恩山无线论坛

标题: 智障音箱R1:TTL连接方式及波特率及MASKROM已找到 [打印本页]

作者: rush    时间: 2019-7-16 09:24
标题: 智障音箱R1:TTL连接方式及波特率及MASKROM已找到
本帖最后由 rush 于 2019-8-26 20:32 编辑

TTL
不得不说屎全家的匪讯公司在R1上面下足了功夫,通过图片可以观察到,我们的智障音箱R1,并没有使用常见UART0,使用的是UART1/2的复用IO,波特率为瑞芯微常见的 1500000
[attach]297913[/attach]
======================================================================

加装USB:掌握新姿势!(5V不需要接!只需连接Dm Dp GND)
[attach]304775[/attach]
======================================================================

MASKROM(救砖引导模式)
R211连接到EMMC的CLK,随便短接一头到地。CPU屏蔽盖就是地。短接开机就是MASKROM模式。

[attach]302998[/attach]

开机日志欣赏
  1. DDR Version V1.06 20171026
  2. In
  3. 300MHz
  4. DDR3
  5. Bus Width=16 Col=10 Bank=8 Row=15 CS=1 Die Bus-Width=16 Size=512MB
  6. mach:9
  7. OUT
  8. Boot1 Release Time: 2017-06-12, version: 2.37
  9. ChipType = 0xc, 281
  10. No.1 FLASH ID:11 ff ff ff ff ff
  11. SdmmcInit=2 0
  12. BootCapSize=2000
  13. UserCapSize=7456MB
  14. FwPartOffset=2000 , 2000
  15. SdmmcInit=0 2
  16. StorageInit ok = 29674
  17. SecureMode : SBOOT_MODE_NS
  18. Code check OK! theLoader 0x60000000, 40228
  19. Code check OK! theLoader 0x68400000, 50998
  20. Enter Trust OS
  21. INF TEE-CORE:init_primary_helper:319: Initializing (1.0.1-54-g0d46013 #4 Thu Sep                                                                                                                                                              29 01:09:49 UTC 2016 arm)
  22. INF TEE-CORE:init_primary_helper:320: Release version: 1.6
  23. INF TEE-CORE:init_teecore:79: teecore inits done


  24. U-Boot 2014.10-RK322X-06-gac2d183 (Apr 28 2018 - 10:50:08), Build: jenkins-R1-PV                                                                                                                                                             -3331

  25. CPU: rk322x
  26. cpu version = 3
  27. CPU's clock information:
  28.     arm pll = 600000000HZ
  29.     periph pll = 600000000HZ
  30.     ddr pll = 600000000HZ
  31.     codec pll = 500000000HZ
  32. Board:  Rockchip platform Board
  33. Uboot as second level loader
  34. DRAM:  Found dram banks: 1
  35. Adding bank:0000000060000000(0000000020000000)
  36. Reserve memory for trust os.
  37. dram reserve bank: base = 0x68400000, size = 0x00100000
  38. 128 MiB
  39. GIC CPU mask = 0x00000001
  40. rk dma pl330 version: 1.4
  41. remotectl v0.1
  42. pwm freq=0x11e1a3
  43. pwm_freq_nstime=0x355
  44. SdmmcInit = 0 20
  45. SdmmcInit = 2 0
  46. ERROR: v7_dcache_inval_range - start address is not aligned - 0x659bc58c
  47. ERROR: v7_dcache_inval_range - stop address is not aligned - 0x659bc78c
  48. storage init OK!
  49. Using default environment

  50. GetParam
  51. Load FDT from boot image.
  52. No pmic detect.
  53. power hold: bank-0 pin-30, active level-0
  54. set pwm voltage ok,pwm_id =1 vol=1100000,pwm_value=66
  55. set pwm voltage ok,pwm_id =2 vol=1200000,pwm_value=33
  56. DRAM: dram freq:786MHz
  57. SecureBootEn = 0, SecureBootLock = 0

