哪位大神有TP-LINK WDR5620 V1.0版的编程器固件

ouji***

朋友给了一台WDR5620 V1.0版路由，看着是7628AN+7612EN+8M+64M，原机固件比较简单，想着刷机。

拆下gigadriver的8M闪存，用341A备份编程器固件，却怎么也不认芯片，选GD25Q64备份，读出来的全是FF。也不知是闪存被静电烧坏了还是341A不认识这个芯片。

没办法，用一块W25Q128刷了oye的breed-mt7628-oye-0006.bin。可以正常使用这个breed。

于是各种固件刷个遍，老毛子和小米nano的可以用，但没有eeprom，mac是乱的，也没有5G，2.4G也不稳定。

看看哪位大侠备份了原机的编程器固件，提取eeprom试下，实在不行就恢复成原厂固件算了。
别担心，我会改成我自己的mac再刷的，不会有冲突。

yj496***

mtk不是有通用eeprom嘛

ouji***

把K2的eeprom刷进去，在breed里填4个mac，还是没有5G.

jb***

还是备份原厂的吧，是不是没装好，不行换个编程器

laok***

编程器不认，焊路由上认吗

xia***

链接: https://pan.baidu.com/s/1eRBCZVs 提取码: cxrr

ouji***

laokuazi 发表于 2019-10-17 10:59
编程器不认，焊路由上认吗

焊上也不行，没反映。

ouji***

xiaomm 发表于 2019-10-17 10:59
链接: https://pan.baidu.com/s/1eRBCZVs 提取码: cxrr

谢谢你，
下载回来用winhex打开，里面全是FF。
我的姿势不对吗？

ouji***

刷HC5761A_3.4.3.9-099有5G没信号.trx，有5G菜单，没5G信号。

xia***

试试这个https://www.right.com.cn/forum/thread-360745-1-1.html

ouji***

谢谢！
现在2.4G信号还可以，快速ping，50万个包丢包率0.06%。
没有5G,是不是没正确到位到5G的相关参数。我已经把eproom里的0x0008000~0x00081ff内容复制到0x0002000那里了，也没有效果。
下面是老毛子的启动日志。我也看不明白。大神给分析分析：
Jan  1 00:00:04 syslogd started: BusyBox v1.24.2
Jan  1 00:00:04 HC5761A: firmware version: 3.4.3.9-099_28e0957
Jan  1 00:00:04 kernel: klogd started: BusyBox v1.24.2 (2019-01-27 05:25:38 CST)
Jan  1 00:00:04 kernel: Linux version 3.4.113 (padavan@hms) (gcc version 4.4.7 (GCC) ) #5 Sun Jan 27 09:21:09 CST 2019
Jan  1 00:00:04 kernel: MediaTek SoC: MT7628A, RevID: 0102, RAM: DDR2, XTAL: 40MHz
Jan  1 00:00:04 kernel: CPU/OCP/SYS frequency: 580/193/193 MHz
Jan  1 00:00:04 kernel: CPU revision is: 00019655 (MIPS 24KEc)
Jan  1 00:00:04 kernel: Determined physical RAM map:
Jan  1 00:00:04 kernel:  memory: 08000000 @ 00000000 (usable)
Jan  1 00:00:04 kernel: Zone PFN ranges:
Jan  1 00:00:04 kernel:   Normal   0x00000000 -> 0x00008000
Jan  1 00:00:04 kernel: Movable zone start PFN for each node
Jan  1 00:00:04 kernel: Early memory PFN ranges
Jan  1 00:00:04 kernel:     0: 0x00000000 -> 0x00008000
Jan  1 00:00:04 kernel: On node 0 totalpages: 32768
Jan  1 00:00:04 kernel: free_area_init_node: node 0, pgdat 80352880, node_mem_map 81000000
Jan  1 00:00:04 kernel:   Normal zone: 256 pages used for memmap
Jan  1 00:00:04 kernel:   Normal zone: 0 pages reserved
Jan  1 00:00:04 kernel:   Normal zone: 32512 pages, LIFO batch:7
Jan  1 00:00:04 kernel: Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
Jan  1 00:00:04 kernel: Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
Jan  1 00:00:04 kernel: pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
Jan  1 00:00:04 kernel: pcpu-alloc: [0] 0
Jan  1 00:00:04 kernel: Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 32512
Jan  1 00:00:04 kernel: Kernel command line: console=ttyS0,115200n8 root=/dev/mtdblock4 rootfstype=squashfs
Jan  1 00:00:04 kernel: PID hash table entries: 512 (order: -1, 2048 bytes)
Jan  1 00:00:04 kernel: Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
Jan  1 00:00:04 kernel: Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
Jan  1 00:00:04 kernel: Writing ErrCtl register=00078f20
Jan  1 00:00:04 kernel: Readback ErrCtl register=00078f20
