|
编译的多个版本的,9331 USB网卡 不能挂载 帮忙分析下原因,挂U盘都正常的,编译应该加的组件都有了,挂上 USB无线网卡就是不正常,以前编译841 都可以用的。。晕的
[ 0.000000] Linux version 3.6.11 (liu@ubuntu) (gcc version 4.6.4 20121210 (prerelease) (Linaro GCC 4.6-2012.12) ) #1 Mon Jan 14 19:16:08 PST 2013
[ 0.000000] MyLoader: sysp=00d73bc7, boardp=ed0c292e, parts=97cba183
[ 0.000000] bootconsole [early0] enabled
[ 0.000000] CPU revision is: 00019374 (MIPS 24Kc)
[ 0.000000] SoC: Atheros AR9330 rev 1
[ 0.000000] Clocks: CPU:400.000MHz, DDR:400.000MHz, AHB:200.000MHz, Ref:25.000MHz
[ 0.000000] Determined physical RAM map:
[ 0.000000] memory: 04000000 @ 00000000 (usable)
[ 0.000000] Initrd not found or empty - disabling initrd
[ 0.000000] Zone ranges:
[ 0.000000] Normal [mem 0x00000000-0x03ffffff]
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x00000000-0x03ffffff]
[ 0.000000] On node 0 totalpages: 16384
[ 0.000000] free_area_init_node: node 0, pgdat 802d53a0, node_mem_map 81000000
[ 0.000000] Normal zone: 128 pages used for memmap
[ 0.000000] Normal zone: 0 pages reserved
[ 0.000000] Normal zone: 16256 pages, LIFO batch:3
[ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
[ 0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
[ 0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
[ 0.000000] pcpu-alloc: [0] 0
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 16256
[ 0.000000] Kernel command line: board=TL-WR741ND-v4 console=ttyATH0,115200 rootfstype=squashfs,jffs2 noinitrd
[ 0.000000] PID hash table entries: 256 (order: -2, 1024 bytes)
[ 0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
[ 0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.000000] __ex_table already sorted, skipping sort
[ 0.000000] Writing ErrCtl register=00000000
[ 0.000000] Readback ErrCtl register=00000000
[ 0.000000] Memory: 61604k/65536k available (2121k kernel code, 3932k reserved, 397k data, 212k init, 0k highmem)
[ 0.000000] SLUB: Genslabs=9, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[ 0.000000] NR_IRQS:51
[ 0.080000] Calibrating delay loop... 265.42 BogoMIPS (lpj=1327104)
[ 0.080000] pid_max: default: 32768 minimum: 301
[ 0.080000] Mount-cache hash table entries: 512
[ 0.090000] NET: Registered protocol family 16
[ 0.090000] MIPS: machine is TP-LINK TL-WR741ND v4
[ 0.550000] bio: create slab <bio-0> at 0
[ 0.550000] Switching to clocksource MIPS
[ 0.560000] NET: Registered protocol family 2
[ 0.560000] TCP established hash table entries: 2048 (order: 2, 16384 bytes)
[ 0.570000] TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.570000] TCP: Hash tables configured (established 2048 bind 2048)
[ 0.580000] TCP: reno registered
[ 0.580000] UDP hash table entries: 256 (order: 0, 4096 bytes)
[ 0.590000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[ 0.600000] NET: Registered protocol family 1
[ 0.600000] PCI: CLS 0 bytes, default 32
[ 0.620000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.620000] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 0.630000] msgmni has been set to 120
[ 0.640000] io scheduler noop registered
[ 0.640000] io scheduler deadline registered (default)
[ 0.650000] Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled
[ 0.650000] ar933x-uart: ttyATH0 at MMIO 0x18020000 (irq = 11) is a AR933X UART
[ 0.660000] console [ttyATH0] enabled, bootconsole disabled
[ 0.670000] ath79-spi ath79-spi: master is unqueued, this is deprecated
[ 0.680000] m25p80 spi0.0: found s25sl032a, expected m25p80
[ 0.680000] m25p80 spi0.0: s25sl032a (4096 Kbytes)
[ 0.690000] 5 tp-link partitions found on MTD device spi0.0
[ 0.690000] Creating 5 MTD partitions on "spi0.0":
[ 0.700000] 0x000000000000-0x000000020000 : "u-boot"
[ 0.700000] 0x000000020000-0x0000000fd23c : "kernel"
[ 0.710000] mtd: partition "kernel" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