  58. #Boot ver: 2018-04-04#2.37
  59. empty serial no.
  60. normal boot.
  61. checkKey
  62. multikey pressed:checkcnt=30 untouchCnt=3, presstime=0ms
  63. vbus = 1
  64. board_fbt_key_pressed: ir_keycode = 0x0, frt = 0
  65. no fuel gauge found
  66. no fuel gauge found
  67. can't find power_ctr node for lcdc0
  68. hdmi is disabled
  69. can't find dts node for deviceinfo
  70. rk_hdmi_register:fail to read deviceinfo
  71. hdmi baseparamer 0x0@0-0
  72. tve baseparamer 0x0@0-0
  73. Hdmi Devices Not Exist.
  74. can't find dts node for rk312x-tve
  75. rk312x-tve is disabled
  76. read logo on state from dts [1]
  77. no fuel gauge found
  78. checkKey
  79. multikey pressed:checkcnt=30 untouchCnt=3, presstime=0ms
  80. vbus = 1
  81. board_fbt_key_pressed: ir_keycode = 0x0, frt = 0
  82. rkloader_get_bootprop:i=0 unused
  83. rkloader_get_bootprop:failed
  84. getbootprop failed! ret = -1
  85. led on
  86. Hit any key to stop autoboot:  0
  87. Secure Boot state: 0
  88. kernel   @ 0x62000000 (0x00760118)
  89. ramdisk  @ 0x65bf0000 (0x0016c43c)
  90. bootrk: do_bootm_linux...
  91.    Loading Device Tree to 65600000, end 656165ab ... OK
  92. Add bank:0000000060000000, 0000000008400000
  93. Add bank:0000000068500000, 0000000017b00000

