|
hg255电信原版UBOOT刷机,本来好发了的。结果下载了openwrt官网的,0508-openwrt-ramips-rt305x-hg255d-squashfs-tftp.bin
固件升级…………完了。不起了。砖了…………
终端显示:
U-Boot 1.1.3 (Jan 16 2011 - 04:42:38)
Board: Ralink APSoC DRAM: 32 MB
relocate_code Pointer at: 81fb0000
config usb..
The Flash ID =0000227E
flash_protect ON: from 0xBF000000 to 0xBF01D43B
protect on 0
*** Warning - bad CRC, using default environment
============================================
Ralink UBoot Version: 3.3
--------------------------------------------
ASIC 3052_MP2 (Port5<->None)
DRAM component: 128 Mbits
DRAM bus: 32 bit
Total memory: 32 MBytes
Flash component: NOR Flash
Date:Jan 16 2011 Time:04:42:38
============================================
icache: sets:256, ways:4, linesz:32 ,total:32768
dcache: sets:128, ways:4, linesz:32 ,total:16384
##### The CPU freq = 384 MHZ ####
SDRAM bus set to 32 bit
SDRAM size =32 Mbytes
@Start First PHY modio study cmd.
eth_register
Eth0 (10/100-M)
enetvar=ethaddr,Eth addr:00:AA:BB:CCD:10
00:AA:BB:CCD:10:
eth_current->name = Eth0 (10/100-M)
netboot_common, argc= 2
*************buf = 0x81fcd5e0
**********NexTxPacket = 81fe4680
NetTxPacket = 0x81FE4680
NetRxPackets[0] = 0x81FE4C80
NetRxPackets[1] = 0x81FE5280
NetRxPackets[2] = 0x81FE5880
NetRxPackets[3] = 0x81FE5E80
NetRxPackets[4] = 0x81FE6480
NetRxPackets[5] = 0x81FE6A80
NetRxPackets[6] = 0x81FE7080
NetRxPackets[7] = 0x81FE7680
NetRxPackets[8] = 0x81FE7C80
NetRxPackets[9] = 0x81FE8280
NetRxPackets[10] = 0x81FE8880
NetRxPackets[11] = 0x81FE8E80
NetRxPackets[12] = 0x81FE9480
NetRxPackets[13] = 0x81FE9A80
NetRxPackets[14] = 0x81FEA080
NetRxPackets[15] = 0x81FEA680
NetRxPackets[16] = 0x81FEAC80
NetRxPackets[17] = 0x81FEB280
NetRxPackets[18] = 0x81FEB880
NetRxPackets[19] = 0x81FEBE80
KSEG1ADDR(NetTxPacket) = 0xA1FE4680
NetLoop,call eth_halt !
NetLoop,call eth_init !
Trying Eth0 (10/100-M)
Waitting for RX_DMA_BUSY status Start... done
Header Payload scatter function is Disable !!
ETH_STATE_ACTIVE!!
Please choose the operation:
1: Load system code to SDRAM via TFTP.
2: Load system code then write to Flash via TFTP.
3: Boot system code via Flash (default).
4: Entr boot command line interface.
9: Load Boot Loader code then write to Flash via TFTP.
You choosed 4
eth_register
Eth0 (10/100-M)
enetvar=ethaddr,Eth addr:00:AA:BB:CCD:10
00:AA:BB:CCD:10:
eth_current->name = Eth0 (10/100-M)
4: System Enter Boot Command Line Interface.
U-Boot 1.1.3 (Jan 16 2011 - 04:42:38)
main_loop !!
RT3052 # 44
Unknown command '44' - try 'help'
RT3052 # setenv serverip 192.168.1.100
RT3052 # tftpboot 0x80100000 u-boot-rom-hg255d.bin
netboot_common, argc= 3
*************buf = 0x81fcd5e0
**********NexTxPacket = 81fe4680
NetTxPacket = 0x81FE4680
NetRxPackets[0] = 0x81FE4C80
NetRxPackets[1] = 0x81FE5280
NetRxPackets[2] = 0x81FE5880
NetRxPackets[3] = 0x81FE5E80
NetRxPackets[4] = 0x81FE6480
NetRxPackets[5] = 0x81FE6A80
NetRxPackets[6] = 0x81FE7080
NetRxPackets[7] = 0x81FE7680
NetRxPackets[8] = 0x81FE7C80
NetRxPackets[9] = 0x81FE8280
NetRxPackets[10] = 0x81FE8880
NetRxPackets[11] = 0x81FE8E80
NetRxPackets[12] = 0x81FE9480
NetRxPackets[13] = 0x81FE9A80
NetRxPackets[14] = 0x81FEA080
NetRxPackets[15] = 0x81FEA680
NetRxPackets[16] = 0x81FEAC80
NetRxPackets[17] = 0x81FEB280
NetRxPackets[18] = 0x81FEB880
NetRxPackets[19] = 0x81FEBE80
KSEG1ADDR(NetTxPacket) = 0xA1FE4680
NetLoop,call eth_halt !
NetLoop,call eth_init !
Trying Eth0 (10/100-M)
Waitting for RX_DMA_BUSY status Start... done
Header Payload scatter function is Disable !!
ETH_STATE_ACTIVE!!
TFTP from server 192.168.1.100; our IP address is 192.168.1.1
Filename 'u-boot-rom-hg255d.bin'.
TIMEOUT_COUNT=10,Load address: 0x80100000
Loading: *
ArpTimeoutCheck
ArpTimeoutCheck
T T T Got ARP REQUEST, return our IP
checksum bad
checksum bad
T Got ARP REPLY, set server/gtwy eth addr (00:50:8d:54:05:da)
Got it
T #
first block received
############################
done
Bytes transferred = 145524 (23874 hex)
NetBootFileXferSize= 00023874
RT3052 #
|
|