0010E000!
no rootfs signature at 0010F000!
no rootfs signature at 00110000!
no rootfs signature at 00111000!
no rootfs signature at 00112000!
no rootfs signature at 00113000!
no rootfs signature at 00114000!
no rootfs signature at 00115000!
no rootfs signature at 00116000!
no rootfs signature at 00117000!
no rootfs signature at 00118000!
no rootfs signature at 00119000!
no rootfs signature at 0011A000!
no rootfs signature at 0011B000!
no rootfs signature at 0011C000!
no rootfs signature at 0011D000!
no rootfs signature at 0011E000!
no rootfs signature at 0011F000!
no rootfs signature at 00120000!
no rootfs signature at 00121000!
no rootfs signature at 00122000!
no rootfs signature at 00123000!
no rootfs signature at 00124000!
no rootfs signature at 00125000!
no rootfs signature at 00126000!
no rootfs signature at 00127000!
no rootfs signature at 00128000!
no rootfs signature at 00129000!
no rootfs signature at 0012A000!
no rootfs signature at 0012B000!
no rootfs signature at 0012C000!
no rootfs signature at 0012D000!
no rootfs signature at 0012E000!
no rootfs signature at 0012F000!
no rootfs signature at 00131000!
no rootfs signature at 00132000!
no rootfs signature at 00133000!
no rootfs signature at 00134000!
no rootfs signature at 00135000!
no rootfs signature at 00136000!
no rootfs signature at 00137000!
no rootfs signature at 00138000!
no rootfs signature at 00139000!
no rootfs signature at 0013A000!
no rootfs signature at 0013B000!
no rootfs signature at 0013C000!
no rootfs signature at 0013D000!
no rootfs signature at 0013E000!
no rootfs signature at 0013F000!
no rootfs signature at 00140000!
no rootfs signature at 00141000!
no rootfs signature at 00142000!
no rootfs signature at 00143000!
no rootfs signature at 00144000!
no rootfs signature at 00145000!
no rootfs signature at 00146000!
no rootfs signature at 00147000!
no rootfs signature at 00148000!
no rootfs signature at 00149000!
no rootfs signature at 0014A000!
no rootfs signature at 0014B000!
no rootfs signature at 0014C000!
no rootfs signature at 0014D000!
no rootfs signature at 0014E000!
no rootfs signature at 0014F000!
Jump to image start=0x80500000...
decompressing kernel:
Uncompressing Linux... done, booting the kernel.
done decompressing kernel.
start address: 0x80003400
Realtek WLAN driver - version 1.6 (2013-02-21)
Adaptivity function - version 7.1
#######################################################
SKB_BUF_SIZE=2408 MAX_SKB_NUM=480
#######################################################
Probing RTL8186 10/100 NIC-kenel stack size order...
chip name: 8196C, chip revid: 0
NOT YET
eth0 added. vid=1 Member port 0x1...
eth1 added. vid=2 Member port 0x10...
eth2 added. vid=1 Member port 0x2...
eth3 added. vid=1 Member port 0x4...
eth4 added. vid=1 Member port 0x8...
eth5 added. vid=1 Member port 0x0...
added, mapping to ...
zlr Creating 7 MTD partitions on "flash_bank_1":
WARNNING: find rootfs in:0x150000, real_offset:150000
0x000000000000-0x000000150000 : "boot+cfg+linux"
0x000000150000-0x000000740000 : "root fs"
0x0000007c0000-0x000000800000 : "parm flash"
0x000000000000-0x000000800000 : "all"
0x000000740000-0x0000007c0000 : "jffs2"
0x000000000000-0x0000000d0000 : "linux up"
0x0000000d0000-0x000000800000 : "rootfs up"
Realtek FastPath:v1.03
serial console detected.Disabling virtual terminals.
init started:BusyBox v1.00-pre8 (2014.08.14-10:37+0000) multi-call binary
Bummer, could not run '/etc/init.d/rcS': No such file or directory
BusyBox v1.00-pre8 (2014.08.14-10:37+0000) Built-in shell (msh)
Enter 'help' for a list of built-in commands.
