恩山无线论坛

 找回密码
 立即注册

QQ登录

只需一步,快速开始

搜索
12
返回列表 发新帖
楼主: 葛大师

hs8145v救砖步骤

[复制链接]
发表于 2019-8-13 02:51 | 显示全部楼层
买一个看看
我的恩山、我的无线 The best wifi forum is right here.
发表于 2019-8-14 10:47 | 显示全部楼层
等着你呢
我的恩山、我的无线 The best wifi forum is right here.
发表于 2019-8-15 13:55 | 显示全部楼层
针对刷机引起的不启动变砖机器,不保证任何机器能救砖成功 第一步确保nand没有硬伤
我的恩山、我的无线 The best wifi forum is right here.
发表于 2019-8-18 09:32 | 显示全部楼层
链接失效了楼主,请补下谢谢
我的恩山、我的无线 The best wifi forum is right here.
发表于 2019-8-18 15:26 | 显示全部楼层
文件消失了,重新补一个。
我的恩山、我的无线 The best wifi forum is right here.
发表于 2019-8-19 01:44 | 显示全部楼层
谢谢楼主的分享
我的恩山、我的无线 The best wifi forum is right here.
发表于 2019-8-19 01:45 | 显示全部楼层
文件过期~!!!!!!!!!!!!!!!!!!!!!!!
我的恩山、我的无线 The best wifi forum is right here.
发表于 2019-8-22 22:22 | 显示全部楼层

买一个看看
我的恩山、我的无线 The best wifi forum is right here.
发表于 2019-8-25 11:20 | 显示全部楼层
谢谢楼主,回去试试能否将板砖救回。
我的恩山、我的无线 The best wifi forum is right here.
发表于 2019-8-25 22:15 | 显示全部楼层
Use the UbootB to load success


U-Boot 2010.03 (R16C10 Jun 05 2016 - 20:39:18)

DRAM:  512 MB
Boot From NAND flash
Chip Type is SD5116T
NAND:  Special Nand id table Version 1.23
Nand ID: 0xC2 0xDA 0x90 0x95 0x06 0x00 0x00 0x00
now using default nand flash type, Block:128KB Page:2KB!
ECC Match pagesize:2K, oobzie:64, ecctype:4bit
Nand(Hardware): Block:128KB Page:2KB Chip:128MB*1 OOB:64B ECC:4bit
128 MiB
Using default environment

In:    serial
Out:   serial
Err:   serial
PHY power down !!!
[main.c__6080]::CRC:0x0, Magic1:0x0, Magic2:0x0, count:1, CommitedArea:0x0, Active:0x0, RunFlag:0x0
0x000000100000-0x000008000000 : "mtd=1"
UBI: attaching mtd1 to ubi0
UBI: empty MTD device detected
UBI: create volume table (copy #1)
UBI error: ubi_scan_get_free_peb: no eraseblocks found
UBI error: ubi_init: cannot attach mtd1
UBI error: ubi_init: UBI error: cannot initialize UBI, error -28
UBI init error -28
ERROR: failed to select 'ubifs' partition, please format it first!
Start from main system(0x0)!
CRC:0x0, Magic1:0x0, Magic2:0x0, count:1, CommitedArea:0x0, Active:0x0, RunFlag:0x0
0x000000100000-0x000008000000 : "mtd=1"
UBI: attaching mtd1 to ubi0
UBI: empty MTD device detected
UBI: create volume table (copy #1)
UBI error: ubi_scan_get_free_peb: no eraseblocks found
UBI error: ubi_init: cannot attach mtd1
UBI error: ubi_init: UBI error: cannot initialize UBI, error -28
UBI init error -28
ERROR: failed to select 'ubifs' partition, please format it first!
resetting ...


HuaWei StartCode 2012.02 (V300R017C10 Sep 07 2017 - 11:54:40)

NAND:  Nand ID: 0xC2 0xDA 0x90 0x95 0x06 0x00 0x00 0x00
ECC Match pagesize:2K, oobzie:64, ecctype:4bit
Nand(Hardware): 256 MiB
startcode select the uboot to load
the high RAM is :8080103c
startcode uboot boot count:0
Use the UbootB to load first
Use the UbootB to load success
我的恩山、我的无线 The best wifi forum is right here.
发表于 2019-8-25 22:15 | 显示全部楼层
还是不行。
我的恩山、我的无线 The best wifi forum is right here.
您需要登录后才可以回帖 登录 | 立即注册

本版积分规则

QQ|手机版|小黑屋|Archiver|恩山无线论坛(常州市恩山计算机开发有限公司版权所有) ( 苏ICP备05084872号 )

GMT+8, 2019-8-26 15:03

Powered by Discuz! X3.4

© 2001-2017 Comsenz Inc.

快速回复 返回顶部 返回列表