  94. Starting kernel ...

  95. <hit enter to activate fiq debugger>
  96. [    0.000000] Booting Linux on physical CPU 0xf00
  97. [    0.000000] Initializing cgroup subsys cpu
  98. [    0.000000] Initializing cgroup subsys cpuacct
  99. [    0.000000] Linux version 3.10.0 (jenkins@phicomm) (gcc version 4.6.x-google                                                                                                                                                              20120106 (prerelease) (GCC) ) #1 SMP PREEMPT Sat Apr 28 10:52:53 CST 2018
  100. [    0.000000] CPU: ARMv7 Processor [410fc075] revision 5 (ARMv7), cr=10c5387d
  101. [    0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instructio                                                                                                                                                             n cache
  102. [    0.000000] Machine: Rockchip RK3229, model: rockchip,rk3229
  103. [    0.000000] rockchip_uboot_logo_setup: mem: 0x02000000@0x7dc00000, offset:0x0                                                                                                                                                             1000000
  104. [    0.000000] hdmi init vic is 65536
  105. [    0.000000] cvbs init tve.format is -1
  106. [    0.000000] cvbs init tve.format is -1
  107. [    0.000000] cvbs init tve.format is -1
  108. [    0.000000] rockchip_uboot_mem_reserve: reserve 0x02000000@0x7dc00000 for ubo                                                                                                                                                             ot logo
  109. [    0.000000] rockchip_ion_reserve
  110. [    0.000000] ion heap(vmalloc): base(0) size(0) align(0)
  111. [    0.000000] cma: CMA: reserved 16 MiB at 7cc00000
  112. [    0.000000] Memory policy: ECC disabled, Data cache writealloc
  113. [    0.000000] psci: probing function IDs from device-tree
  114. [    0.000000] PERCPU: Embedded 9 pages/cpu @c1404000 s13440 r8192 d15232 u36864
  115. [    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pag                                                                                                                                                             es: 129792
  116. [    0.000000] Kernel command line: vmalloc=496M psci=enable rockchip_jtag conso                                                                                                                                                             le=ttyFIQ0 androidboot.selinux=permissive androidboot.hardware=rk30board android                                                                                                                                                             boot.console=ttyFIQ0 init=/init mtdparts=rk29xxnand:0x00002000@0x00002000(uboot)                                                                                                                                                             ,0x00004000@0x00004000(trust),0x00002000@0x00008000(misc),0x00000800@0x0000A000(                                                                                                                                                             baseparamer),0x00007800@0x0000A800(resource),0x00006000@0x00012000(kernel),0x000                                                                                                                                                             06000@0x00018000(boot),0x00010000@0x0001E000(recovery),0x00020000@0x0002E000(bac                                                                                                                                                             kup),0x00040000@0x0004E000(cache),0x001FE000@0x0008E000(userdata),0x00008000@0x0                                                                                                                                                             028C000(metadata),0x00002000@0x00296000(kpanic),0x00180000@0x00298000(system),0x                                                                                                                                                             00040000@0x00418000(private),-@0x00458000(user) storagemedia=emmc uboot_logo=0x0                                                                                                                                                             2000000@0x7dc00000:0x01000000 loader.timestamp=2018-04-28_10:50:08 hdmi.vic=6553                                                                                                                                                             6 tve.format=-1
  117. [    0.000000] rockchip jtag enabled
  118. [    0.000000] PID hash table entries: 2048 (order: 1, 8192 bytes)
  119. [    0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
  120. [    0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
  121. [    0.000000] allocated 1048576 bytes of page_cgroup
  122. [    0.000000] please try 'cgroup_disable=memory' option if you don't want memor                                                                                                                                                             y cgroups
  123. [    0.000000] Memory: 132MB 379MB = 511MB total
  124. [    0.000000] Memory: 450460k/450460k available, 72804k reserved, 0K highmem
  125. [    0.000000] Virtual kernel memory layout:
  126. [    0.000000]     vector  : 0xffff0000 - 0xffff1000   (   4 kB)
  127. [    0.000000]     fixmap  : 0xfff00000 - 0xfffe0000   ( 896 kB)
  128. [    0.000000]     vmalloc : 0xe0800000 - 0xff000000   ( 488 MB)
  129. [    0.000000]     lowmem  : 0xc0000000 - 0xe0000000   ( 512 MB)
  130. [    0.000000]     pkmap   : 0xbfe00000 - 0xc0000000   (   2 MB)
  131. [    0.000000]     modules : 0xbf000000 - 0xbfe00000   (  14 MB)
  132. [    0.000000]       .text : 0xc0008000 - 0xc0d157e4   (13366 kB)
  133. [    0.000000]       .init : 0xc0d16000 - 0xc0d74480   ( 378 kB)
  134. [    0.000000]       .data : 0xc0d76000 - 0xc0e99618   (1166 kB)
  135. [    0.000000]        .bss : 0xc0e99618 - 0xc0fc349c   (1192 kB)
  136. [    0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
  137. [    0.000000] Preemptible hierarchical RCU implementation.
  138. [    0.000000]  RCU dyntick-idle grace-period acceleration is enabled.
  139. [    0.000000] NR_IRQS:16 nr_irqs:16 16
  140. [    0.000000] rk_clk_tree_init start!
  141. [    0.000000] rk_get_uboot_display_flag: uboot_logo_on = 1
  142. [    0.000000] rkclk_init_clks: cnt_parent = 13
  143. [    0.000000] rkclk_init_clks: cnt_rate = 19
  144. [    0.000000] Architected cp15 timer(s) running at 24.00MHz (phys).
  145. [    0.000000] Switching to timer-based delay loop
  146. [    0.000000] sched_clock: ARM arch timer >56 bits at 24000kHz, resolution 41ns
  147. [    0.000000] process version: 0
  148. [    0.000000] channel:0, lkg:10
  149. [    0.000000] target-temp:95
  150. [    0.000000] channel:2, lkg:5
  151. [    0.000000] target-temp:0
  152. [    0.000000] channel:2, lkg:5
  153. [    0.000000] sched_clock: 32 bits at 100 Hz, resolution 10000000ns, wraps ever                                                                                                                                                             y 4294967286ms
  154. [    1.908255] Calibrating delay loop (skipped), value calculated using timer fr                                                                                                                                                             equency.. 48.00 BogoMIPS (lpj=240000)
  155. [    1.908280] pid_max: default: 32768 minimum: 301
  156. [    1.908479] Security Framework initialized
  157. [    1.908506] SELinux:  Initializing.
  158. [    1.908639] Mount-cache hash table entries: 512
  159. [    1.909695] Initializing cgroup subsys debug
  160. [    1.909718] Initializing cgroup subsys memory
  161. [    1.909764] Initializing cgroup subsys freezer
  162. [    1.909815] CPU: Testing write buffer coherency: ok
  163. [    1.910233] /cpus/cpu@0 missing clock-frequency property
  164. [    1.910257] /cpus/cpu@1 missing clock-frequency property
  165. [    1.910279] /cpus/cpu@2 missing clock-frequency property
  166. [    1.910298] /cpus/cpu@3 missing clock-frequency property

复制代码







作者: Star945    时间: 2019-7-16 09:31
这就是传说中的带佬早起搞机吗~
作者: smaillee    时间: 2019-7-16 09:37
R1继续吃灰中,不懂电路,纯支持
作者: 郁闷的毛毛虫    时间: 2019-7-16 10:04
终于有大佬开始研究R1了,支持一下!
作者: ashleyzz    时间: 2019-7-16 10:19
Rush大这是要出手了