mount -t jffs2 /dev/mtdblock4 /tmp/para status:0
ERROR: Invalid checksum of current setting! for HW from /dev/mtdblock2, offset:6, len:5522,
WARNNING: first 2048 bytes of /dev/mtdblock2: hw={
boardVer=1
nic0Addr=081079e3fd78
nic1Addr=0810117830c9
wlan={
0={
macAddr=081079e3fd79
macAddr1=081079e3fd80
macAddr2=081079e3fd81
macAddr3=081079e3fd82
macAddr4=081079e3fd83
macAddr5=081079e3fd84
macAddr6=08101781,
WARNNING: last 2048 bytes of /dev/mtdblock2: S_A=000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000,
WARNNING: try again, cnt:1,
ERROR: Invalid checksum of current setting! for HW from /dev/mtdblock2, offset:6, len:5522,
WARNNING: first 2048 bytes of /dev/mtdblock2: hw={
boardVer=1
nic0Addr=081079e3fd78
nic1Addr=0810117830c9
wlan={
0={
macAddr=081079e3fd79
macAddr1=081079e3fd80
macAddr2=081079e3fd81
macAddr3=081079e3fd82
macAddr4=081079e3fd83
macAddr5=081079e3fd84
macAddr6=08101781,
WARNNING: last 2048 bytes of /dev/mtdblock2: S_A=000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000,
ERROR: can't read args from /dev/mtdblock2. set->nam:HW, set->len:2317, set->offset:0,
ERROR: section:HW, will reset to default!,
@@@@@@@@@normal_reset_fun_of_section
ERROR: Invalid checksum of current setting! for HW from /dev/mtdblock2, offset:6, len:5522,
WARNNING: first 2048 bytes of /dev/mtdblock2: hw={
boardVer=1
nic0Addr=081079e3fd78
nic1Addr=0810117830c9
wlan={
0={
macAddr=081079e3fd79
macAddr1=081079e3fd80
macAddr2=081079e3fd81
macAddr3=081079e3fd82
macAddr4=081079e3fd83
macAddr5=081079e3fd84
macAddr6=08101781,
WARNNING: last 2048 bytes of /dev/mtdblock2: S_A=000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000,
WARNNING: try again, cnt:1,
ERROR: Invalid checksum of current setting! for HW from /dev/mtdblock2, offset:6, len:5522,
WARNNING: first 2048 bytes of /dev/mtdblock2: hw={
boardVer=1
nic0Addr=081079e3fd78
nic1Addr=0810117830c9
wlan={
0={
macAddr=081079e3fd79
macAddr1=081079e3fd80
macAddr2=081079e3fd81
macAddr3=081079e3fd82
macAddr4=081079e3fd83
macAddr5=081079e3fd84
macAddr6=08101781,
WARNNING: last 2048 bytes of /dev/mtdblock2: S_A=000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000,
ERROR: can't read args from /dev/mtdblock2. set->nam:HW, set->len:2317, set->offset:0,
Initialize AP HW MIB failed for writeDefault(), LINE:1667!
,
,
,
!!!!!olddefconf.ssid=NETCORE_2.4G
!!!!!olddefconf.ssid=NETCORE_2.4G
!!!!!olddefconf.ssid=NETCORE_2.4G-VAP1
!!!!!olddefconf.ssid=NETCORE_2.4G-VAP2
!!!!!olddefconf.ssid=NETCORE_2.4G-VAP3
!!!!!olddefconf.ssid=NETCORE_2.4G-VAP4
!!!!!olddefconf.ssid=NETCORE_2.4G
!!!!!olddefconf.ssid=NETCORE_2.4G
!!!!!olddefconf.ssid=NETCORE_2.4G-VAP1
!!!!!olddefconf.ssid=NETCORE_2.4G-VAP2
!!!!!olddefconf.ssid=NETCORE_2.4G-VAP3
!!!!!olddefconf.ssid=NETCORE_2.4G-VAP4
##############num:1677760575###############
###################ac_ip:169.254.96.65####################
ipadd is 192.168.1.254
@@@@@@@@@apmib_update set 1 @@@@@@@@@@@@@@@
@@@@@@/dev/mtdblock2
type:1, ret:1
@@@@@@@@@apmib_update set 2 @@@@@@@@@@@@@@@
@@@@@@/dev/mtdblock2
type:2, ret:1
@@@@@@@@@apmib_update set 4 @@@@@@@@@@@@@@@
@@@@@@/dev/mtdblock2
type:4, ret:1
, success of writeDefault
ERROR: section:HW, load default*************************************,
0072700727007270072700727normal_reset_fun_of_section
ERROR: Will reboot*************************************,
The system is going down NOW !!
