OpenWrt ar71xx系列 for BB r46516 4M

coolwei888

感谢楼主！刚看到有8m的固件，已经刷上8m的固件，看功能很强啊！！虽然还是识别和挂载不了u盘和硬盘，不排除是硬件问题。

系统系统名称 OpenWrt
路由型号 TP-Link TL-WR841N/ND v8  
固件版本 OpenWrt Attitude Adjustment rc1 r35093 4M / LuCI 0.11 Branch (0.11+svn9615)  
内核版本 3.3.8  
本地时间 Thu Sep 8 23:49:17 2011
运行时间 0h 5m 28s
平均负载 0.03, 0.17, 0.12


挂载点 信息：

挂载点
已挂载的文件系统
文件系统 挂载点 可用 已用
   
rootfs   /   1.84 MB / 2.06 MB   11% (224.00 KB)   
/dev/root   /rom   0.00 B / 5.00 MB   100% (5.00 MB)   
tmpfs   /tmp   29.55 MB / 30.19 MB   2% (660.00 KB)   
tmpfs   /dev   512.00 KB / 512.00 KB   0% (0.00 B)   
root   /tmp/root   30.10 MB / 30.19 MB   0% (92.00 KB)   
overlayfs:/tmp/root   /tmp/root   30.10 MB / 30.19 MB   0% (92.00 KB)   
/dev/mtdblock3   /overlay   1.84 MB / 2.06 MB   11% (224.00 KB)   
overlayfs:/overlay   /   1.84 MB / 2.06 MB   11% (224.00 KB)   
挂载点
配置存储设备挂载到文件系统中的位置和参数。
启用 设备 挂载点 文件系统 选项 Root 检查   
        

尚无任何配置

coolwei888

分别接上4g金士顿u盘 和 移动硬盘，未能识别。

内核日志：
[    0.000000] Linux version 3.3.8 (haxc@haxc-PC) (gcc version 4.6.3 20120201 (prerelease) (Linaro GCC 4.6-2012.02) ) #22 Sun Jan 13 21:36:25 CST 2013
[    0.000000] MyLoader: sysp=f81981b1, boardp=42ca486f, parts=50bd6c6c
[    0.000000] bootconsole [early0] enabled
[    0.000000] CPU revision is: 0001974c (MIPS 74Kc)
[    0.000000] SoC: Atheros AR9341 rev 1
[    0.000000] Clocks: CPU:535.000MHz, DDR:400.000MHz, AHB:200.000MHz, Ref:25.000MHz
[    0.000000] Determined physical RAM map:
[    0.000000]  memory: 04000000 @ 00000000 (usable)
[    0.000000] Initrd not found or empty - disabling initrd
[    0.000000] Zone PFN ranges:
[    0.000000]   Normal   0x00000000 -> 0x00004000
[    0.000000] Movable zone start PFN for each node
[    0.000000] Early memory PFN ranges
[    0.000000]     0: 0x00000000 -> 0x00004000
[    0.000000] On node 0 totalpages: 16384
[    0.000000] free_area_init_node: node 0, pgdat 802d2180, node_mem_map 81000000
[    0.000000]   Normal zone: 128 pages used for memmap
[    0.000000]   Normal zone: 0 pages reserved
[    0.000000]   Normal zone: 16256 pages, LIFO batch:3
[    0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
[    0.000000] pcpu-alloc: [0] 0
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 16256
[    0.000000] Kernel command line:  board=TL-WR841N-v8 console=ttyS0,115200 rootfstype=squashfs,jffs2 noinitrd
[    0.000000] PID hash table entries: 256 (order: -2, 1024 bytes)
[    0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
[    0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
[    0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
[    0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
[    0.000000] Writing ErrCtl register=00000000
[    0.000000] Readback ErrCtl register=00000000
[    0.000000] Memory: 61620k/65536k available (2101k kernel code, 3916k reserved, 405k data, 208k init, 0k highmem)
[    0.000000] SLUB: Genslabs=9, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[    0.000000] NR_IRQS:51
[    0.000000] Calibrating delay loop... 266.64 BogoMIPS (lpj=1333248)
[    0.080000] pid_max: default: 32768 minimum: 301
[    0.080000] Mount-cache hash table entries: 512
[    0.090000] NET: Registered protocol family 16
[    0.090000] gpiochip_add: registered GPIOs 0 to 22 on device: ath79