作者: network007    时间: 2019-7-16 10:33
大佬出手 R1又要涨价了
作者: neczxnw    时间: 2019-7-16 10:48
等大神折腾了,小白跟风折腾下
作者: hmc801    时间: 2019-7-16 13:11
R1起死回生靠你了,期待你的R1固件哦
作者: huierwsh    时间: 2019-7-16 13:14

R1起死回生靠你了,期待你的R1固件哦

作者: deathsoul    时间: 2019-7-16 14:50
必须支持,不过r1既然是安卓,那我们还是可以继续尝试各种root方法来解决问题。TTL也许是最终方案。
作者: deathsoul    时间: 2019-7-16 14:52
这小板子没注意是多少层的PCB,没猜错的话,如果为了方便期维修,TTL也许直接藏在某个排线当中了。排除法找找看。
作者: lwjdyj    时间: 2019-7-16 17:22
我不懂,我很敬佩楼主,R1用的云知声,云知声提供开源,直接刷云知声行不,我不懂,我就一说,说错了别骂我。
作者: ajun02    时间: 2019-7-16 23:06
大佬一直用的你的t1固件精简流畅,就是休眠不知道怎么关

作者: eboloo    时间: 2019-7-17 00:29
佩服,跟定你了!
作者: xyli    时间: 2019-7-17 09:36
期待大佬有新进展
作者: xyafei    时间: 2019-7-17 09:43
顶起,期待更多操盘方法
作者: fsphm    时间: 2019-7-17 21:42
有大佬,跟着顶

作者: prioner    时间: 2019-7-17 21:49
骚呢,牛逼!
作者: 馄饨加蛋    时间: 2019-7-17 21:59
闲来无事搞基

作者: good123    时间: 2019-7-18 06:25
顶顶大佬大佬加油
作者: deathsoul    时间: 2019-7-18 23:19
deathsoul 发表于 2019-7-16 14:52
这小板子没注意是多少层的PCB,没猜错的话,如果为了方便期维修,TTL也许直接藏在某个排线当中了。排除法找 ...

有位点图么?有时间我拆个R1连上试试
作者: deathsoul    时间: 2019-7-18 23:21
deathsoul 发表于 2019-7-18 23:19
有位点图么?有时间我拆个R1连上试试

看到你更新的图了,哈哈!
作者: 壊人er    时间: 2019-7-19 10:56
支持支持!
作者: g0g002    时间: 2019-7-21 00:07
强烈支持楼主。
作者: cao2oem    时间: 2019-7-21 00:14
期待rush大神精品。
作者: wszzl    时间: 2019-7-21 11:25
终于有大佬开始研究R1了,支持一下!
作者: 731894915    时间: 2019-7-21 23:30
Mark!能root就好了
作者: 郁闷的毛毛虫    时间: 2019-7-24 19:24
看不懂帮忙顶帖!
作者: sangood    时间: 2019-7-25 11:35
帮忙顶下,有ttl,应该root就行了?
作者: cbl111    时间: 2019-7-25 20:59
期待大佬的研究成果,感谢!
作者: 271595667    时间: 2019-7-25 22:22
这是大师啊,你这样把设计师放在何地啊!

作者: 大黑屋    时间: 2019-7-26 08:51

终于有大佬开始研究R1了,支持一下!
作者: enroute    时间: 2019-7-26 22:51
期待固件。。。加油啊!

作者: wszzl    时间: 2019-7-28 08:49
R1起死回生靠你了,期待你的R1固件哦
作者: 731894915    时间: 2019-7-28 13:26
每天一看!!
作者: 113906217    时间: 2019-7-29 17:13
每天一顶 !
作者: gao198907    时间: 2019-7-30 00:04
顶顶顶顶顶

作者: ivenzhu    时间: 2019-7-30 16:02
智障r1吃灰快一年了,期待大神复活作品
作者: achaoge    时间: 2019-8-2 12:01
巨大巨大巨大的进步

不知道楼主是否可以焊接上 usb 口,看看能不能进入rk的 maskrom 模式?如果可以进入maskrom模式的话,估计就可以好好的玩了,直接丢弃斐迅的系统,上 linux 系统,可以参考 rpi 玩 google home了

eMMC Installation: https://github.com/jhswartz/rk3229/blob/master/EMMC-INSTALL.md
作者: 金金动听    时间: 2019-8-2 12:37
带大家一起搞机

作者: achaoge    时间: 2019-8-2 17:16
也就是说可以进入 maskrom 模式了?
有没有具体的操作方法?