Sending SIGTERM to all processes.
Terminated
733
wlan_check.sh: do nothing......
version_new=Netcore(NAP840+)CN-V1.2.42856,2018.04.03 10:16.
/proc/wps_btn_delay: cannot create
killall: xhcatv: no process killed
killall: multi_ppp: no process killed
killall: igmpproxy: no process killed
killall: udhcpc: no process killed
wlanapp_sh:1942:@@@@@@@####;wlan0
~~~~~~~~~~~~~~~~~~~~~~ssid=NETCORE_2.4G
initWlanstanum=0
MIB_HW_TX_POWER_CCK_A=2e2e2e2d2d2d2d2d2d2c2c2c2c2c
MIB_HW_TX_POWER_CCK_A_new=2e2e2e2d2d2d2d2d2d2c2c2c2c2c
MIB_HW_TX_POWER_HT40_1S_A=333232323231313130302f2f2e2e
MIB_HW_TX_POWER_HT40_1S_An=333232323231313130302f2f2e2e
MIB_HW_TX_POWER_HT20=0f0f0f0f0f0f0f0f0f0f0f0f0f0f
MIB_HW_TX_POWER_HT20n=0f0f0f0f0f0f0f0f0f0f0f0f0f0f
MIB_HW_TX_POWER_DIFF_OFDM=0102010101010101010102010202
MIB_HW_TX_POWER_DIFF_OFDMn=0102010101010101010102010202
initWlan:6172,wlan0-vxd is off
initWlan:6172,wlan0-va0 is off
initWlan:6172,wlan0-va1 is off
initWlan:6172,wlan0-va2 is off
initWlan:6172,wlan0-va3 is off
cmd=/bin/brctl addif br0 eth0
cmd=/sbin/ifconfig eth0 up
qvlan_set_write 785541 0 0 0 0 0 0 0 0 0
qvlan_set_write 785544 -1 -1 0 0 0 0 0 0 0
brctl setfd br0 0
brctl stp br0 0
Se▒Bummer, could not run '/sbin/swapoff': No such file or directory
Please stand by while rebooting the system.
Booting...
@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@
@
@ chip__no chip__id mfr___id dev___id cap___id size_sft dev_size chipSize
@ 0000000h 0ef4017h 00000efh 0000040h 0000017h 0000000h 0000017h 0800000h
@ blk_size blk__cnt sec_size sec__cnt pageSize page_cnt chip_clk chipName
@ 0010000h 0000080h 0001000h 0000800h 0000100h 0000010h 000003eh W25Q64
@
@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@
Reboot Result from Watchdog Timeout!
---RealTek(RTL8196D)at 2018.04.03-10:30+0800 v1.6b (579MHz)
====no sys signature at 00010000!cs6c
ret=0sys signature at 00010000!
====no sys signature at 00020000!cs6c
ret=0sys signature at 00020000!
ret=2sys signature at 00030000!
checksum sum 0, p_kernel_img 80500000, 00117882
no rootfs signature at 000E0000!
no rootfs signature at 000F0000!
no rootfs signature at 00130000!
no rootfs signature at 000E1000!
no rootfs signature at 000E2000!
no rootfs signature at 000E3000!
no rootfs signature at 000E4000!
no rootfs signature at 000E5000!
no rootfs signature at 000E6000!
no rootfs signature at 000E7000!
no rootfs signature at 000E8000!
no rootfs signature at 000E9000!
no rootfs signature at 000EA000!
no rootfs signature at 000EB000!
no rootfs signature at 000EC000!
no rootfs signature at 000ED000!
no rootfs signature at 000EE000!
no rootfs signature at 000EF000!
no rootfs signature at 000F1000!
no rootfs signature at 000F2000!
no rootfs signature at 000F3000!
no rootfs signature at 000F4000!
no rootfs signature at 000F5000!
no rootfs signature at 000F6000!
no rootfs signature at 000F7000!
no rootfs signature at 000F8000!
no rootfs signature at 000F9000!
no rootfs signature at 000FA000!
no rootfs signature at 000FB000!
no rootfs signature at 000FC000!
no rootfs signature at 000FD000!
no rootfs signature at 000FE000!
no rootfs signature at 000FF000!
no rootfs signature at 00100000!
no rootfs signature at 00101000!
no rootfs signature at 00102000!
no rootfs signature at 00103000!
no rootfs signature at 00104000!