Jan  1 00:00:04 kernel: Memory: 126240k/131072k available (2899k kernel code, 4832k reserved, 504k data, 180k init, 0k highmem)
Jan  1 00:00:04 kernel: NR_IRQS:40
Jan  1 00:00:04 kernel: console [ttyS0] enabled
Jan  1 00:00:04 kernel: Calibrating delay loop... 385.02 BogoMIPS (lpj=770048)
Jan  1 00:00:04 kernel: pid_max: default: 32768 minimum: 301
Jan  1 00:00:04 kernel: Mount-cache hash table entries: 512
Jan  1 00:00:04 kernel: NET: Registered protocol family 16
Jan  1 00:00:04 kernel: bio: create slab <bio-0> at 0
Jan  1 00:00:04 kernel: SCSI subsystem initialized
Jan  1 00:00:04 kernel: usbcore: registered new interface driver usbfs
Jan  1 00:00:04 kernel: usbcore: registered new interface driver hub
Jan  1 00:00:04 kernel: usbcore: registered new device driver usb
Jan  1 00:00:04 kernel: PCI host bridge to bus 0000:00
Jan  1 00:00:04 kernel: pci_bus 0000:00: root bus resource [mem 0x20000000-0x2fffffff]
Jan  1 00:00:04 kernel: pci_bus 0000:00: root bus resource [io  0x10160000-0x1016ffff]
Jan  1 00:00:04 kernel: pci 0000:00:00.0: [14c3:0801] type 01 class 0x060400
Jan  1 00:00:04 kernel: pci 0000:00:00.0: reg 0x10: [mem 0x00000000-0x7fffffff]
Jan  1 00:00:04 kernel: pci 0000:00:00.0: supports D1
Jan  1 00:00:04 kernel: pci 0000:00:00.0: PME# supported from D0 D1 D3hot
Jan  1 00:00:04 kernel: pci 0000:00:00.0: bridge configuration invalid ([bus 00-00]), reconfiguring
Jan  1 00:00:04 kernel: pci 0000:01:00.0: [14c3:7662] type 00 class 0x028000
Jan  1 00:00:04 kernel: pci 0000:01:00.0: reg 0x10: [mem 0x00000000-0x000fffff 64bit]
Jan  1 00:00:04 kernel: pci 0000:01:00.0: reg 0x30: [mem 0x00000000-0x0000ffff pref]
Jan  1 00:00:04 kernel: pci 0000:01:00.0: PME# supported from D0 D3hot D3cold
Jan  1 00:00:04 kernel: pci 0000:00:00.0: BAR 0: can't assign mem (size 0x80000000)
Jan  1 00:00:04 kernel: pci 0000:00:00.0: BAR 8: assigned [mem 0x20000000-0x200fffff]
Jan  1 00:00:04 kernel: pci 0000:00:00.0: BAR 9: assigned [mem 0x20100000-0x201fffff pref]
Jan  1 00:00:04 kernel: pci 0000:01:00.0: BAR 0: assigned [mem 0x20000000-0x200fffff 64bit]
Jan  1 00:00:04 kernel: pci 0000:01:00.0: BAR 6: assigned [mem 0x20100000-0x2010ffff pref]
Jan  1 00:00:04 kernel: pci 0000:00:00.0: PCI bridge to [bus 01-01]
Jan  1 00:00:04 kernel: pci 0000:00:00.0:   bridge window [mem 0x20000000-0x200fffff]
Jan  1 00:00:04 kernel: pci 0000:00:00.0:   bridge window [mem 0x20100000-0x201fffff pref]
Jan  1 00:00:04 kernel: PCI: Enabling device 0000:00:00.0 (0000 -> 0002)
Jan  1 00:00:04 kernel: Switching to clocksource MIPS
Jan  1 00:00:04 kernel: NET: Registered protocol family 2
Jan  1 00:00:04 kernel: IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
Jan  1 00:00:04 kernel: TCP established hash table entries: 4096 (order: 3, 32768 bytes)
Jan  1 00:00:04 kernel: TCP bind hash table entries: 4096 (order: 2, 16384 bytes)
Jan  1 00:00:04 kernel: TCP: Hash tables configured (established 4096 bind 4096)
Jan  1 00:00:04 kernel: TCP: reno registered
Jan  1 00:00:04 kernel: UDP hash table entries: 256 (order: 0, 4096 bytes)
Jan  1 00:00:04 kernel: NET: Registered protocol family 1