心痒了,想拆一个玩。
作者: laikezhou    时间: 2019-8-3 15:46
搞起来,期待
作者: 欧阳小兔1    时间: 2019-8-9 17:07
希望能早日破解,能按上小爱同学就完美了
作者: duxiaodi888    时间: 2019-8-9 18:24
太牛逼了牛逼打发了
作者: liliangjun    时间: 2019-8-10 18:02
看起来很有希望,就等教程了,烙铁都准备好了
作者: enroute    时间: 2019-8-10 22:13
liliangjun 发表于 2019-8-10 18:02
看起来很有希望,就等教程了,烙铁都准备好了

不想硬改啊。。。

作者: liliangjun    时间: 2019-8-11 10:49
enroute 发表于 2019-8-10 22:13
不想硬改啊。。。

要拆下来刷机,用编程器

作者: enroute    时间: 2019-8-11 12:20
liliangjun 发表于 2019-8-11 10:49
要拆下来刷机,用编程器

也不知道进度怎么样了

作者: achaoge    时间: 2019-8-12 15:48
enroute 发表于 2019-8-10 22:13
不想硬改啊。。。

不硬改是不可能的。

已经刷入respeaker 的固件,系统可以起来,有点点希望。至少有一个可用的 linux 系统,网络也可以通。

现在需要搞定声音的相关驱动,输入和输出,就基本上可以搞其它的智能音箱系统了。
作者: enroute    时间: 2019-8-12 16:11
achaoge 发表于 2019-8-12 15:48
不硬改是不可能的。

已经刷入respeaker 的固件,系统可以起来,有点点希望。至少有一个可用的 linux  ...

Ttl刷入的吗?

作者: achaoge    时间: 2019-8-12 16:41
enroute 发表于 2019-8-12 16:11
Ttl刷入的吗?

TTL + USB,倒是可以不必动用编程器

接上 ttl 和 usb 后,reboot bootloader 或者按下板子上的一个按钮,应该就可以进入到 maskrom 模式,在这个模式下刷入 respeaker v2 的固件,重启在 u-boot 那里就有中断了,不过这个时候需要把波特率改成115200 才看得到。

在 u-boot 下面,通过 ums 0 mmc 0 命令,可以把 mmc 暴露给pc,在pc上就可以修改文件系统的内容了,需要把 rootfs 文件系统上的 boot/uEnv.txt 最后一行注释才可以正常到 linux 系统。

用 nmcli device wifi connect your_wifi_ssid password your_wifi_password 可以连网。

接下来需要折腾声音的驱动。
作者: enroute    时间: 2019-8-12 18:00
恭喜恭喜,又向前迈出了一步

作者: enroute    时间: 2019-8-12 18:02
achaoge 发表于 2019-8-12 16:41
TTL + USB,倒是可以不必动用编程器

接上 ttl 和 usb 后,reboot bootloader 或者按下板子上的一个按 ...

真是一波三折啊

作者: achaoge    时间: 2019-8-14 14:22
楼主,我手賤作死把 uboot 刷坏了,现在无法进系统,也无法进 maskrom 模式了。

楼主能帮忙把 emmc 的 clk 找出来吗?如果 emmc 的 clk 引出来了的话,就还可以进 maskrom 模式,那R1就怎么样都刷不死了,可以随便作了。

附件为三星 emmc 的信息
作者: zheng_pf19    时间: 2019-8-14 15:04
这硬改对我们小白有难度。
作者: lwchang    时间: 2019-8-15 13:19
看来有希望了
作者: fnkr52    时间: 2019-8-15 22:42
率全体恩山R1党以及党魁向你学习!
作者: qq40424024    时间: 2019-8-16 00:08
大佬威武。。。。
作者: qq40424024    时间: 2019-8-16 00:08
大佬威武。。。。
作者: ID10086    时间: 2019-8-16 14:15