no rootfs signature at 00105000!
no rootfs signature at 00106000!
no rootfs signature at 00107000!
no rootfs signature at 00108000!
no rootfs signature at 00109000!
no rootfs signature at 0010A000!
no rootfs signature at 0010B000!
no rootfs signature at 0010C000!
no rootfs signature at 0010D000!
no rootfs signature at 0010E000!
no rootfs signature at 0010F000!
no rootfs signature at 00110000!
no rootfs signature at 00111000!
no rootfs signature at 00112000!
no rootfs signature at 00113000!
no rootfs signature at 00114000!
no rootfs signature at 00115000!
no rootfs signature at 00116000!
no rootfs signature at 00117000!
no rootfs signature at 00118000!
no rootfs signature at 00119000!
no rootfs signature at 0011A000!
no rootfs signature at 0011B000!
no rootfs signature at 0011C000!
no rootfs signature at 0011D000!
no rootfs signature at 0011E000!
no rootfs signature at 0011F000!
no rootfs signature at 00120000!
no rootfs signature at 00121000!
no rootfs signature at 00122000!
no rootfs signature at 00123000!
no rootfs signature at 00124000!
no rootfs signature at 00125000!
no rootfs signature at 00126000!
no rootfs signature at 00127000!
no rootfs signature at 00128000!
no rootfs signature at 00129000!
no rootfs signature at 0012A000!
no rootfs signature at 0012B000!
no rootfs signature at 0012C000!
no rootfs signature at 0012D000!
no rootfs signature at 0012E000!
no rootfs signature at 0012F000!
no rootfs signature at 00131000!
no rootfs signature at 00132000!
no rootfs signature at 00133000!
no rootfs signature at 00134000!
no rootfs signature at 00135000!
no rootfs signature at 00136000!
no rootfs signature at 00137000!
no rootfs signature at 00138000!
no rootfs signature at 00139000!
no rootfs signature at 0013A000!
no rootfs signature at 0013B000!
no rootfs signature at 0013C000!
no rootfs signature at 0013D000!
no rootfs signature at 0013E000!
no rootfs signature at 0013F000!
no rootfs signature at 00140000!
no rootfs signature at 00141000!
no rootfs signature at 00142000!
no rootfs signature at 00143000!
no rootfs signature at 00144000!
no rootfs signature at 00145000!
no rootfs signature at 00146000!
no rootfs signature at 00147000!
no rootfs signature at 00148000!
no rootfs signature at 00149000!
no rootfs signature at 0014A000!
no rootfs signature at 0014B000!
no rootfs signature at 0014C000!
no rootfs signature at 0014D000!
no rootfs signature at 0014E000!
no rootfs signature at 0014F000!
Jump to image start=0x80500000...
decompressing kernel:
Uncompressing Linux... done, booting the kernel.
done decompressing kernel.
start address: 0x80003400
Realtek WLAN driver - version 1.6 (2013-02-21)
Adaptivity function - version 7.1
#######################################################
SKB_BUF_SIZE=2408 MAX_SKB_NUM=480
#######################################################
Probing RTL8186 10/100 NIC-kenel stack size order...
chip name: 8196C, chip revid: 0
NOT YET
eth0 added. vid=1 Member port 0x1...
eth1 added. vid=2 Member port 0x10...
eth2 added. vid=1 Member port 0x2...
eth3 added. vid=1 Member port 0x4...
eth4 added. vid=1 Member port 0x8...
eth5 added. vid=1 Member port 0x0...
added, mapping to ...
zlr Creating 7 MTD partitions on "flash_bank_1":
WARNNING: find rootfs in:0x150000, real_offset:150000
0x000000000000-0x000000150000 : "boot+cfg+linux"
0x000000150000-0x000000740000 : "root fs"
0x0000007c0000-0x000000800000 : "parm flash"
0x000000000000-0x000000800000 : "all"
0x000000740000-0x0000007c0000 : "jffs2"
0x000000000000-0x0000000d0000 : "linux up"
0x0000000d0000-0x000000800000 : "rootfs up"
Realtek FastPath:v1.03
serial console detected.Disabling virtual terminals.
init started:BusyBox v1.00-pre8 (2014.08.14-10:37+0000) multi-call binary
Bummer, could not run '/etc/init.d/rcS': No such file or directory
BusyBox v1.00-pre8 (2014.08.14-10:37+0000) Built-in shell (msh)
Enter 'help' for a list of built-in commands.
mount -t jffs2 /dev/mtdblock4 /tmp/para status:0
725
wlan_check.sh: do nothing......
version_new=Netcore(NAP840+)CN-V1.2.42856,2018.04.03 10:16.