[ 0.720000] 0x0000000fd23c-0x0000003f0000 : "rootfs"
[ 0.730000] mtd: partition "rootfs" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
[ 0.740000] mtd: partition "rootfs" set to be root filesystem
[ 0.750000] mtd: partition "rootfs_data" created automatically, ofs=3D0000, len=20000
[ 0.750000] 0x0000003d0000-0x0000003f0000 : "rootfs_data"
[ 0.760000] 0x0000003f0000-0x000000400000 : "art"
[ 0.770000] 0x000000020000-0x0000003f0000 : "firmware"
[ 0.790000] libphy: ag71xx_mdio: probed
[ 0.790000] eth0: Atheros AG71xx at 0xba000000, irq 5, mode:GMII
[ 1.350000] eth0: Found an AR7240/AR9330 built-in switch
[ 2.380000] eth1: Atheros AG71xx at 0xb9000000, irq 4, mode:MII
[ 2.930000] ag71xx ag71xx.0: eth1: connected to PHY at ag71xx-mdio.1:04 [uid=004dd041, driver=Generic PHY]
[ 2.940000] TCP: cubic registered
[ 2.940000] NET: Registered protocol family 17
[ 2.950000] 8021q: 802.1Q VLAN Support v1.8
[ 2.960000] VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
[ 2.970000] Freeing unused kernel memory: 212k freed
[ 6.420000] Registered led device: tp-link:green:lan1
[ 6.420000] Registered led device: tp-link:green:lan2
[ 6.420000] Registered led device: tp-link:green:lan3
[ 6.420000] Registered led device: tp-link:green:lan4
[ 6.420000] Registered led device: tp-link:green:qss
[ 6.420000] Registered led device: tp-link:green:system
[ 6.420000] Registered led device: tp-link:green:wan
[ 6.420000] Registered led device: tp-link:green:wlan
[ 6.420000] leds-gpio: probe of leds-gpio failed with error -16
[ 6.850000] eth0: link up (1000Mbps/Full duplex)
[ 9.960000] eth0: link down
[ 12.280000] Compat-drivers backport release: compat-drivers-2013-01-08-3
[ 12.280000] Backport based on wireless-testing.git master-2013-01-07
[ 12.290000] compat.git: wireless-testing.git
[ 12.330000] cfg80211: Calling CRDA to update world regulatory domain
[ 12.330000] cfg80211: World regulatory domain updated:
[ 12.340000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[ 12.350000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 12.350000] cfg80211: (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[ 12.360000] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[ 12.370000] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 12.380000] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 12.910000] SCSI subsystem initialized
[ 13.090000] usbcore: registered new interface driver usbfs
[ 13.090000] usbcore: registered new interface driver hub
[ 13.100000] usbcore: registered new device driver usb
[ 13.860000] ath: EEPROM regdomain: 0x0
[ 13.860000] ath: EEPROM indicates default country code should be used
[ 13.860000] ath: doing EEPROM country->regdmn map search
[ 13.860000] ath: country maps to regdmn code: 0x3a
[ 13.860000] ath: Country alpha2 being used: US
[ 13.860000] ath: Regpair used: 0x3a
[ 13.870000] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
[ 13.870000] Registered led device: ath9k-phy0
[ 13.870000] ieee80211 phy0: Atheros AR9330 Rev:1 mem=0xb8100000, irq=2
[ 13.870000] cfg80211: Calling CRDA for country: US
[ 13.880000] cfg80211: Regulatory domain changed to country: US
[ 13.880000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[ 13.890000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2700 mBm)
[ 13.900000] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 1700 mBm)
[ 13.910000] cfg80211: (5250000 KHz - 5330000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 13.920000] cfg80211: (5490000 KHz - 5600000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 13.920000] cfg80211: (5650000 KHz - 5710000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 13.930000] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 3000 mBm) |
|