coolwei888

[    0.100000] MIPS: machine is TP-LINK TL-WR841N/ND v8
[    0.510000] bio: create slab <bio-0> at 0
[    0.520000] Switching to clocksource MIPS
[    0.530000] NET: Registered protocol family 2
[    0.530000] IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.530000] TCP established hash table entries: 2048 (order: 2, 16384 bytes)
[    0.540000] TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
[    0.540000] TCP: Hash tables configured (established 2048 bind 2048)
[    0.550000] TCP reno registered
[    0.550000] UDP hash table entries: 256 (order: 0, 4096 bytes)
[    0.560000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[    0.560000] NET: Registered protocol family 1
[    0.570000] PCI: CLS 0 bytes, default 32
[    0.580000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    0.590000] JFFS2 version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[    0.600000] msgmni has been set to 120
[    0.600000] io scheduler noop registered
[    0.610000] io scheduler deadline registered (default)
[    0.610000] Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled
[    0.640000] serial8250.0: ttyS0 at MMIO 0x18020000 (irq = 11) is a 16550A
[    0.650000] console [ttyS0] enabled, bootconsole disabled
[    0.660000] m25p80 spi0.0: found s25fl064k, expected m25p80
[    0.670000] m25p80 spi0.0: s25fl064k (8192 Kbytes)
[    0.670000] 6 tp-link partitions found on MTD device spi0.0
[    0.680000] Creating 6 MTD partitions on "spi0.0":
[    0.680000] 0x000000000000-0x000000020000 : "u-boot"
[    0.690000] 0x000000020000-0x0000000ffd64 : "kernel"
[    0.700000] mtd: partition "kernel" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
[    0.710000] 0x0000000ffd64-0x0000007f0000 : "rootfs"
[    0.720000] mtd: partition "rootfs" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
[    0.730000] mtd: partition "rootfs" set to be root filesystem
[    0.740000] mtd: partition "rootfs_data" created automatically, ofs=5E0000, len=210000
[    0.740000] 0x0000005e0000-0x0000007f0000 : "rootfs_data"
[    0.750000] 0x0000007f0000-0x000000800000 : "art"
[    0.760000] 0x000000020000-0x0000007f0000 : "firmware"
[    0.760000] 0x000000000000-0x000000800000 : "fullflash"
[    0.790000] ag71xx_mdio: probed
[    0.800000] eth0: Atheros AG71xx at 0xb9000000, irq 4
[    1.350000] ag71xx ag71xx.0: eth0: connected to PHY at ag71xx-mdio.1:00 [uid=004dd042, driver=Generic PHY]
[    1.360000] eth1: Atheros AG71xx at 0xba000000, irq 5
[    1.920000] eth1: Found an AR934X built-in switch
[    2.950000] TCP cubic registered
[    2.950000] NET: Registered protocol family 17
[    2.950000] 8021q: 802.1Q VLAN Support v1.8
[    2.970000] VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
[    2.970000] Freeing unused kernel memory: 208k freed
[    4.920000] Registered led device: tp-link:green:lan1
[    4.920000] Registered led device: tp-link:green:lan2
[    4.920000] Registered led device: tp-link:green:lan3
[    4.930000] Registered led device: tp-link:green:lan4
[    4.930000] Registered led device: tp-link:green:qss
[    4.930000] Registered led device: tp-link:green:system
[    4.930000] Registered led device: tp-link:green:wan
[    4.930000] Registered led device: tp-link:green:wlan
[   10.140000] Compat-drivers backport release: compat-drivers-2012-09-04-2-gddac993
[   10.140000] Backport based on wireless-testing.git master-2012-09-07
[   10.150000] compat.git: wireless-testing.git
[   10.180000] cfg80211: Calling CRDA to update world regulatory domain
[   10.190000] cfg80211: World regulatory domain updated:
[   10.190000] cfg80211:   (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[   10.200000] cfg80211:   (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[   10.210000] cfg80211:   (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[   10.220000] cfg80211:   (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[   10.230000] cfg80211:   (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[   10.230000] cfg80211:   (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[   10.630000] SCSI subsystem initialized
