[已解决]belkin7231-4p为什么挂不了kingmax的1g？

131***

有点怪。已经成功挂到一个256m的u盘，但是1g的kingmax却挂不到。是什么原因呢？

解决方案[希望各位都能加载到大u盘]:
如4楼所说,可能是分区表坏了。先fdisk,后mkfs.ext2.我是在ubuntu下操作的.
fdisk -l
我的u盘识别为/dev/sdb1
1.输入“p”并按回车键显示U盘上的分区状态。可以输入“d”命令删除已有的分区，在显示的类似“partition number(1-4):”的提示符后，按“1”键再按回车键删除它，同样方法，删除其他分区。
2.输入“n”命令创建新分区，在接下来的提示中选择“p”命令设置主分区：按“1”键选择第1个分区；按回车键使用默认的磁盘柱面数；我是按defalut来分的.
3.重新回到“Command (m for help:)”提示符下，按“a”键设置活动分区，按“1”键选择第1分区。回到“Command (m for help:)”提示符下，按“t”键改变分区文件系统，按“6”键将文件系统设置为FAT16格式（若按“l”键可显示全部分区类型的代码）。
4.继续执行“n”命令创建其他分区，输入“p”选择主分区，再选择“2”创建第2个分区，按两次回车键使用默认的柱面数和大小(因为前面我第1个分了最多,所以已经没得分了)。最后按“w”键将上述设置真正写入分区表中，至此便完成了分区操作

执行“umount /dev/sdb1”命令，确定已解除U盘的挂接。接着执行“mkfs.ext2 /dev/sdb1”命令，即可将U盘的第1个分区格式化成ext2格式。


dmesg信息:
  Vendor: KINGMAX   Model: USB2.0 Flashdisk  Rev: 2.00
  Type:   Direct-Access                      ANSI SCSI revision: 02
Attached scsi removable disk sda at scsi0, channel 0, id 0, lun 0
SCSI device sda: 2015231 512-byte hdwr sectors (1032 MB)
sda: Write Protect is off
Partition check:
/dev/scsi/host0/bus0/target0/lun0: p1
WARNING: USB Mass Storage data integrity not assured
USB Mass Storage device found at 2
FAT: bogus logical sector size 0

[ 本帖最后由 1314258 于 2007-12-10 11:06 编辑 ]

阿***

分区表被破坏了，建议到linux中重新分区然后格式化。

scu***

跟容量无关吧。

你的两个u盘是不是同一个牌子的？

是不是驱动不支持kingmax？

阿***

不一定是驱动不支持，我一个金士顿的也一样，分区表被破坏了，格成FAT、ext都不行，最后在linux修复了一下可以认出来了。

131***

我就在ubuntu下格式化的.
mkfs.ext3 /dev/sdb1

131***

也有可能如阿键所说,怎么修复，给个命令

阿***

先fdisk

s***

同样的牌子，我用Paragon Partition Manager 7.0

格的，还是失败

hli***

不可能吧，我kingmax 2G挂了上去一点问题没有，你是不是水货的

s***

http://auction1.taobao.com/aucti ... 85582c3af2823.jhtml

这里买的，可能我不会弄

s***

我是按
belkin7231-4p潜力挖掘教程1-挂U盘
这里一步一步下来的，可还是不行

131***

原帖由 sys 于 2007-12-10 11:52 发表
我是按
belkin7231-4p潜力挖掘教程1-挂U盘
这里一步一步下来的，可还是不行

按照你的回帖,我觉得是驱动成功,但是可能分区坏了.

s***

usb驱动加载失败

s***

BusyBox v1.4.2 (2007-10-10 00:47:21 CEST) Built-in shell (ash)
Enter 'help' for a list of built-in commands.