/proc/wps_btn_delay: cannot create
killall: xhcatv: no process killed
killall: multi_ppp: no process killed
killall: igmpproxy: no process killed
killall: udhcpc: no process killed
wlanapp_sh:1942:@@@@@@@####;wlan0
~~~~~~~~~~~~~~~~~~~~~~ssid=NETCORE_2.4G
initWlanstanum=0
MIB_HW_TX_POWER_CCK_A=2e2e2e2d2d2d2d2d2d2c2c2c2c2c
MIB_HW_TX_POWER_CCK_A_new=2e2e2e2d2d2d2d2d2d2c2c2c2c2c
MIB_HW_TX_POWER_HT40_1S_A=333232323231313130302f2f2e2e
MIB_HW_TX_POWER_HT40_1S_An=333232323231313130302f2f2e2e
MIB_HW_TX_POWER_HT20=0f0f0f0f0f0f0f0f0f0f0f0f0f0f
MIB_HW_TX_POWER_HT20n=0f0f0f0f0f0f0f0f0f0f0f0f0f0f
MIB_HW_TX_POWER_DIFF_OFDM=0102010101010101010102010202
MIB_HW_TX_POWER_DIFF_OFDMn=0102010101010101010102010202
initWlan:6172,wlan0-vxd is off
initWlan:6172,wlan0-va0 is off
initWlan:6172,wlan0-va1 is off
initWlan:6172,wlan0-va2 is off
initWlan:6172,wlan0-va3 is off
cmd=/bin/brctl addif br0 eth0
cmd=/sbin/ifconfig eth0 up
qvlan_set_write 785541 0 0 0 0 0 0 0 0 0
qvlan_set_write 785544 -1 -1 0 0 0 0 0 0 0
brctl setfd br0 0
brctl stp br0 0
brctl addif br0 wlan0
/sbin/ifconfig wlan0 0.0.0.0
ifconfig br0 hw ether 08:10:11:00:03:04
/sbin/ifconfig br0 192.168.1.254
wlanapp_sh:1942:@@@@@@@####;wlan0 wlan0-va0 wlan0-va1 wlan0-va2 wlan0-va3 wlan0-vxd
Register to wlan0
iwcontrol RegisterPID to (wlan0)
SIOCDELRT: No such process
argc:3
open logs file
options_strings:c:fbH:h:i:np:qr:s:x:v:ld:a:u:
udhcp client (v0.9.9-pre) started
script is:/usr/share/udhcpc/br0.sh
IEEE 802.11f (IAPP) using interface br0 (v1.8)
@@@@@@rand=18
SIOCDELRT: No such process
SIOCDELRT: No such process
doamin=0
, not impl...
#########08:10:11:00:03:04########
#########host:772#############################
##############reply_ip:169.254.3.4######################
SIOCSIFFLAGS: Cannot assign requested address
========================END init.sh===============================
SIGNAl 17;reset_flag
/bin/udp_ap_handle MIMO : NAP840+
check_udp_ap_handle:udp_ap_handle running.....
killall: boa: no process killed
killall: boa: no process killed
/proc/sys/net/ipv4/ip_conntrack_max: cannot create
Starting Protocol Module: HTTP Server ... OK
/proc/sys/net/core/hot_list_length: cannot create
# Auto channel choose ch:5 2nd:0
translate_uri:222;Mozilla/5.0 (Windows NT 10.0; WOW64) AppleWebKit/537.36 (KHTML, like Gecko) Chrome/86.0.4240.198 Safari/537.36
translate_uri:254
本帖最后由 yanzihui 于 2022-8-27 08:54 编辑
NAP840+编程器固件 有好几个地方有MAC，并且是一批，wan、lan、wlan的。是不是只改了一处？
我有个NB1200GC的，备份了编程器固件，看了一下，不过没去改mac刷机，瞎猜的。 oujinlai 发表于 2022-11-6 15:59
有好几个地方有MAC，并且是一批，wan、lan、wlan的。是不是只改了一处？
我有个NB1200GC的，备份了编程 ...
你这个是路由器不是AP吧 不是，ap也差不多吧
页:
[1]