[   10.830000] usbcore: registered new interface driver usbfs
[   10.830000] usbcore: registered new interface driver hub
[   10.840000] usbcore: registered new device driver usb
[   11.700000] usbcore: registered new interface driver rt73usb
[   11.730000] usbcore: registered new interface driver rtl8187
[   11.760000] ath: EEPROM regdomain: 0x0
[   11.760000] ath: EEPROM indicates default country code should be used
[   11.760000] ath: doing EEPROM country->regdmn map search
[   11.760000] ath: country maps to regdmn code: 0x3a
[   11.760000] ath: Country alpha2 being used: US
[   11.760000] ath: Regpair used: 0x3a
[   11.770000] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
[   11.770000] Registered led device: ath9k-phy0
[   11.770000] ieee80211 phy0: Atheros AR9340 Rev:0 mem=0xb8100000, irq=47
[   11.780000] cfg80211: Calling CRDA for country: US
[   11.780000] cfg80211: Regulatory domain changed to country: US
[   11.790000] cfg80211:   (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[   11.800000] cfg80211:   (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2700 mBm)
[   11.800000] cfg80211:   (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 1700 mBm)
[   11.810000] cfg80211:   (5250000 KHz - 5330000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[   11.820000] cfg80211:   (5490000 KHz - 5600000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[   11.830000] cfg80211:   (5650000 KHz - 5710000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[   11.840000] cfg80211:   (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 3000 mBm)
[   11.870000] usbcore: registered new interface driver rt2800usb
[   12.580000] PPP generic driver version 2.4.2
[   12.890000] ip_tables: (C) 2000-2006 Netfilter Core Team
[   13.180000] NET: Registered protocol family 24
[   13.380000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[   13.480000] nf_conntrack version 0.5.0 (966 buckets, 3864 max)
[   14.150000] xt_time: kernel timezone is -0000
[   15.000000] uhci_hcd: USB Universal Host Controller Interface driver
[   15.180000] usbcore: registered new interface driver usblp
[   15.240000] Initializing USB Mass Storage driver...
[   15.250000] usbcore: registered new interface driver usb-storage
[   15.260000] USB Mass Storage support registered.
[   15.360000] usbcore: registered new interface driver ums-alauda
[   15.380000] usbcore: registered new interface driver ums-cypress
[   15.400000] usbcore: registered new interface driver ums-datafab
[   15.420000] usbcore: registered new interface driver ums-freecom
[   15.440000] usbcore: registered new interface driver ums-isd200
[   15.460000] usbcore: registered new interface driver ums-jumpshot
[   15.490000] usbcore: registered new interface driver ums-karma
[   15.510000] usbcore: registered new interface driver ums-sddr09
[   15.530000] usbcore: registered new interface driver ums-sddr55
[   15.550000] usbcore: registered new interface driver ums-usbat
[   15.640000] usbcore: registered new interface driver zd1211rw
[   15.750000] fuse init (API version 7.18)
[   21.700000] device eth1 entered promiscuous mode
[   22.340000] eth1: link up (1000Mbps/Full duplex)
[   22.340000] br-lan: port 1(eth1) entered forwarding state
[   22.350000] br-lan: port 1(eth1) entered forwarding state
[   24.350000] br-lan: port 1(eth1) entered forwarding state
[   26.080000] device wlan0 entered promiscuous mode
[   26.280000] br-lan: port 2(wlan0) entered forwarding state
[   26.280000] br-lan: port 2(wlan0) entered forwarding state
[   28.280000] br-lan: port 2(wlan0) entered forwarding state
[   41.080000] jffs2_scan_eraseblock(): End of filesystem marker found at 0x0
[   41.100000] jffs2_build_filesystem(): unlocking the mtd device... done.
[   41.100000] jffs2_build_filesystem(): erasing all blocks after the end marker... done.
[   46.240000] JFFS2 notice: (1997) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found.

shb110119

8M的是否有多拨?

coolwei888

shb110119 发表于 2013-1-13 22:46
8M的是否有多拨?