R1起死回生靠你了,期待你的R1固件哦
作者: 一剑封侯    时间: 2019-8-16 14:20
继续 大神威武
作者: fnkr52    时间: 2019-8-19 12:48
为了不让R1变成电子垃圾。顶起
作者: Love满天下    时间: 2019-8-24 02:58
顶起啊  有希望了
作者: bruslau    时间: 2019-8-24 16:35
大佬 加油 喜欢你
作者: 心荡神驰    时间: 2019-8-26 14:34
终于有大佬开始研究R1了,支持一下!
作者: hhyyhh    时间: 2019-8-27 16:14
学习了学习了
作者: f474458424    时间: 2019-8-27 21:35
好可以的方式三分
作者: infi450    时间: 2019-8-31 21:37
感谢分享                                 
作者: 风丶不停    时间: 2019-9-1 17:21
        强大的恩山!(以下重复1万次)
作者: qingkingdom    时间: 2019-9-1 22:08
感谢大神的研究。。
作者: bruslau    时间: 2019-9-8 17:48
  大佬 加油 顶你们
作者: allen201601    时间: 2019-9-8 19:49
牛,。?!!!。。。????。。
作者: sepb    时间: 2019-9-9 16:52
这个不顶不行啊
作者: 惊破天    时间: 2019-9-10 22:08
留名坐等大神出手
作者: pcvia    时间: 2019-9-16 08:46
等大神折腾了,小白跟风折腾下
作者: wxzx88    时间: 2019-9-16 11:03
马上70周年国庆了,在此我祝你国庆节快乐!
作者: 嗯嗯嗯嗯    时间: 2019-9-27 21:59
楼主用TTL可以救砖吗,音箱变砖了一通电救自动进入MASKROM模式.用LINUX虚拟机救砖一执行./rkdeveloptool wl 0x0 full.img命令就卡死.固件是你另外一个帖子的ROOT魔改镜像
作者: rush    时间: 2019-9-28 08:35
嗯嗯嗯嗯 发表于 2019-9-27 21:59
楼主用TTL可以救砖吗,音箱变砖了一通电救自动进入MASKROM模式.用LINUX虚拟机救砖一执行./rkdeveloptool wl  ...

1,别相信他自动进入,一定要手工短接,这个现象在粒子云上面也有,一定自己去短接
2,说了多少次虚拟机不要用了,我用虚拟机就是会卡死的
作者: xtnnheeq    时间: 2019-9-28 13:29
智障R1能不能用 就看你了,
作者: eaglepeng    时间: 2019-9-28 14:19
小哥哥,ttl购买有啥要求码,看到啥电源时3V的  有的是5V的
作者: rush    时间: 2019-9-28 15:59
eaglepeng 发表于 2019-9-28 14:19
小哥哥,ttl购买有啥要求码,看到啥电源时3V的  有的是5V的

应该是3V的
作者: eaglepeng    时间: 2019-9-28 17:58
rush 发表于 2019-9-28 15:59
应该是3V的

哦哦哦哦哦,谢谢呢
作者: jason175    时间: 2019-10-4 15:38
很佩服敬仰这样的大神
作者: 阿帅    时间: 2019-10-14 14:24
R1起死回生靠你了,期待你的R1固件哦
作者: 纯洁公子    时间: 2019-10-15 00:34
牛逼!围观 ,厚着脸皮准备伸手了

作者: K2PB1    时间: 2019-10-19 00:30
大手笔~~后续继续跟进

作者: picc745514    时间: 2019-10-28 13:20
大佬期待救活智障
作者: 國龍    时间: 2019-11-4 11:36
感谢大佬,期待大佬的神作
作者: wang160251    时间: 2019-11-4 12:03
厉害厉害,大佬!
作者: laosui    时间: 2019-11-5 09:14
等大神折腾了,小白跟风折腾下
作者: 13902914555    时间: 2019-11-8 22:27
楼主技术棒棒的,赞一个
作者: etscript    时间: 2019-11-9 11:41
懂电路的真牛逼
作者: suntrian    时间: 2019-11-11 14:37
虽然看不懂,但还是要忍不住顶一下
作者: shuko    时间: 2019-11-11 15:46
率全体R1音箱党以及党魁向你学习!
作者: henllen520    时间: 2019-11-14 16:56
吃瓜观众,只看看不发表意见
作者: laosui    时间: 2019-11-19 11:15

R1起死回生靠你了,期待你的R1固件哦
作者: 老子不会兵法    时间: 2019-12-3 16:06
usb已经加装了  ttl怎么焊接
作者: wjgkx123    时间: 2020-1-8 11:29
本帖最后由 wjgkx123 于 2020-1-8 11:35 编辑

怎么和TTL连接,就接两根线吗?
[attach]335074[/attach]

作者: kmy143    时间: 2020-1-8 16:55
跟大佬中。谢谢大佬分享
作者: szwpolaris    时间: 2020-1-9 08:26
该大佬跪了




欢迎光临 恩山无线论坛 (https://www.right.com.cn/forum/) Powered by Discuz! X3.5