Jan  1 00:00:04 kernel: PCI: CLS 32 bytes, default 32
Jan  1 00:00:04 kernel: squashfs: version 4.0 (2009/01/31) Phillip Lougher
Jan  1 00:00:04 kernel: msgmni has been set to 246
Jan  1 00:00:04 kernel: io scheduler noop registered (default)
Jan  1 00:00:04 kernel: Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled
Jan  1 00:00:04 kernel: serial8250: ttyS0 at MMIO 0x10000c00 (irq = 28) is a 16550A
Jan  1 00:00:04 kernel: Ralink GPIO driver initialized. Number of GPIO: 64, GPIO mode: 55144455
Jan  1 00:00:04 kernel: loop: module loaded
Jan  1 00:00:04 kernel: Compaq SMART2 Driver (v 2.6.0)
Jan  1 00:00:04 kernel: HP CISS Driver (v 3.6.26)
Jan  1 00:00:04 kernel: mtip32xx Version 1.2.6os3
Jan  1 00:00:04 kernel: MediaTek SPI flash driver, SPI clock: 48MHz
Jan  1 00:00:04 kernel: SPI flash chip: W25Q128FV (ef 40180000) (16384 Kbytes)
Jan  1 00:00:04 kernel: Creating 7 MTD partitions on "raspi":
Jan  1 00:00:04 kernel: 0x000000000000-0x000000030000 : "Bootloader"
Jan  1 00:00:04 kernel: 0x000000030000-0x000000040000 : "Config"
Jan  1 00:00:04 kernel: 0x000000040000-0x000000050000 : "Factory"
Jan  1 00:00:04 kernel: 0x000000050000-0x00000017e3d0 : "Kernel"
Jan  1 00:00:04 kernel: 0x00000017e3d0-0x000000f80000 : "RootFS"
Jan  1 00:00:04 kernel: 0x000000f80000-0x000001000000 : "Storage"
Jan  1 00:00:04 kernel: 0x000000050000-0x000000f80000 : "Firmware_Stub"
Jan  1 00:00:04 kernel: tun: Universal TUN/TAP device driver, 1.6
Jan  1 00:00:04 kernel: tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
Jan  1 00:00:04 kernel: Ralink APSoC Ethernet Driver v3.2.4 (raeth)
Jan  1 00:00:04 kernel: raeth: PDMA RX ring 256, PDMA TX ring 256. Max packet size 1536
Jan  1 00:00:04 kernel: raeth: NAPI support, weight 32
Jan  1 00:00:04 kernel: raeth: Byte Queue Limits (BQL) support
Jan  1 00:00:04 kernel: PPP generic driver version 2.4.2
Jan  1 00:00:04 kernel: PPP MPPE Compression module registered
Jan  1 00:00:04 kernel: NET: Registered protocol family 24
Jan  1 00:00:04 kernel: p p t p driver version 0.8.5
Jan  1 00:00:04 kernel: Initializing USB Mass Storage driver...
Jan  1 00:00:04 kernel: usbcore: registered new interface driver usb-storage
Jan  1 00:00:04 kernel: USB Mass Storage support registered.
Jan  1 00:00:04 kernel: usbcore: registered new interface driver libusual
Jan  1 00:00:04 kernel: nf_conntrack version 0.5.0 (16384 buckets, 32768 max)
Jan  1 00:00:04 kernel: xt_time: kernel timezone is -0000
Jan  1 00:00:04 kernel: Bridge firewalling registered
Jan  1 00:00:04 kernel: gre: GRE over IPv4 demultiplexor driver
Jan  1 00:00:04 kernel: ip_tables: (C) 2000-2006 Netfilter Core Team
Jan  1 00:00:04 kernel: TCP: cubic registered
Jan  1 00:00:04 kernel: NET: Registered protocol family 10
Jan  1 00:00:04 kernel: ip6_tables: (C) 2000-2006 Netfilter Core Team
Jan  1 00:00:04 kernel: IPv6 over IPv4 tunneling driver
Jan  1 00:00:04 kernel: NET: Registered protocol family 17
Jan  1 00:00:04 kernel: L2TP core driver, V2.0
Jan  1 00:00:04 kernel: PPPoL2TP kernel driver, V2.0
Jan  1 00:00:04 kernel: 8021q: 802.1Q VLAN Support v1.8