有，楼主编译水平很高啊，集成了很多功能，很期待楼主的完美固件！！

网络 目录下有：
接口
无线
交换机
DHCP/DNS
主机名
静态路由
防火墙
多拨
网络诊断
Wondershaper
网络唤醒
Emong's Qos

shb110119

coolwei888 发表于 2013-1-13 22:59
有，楼主编译水平很高啊，集成了很多功能，很期待楼主的完美固件！！

网络 目录下有：

发现是有多拨，，不过我从LOG里看，，发现生成的几个虚拟的网并没有一直拨号。。
不知道是否我设置有问题

shb110119

额，可能是我的设置不对，，更正为下面设置，，LOG里有发现另几个虚拟的在一直拨号，我这边的多拨情况跟别人有点不同。。刚开始拨不上是正常的，只要有一直持续拨号几天，最终都会上的

haxc

coolwei888 发表于 2013-1-13 22:42
感谢楼主！刚看到有8m的固件，已经刷上8m的固件，看功能很强啊！！虽然还是识别和挂载不了u盘和硬盘，不排除 ...

由于我的300r没有改usb，所以测试不了，usb驱动和ext，fat32，ntfs我在8m都集成有了的，4m的就只有ext和fat32

你的u盘和移动硬盘是什么格式的阿？
挂载信息在系统日志底下查看

haxc

shb110119 发表于 2013-1-13 23:46
额，可能是我的设置不对，，更正为下面设置，，LOG里有发现另几个虚拟的在一直拨号，我这边的多拨情况跟别人 ...

你的路由有usb接口吗？看看能不能自动挂载上

shb110119

haxc 发表于 2013-1-13 23:56
由于我的300r没有改usb，所以测试不了，usb驱动和ext，fat32，ntfs我在8m都集成有了的，4m的就只有ext和 ...

我的3420刷了楼主的8M版，，发现EXT3的硬盘，也没有识别到。还有一个NTFS的16U盘也没有识别。还有主页那边的WAN显示也有问题，当如果是VTH拨上号。。WAN没有拨上的时候。。主页那边无法显示WAN。。其实可以设置为最后连上线的那个的IP也可以，或者都显示

最后问一下楼主，虚拟出来的VHT 的MAC地址在哪里修改。。不论是LUCI和/etc/config下的network、macvlan 都没有看到相关的参数

haxc

shb110119 发表于 2013-1-14 00:01
我的3420刷了楼主的8M版，，发现EXT3的硬盘，也没有识别到。还有一个NTFS的16U盘也没有识别。还有主页那边 ...

多拨的那个我真不懂，usb我查查什么问题

box2

ext3的支持不支持啊

shb110119

haxc 发表于 2013-1-14 00:25
多拨的那个我真不懂，usb我查查什么问题

我原来刷的固件。虚拟的VH是可以在MACVLAN里看到虚拟的MAC，并且可以修改

还有，我找了下软件包，3.3.8没发现在2.X.X内核时代用的NWAN或者multiwan
当时的IPK估计不兼容吧

coolwei888

haxc 发表于 2013-1-14 00:25
多拨的那个我真不懂，usb我查查什么问题

太感谢了！usb硬盘能挂载就爽了，到时候麻烦您再加上samba pt ftp等磁盘应用就是个完美固件了！

shb110119

coolwei888 发表于 2013-1-14 00:52
太感谢了！usb硬盘能挂载就爽了，到时候麻烦您再加上samba pt ftp等磁盘应用就是个完美固件了！

还有USHARE