~ # dmesg
CPU revision is: 00029007
Linux version 2.4.35 (root@dd-wrt) (gcc version 3.4.4 (OpenWrt-2.0)) #2525 Wed O
ct 10 00:49:07 CEST 2007
Determined physical RAM map:
memory: 04000000 @ 00000000 (usable)
On node 0 totalpages: 16384
zone(0): 16384 pages.
zone(1): 0 pages.
zone(2): 0 pages.
Kernel command line: root=/dev/mtdblock2 rootfstype=squashfs,jffs2 noinitrd cons
ole=ttyS0,115200
CPU: BCM4712 rev 1 at 200 MHz
Using 100.000 MHz high precision timer.
Calibrating delay loop... 196.19 BogoMIPS
Dentry cache hash table entries: 8192 (order: 4, 65536 bytes)
Inode cache hash table entries: 4096 (order: 3, 32768 bytes)
Mount cache hash table entries: 512 (order: 0, 4096 bytes)
Buffer cache hash table entries: 4096 (order: 2, 16384 bytes)
Page-cache hash table entries: 16384 (order: 4, 65536 bytes)
Checking for 'wait' instruction...  unavailable.
POSIX conformance testing by UNIFIX
PCI: Initializing host
PCI: Fixing up bus 0
PCI: Fixing up bridge
PCI: Setting latency timer of device 01:00.0 to 64
PCI: Fixing up bus 1
Initializing RT netlink socket
Starting kswapd
devfs: v1.12c (20020818) Richard Gooch (rgooch@atnf.csiro.au)
devfs: boot_options: 0x1
squashfs: version 3.0 (2006/03/15) Phillip Lougher
pty: 256 Unix98 ptys configured
Serial driver version 5.05c (2001-07-08) with MANY_PORTS SHARE_IRQ SERIAL_PCI en
abled
ttyS00 at 0xb8000300 (irq = 3) is a 16550A
ttyS01 at 0xb8000400 (irq = 3) is a 16550A
Software Watchdog Timer: 0.05, timer margin: 60 sec
PCI: Setting latency timer of device 00:02.0 to 64
Universal TUN/TAP device driver 1.5 (C)1999-2002 Maxim Krasnyansky
Physically mapped flash: Found an alias at 0x400000 for the chip at 0x0
Physically mapped flash: Found an alias at 0x800000 for the chip at 0x0
Physically mapped flash: Found an alias at 0xc00000 for the chip at 0x0
Physically mapped flash: Found an alias at 0x1000000 for the chip at 0x0
Physically mapped flash: Found an alias at 0x1400000 for the chip at 0x0
Physically mapped flash: Found an alias at 0x1800000 for the chip at 0x0
Physically mapped flash: Found an alias at 0x1c00000 for the chip at 0x0
Amd/Fujitsu Extended Query Table v1.1 at 0x0040
number of CFI chips: 1
cfi_cmdset_0002: Disabling fast programming due to code brokenness.
Flash device: 0x400000 at 0x1c000000
bootloader size: 262144
Physically mapped flash: Filesystem type: squashfs, size=0x2299d7
Creating 5 MTD partitions on "Physically mapped flash":
0x00000000-0x00040000 : "cfe"
0x00040000-0x003f0000 : "linux"
0x000c98bc-0x00300000 : "rootfs"
mtd: partition "rootfs" doesn't start on an erase block boundary -- force read-o
nly
0x003f0000-0x00400000 : "nvram"
0x00300000-0x003f0000 : "ddwrt"
Initializing Cryptographic API
IP Protocols: ICMP, UDP, TCP, IGMP
IP: routing cache hash table of 512 buckets, 4Kbytes
TCP: Hash tables configured (established 4096 bind 8192)
ip_conntrack version 2.1 (512 buckets, 4096 max) - 336 bytes per conntrack
ip_tables: (C) 2000-2002 Netfilter core team
ipt_random match loaded
netfilter PSD loaded - (c) astaro AG
ipt_osf: Startng OS fingerprint matching module.
ipt_IPV4OPTSSTRIP loaded
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
All bugs added by David S. Miller <davem@redhat.com>
VFS: Mounted root (squashfs filesystem) readonly.
Mounted devfs on /dev
PCI: Setting latency timer of device 00:01.0 to 64
eth1: Broadcom BCM4320 802.11 Wireless Controller 4.80.56.0
JFFS2 version 2.1. (C) 2001 Red Hat, Inc., designed by Axis Communications AB.
vlan1: add 01:00:5e:00:00:01 mcast address to master interface
vlan0: add 01:00:5e:00:00:01 mcast address to master interface
vlan0: dev_set_promiscuity(master, 1)
device eth0 entered promiscuous mode
device vlan0 entered promiscuous mode
device wl0.1 entered promiscuous mode
device eth1 entered promiscuous mode
device br0 entered promiscuous mode
~ #

阿***

好像根本没找到USB设备.
linux的话,用命令窗口进去,然后fdisk /dev/sdb,先用P看一下分区情况,如果用D可以删的话就用D把分区删了,如果不行,就打入X,具体操作还是要自己看一下命令的解释,把分区删了以后你可以用m来重新分区,然后按w保存退出,退出来之后,你可以用mkfs.ext3 /dev/sdb来格式化.
一般进入命令窗口你可以先看看是否是root,如果不是先打入su不然你分区后可能出现权限不足而无法保存.
我也是刚接触linux,也不是很熟悉.