Jan  1 00:00:04 kernel: ASUS NVRAM, v0.08. Available space: 61440. Integrity: OK
Jan  1 00:00:04 kernel: VFS: Mounted root (squashfs filesystem) readonly on device 31:4.
Jan  1 00:00:04 kernel: Freeing unused kernel memory: 180k freed
Jan  1 00:00:04 kernel: Algorithmics/MIPS FPU Emulator v1.5
Jan  1 00:00:04 kernel: MT7628 AP Driver version: 4.1.0.0
Jan  1 00:00:04 kernel: mtk-sd: MediaTek SD/MMC Card driver init
Jan  1 00:00:04 kernel: usbcore: registered new interface driver usblp
Jan  1 00:00:04 kernel: ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
Jan  1 00:00:04 kernel: U2PHY P0 set SRCTRL calibration value: 6
Jan  1 00:00:04 kernel: ehci-platform ehci-platform: Generic Platform EHCI Controller
Jan  1 00:00:04 kernel: ehci-platform ehci-platform: new USB bus registered, assigned bus number 1
Jan  1 00:00:04 kernel: ehci-platform ehci-platform: irq 26, io mem 0x101c0000
Jan  1 00:00:04 kernel: ehci-platform ehci-platform: USB 2.0 started, EHCI 1.00, overcurrent ignored
Jan  1 00:00:04 kernel: usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
Jan  1 00:00:04 kernel: usb usb1: Product: Generic Platform EHCI Controller
Jan  1 00:00:04 kernel: usb usb1: Manufacturer: Linux 3.4.113 ehci_hcd
Jan  1 00:00:04 kernel: usb usb1: SerialNumber: ehci-platform
Jan  1 00:00:04 kernel: hub 1-0:1.0: USB hub found
Jan  1 00:00:04 kernel: hub 1-0:1.0: 1 port detected
Jan  1 00:00:04 kernel: ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
Jan  1 00:00:04 kernel: ohci-platform ohci-platform: Generic Platform OHCI Controller
Jan  1 00:00:04 kernel: ohci-platform ohci-platform: new USB bus registered, assigned bus number 2
Jan  1 00:00:04 kernel: ohci-platform ohci-platform: irq 26, io mem 0x101c1000
Jan  1 00:00:04 kernel: usb usb2: New USB device found, idVendor=1d6b, idProduct=0001
Jan  1 00:00:04 kernel: usb usb2: Product: Generic Platform OHCI Controller
Jan  1 00:00:04 kernel: usb usb2: Manufacturer: Linux 3.4.113 ohci_hcd
Jan  1 00:00:04 kernel: usb usb2: SerialNumber: ohci-platform
Jan  1 00:00:04 kernel: hub 2-0:1.0: USB hub found
Jan  1 00:00:04 kernel: hub 2-0:1.0: 1 port detected
Jan  1 00:00:04 kernel: MTK AES Engine Module, HW verson: 04
Jan  1 00:00:04 kernel: AES Engine: register cbc(aes) crypto api
Jan  1 00:00:04 kernel: AES Engine: register ecb(aes) crypto api
Jan  1 00:00:04 kernel: Netfilter messages via NETLINK v0.30.
Jan  1 00:00:04 kernel: ip_set: protocol 6
Jan  1 00:00:04 kernel: raeth: HW IP/TCP/UDP checksum RX offload enabled
Jan  1 00:00:04 kernel: mtk_esw - hw bridge: W|LLLL
Jan  1 00:00:04 kernel: mtk_esw - set broadcast storm control rate as: 10 mbps
Jan  1 00:00:04 kernel: device eth2.1 entered promiscuous mode
Jan  1 00:00:04 kernel: device eth2 entered promiscuous mode
Jan  1 00:00:08 kernel: mtk_esw: Link Status Changed - Port WAN Link Up
Jan  1 00:00:08 kernel:  ch1 bssid=88:25:93:cd:c7:b0
Jan  1 00:00:08 kernel:  ch1 bssid=44:97:5a:27:84:94
Jan  1 00:00:08 kernel:  ch2 bssid=74:7d:24:9d:6b:44
Jan  1 00:00:08 kernel:  ch4 bssid=2c:b2:1a:a9:38:42
Jan  1 00:00:08 kernel:  ch5 bssid=b0:53:65:d0:0a:66
Jan  1 00:00:08 kernel:  ch6 bssid=2e:b2:1a:e6:df:10
Jan  1 00:00:08 kernel:  ch6 bssid=4c:e9:e4:bd:75:ce
Jan  1 00:00:08 kernel:  ch6 bssid=d8:15:0d:86:d3:58
Jan  1 00:00:08 kernel:  ch6 bssid=4c:e9:e4:bd:75:cc
Jan  1 00:00:08 kernel:  ch6 bssid=00:6b:8e:6c:a6:de
Jan  1 00:00:08 kernel:  ch10 bssid=74:c3:30:f4:2f:b0
Jan  1 00:00:08 kernel:  ch10 bssid=68:db:54:6a:65:f7
Jan  1 00:00:08 kernel:  ch10 bssid=76:7d:24:68:a1:28
Jan  1 00:00:08 kernel:  ch10 bssid=58:d9:d5:d5:f9:d8
Jan  1 00:00:08 kernel:  ch10 bssid=74:7d:24:68:a1:28
Jan  1 00:00:08 kernel:  ch11 bssid=44:97:5a:27:83:24
Jan  1 00:00:08 kernel:  ch11 bssid=74:7d:24:bb:4e:0c
Jan  1 00:00:08 kernel:  ch11 bssid=54:75:95:81:ea:c0
Jan  1 00:00:08 kernel:  ch11 bssid=68:db:54:fc:5e:37
Jan  1 00:00:08 kernel:  ch11 bssid=34:ce:00:47:53:a8
Jan  1 00:00:08 kernel:  ch13 bssid=e4:f3:f5:a6:15:28
Jan  1 00:00:08 kernel: =====================================================
Jan  1 00:00:08 kernel: Channel 1 : Dirty = 226, False CCA = 0, Busy Time = 31045, Skip Channel = FALSE
Jan  1 00:00:08 kernel: Channel 2 : Dirty = 296, False CCA = 0, Busy Time = 25913, Skip Channel = FALSE
Jan  1 00:00:08 kernel: Channel 3 : Dirty = 268, False CCA = 0, Busy Time = 3681, Skip Channel = FALSE
Jan  1 00:00:08 kernel: Channel 4 : Dirty = 328, False CCA = 0, Busy Time = 2854, Skip Channel = FALSE
Jan  1 00:00:08 kernel: Channel 5 : Dirty = 326, False CCA = 0, Busy Time = 4487, Skip Channel = FALSE
Jan  1 00:00:08 kernel: Channel 6 : Dirty = 550, False CCA = 0, Busy Time = 7744, Skip Channel = FALSE
Jan  1 00:00:08 kernel: Channel 7 : Dirty = 432, False CCA = 0, Busy Time = 2423, Skip Channel = FALSE
Jan  1 00:00:08 kernel: Channel 8 : Dirty = 444, False CCA = 0, Busy Time = 1201, Skip Channel = FALSE
Jan  1 00:00:08 kernel: Channel 9 : Dirty = 460, False CCA = 0, Busy Time = 4176, Skip Channel = FALSE
Jan  1 00:00:08 kernel: Channel 10 : Dirty = 644, False CCA = 0, Busy Time = 6100, Skip Channel = FALSE
Jan  1 00:00:08 kernel: Channel 11 : Dirty = 548, False CCA = 0, Busy Time = 6415, Skip Channel = FALSE
Jan  1 00:00:08 kernel: Channel 12 : Dirty = 332, False CCA = 0, Busy Time = 1155, Skip Channel = TRUE
Jan  1 00:00:08 kernel: Channel 13 : Dirty = 330, False CCA = 0, Busy Time = 2346, Skip Channel = TRUE
Jan  1 00:00:08 kernel: =====================================================
Jan  1 00:00:08 kernel: Rule 1 CCA value : Min Dirtiness (Include extension channel) ==> Select Channel 1
Jan  1 00:00:08 kernel: Min Dirty = 552
Jan  1 00:00:08 kernel: ExChannel = 5 , 0
Jan  1 00:00:08 kernel: BW        = 40
Jan  1 00:00:08 kernel: device ra0 entered promiscuous mode
Jan  1 00:00:09 kernel: br0: port 2(ra0) entered forwarding state
Jan  1 00:00:09 kernel: br0: port 1(eth2.1) entered forwarding state
Jan  1 00:00:09 kernel: mtk_esw - software IGMP/MLD snooping: 1
Jan  1 00:00:10 dnsmasq[482]: started, version 2.78 cachesize 1024
Jan  1 00:00:10 dnsmasq[482]: compile time options: IPv6 GNU-getopt no-RTC no-DBus no-i18n no-IDN DHCP DHCPv6 no-Lua TFTP no-conntrack ipset no-auth no-DNSSEC no-

loop-detect no-inotify
Jan  1 00:00:10 dnsmasq-dhcp[482]: DHCP, IP range 192.168.8.2 -- 192.168.8.244, lease time 1d
Jan  1 00:00:10 dnsmasq-dhcp[482]: DHCP, sockets bound exclusively to interface br0
Jan  1 00:00:10 dnsmasq[482]: read /etc/hosts - 3 addresses
Jan  1 00:00:10 dnsmasq[482]: read /etc/storage/dnsmasq/hosts - 0 addresses
Jan  1 00:00:10 dnsmasq-dhcp[482]: read /etc/dnsmasq/dhcp/dhcp-hosts.rc
Jan  1 00:00:10 DHCP WAN Client: starting on eth2.2 ...
Jan  1 00:00:10 DHCP WAN Client: bound (eth2.2), IP: 192.168.3.129, GW: 192.168.3.1, lease time: 86400
Jan  1 00:00:10 HC5761A: WAN up (eth2.2)
Jan  1 00:00:10 dnsmasq[482]: read /etc/hosts - 3 addresses
Jan  1 00:00:10 dnsmasq[482]: read /etc/storage/dnsmasq/hosts - 0 addresses
Jan  1 00:00:10 dnsmasq-dhcp[482]: read /etc/dnsmasq/dhcp/dhcp-hosts.rc
Jan  1 00:00:10 dnsmasq[482]: using nameserver 192.168.3.1#53
Jan  1 00:00:10 httpd[508]: Server listening port 80 (HTTP).
Jan  1 00:00:11 sshd[528]: Server listening on :: port 22.
Jan  1 00:00:11 sshd[528]: Server listening on 0.0.0.0 port 22.
Jan  1 00:00:11 miniupnpd[530]: version 2.0 starting UPnP-IGD ext if eth2.2 BOOTID=1420041611
Jan  1 00:00:11 miniupnpd[530]: HTTP listening on port 41520
Jan  1 00:00:11 kernel: br0: port 2(ra0) entered forwarding state
Jan  1 00:00:11 kernel: br0: port 1(eth2.1) entered forwarding state
Jan  1 00:00:21 NTP Client: Synchronizing time to ntp1.aliyun.com.
Jan  1 00:00:21 WiFi scheduler: 5GHz radio: ON
Oct 17 16:41:51 NTP Client: System time changed, offset: 151260088.899495s

linksy***

xiaomm 发表于 2019-10-17 10:59
链接: https://pan.baidu.com/s/1eRBCZVs 提取码: cxrr

呵呵，没备份对，下载后没打开看过吗？

linksy***

oujinlai 发表于 2019-10-17 17:19
谢谢！
现在2.4G信号还可以，快速ping，50万个包丢包率0.06%。
没有5G,是不是没正确到位到5G的相关参数。 ...

EERPOM数据导入到闪存的7F0000位置上。

ouji***

7f0000在固件区啊？也就是说要备份编程器固件，在把64k的eeporm导到7F0000？
eeprom不是在40000~4ffff么？
Jan  1 00:00:04 kernel: 0x000000040000-0x000000050000 : "Factory"

ouji***

linksys_wifi 发表于 2019-10-17 17:31
EERPOM数据导入到闪存的7F0000位置上。

由于我刷的是老毛子，固件13M多，用的是16M的闪存。7F0000上有固件数据。
按推理，我把FF0000和FF8000都换上了5G的数据，依旧不行。
我截取的5G代码是这个，不知对不对呢？